Altinex PNP400 User Manual

DESIGNER SOLUTIONS

Shown with a silver finish.

MANUAL PART NUMBER: 400-0109-006

PNP400

POP ‘N PLUG®TOWER

USER’S GUIDE

TABLE OF CONTENTS

Page

PRECAUTIONS / SAFETY WARNINGS................ 2

GENERAL..........................................................2

HANDLING ........................................................2

CLEANING.........................................................2

FCC NOTICE.....................................................2

ABOUT YOUR PNP400............................................ 3

TECHNICAL SPECIFICATIONS.............................. 3

PRODUCT DESCRIPTION ......................................4

APPLICATION DIAGRAMS ...................................... 5

DIAGRAM1: TYPICAL SETUP ..........................5

DIAGRAM2: CUTOUT.......................................6

DIAGRAM3: TOP VIEW.....................................7

DIAGRAM4: FRONT VIEW................................8

DIAGRAM5: SIDE VIEW UP..............................9

DIAGRAM6: MOUNTING ................................ 10

DIAGRAM7: INSTALL A SECTIONAL PLATE .11

DIAGRAM8: CABLES/ACCESSORIES ...........12

INSTALLING YOUR PNP400................................13

OPERATION.............................................................14

INSTALL SECTIONALPLATES .......................14

TROUBLESHOOTING GUIDE...............................14

ALTINEX POLICIES................................................ 14

LIMITEDWARRANTY/RETURN POLICIES.....14

CONTACT INFORMATION.............................. 14

DESIGNER SOLUTIONS

400-0109-006

1

DESIGNER SOLUTIONS

PRECAUTIONS / SAFETY WARNINGS 1

Please read this manual carefully before using your
PNP400 and keep it handy for future reference.
These safety instructions are to ensure the long life
of your PNP400 and to prevent fire and shock
hazards. Please read them carefully and heed all
warnings.

1.1 GENERAL

• There are no user serviceable parts inside.

Qualified ALTINEX service personnel must
perform all service on the PNP400.

1.2 HANDLING

• For best results, place the PNP400 on a flat,

leveled surface in a dry area away from dust and
moisture.

• To prevent fire or shock, do not expose this unit

to water or moisture. Do not place the PNP400
in direct sunlight, near heaters, or heat-radiating
appliances, or near any liquid. Exposure to direct
sunlight, smoke, or steam can harm internal
components.

• Handle the PNP400 carefully. Dropping or

jarring can damage the unit.

• Do not pull any cables that are attached to the

PNP400.

• Do not place heavy objects on top of the

PNP400.

• Do not use excessive force to push down on the

top of the unit.

• Be careful. Serious injury could result because

of the sharp edges inside of the PNP400.

• To turn off main power, disconnect the power

cord powering the PNP400 outlets.

• We recommend using wall outlets with a Ground

Fault Circuit Interrupter (GFCI) for maximum
protection.

1.3 CLEANING

• Unplug the PNP400 before cleaning.

• Clean only with a dry cloth. Never use strong

detergents or solvents such as alcohol or
thinner. Do not use a wet cloth or water to clean
the unit. Do not open the unit to clean.

1.4 FCC NOTICE

• This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.

• This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and if
not installed and used in accordance with
instructions found herein, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.

• Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.

400-0109-006

2

DESIGNER SOLUTIONS

ABOUT YOUR PNP400 2

PNP400

POP 'N PLUG TOWER

The PNP400 Interconnect Tabletop Solution is
designed for installation into a conference room
table. The PNP400 provides a means of connecting
audiovisual, network, and power sources into a
presentation system. It is ideal for use with
ALTINEX computer video interfaces like the
VA6804FC. The PNP400 can “pop up” into a raised
position to provide access to connectors, or it can
be lowered into a table when not in use. The
PNP400 uses a tower-type construction with a gas
spring to raise the interface into position above the
tabletop.

The PNP400 Interconnect has two openings on
either side of the unit, servicing both sides of a
table. Several optional sectional plates are
available for the following: AC power, computer
video (15-pin HD), composite video (RCA), audio
(RCA), computer audio (3.5 mm stereo),
phone/modem (RJ-11), RS-232 (9-pin D-sub),
network (RJ-45), etc. Contact the ALTINEX Sales
Department for additional information regarding
optional connectors.

TECHNICAL SPECIFICATIONS 3

Specifications are subject to change.
See www.altinex.com for up-to-date information.

MECHANICAL PNP400 (standard)

Maximum Table Thickness 4.00 in (102 mm)
Minimum Table Thickness 0.25 in (6 mm)
Height Above Table (open) 2.909 in (74 mm)
Height Below Table Surface 5.760 in (146 mm)
Base Width 6.674 in (170 mm)
Base Depth 4.840 in (123 mm)
Finish Black
T° Operating 10°C-35°C
T° Maximum 50°C
Humidity

Table 1. PNP400 Mechanical

90% non-condensing

The PNP400 Interconnect is designed for use with
tables ranging from 0.25-4.0 in (6-102 mm) thick.
The PNP400 comes in a standard matte black
finish. Custom finishes for the top of the PNP400
allow the unit to accent any tabletop and are
available on a custom order basis for an additional
charge.

400-0109-006

3

PRODUCT DESCRIPTION 4

DESIGNER SOLUTIONS

POP-UP LID

GAS SPRING

MOUNTING HOLES
FOR ACCESSORY PLATES
(front and back)

BEZEL

TABLETOP

THUMB SCREW

MOUNTING
BRACKET

400-0109-006

CHASSIS

4

APPLICATION DIAGRAMS 5

DIAGRAM 1: TYPICAL SETUP

DESIGNER SOLUTIONS

400-0109-006

5

DIAGRAM 2: CUTOUT

DESIGNER SOLUTIONS

400-0109-006

6

DIAGRAM 3: TOP VIEW

DESIGNER SOLUTIONS

6.530"

[166mm]

400-0109-006

7.860"

[200mm]

7

DIAGRAM 4: FRONT VIEW

DESIGNER SOLUTIONS

2.909"

[74 mm]

400-0109-006

5.760"

[146 mm]

6.674"

[170 mm]

8

DIAGRAM 5: SIDE VIEW

DESIGNER SOLUTIONS

2.909"

[74 mm]

400-0109-006

5.760"

[146 mm]

4.840"

[123 mm]

9

DESIGNER SOLUTIONS

DIAGRAM 6: MOUNTING

2 MOUNTING BRACKETS MOUNTING BRACKETS DETAILS

TOP VIEW

2 THUMB SCREWS

SIDE VIEW

SIDE VIEW

TABLETOP

Install the mounting
brackets into the grooves
on both sides of the unit
using the grooves that
best fit the thickness of
the tabletop.

400-0109-006

Thread the thumb screws
through the mounting
brackets as shown until
the PNP400 is securely
mounted to the tabletop.

FRONT VIEW

10

DIAGRAM 7: ACCESSORY INSTALLATION

DESIGNER SOLUTIONS

ALIGN MOUNTING
HOLES

FEED CABLES
THROUGH FRONT THROUGH CHASSIS

FASTEN WITH
PLASTIC RIVETS

Feed any cables attached to the sectional plate through the front of the PNP400, then

1

down through the opening in the bottom of the chassis. Make sure the cables exit the
chassis on the same side as the plate. They should NOT cross over the center of the unit.

Align the mounting holes of the sectional plate and PNP400 chassis.

2

AND DOWN

(SP3201AV shown here.)

PLASTIC RIVETS

Insert this side

through holes

until it sits flush

with the metal.

Insert this side

all the way
down until it
sits flush with
dome surface.

AFTERBEFORE

400-0109-006

Use the plastic rivets supplied with the sectional plate to fasten the sectional plate to the

3

chassis. A rivet tool is supplied with the PNP400.

NOTE:

The plastic rivets may be removed by pressing
the center pin all the way through the material
using a small screwdriver. Then use small pliers
to remove the plastic, being careful not to scratch
the metal.

11

DIAGRAM 8: CABLES/ACCESSORIES

in Ports

Model No. Description

CUTOUT COVERS

CVR1001 Cover for PNP/TNP cutouts

SECTIONAL PLATES

SP2107US

SP2201UK

DESIGNER SOLUTIONS

Dual AC Power Outlet for United States &
Canada with 2 slots and 12 ft (4 m) metal
conduit

AC Power Outlet for United Kingdom,
Singapore & Hong Kong

SP2301CE AC Power Outlet for Continental Europe

SP2401AU

SP3102EP Dual, Empty Snap-in Ports with 1 slot

SP3103EP

SP3201AV

SP3202AV

SP3204AV

REPLACEMENT PARTS

AC401-303 Gas Spring for PNP400 Series

AC Power Outlet for Australia &
New Zealand

Dual, Empty Ortronics CAT-6 Snap­with 1 slot

15-pin HD-Female to Male + 3.5 mm
Stereo Female to Male

15-pin HD-Female to Female Gender
Changer + 3.5 mm Stereo Female to
Terminal Block
4-pin Mini DIN + RCA Female 3.5 mm
Stereo with 1 slot (universal plate for
PNP400)

400-0109-006

12

DESIGNER SOLUTIONS

INSTALLING YOUR PNP400 6

Step 1. Refer to the ALTINEX website,

www.altinex.com, to download the latest

templates and instructions for tabletop
cutting requirements and installation.

In order to do this, locate the PNP400 on
the website and go to its detail page. The
links to the templates, user’s guide, and
more are on the left-hand side of the
screen.

NOTE:The table can be 0.25-4.0 in

(6-102 mm) thick.

Step 2. Print all information applicable to the

installation of the PNP400, including the
templates and any detailed installation
instructions.

Step 3. Mark the table’s surface to indicate the

correct positioning of the unit. The face of
the unit is typically parallel to the longest
sides of the tables.

Step 7. Secure the power cord using the cable

clamp provided. Pass the power cord
(if any) from the bottom of the housing
and attach it to the table leaving a service
loop beneath the unit. Before tightening
the clamp, open and close the unit from
the top several times. Set the service loop
for smooth operation only. Do NOT leave
excessive cable hanging below the table.

Step 4. Cut an opening into the table’s surface.

This operation should be performed by
experienced professionals in order to
insure accuracy and to be aesthetically
pleasing.

NOTE: Always confirm dimensions before
cutting to insure that specifications have
not changed.

Step 5. Lower the PNP400 into the opening in the

table and make sure the bezel of the unit
sits evenly in the table.

Step 6. From under the table, insert the mounting

brackets into the slots on the side of the
unit. See DIAGRAM 6 on page 10 for
details. Place the brackets at the desired
height for the table thickness and secure
them to the bottom of the table using the
thumb screws provided. There are two
support brackets, one for each side of the
unit.

Step 8. Secure other cables from the PNP400 to

the table separate from the power cord.
All cables should be secured using a
service loop to allow the unit to open and
close easily.

Step 9. Once you have connected power and the

proper cables to the unit, you may raise
the unit. To raise the PNP400 into
position, press the top of the unit.

Step 10. To lower the PNP400, push on the top of

the unit until it locks into place. Do NOT
use excessive force to press down on the
pop-up.

400-0109-006

13

DESIGNER SOLUTIONS

OPERATION 7

7.1 INSTALL SECTIONAL PLATES

Install sectional plates in the empty slots on each
side of the PNP400 until the plates snap into place.
Secure the plates using the plastic, removable
rivets as shown in DIAGRAM 7.

TROUBLESHOOTING GUIDE 8

We have carefully tested and found no problems in
the supplied PNP400; however, we would like to
offer suggestions for the following:

• Please make sure that the highest quality video,
audio, network, and telephone cables or
connectors are used.

• If there has been damage, then do not use the
PNP400 unit. Immediately contact the ALTINEX
Sales Department to have the unit repaired.

ALTINEX POLICIES 9

9.1 LIMITED WARRANTY/RETURN POLICIES

Please see the ALTINEX website at

www.altinex.com for details on warranty and

return policies.

9.2 CONTACT INFORMATION ALTINEX, Inc.

592 Apollo Street
Brea, CA 92821 USA

TEL: [phone]
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [e-mail]

400-0109-006

14