INSTRUCTION MANUAL
ALSATOM SU 50-MPC, SU 100-MPC, SU 140-MPC, SU 140/D-MPC
This unit is manufactured by ALSA APPARECCHI MEDICALI S.R.L., Via C. Bonazzi 16 , 40013 Castel Maggiore (BO), Italy, that guarantees its safety,
reliability and performances only if installa tion, recal ibrations and repairs are carried out by personnel authorized by ALS A a nd if the unit is used in
compliance with t he given instructi ons in an area tha t meets all the applicable IEC or CE I r equirements. T he manufacturer is at dis posal t o supply, if
requested, the electric diagrams and any further information.
In accordance with the ALSA procedures for the after-sale control of the production, the users are pleased to inform the Manufacturer about every,
even little, problem of this unit.
INTRODUCTION
In a biological tissue crossed by an electric current are shown the following effects:
- thermal, faradic, electrolytic.
By using HF electric curr ent the last 2 und isired and useless ef fects are eliminated and it is utilized above all the thermal e ffect. In fact
when an electric current having such characteristics flows, from the active electrode to the neutral one, with sufficient density the cellular
liquid of the tissues warms it and produces the following effects:
1) heating is so quick that the pressure of the vapour created in the cells breaks their membranes (cutting);
2) heating is lower, so the liquid slowly evaporates allowing the coagulation of the coagulable components of the tissues (coagulation or
haemostasis);
3) the effect is a middle way between the two above-described ones (cut with coagulation).
The ESU is “ HF device” that may destroy the cells of biological tissues and therefore it should be used by expert staffs in el ectrosurgery
and respecting strictly all the given instructions.
The ALSATOM SU-MPC series can be used for every kind of monopolar/bipolar cut and coagulation/microcoagulation in:
GYNAECOLOGY, DERMATOLOGY, PLASTIC SURGERY, DENTAL AND MAXILLO-FACIAL SURGERY, ANGIOLOGY,
GENERAL SURGERY, ORL, GASTROENTEROLOGY, VETERINARY.
In particular, the functions are as follows:
- CUT: Monopolar pure cut without coagulation
- BLEND: Monopolar cut with coagulation
- COAG: Monopolar coagulation (high voltage-fulguration)
- COAG MICRO Monopolar coagulation (low voltage-soft)
- BIPOLAR Bipolar coagulation.
Before using these units, control their performance (for example on a piece of meat) without relying completely on the previous
experiences with other devices. Always start with very low powers, then gradually raise up until obtain the desired surgical effect.
GENERAL PRECAUTIONS – It is dangerous to ignore the following warnings:
1- It is dangerous to use the device if the operating theatre doesnot meet CEI/IEC electrical requirements.
- Do not use “extension leads” for the power s upply cable. Co ntact the technical d epartment for the com patibility of o ther
equipment eventually in use.
2- It is extremely dangerous to use accessories or instruments which are not perfectly compliant with all the applicable technical or
legislative Rules, and which are not suitable f or the wo rking voltag es of th e device ( approx. 2800Vpp “1500Vp” for the
monopolar currents with cr est factors equal or higher th an 2; 120 0 Vpp “600Vp” for the monopolar currents with crest factors
lower than 2; approx. 400Vpp “220Vp for the bipolar currents with crest factors equal or lower than 2). Moreover, the accessories
and instruments must not be old nor worn. Check always their status before the use, notably if for endoscopy. Bear in mind that:
- All the old/worn active electrodes, accessories and cables do not work properly, and do not guarant ee the perfect insulation. In
addition, their unstable functioning can lead the operator to increase the output powers at dangerous levels;
- In the user manual, for each current, the maximum output voltage “Vpp” and its variation (see the curves) according to the output
power adjustment are specified. This allows the operators to choose the maximum output power th at must not be overcome, in
order to not exceed the rated HF insulation voltage, which is possible for each accessory;
- The stand
handles are suitable for the electrodes having stems with this diameter).
3- The interference of HF units may harm the other electromedical equipments in use.
4- Contact cardiological department when using a HF unit on patient with pace-maker (the device can interfere its efficiency causing
fibrillations and ect. or damage their electrodes).
5- Always take metal objects off the patients (ring, chain and etc.). Do not use a HF unit in the presence of flammable anaesthetic
gases (i.e. oxygen, nitrogen protoxide and etc.) especially if operating in cavities (chest, abdomen, trachea, head, etc.)
6- Do not use flammable cleanin g substances, disinfectants or s olvents, or a t l east c arefully ev aporate th em be fore oper ation.
Always remove the remaining substances from hollow parts of the body or cavities (umbilicus, vagina, etc.) and from underneath.
While using the device, a spark may caus e the endogenous gas (intestin e) explosion or set fire to ox ygen satu rated material
(cotton, gauze, etc.).
7- Prevent the patient from touching an y metal parts connected to earth or electricity conductors (table, supports, etc.) and isol ate
strongly secreting parts of the body and skin-to-skin contacts by using dry covers (i.e. between arm and body).
8- Position monitoring electrodes (not specif ically s hielded) as fa r as pos sible fr om the el ectrodes of the HF u nits. If pos sible
avoiding the needle type or small-sized ones.
9- Use and position the neutral electrode as follows:
- Choose an area of the body as near as possible to the area to be operated (the ideal is a flabby part without hairs where there
ard monopolar activ e electrodes for n ormal surger y h ave a stem with Ø 2.3mm ( so, the stand ard electrode-ho lder
are no protruding bones or uneven surfaces). Clean it, shave it and massage it to favour circulation.
MN SU-MPC ING March 2008 Page 1 of 9
- Firmly fix the electrode without placing anything in-between, ensuring the best contact possible over the entire surface but
without pressing too hard to avoid creating ischemic areas (maybe use conductive gels, etc.) and always make sure that the
contact is constant, especially if the patient is moved or when liquids are poured.
10- The position of the neutral electr ode with regard to the operating area creates an HF current route and remember that any metal
objects (prostheses, catherters, etc.) in that area may cause current concentrations that heat or even burn the adjacent tissue.
11- Position the cables of the electrodes so that they do not touch the patient or other wires.
12- Always use the lowest power possible to the surgical need.
The insufficient performance of the equipment may depend on: wrong positioning or fault y contact of the neutr al plate, f aulty
connection of electrodes, poor conditions of the active electrode and therefore check these factors before increasing the power.
13- Use the bipolar technique for operating on small portions of tissues or in cavities.
14- When the unit is in use, don’t touch with the active electrode the neutral one (short circuit) and try to avoid the activation when
the active electrode doesn’t touch the tissues – it might damage the unit or r educe its life. Please respect the suggested working
times.
15- Contact the Technical Department for the use of “disposable” electrodes.
16- In case lack of supply mains, turn off the unit (setting output power at ZERO).
17- Pay attention that the fault of the HF unit might cause an unexpected power increase.
POSITIONING OF THE PATIENT AND USING OF NEUTRAL PLATE
By using monopolar technique, it is v ery important that all the currents reach ing the pa tient must return to the unit via the neutral plate,
otherwise two serious consequences will be encountered:
1. HF current d ischarges from th e patient through an insufficient part of the same neu tral plate or via casual contacts of conductive
objects (operating table, wet clothes, supports and etc.), since these contact surfaces can be insufficient, the current crossing them may
cause some burns.
2. Output power may lower considerably
Therefore use and position the neutral plate respecting the par. “General Precautions”.
Remember that, using a HF unit, it may occur phenomena generally named as “shocks” but these phenomena are normally only
stimulations or radiofrequency discharges depending on the same contact between the operator and the patient. In case they
happen it is advisable that the operator avoids the direct contacts with patient (e.g. use surgical gloves as insulating) and, if
possible, has not ground contact (use clogs, insulating chair, and so on…).
SAFETY CIRCUIT OF THE NEUTRAL PLATE
The unit is equipped with the neutral plat e connection control circuit that, when the monopolar performance is selected, blo cks the output
power (if the neutral electrode is not connected or the relevant cable is broken) with specific alarm (intermittente sound and red light).
circuit doesn’t occur when the bipolar coagulation is selected but the red light signal is put on.
This
WAY TO USE AND PRATICAL PROPOSALS
1. Check the power supply mains (it must corres pond with the tech nical data at the back) and connect the device with main switch ( 1)
position OFF. Connect the pedal switch tubing (socket 3 at the back) crew tightly the connector without pushing on the pedal (the
mod. 140/D is provided with 2 sockets for the double pedal switch and the connection must be performed as follows: yellow
tubing of the double pedal to the left socket with yellow area, blue tubing of the double pedal to the right socket with blue a rea ). The
pedal is pneumatic type, without electric current, waterproof and explosion proof.
2. Connect the electrodes as follows:
- neutral electrode (socket 6) and active electrode (socket 7)
Modd. 140 and 140/D: hand-switch pencil (7A) pedal-switch pencil (7B). For endoscope cables and etc. use only socket 7B,
if neccessary ask for specific adapters.
- Bipolar electrode (socket 8 without any polarity of the pins)
The ALSA standard bipolar cable has this following connector:
3. Put on the unit by the switch 1
4. Set up the initial power as follows:
- modd. SU 100 and SU 50 by control 5,
- modd. SU 140 and SU 140/D b y control 5A ( pure cut or blen d cut) , and control 5B (co agulation, micro- coagulation, b ipolar
coagulation).
5. Select the performance by selector 4 and activate the output as follows:
modd. SU 100 and SU 50 ............ (selector 4 - position: cut, blend, coag., micro coag., bip. coag.) activation by single pedal switch;
mod. SU 140/D ............................ (selector 4 – position: cu t/ coag., cut/micro coag., blend/coag.,) activation by hand switch pencil
or double pedal switch (yellow for cut, blue for coagulation);
(selector 4 – position: bip. coag.) activation by only the pedal switch (blue);
m od. SU 140 ................................ (selector 4 – position: cut/coag.) activation by hand switch pencil;
(selector 4 – position: cut, blend/coag., micro coag., bip. coag.) activation by single pedal switch.
The activation is indicated: cut/blend by yellow light and low acoustic signal, coag./micro coag. by blue light and high acoustic signal,
bipolar coag. by blue light and louder acoustic signal.
To optimize the
1. Do not activate the unit before touching the tissues by the active electrode (otherwise they will creat electric arcs able to p roduce
eschar on tissue and preventing them from good cicatrization).
2. Keep the active electrode as clean as possible. The patina insulating on an electrode doesn’t permit a good contact with the ti ssues,
thus it lowers the output power and causes sparks or superficial carbonizations.
running of the units follow the following general indications:
MN SU-MPC ING March 2008 Page 2 of 9
3. Using the pure cut (especially with the loop/conization electrodes) if the first effect is not satisf actory (with a slight sticking of the
tissue on the electrode), to have the best result increase the power of 10÷15 W each time.
Pure cut (for biopsy, laparoscopy, cut or skin incision, uterine conization in gynaecology etc., in general for any
case needing cut without coagulating effect).
1. Use small size electrodes, such as for ex.:
• “thin needle electrode” (from 3÷4 W onwards)
• SAD, SAD/1, SAD/2, SAD/3 “extra-f ine needle electrod es” no t insulated w ith diam. from 0.10 to 0.40 mm (from 3÷4 W
onwards)
• “fine loop electrodes” of different measures and shapes (from 8W onwards).
• “long type electrodes” and “LLETZ type electrodes for gynaecology” (from 10W onwards)
2. Select “CUT” current
Cut coagulating (for laparoscopy, polypectomies or papillotomies in endoscopy, fistulas, haemorrhoids and ect. In
general for any case needing cut combined with an effective coagulating effect).
1. Use the electrodes already mentioned for pure cut or, if possible, the ones with larger section, such as for ex.: knife and thick needle
electrode (from 3÷4 W onwards)
2. Select “BLEND” current and sl ow a little th e sliding of the el ectrode on the tissue . If coagulati ng effect is not enough, use even
“COAG.” current.
Micro coagulation
1. Use extra fin e needles: AID “in sulated needle” (the best for depilation), all the above mentioned “SAD” long ty pe, not insulated
needles for depilation, telangiectasia, spider naevi, pointformed red-ruby angiomas and ect.
2. Use ball electrodes to obtain deep effect avoiding as much as possible a surperficial sparking.
3. Select “COAG MICRO” current (from 0.5 Watt onwards)
Coagulation
1. Use ball electrodes, surgical forceps for coagulation with effective deep effect and good surperficial effect (fulguration).
2. Use small ball, needle, loop or for polipectomy electrodes, etc. to obtain strong superficial effect and limited deep effect.
3. Select “COAG” current (from 2-3 W onwards).
Bipolar coagulation
1. Use bipolar forceps or bipolar electrodes (also for laparoscopy or endoscopy, eventually supplied by the other manufacturers).
2. Select “BIP” current (from 2-3 Watt onwards)
3. Please remind that, to reduce the “sticking phenomena” of the tissue on the tips of the bipolar forceps during the operation, it is very
useful to clam them as little as possible, reduce at maximum the time of activation and moisten them by physicological solution (or
plunged inside a cup or on an imbibed gauze).
AUTOTEST
The running of the unit is completely
which, if regu lar, ends with short acous tic signal). If an y failure the s ystem get blocked the output giving specific error cod es (acoustic
signals).
TYPE OF FAILURE
1. me mory RAM 1
2. CRC control software 2 “
3. variables of the system 3 “
4. supply voltage of microcontroller 4 “
5. act ivation circuits 5 “
6. output power higher than the selected value 6 “
7. incorrect use of the selector 4 7 Check the position of the selector
8. got broken control 5 8 As specified for Fault 1
9. continuous activation for more than 20s 9 Deactivate and reactivate immediately
10. R.F. modulation signal 10 As specified for Fault 1
11. monitoring of the output current 11 “
12. monitoring of R.F. supply 12 “
13. watchdog timer 13 “
14. intervention of neutral plate safety circuit
15. usage error (eg. Activation of cut function if
selecting BIP or activation of 2 switches
comtemporally)
Furthermore the following cases may occur:
1. the unit is ON (autotest OK), but when you press the pedal switch, it does not work (without acoustic or ligh t signals) or work s
irregularly.
a) check if the pedal is well connected;
b) check if the pedal is broken b y activating the un it pushing th e central ho le of th e relevant socket with a round
point. If the unit works regularly it is probably a problem of pedal.
2. the unit is ON (autotest OK), all the running is OK, but there is not output power or it is lower than the normal value.
a) check the good contact of the neutral plate (if the contact is bad or absent there is no power). Remember that the
hair of animals is insulating.
controlled b y microcontr oller both durin g the working and when switching on (starting aut otest
NO. OF
ACOUSTIC
SIGNAL
intermittent
(grave)
Intermittent
(acute)
Turn off and re-switch on the unit (if the problem
continues, contact the technical assistance)
Check the connection of the plug and the cable (bend
and pull it, especially near the plug and the electrode).
If the problem continues, contact the technical
SOLUTION
assistance)
Eliminate the cause
MN SU-MPC ING March 2008 Page 3 of 9
b) check if the active electrodes are damaged, if the contact with the pencil is good, if the pencil cable is broken
(pull and bend it, especially near the plug and the handle).
If all the above mentioned interventions do not resolve, please contact the Technical Assitance.
TECHNICAL FEATURES
• Electronic generator in compliance with the Safety Standards IEC 601-2-2 3^ed.
• Monopolar and Bipolar working frequency: 475 kHz
• Classification IEC: I type CF – Classification EC MDD: IIB
• Output circuit: “floating out” protected against the use of the defribrillator
• Mains and Absorption: see rating on the back of the unit
• Mains Fuses: see rating on the back of the unit
• Neutral plate safety circuit with acoustic signal (strong, intermittent) and luminous signal (red)
• Output power : setting by rotary switches
• Running control: by microcontroller with autotest, output error control, error codes
• Protection against liquids: common, not-protected casing
• Cooling by convection without ventilator
• Activation: discontinuous, 10s ON/30s OFF
• Dimensions and weight:
cm (LxDxH) 23x24x10 – Kg 4.75 (modd. SU 140-MPC and SU 140/D-MPC)
cm (LxDxH) 21x24x10 – Kg 4.50 (modd. SU 50-MPC and SU 100/D-MPC)
Conformity EMC/Directive 89/336/CEE: Category A
Suggested distances to keep from not vital devices
Microcellular telephones CT1,CT2,CT3 0.01 0.4
Mobile telephones DECT, Wireless devices (modems, LANs) 0.25 2
Mobile telephones (USA) 0.6 3
Hand mobile telephones (GSM, NMT, Europe)
(DECS 1800)
Walkie-talkie (police, firemen , protection, maintenance) 5 9
Bag mobile telephones 16 16
Mobile radio (police, firemen, protection) 100 40
For broadcasting stations which use frequencies less than 800MHz, the distance can be established by using the equation: A: d = 4√P
For broadcasting stations which use frequencies between 800MHz and 2.5GHz, the distance can be established by using the equation:
B : d =2.3√P
P = Nominal power of the transmitter in watt (W), established by the manufacturer.
Source of the Current RF Typical Power (W) Distance (m)
2
8
6
11
Output power, Vpp-open circuit, Crest factors (SU 100-MPC, SU 140-MPC, SU 140/D-MPC)
Cut: 140 WRMS at 500 Ohm (Vpp 1200, cf 1.7)
Blend: 120 WRMS at 500 Ohm (Vpp 1450, cf 2.8)
Coag: 120 WRMS at 500 Ohm (Vpp 1952, cf 6.9)
Coag Micro: 60 WRMS at 200 Ohm (Vpp 1420, cf 2.8)
Bipolar: 100 WRMS at 100 Ohm (Vpp 400, cf 1.4)
Output power, Vpp-open circuit, Crest factors (SU 50
Cut: 80 WRMS at 500 Ohm (Vpp 1000, cf 1.7)
Blend: 80 WRMS at 500 Ohm (Vpp 1420, cf 2.8)
Coag: 80 WRMS at 500 Ohm (Vpp 1950, cf 6.9)
Coag Micro: 60 WRMS at 200 Ohm (Vpp 1420, cf 2.8)
Bipolar: 60 WRMS at 100 Ohm (Vpp 400, cf 1.4)
-MPC)
ATMOSPHERIC CONDITIONS
usage transport and storage
Temperature (°C) +10 ÷ +40 Temperature (°C) -40 ÷ +70
Humidity 30% ÷ 75% Humidity 10% ÷ 95%
Pressure (hPA) 700 ÷ 1060 Pressure (hPA) 500 ÷ 1060
CLEANING, STERILIZATION, MAINTENANCE, DISPOSAL
1. Clean the unit by neutral soap solution (pay attention: any liquid doesn’t go inside) and wipe it, keep in a dry and not-dusty place
and ensure that is not poured any liquid on it.
2. The unit must be periodically checked (at least once per year) by qualified staff, better by the Manufacturer. Always control the
accessories, if they are not in p erfect condition they can be d angerous (eg. Bro ken cables, dirty electrodes, pins clamped b y jury
means and etc.)
3. Waste of the unit must respect every specific national rules.
4. Attention, at the moment of the sale the accessories are not sterile. All the monopolar and bipolar accessories are sterilizable
by autoclave (121°C) or by cold solution (ex. Cydex), the neutral plates by cold solutions only. Sterilize them as indicated in
the instruction of every single package.
STANDARD ACCESSORIES
MPE/E - Sterilizable pencil with connection cable.(Rated voltage = 4000 Vp)
SEL/VI - Set of 6 electrodes. (Rated voltage = 4000 Vp)
EIP/9 - Neutral plate with connection cable.
FFE - Fixing rubber belt for neutral electrode.
D-STOP/P - Double pneumatic pedal switch (mod. SU 140/D-MPC)
STOP/PN - Pneumatic pedal switch (modd. SU 50-MPC, SU 100-MPC, SU 140-MPC).
MN SU-MPC ING March 2008 Page 4 of 9
CONTROLS AND SYMBOLS
11
4
11
4
910
ALSATOM SU 140/D
4
655
77ABAB
910
ALSATOM SU 100 ALSATOM SU 50
8
675
4
11
11
10 9
55 6
10 9
576
ALSATOM SU 140
BA BA 77
8
At the back
1- Main switch …………. symbol: (switching on) (switching off)
2- Power entry module with double fuse-holder
3- Connection pedal switch ………symbol
only 140/D model:
A = cut (yellow signal)
B = coagulation (blue signal)
In the front
4 Function selector
5 Output power setting (modd. 140 and 140/D:A = pure cut and blend cut; B= coagulation, micro coagulation, bipolar coagulation)
6 Neutral plate socket ................................. symbol:
7 Active electrode socket (modd. 140 and 140/D: A= hand switch handle ...... symbol:
( “ “ B= pedal switch handle ..... symbol:
(modd. 100 and 50 ..................................................... symbol:
8 Bipolar electrode socket ................................................................................... symbol:
9 Output activation/coagulation: (blue light) with display (only modd. 140 and 140/D) ....................... symbol:
10 Output activation/cut: (yellow light) with display (only modd. 140 and 140/D) ................................. symbol:
11 Neutral plate safety circuit (red light) .............................................................. symbol:
Be careful: read the annexed documentation: .......................................................... symbol:
Apparatus of Class I - Type CF – protected against the effect of the defibrillator ... symbol:
Alternating current ................................................................................................... symbol:
MN SU-MPC ING March 2008 Page 5 of 9
POWER OUTPUT DIAGRAMS (± 20% ) – Modd. SU 100-MPC, 140-MPC, 140/D-MPC (NOTE: in model SU 140-MPC, BLEND
diagram corresponds to BLEND/COAG position of the mode selector)
SETTING
REGLAGE
IMPOSTAZIONE
10
9
8
7
6
5
4
3
2
1
700
800
900
1000
1200
1100
1300
(V)
Vp-p
400
500
600
100
200
300
Vp-p
IMPOSTAZIONE
SETTING
REGLAGE
10
9
8
7
6
5
4
3
2
1
1200
1500
1400
(V)
1000
1100
1300
600
800
700
900
200
400
300
500
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
100
Vp-p
SETTING
REGLAGE
IMPOSTAZIONE
10
9
8
7
6
5
4
3
2
1
1600
1700
1800
1900
2000
(V)
1500
1400
900
1300
800
1100
1000
1200
300
500
400
700
600
2001100
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
WRMS
908070
120
110
100
130
Ω)
(@ 500
WRMS
CUT Pos."10"
70
80
90
100
110
120
130
140
CUT Pos."5"
20
30
40
50
60
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
10
RMS
W
RMS
W
130
90
100
110
120
Ω)
(@ 500
908070605040302010
120
110
100
50
60
70
80
BLEND Pos."10"
10
20
30
40
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
BLEND Pos."5"
500
400
300
200
100
WRMS
RMS
W
140
130
302010
605040
90
807060
110
100
120
Ω)
(@ 500
COAG Pos."10"
706080
90
110
100
120
302010
50
40
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
COAG Pos."5"
50
500
400
300
200
100
10
204030
MONOPOLARE
MONOPOLAR PURE CUT
TAGLIO PURO
MONOPOLAIRE
SECTION PURE
MONOPOLARE
MONOPOLAR BLEND CUT
TAGLIO BLEND
SECTION AVEC
COAGULATION
MONOPOLAIRE
MONOPOLARE
MONOPOLAR
COAGULAZIONE
COAGULATION
COAGULATION
MONOPOLAIRE
MN SU-MPC ING March 2008 Page 6 of 9
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
200
100
300
500
400
700
600
900
1300
1200
1500
1400
(V)
Vp-p
800
1100
1000
10
9
8
7
6
5
4
3
2
1
IMPOSTAZIONE
500
(V)
Vp-p
SETTING
REGLAGE
300
400
100
200
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
30
40
RMS
W
50
60
Ω)
(@ 200
COAG MICRO Pos."10"
301020
40
70
WRMS
50
60
10
20
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
COAG MICRO Pos."5"
400
300
200
100
100
Ω)
RMS
W
(@ 100
RMS
100
110
W
60
80
70
90
BIPOLAR Pos."10"
806070
90
20
40
50
30
10
Ω
1000
900
800
700
600
500
400
300
BIPOLAR Pos."5"
200
100
50
10
50
201030
40
MONOPOLARE
MONOPOLAR MICRO
MICRO COAGULATION
COAGULAZIONE MICRO
COAGULATION
MONOPOLAIRE
BIPOLAR COAGULATION
COAGULAZIONE BIPOLARE
COAGULATION BIPOLAIRE
MN SU-MPC ING March 2008 Page 7 of 9
POWER OUTPUT DIAGRAMS (± 20% ) – SU 50-MPC
SETTING
REGLAGE
IMPOSTAZIONE
10
9
8
7
6
5
4
3
2
1
700
800
900
1000
1100
(V)
Vp-p
400
500
600
100
200
300
IMPOSTAZIONE
SETTING
REGLAGE
10
9
8
7
6
5
4
3
2
1
1300
1500
1400
(V)
Vp-p
1200
1100
1000
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
200
100
400
300
600
500
800
700
900
10
9
8
7
6
5
4
3
2
1
2000
(V)
Vp-p
SETTING
REGLAGE
IMPOSTAZIONE
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
300
500
400
700
600
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
200
100
IMPOSTAZIONE
SETTING
REGLAGE
10
9
8
7
6
5
4
3
2
1
30
20
50
40
60
RMS
W
Ω)
(@ 500
80
70
90
CUT Pos. "10"
RMS
W
70
80
90
MONOPOLARE
TAGLIO PURO
50
60
MONOPOLAR
PURE CUT
40
MONOPOLAIRE
SECTION PURE
10
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
CUT Pos. "5"
20
30
500
400
300
200
100
10
RMS
W
Ω)
(@ 500
90
90
RMS
W
60
70
80
BLEND Pos."10"
80
70
60
MONOPOLARE
MONOPOLAR
TAGLIO BLEND
50
50
BLEND CUT
301020
40
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
BLEND Pos."5"
30
20
40
MONOPOLAIRE
SECTION AVEC
COAGULATION
500
400
300
200
100
10
RMS
W
RMS
W
90
Ω)
(@ 500
907080
80
70
60
COAG Pos."10"
60
MONOPOLARE
COAGULAZIONE
50
50
MONOPOLAR
COAGULATION
30
20
COAG Pos."5"
301020
MONOPOLAIRE
10
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
40
40
COAGULATION
MN SU-MPC ING March 2008 Page 8 of 9
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
200
100
300
500
400
700
600
900
1300
1200
1500
1400
(V)
Vp-p
800
1100
1000
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
500
(V)
Vp-p
300
400
100
200
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
IMPOSTAZIONE
REGLAGE
SETTING
10
9
8
7
6
5
4
3
2
1
30
20
60
50
40
Ω)
RMS
(@ 200
W
COAG MICRO Pos."10"
RMS
70
W
50
60
MICRO
MONOPOLARE
COAGULAZIONE
301020
40
MONOPOLAR
MICRO
COAGULATION
10
Ω
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
COAG MICRO Pos."5"
MICRO
MONOPOLAIRE
COAGULATION
500
400
300
200
100
60
50
Ω)
RMS
(@ 100
W
RMS
50
60
W
BIPOLARE
COAGULAZIONE
20
40
30
10
Ω
1000
900
800
700
600
500
400
BIPOLAR Pos."10"
20
30
40
BIPOLAR
COAGULATION
COAGULATION
300
BIPOLAR Pos."5"
200
100
50
10
10
BIPOLAIRE
MN SU-MPC ING March 2008 Page 9 of 9
Loading...