Altec Lansing 2100 User Manual

User's guide
Mode d’emploi
Guía del usuario
Guia do Usuário

1

Rear View

Volume Up

Volume Down

Power On/Off

Power On
Indicator

The lightning flash with arrowhead, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

Caution: To prevent the risk of electric shock, do not
remove cover (or back). No user- serviceable parts
inside. Refer servicing to qualified service personnel.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.

SAFETY INSTRUCTIONS

Read Instructions — All the safety and operating instructions should be

read before the appliance is operated.
Retain Instructions — The operating instructions should be retained for

future reference.
Heed Warning — All warnings on the appliance and in the operating

instructions should be adhered to.
Follow Instructions — All operating and use instructions should be

followed.
Water and Moisture — The appliance should not be used near water –

for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.

Outdoor Use — Warning: To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.

Location — The appliance should be installed in a stable location.
Ventilation — The appliance should be situated so that its location or

position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings; or placed in a built-in installation,
such as a closed bookcase or cabinet that may impede the flow of air
through the ventilation openings.

Heat — The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers)
that produce heat.

Power Sources — The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on
the appliance.

Power-Cord Protection — Power-supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the appliance.

Grounding or Polarization — The precautions that should be taken so
that the grounding or polarization means of an appliance is not defeated.

Cleaning — The appliance should be cleaned only with a polishing cloth
or a soft dry cloth. Never clean with furniture wax, benzene, insecticides
or other volatile liquids since they may corrode the cabinet.

Non-Use Periods — The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.

Lightning Storms - Unplug the appliance during lightning storms.
Object and Liquid Entry — Care should be taken so that objects do

not fall and liquids are not spilled into the enclosure through openings.

Accessories - Only use attachments/accessories specified by the mfg.
Damage Requiring Service — The appliance should be serviced by

qualified service personnel when:

• The power-supply cord or the plug has been damaged.

• Objects have fallen, or liquid has been spilled into the appliance.

• The appliance has been exposed to rain.

• The appliance does not appear to operate normally or exhibits
a marked change in performance.

• The appliance has been dropped or the enclosure damaged.

Servicing — The user should not attempt to service the appliance.
Servicing should be referred to qualified service personnel or returned
to the dealer or call the Altec Lansing service line for assistance.

The FCC Wants You to Know

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and receiver.
c) Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.
d) Consult the dealer or an experienced radio/TV technician for help.

FCC Warning

Modifications not expressly approved by the manufacturer could void the
user authority to operate the equipment under FCC Rules.

One Year Limited Warranty

A

ltec Lansing Technologies, Inc. warrants to the end user that all of its speaker
systems are free from defects in material and workmanship in the course of normal
and reasonable use for a term of one year from the date of purchase.

This warranty is the exclusive and only warranty in effect relative to Altec Lansing
speaker systems and any other warranties, either expressed or implied, are invalid.
Neither Altec Lansing Technologies, Inc. nor any authorized Altec Lansing
Technologies, Inc. reseller is responsible for any incidental damages incurred in the
use of the speakers. (This limitation of incidental or consequential damage is not
applicable where prohibited.)

Altec Lansing Technologies, Inc. obligation under this warranty does not apply to any
defect, malfunction or failure as a result of misuse, abuse, improper installation, use
with faulty or improper equipment or the use of the computer speaker systems with
any equipment for which they were not intended.

The terms of this warranty apply only to speaker systems when such speakers are
returned to the respective authorized Altec Lansing Technologies, Inc. reseller where
they were purchased.

Under the terms of this warranty the original consumer purchases has certain legal
rights and may have other rights which vary worldwide.

Altec Lansing Technologies, Inc. is a leader in the design, manufacture, marketing
and support of high quality multimedia personal computer and home entertainment
sound systems. As manufacturers of multiple award-winning systems for both design
and sound quality, our products are at the forefront of emerging technologies.

CAUTION

To prevent electric shock do not use this (polarized) plug with an
extension cord, receptacle or other outlet unless the blades can
be fully inserted to prevent blade exposure.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Connecting the Power Cord (AC Wall Socket)

Long slot is neutral
(ground) side.

Insert the wide blade into
the ground side slot.

2

INTRODUCTION

Thank you for purchasing this Altec Lansing product. As the leader
in Powered Audio products, Altec Lansing designs, manufactures and
markets a wide range of Powered Audio systems featuring built-in
amplifiers that can transform just about any audio source into a powerful
sound system. Simply plug our speakers into your CD, MP3 and DVD
player, or your PC, TV or video gaming system—and listen
to the future of audio.

FEATURE HIGHLIGHTS

• 3 piece multimedia speaker system.

• 2 small-footprint Satellites each with 2 state of the art 1" (28 mm)
Neodymium micro drivers.

• A Subwoofer designed with two 4" (102 mm) drivers for extended low
frequency response.

• Separate Subwoofer volume control for fine-tuning system balance and
overall system low volume/high volume performance.

• Separate wired System Controller unit allows optimum speaker
placement without worrying about control access.

• A patented control circuit automatically boosts bass at low volume to
maintain musical sound "realism".

• AAC1 Y-adapter included for easy connection to gaming consoles.

The Subwoofer is not magnetically shielded and should not be placed in
close proximity to a computer monitor, television, or computer hard drive.

IMPORTANT

If you experience any difficulties with your speaker system, check the
Troubleshooting section of this Guide. The answers to most setup and
performance questions can be found there. If you cannot find the
information you need, please call our customer service team for assistance
before returning the speakers to your retailer under their return policy.
We're available 7 days a week for your convenience:

Monday to Friday: 8:00 a.m. to 12:00 midnight
Saturday & Sunday: 9:00 a.m. to 5:00 p.m.

1-800-ALTEC-88 (1-800-258-3288)

CONNECTIONS:

Do not insert the power plug into an AC outlet until all connections are made.
COLOR CODING: Notice that the Input jacks on the subwoofer are color

coded to prevent errors. The plugs that are inserted into these jacks have
matching colors. As an example, the Left Satellite has a brown
connecting plug. The plug is inserted into the Left jack with the brown
color marking located at the rear of the Subwoofer. All other connections
are made in the same way.

To insure first-time operation as expected, please follow the setup
sequence below carefully in the order indicated:

1. Connect the orange plug from the 2100 RIGHT Satellite to the jack
marked RIGHT at the rear of the Subwoofer.

2. Connect the brown plug from the 2100 LEFT Satellite to the jack
marked LEFT at the rear of the right Satellite.

3. Connect the gray DIN plug from the System Controller into the gray
DIN jack marked CONTROLLER on the Subwoofer. Note that the DIN
plug has an arrow. The arrow should be face up for correct insertion
into the DIN jack on the Subwoofer.

4. Turn off the audio source device (computer, portable music system,
etc.). Shut computer systems down using the manufacturer's
recommended procedures.

5. Connect the 6.5 ft. (5m) cable with lime green 3.5 mm stereo plugs on
each end into the jack labeled FRONT on the Subwoofer and the other
to the 3.5 mm output jack on your audio source.

NOTE: Console gaming systems have dual RCA outputs. Systems in
this group are the Sony® PlayStation®, Sega® Dreamcast™, and
Nintendo (64) gaming systems.

a. Locate the AAC1 Y-adapter cable included with your 2100 speaker

system. It has a lime green, a red and a white 3.5 mm (RCA) jack on
the ends of the "Y" cable.

b. Locate the 6.5 ft (5 m) cable with lime green 3.5 mm (RCA) stereo

plugs on each end.

c. Connect the lime green plugs to the input labeled MAIN on the

back of the Subwoofer. Connect the lime green plug on the other
end of this cable to the lime green jack on one end of the AAC1 Y­adapter cable.

d. Locate the red and white 3.5 mm RCA plugs from your powered-off

console gaming system gaming system. Connect them to the
matching red and white jacks of the AAC1 Y-adapter cable.

6. Connect the power cord (at back of Subwoofer) to an AC Wall socket.

7. The unit is now ready to operate. Turn on the audio source device.

NOTE: Always turn on your audio source device before turning on
your Altec Lansing 2100 Speaker System. If you turn on the speaker
system before turning on the audio source, you will hear a loud POP
sound when the audio device is turned on.

8. Turn on the Altec Lansing 2100 Speaker System. See USE OF
CONTROLS below.

USE OF CONTROLS

POWER ON/OFF

The Power On/Off button is located on the System Controller. Press the
Power button to turn on the speaker system. Push it again to turn the
unit off. A green LED power indicator near the power on/off button will
glow to show power is on.

VOLUME UP/DOWN CONTROLS

Press the Volume Up button on the System Controller to increase volume.
Press the Volume Down button to decrease volume. Repeated pressing
of the buttons changes the volume setting by increments.

SUBWOOFER VOLUME CONTROL (BASS LEVEL)

With the Subwoofer in the desired location, the Subwoofer Volume
control is used to mix the level of the Subwoofer with the Satellite
speakers. Mixing is usually done by playing a wide variety of music and
speech and adjusting the control until a natural sound is obtained.

PLACEMENT OF SPEAKERS

All stereo information is heard from the Satellite speakers. The
Subwoofer contains no stereo information and sound is non-directional.
As a result, the Subwoofer does not necessarily have to be placed in any
particular relationship to the Satellites. Placing the Subwoofer on the
floor close to the wall provides maximum bass efficiency.

WARNING: The Subwoofer is not magnetically shielded. The Subwoofer
should NOT be placed near video display devices such as a TV or
computer monitor. The Subwoofer should NOT be placed near computer
hard drives. Position the Subwoofer at least 2' (.6 m) away from computer
hard drives, or any other media that uses magnetic encoding.

The Satellite speakers can be placed close to a video display (TV,
computer monitor) without distorting the video image. Usually best
stereo effect is obtained by placing speakers as far apart as their wiring
allows. Sound effects may vary depending on how the recordings are
made. Therefore, it is not unusual to rearrange the speakers from time to
time until the listener finds which arrangement gives the best results.

3

TROUBLESHOOTING TIPS

SOUND PRESSURE LEVEL (SPL): 102 DB

Total Continuous Power: 35 Watts RMS
Front Speakers: 7 Watts/channel @ 4 ohms @

10% THD @ 200 - 22000 Hz 2
Channels Loaded

Subwoofer: 21 Watts @ 4 ohms
@ 10% THD @ 14 – 180 Hz

Single Channel Loaded
System Response: 40 Hz - 20 kHz (-10 dB)
Signal to Noise Ratio @ 1 kHz input: > 65 dB

SATELLITE AMPLIFIED SPEAKERS

Speaker Drivers (per Satellite): Two 1" (28 mm) micro drivers

SUBWOOFER

Speaker Drivers: Two 4" (102 mm) drivers

POWER REQUIREMENTS

USA/Canada/and applicable 120v 60Hz AC
Latin American countries:

Europe/United Kingdom; 230v 50Hz AC
applicable Asian countries;
Argentina, Chile and Uruguay:
ETL / cETL / CE / NOM / IRAM Approved

Find more troubleshooting tips in the FAQs located in the Customer
Support area of our web site: www.alteclansing.com.

Q. When connected to my computer sound card, should I use the
Windows volume control to adjust the volume of my speakers?

A. No. Adjust the Windows controls to about center as a starting point
and then use the speaker controller to adjust volume control. If the
volume is turned too high on the sound card, it can distort the sound.

Q. One, and sometimes both of my speakers do not work.
A. Check the input cable from speaker to the audio source and make

sure that it is connected to the line-out jack, which is the un-amplified
source. Make sure all the cables are plugged in correctly and have a good
connection. Still not working? Then try unplugging the cable from the
back of the computer, and insert the stereo plug into the headphone jack
of an alternate source (e.g., Walkman, Discman or FM radio) and play
music. If the speakers work, you may need to adjust your volume and
balance controls in your audio source, or Windows, if connected to your
computer's sound card

Q. My speakers give off a crackling sound (or static, or other noise).
What could be wrong?

A. Check all cables and make sure that they are connected to line-out or
audio-out jack on your sound card or other audio source, and NOT
speaker-out. If your audio source is your computer, check the volume
control in Windows: make sure that it is not set more than halfway.
Setting this level too high can cause sound distortion. If this does not
stop the noise, unplug the cable from the audio source and use an
alternate source (e.g., Walkman, Discman or FM radio) by plugging the
stereo cable into the headphone jack. If the noise goes away, you may
have a problem with your audio source.

Q. What can cause radio feedback?
A. If you are living near a radio tower you could have interference

caused by radio frequency. Try moving your speakers to see if the
interference goes away; if not, you may be able to purchase a stereo
cable from your local retailer that has a higher percentage of shielding.

Q. Can I hook my speakers to my TV or Stereo?
A. Yes, as long as your TV or Stereo has an unamplified source which is

line-out (check your TV or Stereo owners manual). These speakers may be
used with any audio device that has a stereo headphone jack. You may
also need a cable that has RCA jacks on one end and a 1/8 inch stereo
connector at the other end (these may be purchased at most local
electronics stores).

Q. I have very little bass coming from my Subwoofer. How do I increase
the bass output?

A. Adjust the BASS control through your audio sound source (computer
sound card control, CD player control, etc.). Check to make sure that all
of your cables are hooked up correctly and are making a good
connection.

Q. I have a low hum coming from my Subwoofer. Is this normal?
A. Yes. The AC in your house is at 60 cycles per second, which is within

the audio frequency of your subwoofer. Some low hum is natural and can
be detected when your speaker system is powered on without source
audio playing, or when volume is set at an extremely low level.

Q. I have a loud hum coming from my Subwoofer. What should I do?
A. Move the power cord from the power surge protector (if applicable)

and plug directly into an AC wall outlet. Move your cables and check to
see that they are making a good connection. If you disconnect your
stereo cable from the audio source and the loud hum goes away, then
you may need to adjust the volume control in your audio source as you
may be overdriving the volume settings on your speaker system. If you
are using your 2100 speakers with your computer system, just click on the
speaker icon located next to the digital clock to the lower right of your
Windows 9X or 2000 screen and adjust the volume.

Q. When I put my Subwoofer on my desk my monitor distorts. Why?
A. The Subwoofer is not magnetically shielded, and this can cause

distortion if it is less than 3 feet from your monitor.

Q. Where should the volume control be set on my Subwoofer?
A. Start with it in the center position then adjust to your preference.

Q. The DIN connector from the controller has multiple pins on one end,

and when trying to attach this cable I noticed that some of the pins are
bent, so I am not able to insert the cable into Subwoofer. What should I do?

A. Try to gently straighten the pins with tweezers or very small pliers. If
this does not work, then contact the Altec Lansing Consumer Support
Department for further instructions.

SPECIFICATIONS

4

Power rating conforms to FTC Amplifier Rule #16 C.F.R. Part 432. Altec Lansing’s superior sound comes from our patented Dynamic EQ

technology, which utilizes custom-built, high-fidelity drivers, state-of-the­art equalization circuitry, and a harmonious mix of the following
specifications: