Alpha Networks WUSND12B user manual

USB WiFi Adapter for Blu-ray DiscTM/DVD Player

WUS-ND12B

OWNER’S MANUAL

For USA

Before Use

Precautions for use

• Keep this product and this accessory out of the
reach of children.

• This product is for use with the Unique 1.0 m /

3.281 ft extension cable only.

• Do not place this product in a location near
a heat source, or a place subject to direct
sunlight. Doing so may cause a distortion or
malfunction.

• Keep this product away from fl ammable
objects or naked fl ame sources (such as
lighted candles).

• Do not repair this product by yourself. Refer
servicing to qualifi ed personnel only.

Introduction

This product is the wireless adapter with a USB
connector. It is for use with Blu-ray DiscTM Player
only. You can use this product by connecting it to
the USB port of a system.

USA-Federal Communications Commission Statement

FCC Compliance Statement

This device complies with Part 15 of the FCC
Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.

Interference: This equipment has been tested
and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver
is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Wireless Radio

For product available in the USA and Canada
market, only channel 1–11 can be operated.
Selection of other channels is not possible.
The device could automatically discontinue
transmission in case of absence of information
to transmit, or operational failure. Note that this
is not intended to prohibit transmission of control
or signaling information or the use of repetitive
codes where required by the technology.

Configuring a wireless Internet connection

Standards Compliance

• Compatible with IEEE 802.11a/b/g and

802.11n.

Note

• The location where the transmission is most
effective differs depending on the usage
environment. In this case, use the Unique 1.0
m / 3.281 ft extension cable.

• Check precautions and instructions about the
usage location of the product. For details, refer
to the operating instructions of each product.

Accessories

• USB Wireless LAN Adapter (1)

• Unique 1.0 m / 3.281 ft extension cable (1)

• Operating Instructions (this manual) (1)

If this device is going to be operated in 5.15–

5.25GHz frequency range, then it is restricted in

indoor environment only.

Important: Any changes or modifi cations not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.

This device and its antenna (s) must not be co­located or operating in conjunction with any other
antenna or transmitter.

FCC Radiation Exposure Statement: This
equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
This equipment should be installed and operated
with minimum distance 20 cm between the
radiator & your body.

Specifications

Standards Compliance:
IEEE 802.11a/b/g/n
Host Interface:
USB 2.0
Authentication Mode:
WPAPSK, WPA2PSK
Encryption Type:
WEP, TKIP, AES
Frequency and Channel*1:

2.412 GHz – 2.462 GHz [CH1 – 11]

5.15 GHz – 5.25 GHz [CH36 – 48]

5.25 GHz – 5.35 GHz [CH52 – 64]

5.47 GHz – 5.725 GHz [CH100 – 140]

5.725 GHz – 5.85 GHz [CH149 – 165]

Power Consumption:

2.2 W

Mass (Approx.):
USB Wireless LAN Adapter: 15 g
Dimensions (Approx.) (w × h × d):
USB Wireless LAN Adapter:

73.3 mm × 26.6 mm × 10.5 mm

Design and specifications are subject to
change without notice.
*1 The frequency and channel differ depending

on the area.

Wireless Setting

If no Ethernet cable is connected to the ETHERNET jack of your player, you can connect this USB
WiFi adapter to your player and then select “Interface -> Wireless” in the Network setting menu and the
following screen appears:

Wireless setting

Scan
Manual
Auto

1. Scan mode (select the Wireless Network which you scanned)

1) Press / to select Scan, then press OK. A list of existing wireless networks near the Blu-ray
DiscTM player will appear (It may take several seconds for this list to be created). For example:

2) Press

a. If the Blu-ray DiscTM player is connected to an Unencrypted Wireless Network, it will

If the wireless network is functioning, a message “Connection success and IP is obtained” will

3) Press OK to close the message. The Blu-ray

Note:

• If you do not see this message, the Blu-ray Disc

/ to select the desired wireless network, and press OK to confirm.

display "NONE" in the Security list and there is NO need to enter the password.

appear on the TV.

now on, when you turn on the player, it will automatically connect to the network; there is no need
to repeat these steps again.

TM

disc player is now connected to the network. From

TM

player was not able to connect to the network.

b. If the Blu-ray DiscTM player is connected to an Encrypted Wireless Network, a menu

similar to the following will appear:

3) Press OK to activate the on-screen keyboard. Carefully enter the network password by using the

, , / to highlight the desired letter on the keyboard, and then press OK. (If you make a
mistake, use , , / to highlight Back on the keyboard and press OK to erase the mistake.
Or highlight Clear on the keyboard and press OK to clear them, them enter again.)

4) Use

If the wireless network is functioning, a message “Connection success and IP is obtained” will

5) Press OK to close the message. The Blu-ray

From now on, when you turn on the player, it will automatically connect to the network; there is no

Notes:

• If you do not see this message, the Blu-ray Disc

• If the wireless network is encrypted using an unsupported encryption, you cannot connect to the

, , / to highlight Enter on the keyboard, and then press OK.

appear on the TV.

need to repeat these steps again.

network. You must change the router’s encryption type before proceeding.

TM

disc player is now connected to the network.

TM

player was not able to connect to the network.

2. Manual mode (connection to the Wireless Network via your input SSID)

1) Press / to select Auto, then press OK.

The following screen appears.

This section describes how to configure the Blu-ray DiscTM player for accessing the Internet via a WiFi
connection. The procedure for connecting to a wireless network depends on various network arameters.
Read the following configuration methods to determine which instructions to use to onnect to your
network.

LED Indicator

LED Behavior

Inactive Turned Off

LED indicator

Active Keep blinking

2) Press OK to activate the on-screen keyboard and enter the SSID your desired.

3) Use

4) Follow the instructions to continue operating the connection.

, , / to highlight Enter on the keyboard, and then press OK.

3. Auto (connection to the Wireless Networks Using WPS <Wi-Fi Protected Setup>)

1) Press / to select Auto, then press OK.

2) Use

3) Follow the instructions to continue operating the connection.

/ to select PBC or PIN.

Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts
de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire
de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.

Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful

interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall

comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall comply with the e.i.r.p.

limits specified for point-to-point and non point-to-point operation as appropriate.

(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of

the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or
damage to LE-LAN devices.

Avertissement:

Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les
restrictions susmentionnées, notamment :

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à

l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux;

(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5 350 MHz et 5470-5725

MHz doit se conformer à la limite de p.i.r.e.;

(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5 850 MHz) doit se conformer

à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.