Almost Heaven Saunas KIP-30-W1/FIN-30, KIP-45-W1/FIN-45, KIP-30-W3/FIN-30-3, KIP-45-B1/FLB-45, KIP-45-W3/FIN-45-3 Owner's/operator's Manual
...
14112012
MODEL MODEL MODEL
KIP-30-B1/FLB-30 KIP-30-W1/FIN-30 KIP-30-W3/FIN-30-3
KIP-45-B1/FLB-45 KIP-45-W1/FIN-45 KIP-45-W3/FIN-45-3
KIP-60-B1/FLB-60 KIP-60-W1/FIN-60 KIP-60-W3/FIN-60-3
KIP-80-B1/FLB-80 KIP-80-W1/FIN-80 KIP-80-W3/FIN-80-3
KIP-30-B3/FLB-30-3
KIP-45-B3/FLB-45-3
KIP-60-B3/FLB-60-3
KIP-80-B3/FLB-80-3
CONTROLS CONTACTORS
F-1T FL-402
F-2T FL-303
F-2
Owner’s/Operator’s Manual
Sauna heater installation, wiring, operating instructions, trouble shooting, maintenance
and guarantee.
IMPORTANT! This manual must be left with owner, manager
or operator of Sauna after it is used by electrician!
Importer:
Almost Heaven Saunas
HC66, 465-A
Highway 219 North
Renick, West Virginia 24966
304-497-3991
2
3
THE SAUNA ROOM SHALL BE PROVIDED WITH PROPER VENTILATION
INSTALLATION OF WALL MODEL HEATER,
CONTROL, CONTACTOR
1. Remove heater from carton and attach heater
to wall with screws are supplied. If wall thickness
is less than 3/4”, use 2”x 4” backing behind heater.
Observe proper clearances as per page 4 and table 1.
2. See applicable wiring diagram g. 5–8 for
heater model. Heater must be permanently installed
(no pigtails or plug allowed) and wiring must be
done by a licensed electrician, who must follow
wiring diagram provided and adhere to local codes.
Use proper A.W.G. rated wire size and use copper
wire suitable for 90°C within Sauna walls. Use
grounding terminals provided in Sauna heater,
control system, and contactor to properly ground
the equipment as per NEC and local codes.
3. See g. 5–8 to match control to heater model.
Locate control in wall, 5’ up from oor, so that
panel faces outward from room. Punch out one of
knockouts in roughin box and push rubber grommet
(provided) into knockout hole. Bring capillary tubing
with sensing bulb out through grommet and through
stud wall, so that capillary bulb is located 6’’ from
ceiling inside Sauna room and as close to Sauna
heater as possible, taking care to avoid sharp bends
in tubing (to prevent damage to tubing and liquid
within). Extra tubing can be coiled up inside wall.
Nail or screw bulb guard to wall to secure sensing
bulb.
4. Install contactor 4’’ up from oor behind Sauna
heater, on outside wall of Sauna room. Wire from
contactor to heater must be within seal tight
exible conduit. (Contactor may also be located in
an equip. room or closet, but must be accessible,
for servicing.
5. Inside the heater box there are two signs. Please
place the metal ”CAUTION” sign on the interior
wall of the Sauna room directly above the heater
in a visible place. Place the metal ”WARNING”
sign outside, on the door of the Sauna room.
”MAINTENANCE INSTRUCTIONS” are at the end
of this manual.
Figure 1.
4
Figure 2.
Figure 3.
Figure 3a.
Figure 4.
THE SAUNA ROOM SHALL BE PROVIDED WITH PROPER VENTILATION WALL-MOUNTED
HEATERS-MINIMUM CLEARANCES, MIN-MAX SPACE, ADEQUATE VENTILATION
MODEL INPUT
kW
MIN.
HEIGHT
FLOOR AREA SAUNA
ROOM
MIN. SPACING FROM ADJACENT
SURFACES, INCHES
Min.
Sq.Ft
Max.
Sq.Ft
Min.
Cu.Ft
Max.
Cu.Ft
KIP-30-B/W
FLB/FIN-30
3.0 6’ 2” 10 20 84 130 3”
KIP-45-B/W
FLB/FIN-45
4.5 6’ 2” 16 30 100 210 3”
KIP-60-B/W
FLB/FIN-60
6.0 6’ 2” 28 40 170 300 4”
KIP-80-B/W
FLB/FIN-80
8.0 6’ 2” 40 65 250 425 5”
Table 1.
5
Figure 5.
SAUNA HEATER (240 V) WITH BUILT IN CONTROLS
Model kW Amps Voltage Phase Wire size
KIP-30-B1
FLB-30
3.0 12.5 240 1 12
KIP-45-B1
FLB-45
4.5 18.8 240 1 10
KIP-60-B1
FLB-60
6.0 25.0 240 1 10
KIP-80-B1
FLB-80
8.0 33.3 240 1 8
SAUNA HEATER (208 V) WITH BUILT IN CONTROLS
Model kW Amps Voltage Phase Wire size
KIP-30-B3
FLB-30-3
3.0 8.3 208 3 14
KIP-45-B3
FLB-45-3
4.5 12.5 208 3 14
KIP-60-B3
FLB-60-3
6.0 16.7 208 3 12
KIP-80-B3
FLB-80-3
8.0 22.2 208 3 10
1 2
3
1 2 3
KIP-30-B1 / KIP-45-B1 / KIP-60-B1 / KIP-80-B1
FLB-30 / FLB-45 / FLB-60 / FLB-80
240 V 1 PHASE HEATER
HEATING
ELEMENTS
TIMER
CONTACTOR THERMOSTAT
LIMIT CONTROL
LINE 1
LINE 2 GND
GROUND
Internal wiring only
1 2
3
1 2 3
KIP-30-B3 / KIP-45-B3 / KIP-60-B3 / KIP-80-B3
FLB-30-3 / FLB-45-3 / FLB-60-3 / FLB-80-3
208 V 3 PHASE HEATER
HEATING
ELEMENTS
TIMER
CONTACTOR THERMOSTAT
LIMIT CONTROL
Internal wiring only
LINE 1 LINE 3
LINE 2 GND
GROUND
6
Figure 5a.
SAUNA HEATER WIRING AND HOOKUP
Important! Before hooking up electrical wires to
junction box of heater, remove capillary tubing and
bulb from junction box and bring up wall to left
or right side of heater. Cover tubing with wooden
molding provided, coil up excess tubing, and place
under heater close to floor.
Refer to chart page 4 for proper wire size and
amperage. See page 3 for required clearances. Any
wiring within internal Sauna walls must be rated
90º C and copper wire must be used. Run wire
through seal tight ex conduit from wall to heater
and connect to junction box at back of heater with
90º connector. Connect to terminals 1 and 2 and
connect ground wire to lug marked ground. (Cover
plate under heater must be removed rst.)
Note! If connection to heater will be made at a later
time, bring flex into Sauna room 4–6” from floor,
and leave 3’ of flex for hookup (can be cut to right
length later).
Before testing heater, ll rock cavity with igneous
stones provided with heater and fasten metal rock
guard at top of heater. (See general info concerning
washing and placing of stones.)
Be sure to cover thermostat bulb with protective metal cover by threading bulb through holes in
cover, and fasten bulb cover to wall with screws
provided. Also, take care when nailing protective
wood strips over capillary tubing, so that nails do
not puncture tubing. If punctured, entire thermostat
must be replaced.
7
Figure 6. Use this diagram for wiring and hookup
Figure 6a.
SAUNA HEATER (240 V) WITH WALL CONTROL
Model kW Amps Voltage Phase Wire size Control Contactor
KIP-30-W1, FIN-30 3.0 12.5 240 1 12 F-1T None
KIP-45-W1, FIN-45 4.5 18.8 240 1 10 F-1T None
KIP-60-W1, FIN-60 6.0 25.0 240 1 10 F-1T None
SAUNA HEATER WIRING AND HOOKUP –
ALSO REFER TO FIGURE 1
Refer to chart above for proper wire size and
amperage. See page 3 for required clearances.
Use copper wire from breaker to wall-mounted
control, which should face outward from Sauna,
5’ from oor to center of box. Note! Neutral wire
must also be brought to control to provide power
for light switch. (Circuit breaker is built into control
to provide protection for light.) From control to
heater, provide seal tight ex conduit for wire,
and connect to junction box at back of heater with
90º connector. Connect to terminals 1 and 2 and
connect ground wire to lug marked ground. (Cover
plate under heater must be removed rst.)
Note! If connection to heater will be made at a later
time, bring flex into Sauna room 4–6” from floor,
and leave 3’ of flex for hookup (can be cut to right
length later).
Before testing heater, ll rock cavity with igneous
stones provided with heater and fasten metal rock
guard at top of heater. (See gen. info concerning
washing and placing of stones.)
1
2
3
CG170-U1
L1 A1 L2 A2
L1 L2
1 2 3 4 5
GND
GND
1 2 3 4 5
F-2T + FL-402
240 V SINGLE PHASE HEATER
KIP-30-W1 / KIP-45-W1 / KIP60-W1 / KIP-80-W1
FIN-30 / FIN-45 / FIN-60 / FIN-80
LIMIT
CONTROL
CONTACTOR
HEATING
ELEMENTS
Internal wiring only
GROUND
GROUND
8
Figure 7. Use this diagram for wiring and hookup
Figure 7a.
SAUNA HEATER WIRING AND HOOKUP –
ALSO REFER TO FIGURE 1
Refer to chart above for proper wire size and
amperage. See page 3 for required clearances.
Use copper wire from breaker to wall-mounted
contactor. Use 90°C copper wire from contactor
to control and from control to room light. Also use
90°C wire from contactor to Sauna heater (within
seal tight ex conduit) and connect to junction box
at back of heater with 90°C connector. Connect to
terminals 1 and 2 and connect ground wire to lug
marked ground. (Cover plate under heater must be
removed rst).
Important! Follow wiring instructions carefully
to prevent shorting of 6 amp circuit breaker in
contactor. Do not force wires against circuit
breaker: be sure there are no bare wires or shorts.
The circuit breaker, has been factory tested, and
if it is shorted out, it will be responsibility of the
electrical contactor to replace it!
Note! If connection to heater will be made at a later
time, bring flex into Sauna room 4–6” from floor,
and leave 3’ of flex for hookup (can be cut to right
length later). Before testing heater, fill rock cavity
with igneous stones provided with heater and
fasten metal rock guard at top of heater. (See gen.
info concerning washing and placing of stones.)
Notice that insulated neutral wire (same A.W.G.
gauge as supply wire) is also brought from breaker
to contactor!
SAUNA HEATER (240 V) WITH WALL CONTROL
Model kW Amps Voltage Phase Wire size Control Contactor
KIP-80-W1
FIN-80
8.0 33.3 240 1 8 F-2T FL-402
1
2
3
CG170-U1
L1 A1 L2 A2
L1 L2
1 2 3 4 5
GND
GND
1 2 3 4 5
F-2T + FL-402
240 V SINGLE PHASE HEATER
KIP-30-W1 / KIP-45-W1 / KIP60-W1 / KIP-80-W1
FIN-30 / FIN-45 / FIN-60 / FIN-80
LIMIT
CONTROL
CONTACTOR
HEATING
ELEMENTS
Internal wiring only
GROUND
GROUND
9
Figure 8. Use this diagram for wiring and hookup
L1 A1 L2 L3A2
L1 L2 L3
1 2 3 4 5
GND
GND
1 2 3 4 5
F-2T+FL-303
CG170-U3
208 V 3 PHASE HEATER
HEATING
ELEMENTS
CONTACTOR
LIMIT
CONTROL
GROUND
GROUND
KIP-30-W3 / KIP-45-W3 / KIP-60-W3 / KIP-80-W3
FIN-30-3 / FIN-45-3 / FIN-60-3 / FIN-80-3
Internal wiring only
Figure 8a.
SAUNA HEATER (208 V) WITH WALL CONTROL
Model kW Amps Voltage Phase Wire size Control Contactor
KIP-30-W3
FIN-30-3
3.0 8.3 208 3 14 F-2T FL-303
KIP-45-W3
FIN-45-3
4.5 12.5 208 3 14 F-2T FL-303
KIP-60-W3
FIN-60-3
6.0 16.7 208 3 12 F-2T FL-303
KIP-80-W3
FIN-80-3
8.0 22.2 208 3 10 F-2T FL-303
SAUNA HEATER WIRING AND HOOKUP –
ALSO REFER TO FIGURE 1
Refer to chart above for proper wire size and
amperage. See page 3 for required clearances. Use
copper wire from breaker to wall-mounted contactor.
Supply cable must have 5 wires including insulated
neutral and separate ground. Use 90°C copper wire
from contactor to control and from control to room
light. Also use 90°C copper wire from contactor to
Sauna heater (within seal tight ex conduit), and
connect to junction box at back of heater, with
90° connector. Connect to terminals 1, 2, 3 and
connect ground wire to lug marked ground. (Cover
plate under of heater must be removed rst).
Important! Follow wiring instructions carefully
to prevent shorting of 6 amp circuit breaker in
contactor. Do not force wires against circuit
breaker: be sure there are no bare wires or shorts.
The circuit breaker, has been factory tested, and if
it is shorted out, it will be the responsibility of the
electrical contactor to reflace it!
If connection to heater will be made at a later
time, bring ex into Sauna room 4–6” from oor,
and leave 3’ of ex for hookup (can be cut to right
length later). Before testing heater, ll rock cavity
with igneous stones provided with heater and fasten metal rock guard at top of heater. (See gen. info
concerning washing and placing of stones.)
10
Figure 9.
F-2 SAUNA CONTROL
This control can be used with any heater and proper
contactor. See chart for contactor model.
This control can be used only with use of a time
clock.
This control can be used only when an attendant
is on duty during hours of operation.
Have a heat control (thermostat) which must be
set between minimum and maximum heating, or
the timer will not cause the Sauna to heat. Put heat
control setting to maximum, heat Sauna for 1/2
to 1 hour to observe adequate Sauna temperature.
If room is too hot, adjust heat control knob back
toward minimum setting, until desired temperature
is reached.
SAUNA TIMERS
Have a 60 min. timer (0 to large 1 on the dial), and
if you wish to use the full 60 min. cycle, turn the
timer knob past the rst 1 to number 2 or 3 on
the dial. Then turn backward to the large 1 until
a click is heard. Leave knob at the setting, and
Sauna will operate for 1 hour before shutting off
automatically.
Allow at least 30 minutes for room to heat up to
an average Sauna temperature. Note!! If you set
timer past rst 1, timer will not come on until the
time set has elapsed. The 60 min. timer is quiet. It
does not tick.
Have an added feature--an 8 hour time clock
(small 1 to 8 on the timer dial). If you wish to preset
your Sauna heater to automatically turn on when
uou are away, you may preset up to 8 hours in
advance of Sauna bathing.
For eg., if you set the timer knob at number 3
setting, the Sauna heater will turn on 3 hours later,
and will be ready for useage in 3 1/2 hours (allowing
for 1/2 hour heat up time). The heater will shut off
automatically in another half hour, and if you wish
to continue using Sauna, reset the 60 min. timer
back up to the large 1.
11
SAUNA – GENERAL INFORMATION
Rock placement – do not operate heater without
stones!
Use only the stones which are supplied with the
Sauna heater. Wash stones with water hose and
place inside of heater box so that rocks are between
and around heating elements. However, do not
force rocks between elements.
Use smaller stones rst, and continue to ll heater
with larger stones until they are about 2” below
rock guard. You may not need all of the stones.
Stones should be placed loosely within heater
so that there is good heat circulation around and
through them. Stones should completely cover the
heating elements, however!
Pouring water over exposed elements could cause
heater damage!
TESTING OF SAUNA HEATER
1. After Sauna heater has been properly wired,
according to appropriate wiring diagram and
local codes, turn Sauna breaker on in the main
breaker panel. (Note! Electrician must label
“Sauna” breaker.)
2. Turn thermostatic (heat) control to on position
(this is located either on your heater or on your
remote wall control. If you have a wall control,
the indicator light will come on to show that
the Sauna is heating). Set timer to 10 or 15
minutes.
3. Within 5 minutes, you should be able to feel
heat from heater elements when holding your
hand over heater.
4. If Sauna does not heat, refer to troubleshooting
information.
5. It is normal for smoke to appear during the rst
heating, as protective element coating needs to
burn off. Turn sauna on for 1 hour before using
the first time, to eliminate smoking.
TROUBLESHOOTING
A. If sauna does not operate after initial installation
and wiring:
1. Check breaker to be sure that it is on. Also,
breaker should be correct size.
2. Make sure that a neutral wire has been
included (necessary for all heaters except
model with built-in control).
3. Check circuit breaker in contactor to be sure
that it has not been shorted out.
4. Be sure that thermostat and timer are both in
on position.
5. Be sure that timer winds down. If timer has
been shorted out, heater will not operate.
B. If sauna has been in operation, but heater
ceases to operate:
1. Check breaker to make sure it is on.
2. Check timer to see if it winds down.
3. Check high limit reset button in heater (reset is
under the heater (wall models) or on the back
of the junction box (oor models)) to see if it
has been released.
4. Call your electrician or service person for
further help.
NOTE! A ground fault interrupter (GFI) should not be
installed in and does not belong in a Sauna. If used,
the breaker will trip, and damage could result.
C. If sauna heater operates, but sauna room does
not come up to sauna temperature (160–185ºF
normal sauna temperature):
1. You must allow at least 30 minutes for Sauna
heat-up time.
2. Is Sauna thermometer located 6” from ceiling,
and is it above or close to Sauna heater?
(This is proper location for Sauna temperature
reading.) Thermometer readings vary with room
heights and location. Eg. 180ºF above Sauna
heater = 165 on opposite wall = 140 on
upper bench level = 120 on lower bench level
= 100 at oor level.
3. Check for proper wire size, amp size, and
proper wiring (according to diagrams and
information) also necessary copper wiring.
4. Check for placement of stones to make sure
they are loosely spaced around elements,
to insure good air ow. Stones packed too
tightly will restrict air ow and reduce heating
capacity.
5. Check for heat loss (around or under door,
around ceiling light or fan – we do not
recommend ceiling light and a fan does not
belong in the Sauna.
6. Is room properly insulated?
7. Is ceiling higher than 7’?
8. After checking all the above, remove rocks
and check heater elements for holes or burned
areas. (Only if heater has been in use for some
time.)
CAUTION! ELECTRICIAN OR SERVICE PERSON!
1. Before servicing heater, control, or contactor,
turn power off at breaker!
2. Open junction box to make sure wires are
tightly secured with no loose connections.
Heater wire and all connecting wires should be
copper.
3. Check for burned spots or short in wiring of
timer or thermostat.
Warranty on parts is void if installer/electrician fails
to follow necessary wiring information provided or
fails to follow code for proper wire size, amperage,
etc.
HIGH LIMIT CONTROL
Each heater is equipped with a high limit control
which is a safety device. If an abnormal heating
condition should occur, the heater will automatically
shut off, and it will not come on again until it cools.
To reset the high limit, locate the reset button
(bottom front on wall models, behind junction box
at back bottom of heater on oor models) and push
upward until contactor kicks in. If reset button
continues to trip, contact a qualied service person.
Be sure that a GFI has not been installed.
Receptacles OR PLUGS are not allowed in a Sauna
room. If a speaker is installed in a Sauna room, it
should not be installed higher than 3’ from oor,
away from the Sauna heater (consult manufacturer
for ratings).
12
ROOM LIGHT should be a vapor proof, wall-mounted
type, with rough-in box mounted ush with inside
paneling. It should mount 6’6” from oor, not
directly over Sauna heater, and not over upper
benches; light bulb should not exceed 75 watts.
HEATER FENCE is necessary for safety and should
be constructed of 1” x 2” or 2” x 2” softwood
to match Sauna interior. See figures 2–4 for
clearances from Sauna heater. Fence should attach
to wall and should not be placed higher than top of
heater below rock line.
ROOM CONSTRUCTION –
GENERAL INFORMATION
A. FRAMING
• 2” x 4” dry Douglas Fir, 16” o.c.
B. CEILING HEIGHT
• no higher than 7’0”.
C. INSULATION
• R11 Fiberglas with foil back in walls and
ceiling, foil facing into room.
D. DRYWALL
• See local codes. Is not required in most
residences. See local codes commercial. If
drywall is used, apply 1” x 2” nailers so that
wall and ceiling boards can be attached to solid
wood.
E. PANELING
• Use kiln-dried, clear, T & G softwood such
as California Redwood, Western Red Cedar,
Alaska Yellow Cedar, with moisture content
not exceeding 11 %.
F. BENCHES
• Use matching wood of vertical grain with 2”
x 2” tops – ½” spacing – and 2” x 4” facing,
fastening from bottom to prevent burning of
bathers.
G. HEATER GUARDRAIL
• Use matching softwood of 1” x 2” or 2” x 2”.
H. DOOR
• Must open out and should not have a lock. Size
– 2’0” x 6’ 8” with r rails and double sealed,
tempered glass.
I. FLOORING
• concrete, ceramic tile, or heavyduty Vinyl with
walking area of removeable SuperDek.
J. VENTILATION
• should be provided by lower vent close to
heater, 4” from oor, and upper vent on
opposite wall (if possible) 6” from ceiling or
as low as 24” from oor. Vents should be
adjustable and should allow air to change 5
times per hour. Sauna shall be provided with
intended ventilations as required per the local
code authorities.
K. LIGHT
• should be wall-mounted, vapor proof type,
located 6” from ceiling.
L. ACCESSORIES
• bucket, dipper and thermometer are essential.
Thermometer should be placed over the Sauna
heater, 6” from ceiling, for correct temperature
reading. Other accessories such as hygrometer,
sand timer, brushes, etc. are available.
M. MAINTENANCE INSTRUCTIONS
• are included at the end of this manual.
N. WARNING SIGNS
• are furnished with Sauna heater. The metal
“CAUTION” sign should be fastened to wall,
close to heater, in a visible place. The metal
“WARNING” sign should be fastened outside,
to the Sauna room door.
WARNINGS!
Do not smoke, use alcohol, or exercise in the
sauna!
Do not exceed 30 min. in the sauna at one time, as
excessive exposure can be harmful to health. The
sauna should not be used as an endurance test!
Persons with poor health should consult persons
their physicians before using the sauna!
Do not place any combustible material over the
sauna heater (towels, bathing suits, wooden bucket
or dipper)!
Use only clean tap water on the stones – do not use
pool or spa water, as chlorine gas can be produced
and the heating elements can be damaged!
Hyperthermia occurs when the internal temperature
of the body reaches a level several degrees above
the normal body temperature of 98,6ºF. The
symptoms of hyperthermia include an increase in
the internal temperature of the body, dizziness,
lethargy, drowsiness, and fainting.
The effects of hyperthermia include:
A) Failure to perceive heat
B) Failure to recognize the need to exit the room
C) Unawareness of impending hazard
D) Fatal damage in pregnant women
E) Physical inability to exit the room
F) Unconsciousness
Warning – the use of alcohol, drugs or medication
is capable of greatly increasing the risk of fatal
hyperthermia!
13
KIP-60-B1/KIP-60-B3/FLB-60/FLB-60-3
Sauna heaters type -W1, W3, -FIN without parts nr 12, 17 and 18
JH30B2401 - JH80W2083 H12/94
JF30B2401 - JFIN802083 H12/94
1. Wall bracket
2. Tapping screw
3. Sheet screw
4. Casing
5. Heating element
6. Slothead screw
7. Bottom grille
8. Stone compartment, assembled
(frame)
9. Electrical casing, assembled
10. Plate
11. Screw
12. Tapping screw
13. Rating plate
14. Slothead screw
15. Slothead screw
16. Hexagon nut
1 7. Thermostat
18. Timer
19. Terminal strip (USA)
20. Strip xing screw (USA)
21. Base plate
22. Screw
23. Bracket
24. Slothead screw
25. Slothead screw
26. Overheating limiter/switch
2 7. Contactor (USA)
28. Protective grille
14
MAINTENANCE INSTRUCTIONS
1. Use only clean water on Sauna stones. Do not
use spa or pool water as it will destroy your
heater.
2. Clean water should always be used in Sauna
buckets and water should be dumped out
after every use. Scour buckets and dippers
occasionally when lm collects from usage.
Use plastic bucket liner in bucket to prevent
water leakage.
3. Scrub benches with a soft brush, using soap
and water or a mild disinfectant, when needed
– about once a week in commercial Saunas, or
depending upon Sauna usage. For sanitation,
each bather should sit or lie on a towel (this
will prolong bench life).
4. Remove Super Dek and wash waterproof oor
with disinfectant (e.g. Pine Sol) about once a
week or as often as needed. Hose off Super
Dek to clean.
5. To maintain beautiful appearance of Sauna
heater, remove water stains by wiping with a
damp cloth occasionally.
6. Sauna heaters require no special maintenance
when properly installed by a qualied
electrical contractor. After 5 years of usage,
the rocks may need replacing if they have
crumbled or powdered.
7. We strongly recommend a oor that can
be easily cleaned (concrete, ceramic tile,
or a poured type of ooring). When this is
provided, the Sauna can be easily cleaned and
kept in a sanitary condition with little effort. A
carpet is NOT recommended for a Sauna! A
carpet becomes a prefect breeding ground for
bacteria in the moist conditions of a Sauna;
and a carpet promotes the spread of foot
diseases such as athlete’s foot. For the same
reasons, wooden duckboard should not be
used for ooring.
8. In new construction, a oor drain should also
be provided, especially in commercial Saunas
for sanitary cleaning and maintenance.
9. Seal wood around glass in door—inside and
outside—with Thompson’s Water Seal to
prevent warpage.
10. When Sauna wood becomes stained from
perspiration, the wood may be lightly sanded
with ne sandpaper to restore beautiful
appearance. We do not recommend stains
or sealers as toxic vapors may appear when
heated. However, 2 coats of Thompson’s
Water Seal may be used on the wood benches
in a commercial Sauna, so that the wood may
be more easily cleaned and kept sanitary – the
wood will not absorb perspiration.
11. The Sauna room will heat faster if the higher
vent is kept in a closed position when heating.
The lower vent may always be kept in an open
position.
12. Required warning signs should be posted
according to the instructions.
Loading...