Allstar Performance ALL11272 User Manual

Race Car Lift

ASSEMBLY INSTRUCTIONS

Contents List:*

A. Lift Platform Assembly LH (With Hydraulic Cylinder And Down Assist Canister) (1 pc)
B. Lift Platform Assembly RH (With Hydraulic Cylinder And Down Assist Canister) (1 pc)
C. Bridge Assembly With Hose (1 pc)
D. Bridge Assembly (1 pc)
E. Handle Sides (2 pcs)
F. Handle Support Tubes (2 pcs)
G. Riser Blocks (2 pcs)
H. 20' Hydraulic Hose (1 pc)
I. "X" Brace

Hardware Bag Includes:

1/4" x 1-3/4" Bolts (12 pcs)
3/8" x 1/2" Bolts (4 pcs)
1/4" x 3/4" Bolts (2 pcs)
Female Quick Disconnect Fitting (1 pc)
Nuts, Washers And Grease Fittings

A

B

D

* Ensure all contents are included before

assembly begins.

H

F

Female Quick

Disconnect Fitting

G

E

C

I

PLEASE READ!

• The lifting and lowering motion of this lift is accomplished through use of a separate hydraulic pump such as part no.

ALL11280 or comparable 110V style pump.

• This lift is specically designed for use on race cars and not approved for use on street type vehicles. Maximum rated

capacity is 2,400 lbs., do not exceed maximum weight rating, damage to lift may occur.

• Trial test up/down function of lift and make sure all hose connections are tight before subjecting lift to weight of race car.

• Always keep safety in mind and make sure lift is clear of people and objects before raising or lowering.

• Make sure lift has returned to its fully collapsed position and it is clear of all chassis components before driving away.

• Periodically check all hardware and tighten as needed. Check hydraulic hose for signs of damage and replace if necessary

using ALL11274 20' hydraulic hose or ALL11275 30' hydraulic hose.

Allstar Performance 8300 Lane Dr., Watervliet, MI 49098

Phone: [phone] Fax: [phone] www.allstarperformance.com

Form 1125 Page 1 of 2 Rev. 022613

Allstar Performance® will not assume liability for personal or property damage resulting from the use or misuse of any

product we manufacture or sell, whether on the street or on the race track. Purchase and/or use of this product implies

recognition and acceptance of our entire warranty and disclaimer by customer.

Race Car Lift

ASSEMBLY INSTRUCTIONS

1. Remove contents from all cartons and place on a at level surface.

2. Place lift platform assemblies (A & B) in a parallel position so that the Allstar logos are facing out and the hydraulic cylinders
are facing in the same direction as shown in Image 1.

3. Locate the two bridge assemblies (C & D). Position bridge assembly (C) with hydraulic hoses at the end of lift platform as­semblies (A & B) closest to base of hydraulic cylinders as shown in Image 2. Position the remaining bridge assembly (D) in the
same direction as bridge assembly (C) as shown in Image 1.

4. Secure both bridge assemblies using supplied 1/4" x 1-3/4" bolts (install bolts from the bottom, face threads up), lock washers
and nuts. It will be necessary to raise the lift manually approximately 2" and place a stop (such as small length of 2x4 lumber)
between the upper and lower rails to install two of the bridge assembly fasteners.

5. Route hoses under bridge and platform rails. Connect hoses to hydraulic cylinders as shown in Image 2.

6. Install "X" brace as shown in Image 1.

7. Install supplied female quick disconnect to end of hose using thread sealant and attach to male tting on lift.

8. Carefully remove stop supporting lift from step 4.

9. Inate down assist canisters to 100 PSI with the lift in a fully lowered position.

10. Assemble the handle sides (E) to handle support tubes (F) using (4) 3/8" x 1/2" bolts. Attach assembled handle to the lift with
1/4" x 3/4" bolts as shown in Image 3.

11. To prevent damage during shipping, grease ttings are shipped uninstalled. Install ttings in all applicable holes and apply
grease sparingly.

12. Two optional riser blocks (G) are included to install on the lift as needed.

Inate to 100 PSI

Image 1

SAFETY STOPS

Image 2

WARNING - USE BOTH SAFETY STOPS AT ALL TIMES WHEN CAR

LIFT IS RAISED. FAILURE TO USE SAFETY STOPS MAY RESULT IN

PERSONAL INJURY OR PROPERTY DAMAGE.

Allstar Performance 8300 Lane Dr., Watervliet, MI 49098

Phone: [phone] Fax: [phone] www.allstarperformance.com

Image 3

Form 1125 Page 2 of 2 Rev. 022613

Allstar Performance® will not assume liability for personal or property damage resulting from the use or misuse of any

product we manufacture or sell, whether on the street or on the race track. Purchase and/or use of this product implies

recognition and acceptance of our entire warranty and disclaimer by customer.