Page 1
Advanced Dual Display, 3 Outputs Temperature Controllers
E253771
FEATURES
• 4 + 4 digits , 7 segment LED dual display
• TC / RTD Input, Analog input
• ON-OFF, PID
• Heat Cool PID
• °C / °F
• Ramp Soak
• Soft Start
• RS485 Communication (PID500 only)
CAT. NO.
Display
Display Type 7 Segment LED Display
Digits 2 rows of 4 digits
Resolution 1/0.1 Degree for TC/RTD / Fixed 1 Degree for R, S & T / Decimal point position selectable 1/0.1/0.01/0.001 for analog input
Supply Specification
Input Voltage 85-270V AC/DC (50/60Hz)
Input Specification
Input Measurement Thermocouple (J,K,T,R,S,C,E,B,N,L,U,W, Platinel II) / RTD (Pt100) Signal Inputs (-5 to 56mV, 0 to 10V, 0 to 20mA)
Sampling Time 200msec
Input Filter (FTC) 1 to 99 sec
Output Specification
Main Output Selectable- SPST- 10A @230V AC / 30V DC, resistive OR SSR Drive(Voltage Pulse)- 12V DC, 50mA OR Current- 4-20mA DC
Auxillary Output 2 Selectable- SPST- 5A @230V AC / 30V DC, resistive OR SSR Drive(Voltage Pulse)- 12V DC, 20mA
Retransmission 4 to 20mA DC, 0-10V DC (100msec. Update Rate)
Functional Specification
Control Action 1) PID Control with Auto Tuning 2) ON-OFF Control
PID Proportional Band (P): 1-400 Integral Time (I): 0-3600sec Derivative Time (D): 0-200sec
Alarm Modes Deviation High/Low, Absolute High/Low, Band, Sensor Break PID330- Full Scale High, Full Scale Low
Hysteresis 0.1-99.9
Temperature Unit °C / °F
Cycle Time 0.1 to 100 sec.
Manual Reset Value -99.9 to 19.9
Power Consumption 5VA max @230V AC
Set Points 2
Accuracy
CONTROL
TC INPUTS 0.25% of F.S. ±1
R, S INPUTS 0.5% of F.S. ±2
RTD INPUT 0.1% of F.S. ±1
Environmental Specification
Operating Temperature 0 to 50C (32 to 122F)
Storage Temperature -20 to 75C (-4 to 167F)
Humidity (Non-Condensing) 85% Relative Humidity
Weight See dimensions on next page
Ordering Information
Part No. Output 1 Output 2 Output 3 Supply Voltage
Relay/SSR RS485
PID500-0-0-01-CU Relay Relay Relay – 85-270V AC/DC
PID500-1-0-01-CU SSR Relay Relay – 85-270V AC/DC
PID500-0-0-04-CU Relay Relay Relay Yes 85-270V AC/DC
PID500-1-0-04-CU SSR Relay Relay Yes 85-270V AC/DC
PID500-1-1-04-CU SSR SSR Relay Yes 85-270V AC/DC
PID500-2-0-04-CU 4-20mA Relay Relay Yes 85-270V AC/DC
PID500-3-0-04-CU 0-10V Relay Relay Yes 85-270V AC/DC
PID110-0-0-01-CU Relay Relay Relay – 85-270V AC/DC
PID110-1-0-01-CU SSR Relay Relay – 85-270V AC/DC
PID330-0-0-01-CU Relay Relay Relay – 85-270V AC/DC
PID330-1-0-01-CU SSR Relay Relay – 85-270V AC/DC
PID500 PID110 PID330
Mounting Accessories (supplied with units)
For PID500: 48 X 48 Collar clamp ACL4802
For PID110 and PID330: Clamp side with screw assembled
22
Page 2
Advanced Dual Display, 3 Outputs Temperature Controllers
48mm
48mm
45mm
45mm
100mm
45mm
7mm
Panel Cutout
RTD3
+
-
RS485
12
7
13 8
14
9
15 10
COM2
SSR1/ 0-5 V/
0 -10 V/4 -20mA
SSR2
NO1
COM1
NO2
2
1
3
4
5
+
-
+
-
L (+)
6
11
(-) N
COM3
NO3
+
-
SSR3
ANA IP
TC /RTD1
+
+
ANA IP
TC /RTD2
-
-
Panel Cutout
Panel Cutout
DIMENSIONS TERMINAL CONNECTIONS
PID500
Weight: 95 grams (.43 lbs)
Serial Communication
Interface standard RS485
Communication address 1 to 99, maximum of 32 units per line
Transmission mode Half duplex
Transmission protocol MODBUS RTU
Transmission distance 500 m maximum
Transmission speed 9600, 4800, 2400, 1200, 600, 300 bits / sec
Parity Non, Odd, even, Mark, Space
Stop bits 1 or 2
Response Time 100 ms (Max and independent of boud rate)
PID110
PID5330
Accessories (Optional)
Standard SELEC accessories that can be used with this product.
Adapter plate
1) AP7248: Plastic adapter plate, used to mount 1/16 DIN (cutout size 48 x 48); Instrument into existing (72 x 72) cutout size.
2) AP9648: Plastic adapter plate, used to mount 1/16 DIN (cutout size 48 x 48); Instrument into existing (96 x 96) cutout size.
3) AP4896-4848-G-C:
Plastic adapter plate, used to mount 1/16 DIN (cutout size 48 x 48) Instrument into existing (48 x 96) cutout size.
DIMENSIONS TERMINAL CONNECTIONS
CONTROL
Weight: 250 grams (.55 lbs)
DIMENSIONS TERMINAL CONNECTIONS
Weight: 295 grams (.65 lbs)
23
Loading...