Alpha UPE-3, UPE-6, UPE-M3, UPE-M6, PN Installation
...
Round Security Bar
Field Installation Manual
UPE-3, UPE-6, UPE-M3, UPE-M6, PN, CE and FPE Series,Enclosures
Effective: October, 2013
Safety Notes
Review the drawings and illustrations contained in this document before proceeding. If there are any questions regarding
the safe installation or operation of the system, contact Alpha Technologies or the nearest Alpha representative. Save this
document for future reference.
To reduce the risk of injury or death and to ensure the continued safe operation of this product, the following symbols have
been placed throughout this manual. Where these symbols appear, use extra care and attention.
WARNING! ELECTRICAL HAZARD
ELECTRICAL HAZARD WARNING provides electrical safety information to PREVENT
INJURY OR DEATH to the technician or user.
WARNING! FUMES HAZARD
FUMES HAZARD WARNING provides fumes safety information to PREVENT INJURY OR
DEATH to the technician or user.
WARNING! FIRE HAZARD
FIRE HAZARD WARNING provides ammability safety information to PREVENT INJURY OR
DEATH to the technician or user.
There may be multiple warnings associated with the call out. Example:
WARNING! ELECTRICAL & FIRE HAZARD
This WARNING provides safety information for both Electrical AND Fire Hazards
CAUTION!
CAUTION provides safety information intended to PREVENT DAMAGE to material or equipment.
NOTE:
NOTE provides additional information to help complete a specic task or procedure.
ATTENTION:
ATTENTION provides specic regulatory/code requirements that may affect the placement of equipment and /or
installation procedures.
The following sections contain important safety information that must be followed during the installation and maintenance
of the equipment and batteries. Read all of the instructions before installing or operating the equipment, and save this
manual for future reference.
Round Security Bar Field Installation Manual
UPE-3, UPE-6, UPE-M3, UPE-M6, PN, CE and FPE Series Enclosures
745-847-C1-001, Rev. B
Effective Date: October, 2013
Copyright 2013
Alpha Technologies, Inc.
member of The Group
NOTE:
Photographs contained in this manual are for illustrative purposes only. These photographs may not match
this installation.
NOTE:
Operator is cautioned to review the drawings and illustrations contained in this manual before proceeding. If
there are questions regarding the safe operation of this powering system, please contact Alpha Technologies
or the nearest Alpha representative.
NOTE:
Alpha shall not be held liable for any damage or injury involving its enclosures, power supplies, generators,
batteries, or other hardware if used or operated in any manner or subject to any condition not consistent with
its intended purpose, or is installed or operated in an unapproved manner, or improperly maintained.
TM
Contacting Alpha Technologies: www.alpha.com
For general product information and customer service (7 AM to 5 PM, Pacic Time), call
7 AM to 5 PM, Pacic Time or 24/7 emergency support
745-847-C1-001 Rev. B (10/2013)
or
1-800-863-3930
For complete technical support, call
1-800-863-3364
3
Table of Contents
Safety Notes ....................................................................................................................................................... 5
1.0 Introduction ............................................................................................................................................... 6
1.1 Parts List ......................................................................................................................................... 6
1.2 Required Tools ................................................................................................................................ 6
2.0 Installation ................................................................................................................................................. 7
2.1 Dimensioned Enclosure Drawings .................................................................................................. 9
2.1.1 CE-3G ....................................................................................................................................... 9
2.1.2 CE-3X2 ................................................................................................................................... 10
2.1.3 CE-9G ......................................................................................................................................11
2.1.4 CE-9X2 ................................................................................................................................... 12
2.1.5 PN-3 ....................................................................................................................................... 13
2.1.6 PN-4 ....................................................................................................................................... 14
2.1.7 UPE-3 ..................................................................................................................................... 15
2.1.8 UPE-M3 .................................................................................................................................. 16
2.1.9 UPE-6 ..................................................................................................................................... 17
2.1.10 UPE-M6 .................................................................................................................................. 18
2.1.11 FPE ......................................................................................................................................... 19
Figures and Tables
Fig. 1-1 Security Lock Dimensions ............................................................................................................... 6
Fig. 2-1 Marking Guide Lines ...................................................................................................................... 7
Fig. 2-2 Drill Holes ....................................................................................................................................... 7
Fig. 2-3 Side Bracket Assembly ................................................................................................................... 8
Fig. 2-4 Lock Bracket Assembly ................................................................................................................... 8
Fig. 2-5 Installation of the Lock Shroud on the Security Bar ........................................................................ 8
Fig. 2-6 CE-3G Enclosure Hole Locations ................................................................................................... 9
Fig. 2-7 CE-3X2 Enclosure Hole Locations ............................................................................................... 10
Fig. 2-8 CE-9G Enclosure Hole Locations ..................................................................................................11
Fig. 2-9 CE-9X2 Enclosure Hole Locations ................................................................................................ 12
Fig. 2-10 PN-3 Enclosure Hole Locations .................................................................................................... 13
Fig. 2-11 PN-4 Enclosure Hole Locations .................................................................................................... 14
Fig. 2-12 UPE-3 Enclosure Hole Locations .................................................................................................. 15
Fig. 2-13 UPE-M3 Enclosure Hole Locations .............................................................................................. 16
Fig. 2-14 UPE-6 Enclosure Hole Locations ................................................................................................. 17
Fig. 2-15 UPE-M6 Enclosure Hole Locations .............................................................................................. 18
Fig. 2-16 FPE Enclosure Dimple Locations ................................................................................................. 19
Table 1-1 Enclosure Part List and Component Descriptions .......................................................................... 6
Table 1-2 Installation Tools .............................................................................................................................. 6
4
745-847-C1-001 Rev. B (10/2013)
Round Security Bar Safety Notes
Review the drawings and illustrations contained in this manual before proceeding. If there are any questions regarding the
safe installation or operation of this product, contact Alpha Technologies or the nearest Alpha representative. Save this
document for future reference.
To reduce the risk of injury or death, and to ensure the continued safe operation of this product, the following symbols
have been placed throughout this manual. Where these symbols appear, use extra care and attention.
WARNING! ELECTRICAL HAZARD
Electrical shock can KILL. Disconnect and remove or protect all electrical equipment within
the enclosure before drilling into the enclosure.
WARNING! FIRE HAZARD
CE Model Enclosures have integrated gas lines near the enclosure door jam. Turn off the gas
before installing the enclosure and ensure all drilling locations will not damage the gas lines
before proceeding.
CAUTION!
Drilling swarf can cause laceration and puncture wounds to eyes and skin. NEVER remove drilling swarf
with bare hands. Always wear safety glasses and gloves, and use a vacuum cleaner or brush to remove
swarf from within the enclosure.
745-847-C1-001 Rev. B (10/2013)
5
1.0 Introduction
B
A
C
Each security bar kit contains the parts and accessories needed to secure one enclosure door. If the enclosure
has both a front and back door, it will require two kits, with exception of the FPE.
1.1 Parts List
Enclosure Color Alpha Part Number
UPE
PN
CE
FPE
Seafoam Green 745-847-20
Gray 745-847-21
Seafoam Green 745-847-20
Gray 745-847-21
Seafoam Green 745-847-20
Gray 745-847-21
Seafoam Green 745-847-22
Gray 745-847-23
Pine Green 745-847-24
White 745-847-25
Table 1-1, Enclosure Part List and Component Descriptions
1.2 Required Tools
Installation tools:
Tape measure
Masking tape
1/2" drive hand drill
Center punch
7/16" socket and socket wrench
Size "K" (9/32") drill bit
4 foot level
Pencil
Utility knife
Vacuum to remove metal shavings from enclosure interior
# of Required
Kits
1
2
2
1
Kit Components Description (Qty)
• Lock Bracket (2)
• Side Bracket (4)
• Security Bar (2)
• Lock Guard (2)
• Carriage Bolt 1/4"-20X3/4" (12)
• Lock Washer 1/4" (12)
• Flat Washer 1/4" (12)
• Hex Nut 1/4"-20 (12)
• Lock Bracket (4)
• Side Bracket (8)
• Security Bar (4)
• Lock Guard (4)
• Carriage Bolt 1/4"-20X3/4" (24)
• Lock Washer 1/4" (24)
• Flat Washer 1/4" (24)
• Hex Nut 1/4"-20 (24)
Table 1-2, Installation Tools
In addition:
To secure the enclosure, each bar requires a
security lock. Each user-supplied lock must meet
the following dimensions:
Where:
A = 5/16"
B = 3/4"
C = 2 1/2"
Fig. 1-1, Security Lock Dimensions
6
745-847-C1-001 Rev. B (10/2013)
Loading...