Alphacool Eisbaer Refill-Kit User Manual

Version: 10.07.2020

We assume no responsibility for any typing errors.

Alphacool International GmbH, Marienberger Strasse 1, 38122 Braunschweig Tel: [phone] Supportmail: [e-mail]

What is this?

Alphacool Eisbaer Refill-Kit

Highlights

A kit for making the filling of the Eisbaer AiO CPU water cooling systems easier and safer. It consists of a

funnel with G1/4" thread, a syringe of thermal paste and a SATA to 3-pin adapter cable It also includes an
ATX jumper plug so that the power supply can be started independently.

- Screw-on funnel with G1/4" thread

- High End Heat Conducting Paste

- SATA on 3-pin pump connector

Version: 10.07.2020

We assume no responsibility for any typing errors.

Alphacool International GmbH, Marienberger Strasse 1, 38122 Braunschweig Tel: [phone] Supportmail: [e-mail]

Technical datas funnel

Height x Diameter 55 x 60 mm

Net weight 20 g

Max working temperatur 60 °C

Material fitting brass

Material funnel rubber

Thread 1x G1/4“

Scope of delivery

1x ATX jumper plug

1x funnel with G1/4" screw-on thread

1x SATA on 3-pin pump connector

1x syringe with thermal grease

Product pics download http://alphacool.com/download/Alphacool_Eisbaer_Refill_Kit.zip

Technical datas ATX connector

L x W x H 24 x 12 x 60 mm

Net weight 5 g

Max working temperature 60 °C

Material ATX connector plastic

Connection 24-Pin ATX

Technical datas

Sata to 3-pin adapter

Cable length 20 cm

Net weight 9 g

Connector A SATA power connection

Connector B 3-pin fan connection

Version: 10.07.2020

We assume no responsibility for any typing errors.

Alphacool International GmbH, Marienberger Strasse 1, 38122 Braunschweig Tel: [phone] Supportmail: [e-mail]

Article text

Alphacool is an internationally renowned company in the field of watercooling solutions for both industrial and end
customer. Constantly innovating and improving both server and home solutions, Alphacool strives to create the
perfect solution.

Everything you need to fill your Eisbaer

The refill kit contains all of the important tools you need to fill your Eisbaer CPU water cooling system with a few

simple steps. This includes a funnel with G1/4" thread, a high-quality thermal paste in a syringe, an adapter cable for
the pump and an ATX jumper plug.

Easy to use

Remove the Eisbaer from your ensuring your power supply is turned off. Unplug the 24-pin ATX connector from
the mainboard and fit the ATX jumper plug to it. Place the radiator on a table and the Eisbaer CPU/pump/
Reservoir unit on a slightly elevated surface. Then simply mount the funnel on the fillport. With the SATA to 3-pin
adapter cable you can now connect the pump of the Eisbaer to your power supply. Now slowly fill the Eisbaer with
your liquid until the reservoir is full. Now you can switch on the power supply again. The ATX bridging plug starts
the power supply unit and the pump of the Eisbaer starts to work. It is important that you turn off the pump occa­sionally to refill with liquid. The pump must never run dry.

When the Eisbaer is full, you can plug the fillport again. Then let the Eisbaer run a little outside your case, while you

shake the Eisbaer in all directions. Ideally, always hold the radiator lower than the Eisbaer CPU/pump/Reservoir
unit unit so that the air can move upwards into the reservoir. You will notice that you may need to top up some
liquid. The reservoir should be approximately 90% full at the end of the procedure.

Other datas

Article number Alphacool 11687

EAN Code 4250197116879

PU 1

Dimensions PU BxTxH / 20 x 16 x ca. 30 mm

Weight 46 g

Customs code 84733080000