Alphacool Eisschicht 14 W-mK User Manual

Alphacool Eisschicht 14 W/mK

Features

Highly Conformable and High Heat Conducting Gel Materials.

Eisschicht Thermal Gap Filler Pads are highly conformable and high heat conducting gel materials in a versatile sheet form.

They easily t and adhere to most all shapes and sizes of components, including protrusions and recessed areas.

Constructions

Series Chracteristics Constructions

Silicone compound with double sticky

Alphacool Eisschicht 14 W/mK

Alphacool Eisschicht 14 W/mK -

0.5mm

surfaces and Thermal Conductivity of
XR-j material is 14.0W/m-K by using
GHP (9.0W/m-K by using Hot Disk)

Silicone compound as above XR-j plus
additional hardening of the top surfa­ce to facilitate handling and installati­on during complex assemblies

Recommended Application

In areas where space between sur­face is uneven or varies and where
surface textures are a concern re-

garding efcient thermal transfer, the

supple consistency of Gap Filler Pad
is excellent for lling air gaps and un­even surfaces.

Plain Type

Hardened
Surface

Alphacool International GmbH
Marienberger Str. 1
38122 Braunschweig

Telefon: [phone] - 0
Fax: [phone] - 22
e-Mail: [e-mail]

Water

Heat Sink

PCB

Thermal Gap Filler Pad

Thermal Resistance

Compression Force 0.5mmT 1.0mmT 1.5mmT

100kPa (14.5psi) 0.8 (0.12) 1.1 (0.17) 1.6 (0.25)

300kPa (43.5psi) 0.7 (0.10) 1.0 (0.16) 1.5 (0.23)

500kPa (72.5psi) 0.6 (0.09) 1.0 (0.15) 1.3 (0.19)

Unit: K-cm2/W (K-in2/W)

1

Alphacool Eisschicht 14 W/mK

Typical Properties

Properties unit XR-m Test method

Color - Light Gray Visual

Specic Gravity - 3.2 ASTM D 792

Physical
Properties

Electrical
Properties

Thermal
Properties

Hardness

Highest Value

Tensile Strength MPa (psi) 0.2 (29.0) ASTM D 412

Elongation % 25 ASTM D 412

Tear Strength N/mm (ppi) 1.0 (5.7) ASTM D 624

Volume Resistivity Ohm-m 1.0x10

Breakdown Voltage kV/mm (volts/mil) 18 (457) ASTM D 149

Dielectric Strength kV/mm (volts/mil) 13 (330) ASTM D 149

Dielectric Constant -

Dissipation Factor -

Thermal Conductivity W/m-K

Useful Temperature °C (°F) -40 to +150 (-40 to +302) -

Low molecular

Siloxane

Flame Retardant UL94 V-0 UL94

Shore OO

(ASKER C)

wt%

50Hz 6.8

1MHz 6.8

50Hz 0.06

1MHz 0.001

9.0 by Hot Disk ISO/CD 22007-2

to D20

D

4

Total

80

(57)

11

14.0 by GHP ASTM D 5470

0.0020
or less

ASTM D2240

(ISO 7619)

ASTM D257

ASTM D 1501kHz 6.8

ASTM D 1501kHz 0.001

Gas

Chromotography

Alphacool International GmbH
Marienberger Str. 1
38122 Braunschweig

Telefon: [phone] - 0
Fax: [phone] - 22
e-Mail: [e-mail]

Compression Force

Compression Ratio 0.5mmT 1.0mmT 1.5mmT

10% 110 (24.9) 89 (20.2) 96 (21.8)

20% 335 (76.0) 206 (46.7) 248 (56.2)

30% 592 (134.2) 453 (102.6) 505 (114.4)

40% 849 (192.3) 714 (161.8) 825 (186.9)

50% 1091 (274.1) 1095 (248.1) 1213 (274.8)

Sustain 50% 898 (203.4) 897 (203.2) 945 (214.1)

Unit: N/6.4cm2 (psi)

2

Alphacool Eisschicht 14 W/mK

Durability

Test Property Unit

Specic Gravity - 3.2 3.2 3.2 3.2

Hardness ASKER C 50 64 50 85

Breakdown Voltage kV/mm 18 19 18 19

Thermal conductivity W/m-K 14 14 14 14

Test Property Unit

Specic Gravity - 3.2 3.2

Hardness ASKER C 50 62

Breakdown Voltage kV/mm 18 17

Thermal conductivity W/m-K 14 14

- Specimen: XR-j

Initial After 1,000hrs Initial After 1,000hrs

Initial After 1,000hrs

70°C 150°C

60°C / 90%RH

reduced tempereature

-40°C = -40°F

60°C = 140°F

70°C = 158°F

125°C = 227°F

150°C = 302°F

Types and Congurations

Series Product Name Thickness Sheet Size

Alphacool Eisschicht

14W/mK

(Sarcon XR-Hj)

Alphacool Eisschicht

14W/mK

(Sarcon XR-j)

14W/mK (Sarcon XR-Hj) 0.5mm ± 0.15

1.0mm ± 0.20

14W/mK (Sarcon XR-j)

1.5mm ± 0.20

100x100x0,5mm

2x 120x20x0,5mm

100x100x1mm

2x 120x20x1mm

100x100x1,5mm

2x 120x20x1,5mm

Alphacool International GmbH
Marienberger Str. 1
38122 Braunschweig

Telefon: [phone] - 0
Fax: [phone] - 22
e-Mail: [e-mail]

Handling notes

• It is recommended to use the material in up to 30% of compression ratio. Using the material beyond the recommen­ded compression rate may result in excessive silicone oil exudation.

• It is recommended to compress the material with the equal ratio on the whole surface. Partial excessive stress may
also result in excessive silicone oil exudation.

Warranty Statement

• Properties of the products may be revised due to some changes for improving performance.

• Properties values in this document are not specication or guaranteed.

• This product is made of silicone, and silicone oil may exude from the product.

• This product is made of silicone, and low molecular siloxane may vaporize depending on operating conditions.

• The product is designed, developed, and manufactured for general industrial use only. Never use for medical, surgical,

and/or relating purposes. Never use for the purpose of implantation and/or other purposes by which a part of or
whole product remains in human body.

• Beforeusing,asafetymustbeevaluatedandveriedbythepurchaser.

• Contents described in the document do not guarantee the performances and qualities required for the purchaser‘s
specic purposes. The purchaser is responsible for pre-testing the product under the purchaser‘s specic conditions

and for verifying the expected performances.

• Statements concerning possible or suggested uses made herein may not be relied upon, or be constructed, as a

guaranty of no patent infringement.

3