Altech DIN35, DIN32, DIN13, CA603, TSTW Catalog Page

DIN Rail Mounting

Altech DIN Rails comply with EN
60715 and DIN 50045, 50022 and
50035 standards. DIN Rails have been
accepted throughout the world,
allowing the equipment or panel
builder to mount a wide variety of
control components, devices, termi­nal blocks, power supplies, etc. on the
same rail. The use of DIN Rails
enhances design capabilities, saves
space and reduces labor.

Standard rails are made of regular
steel with galvanic zinc plating and
passivation and are available in vari­ous configurations. Aluminum and
stainless steel rails are also available
but only in 35 mm size and 7.5 mm
deep.

Standard DIN Rails are available in
35mm (7.5 and 15mm deep), 32mm
and 15mm widths and are supplied in
1 m (3'3") and 2 m (6’6”) lengths.
Upon request they can be cut to cus­tom lengths and punched with cus­tom holes or perforations.

DIN35 DIN35

Type

Perforated
Steel

Unperforated
Steel

Perforated
Stainless Steel

Unperforated
Stainless Steel

Perforated
Aluminum

Unperforated
Aluminum

Preforated Steel and Stainless Dimensions

Cat. No. Length Std. Pk.

2511120 2m 20
2511120/1M 1m 40

2511110 2m 20
2511110/1M 1m 40

2511125 2m 20
2511125/1M 1m 40

2511115 2m 20
2511115/1M 1m 40

2511121 2m 20
2511121/1M 1m 40

2511111 2m 20
2511111/1M 1m 40

18

35 mm x

7.5 mm deep

Type

Perforated
Steel

Unperforated
Steel

35 mm x

15 mm deep

Cat. No. Length Std. Pk.

CA701-15/S-2M 2m 10
CA701-15/S 1m 20

CA701-15-2M 2m 10
CA701-15 1m 20

• 35mm, 32mm, 15mm

• Perforated or un-perforated

• Standard rail is steel with galvanic
zinc plating and passivation

• Aluminum Rail is made of
Aluminum

• Stainless steel rail is made of AISI
304 type stainless steel

Support Brackets

Support Brackets elevate DIN Rails
away from the panel to facilitate
component mounting and to
increase wiring access. Angled brack­ets tilt the rail by 35° to improve visi­bility. Straight brackets are available
in three heights for optimum posi­tioning of the rail.

Brackets mount with 2 screws to any
panel or flat surface and have tapped
center holes for rail mounting.
Bracket material is steel, zinc plated
yellow chromated.

Preforated Aluminum Dimensions

25.4

Unpreforated Dimensions

CA603 TSTW

M6

48mm

(1.89in)

60mm (2.36in)

74mm (2.91in)

Suitable for all mounting rails

Cat. No. Std. Pk.

CA603 25

12.7

Ø7mm (.28in)

4.6

18mm
(.71in)

18

M6

Ø6mm

(.24 in.)

52mm(2.05 in.)

74mm(2.98 in.)

Complete with rail mounting hardware:

including one screw & one locknut

Height

1“
2”
3”

Cat. No. Std. Pk.

CA703 25
CA803 25
CA903 25

Slot 6x15mm
(.24x.59 in.)

18mm(.71in.)

H

2

DIN32 DIN15

18

DIN Rail Mounting

Type

Perforated
Steel

Unperforated
Steel

mm x

32

15 mm deep

Cat. No. Length Std. Pk.

2511160 2m 10
2511160/1M 1m 20

2511150 2m 10
2511150/1M 1m 20

Type

Perforated
Steel

15 mm x

5.5 mm deep

Cat. No. Length Std. Pk.

CA601/S 1m 50

3