Alpha Networks WMP-D16 Inastallation guide

Installation Guide

For WMP-D16

IEEE 802.11b/g MiniPCI Card

DGT 警語 :

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自

變更頻率、加大功率或變更原設計之特性及功能。

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象
時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法
規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用

電波輻射性電機設備之干擾。

本模組於取得認證後將依規定於模組本體標示審驗合格標籤，並要求平台上標示

「本產品內含射頻模組：ID 編號」

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. We declare this product is limited in CH1-CH11 for 2.4G
band by specific firmware controlled by the manufacturer and is not user

changeable.

This device is intended only for OEM integrators under the following
condition-

1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and

2) The transmitter module may not be co-located with any other transmitter or
antenna.

3) For all products market in US, OEM has to limit the operation channels in CH1
to CH11 for 2.4G band by supplied firmware programming tool. And OEM shall
not supply any tool or info to the end-user regarding to change the domain selection.
As long as 3 conditions above are met, further transmitter test will not be
required.However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),

then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may
be installed such that 20 cm may be maintained between the antenna and users (for
example: Access point, Wireless Router, Notebook, etc.). The final end product
must be labeled in a visible area with the following: “Contains TX FCC ID:
RRK2005090049-1”.

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the users manual of
the end product which integrate this module.

The users manual for OEM integrators must include the following information
in a prominent location “
IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or transmitter.
We declare this product is limited in CH1-CH11 for 2.4G band by specific
firmware controlled by the manufacturer and is not user changeable.

If the end product integrating this module is going to be operated in 5.15 ~

5.25GHz frequency range, the following warning statement must be included
in the user manual.

The 5.15 ~ 5.25GHz frequency band in US/Canada is restricted to indoor use only.

Industry Canada Statement

Operation is subject to the following two conditions:

1) this device may not cause interference and

2) this device must accept any interference, including interference
that may cause undesired operation of the device

This device has been designed to operate with an antenna having
a maximum gain of 4.5 dBi.

Antenna having a higher gain is strictly prohibited per regulations
of Industry Canada. The required antenna
impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the EIRP is not more
than required for successful communication.

IMPORTANT NOTE: IC Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for
uncontrolled environments. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.