Page 1
UTM User Manual
www.allo.com Version 2.0 1
Page 2
UTM User Manual
www.allo.com Version 2.0 2
Copy Right
Copyright © 2014 Allo. All rights reserved.
No part of this publication may be copied, distributed, transmitted, transcribed, stored in a
retrieval system, or translated into any human or computer language without the prior written
permission of Allo.com. This document has been prepared for use by professional and properly
trained personnel, and the customer assumes full responsibility when using it.
Proprietary Rights
The information in this document is Confidential to Allo and is legally privileged. The information
and this document are intended solely for the addressee. Use of this document by anyone else
for any other purpose is unauthorized. If you are not the intended recipient, any disclosure,
copying, or distribution of this information is prohibited and unlawful.
Disclaimer
Information in this document is subject to change without notice and should not be construed as
a commitment on the part of allo.com. And does not assume any responsibility or make any
warranty against errors. It may appear in this document and disclaims any implied warranty of
merchantability or fitness for a particular purpose.
Page 3
UTM User Manual
www.allo.com Version 2.0 3
About this manual
This manual describes the allo product application and explains how to work and use it major
features. It serves as a means to describe the user interface and how to use it to accomplish
common tasks. This manual also describes the underlying assumptions and users make the
underlying data model.
Document Conventions
In this manual, certain words are represented in different fonts, typefaces, sizes, and weights.
This highlighting is systematic; different words are represented in the same style to indicate
their inclusion in a specific category. Additionally, this document has different strategies to draw
User attention to certain pieces of information. In order of how critical the information is to your
system, these items are marked as a note, tip, important, caution, or warning.
Icon
Purpose
Note
Tip/Best Practice
Important
Caution
Warning
Bold indicates the name of the menu items, options, dialog boxes, windows and
functions.
The color blue with underline is used to indicate cross-references and hyperlinks.
Numbered Paragraphs - Numbered paragraphs are used to indicate tasks that need to be
carried out. Text in paragraphs without numbering represents ordinary information.
The Courier font indicates a command sequence, file type, URL, Folder/File name e.g.
www.allo.com
Support Information
Every effort has been made to ensure the accuracy of the document. If you have comments,
questions, or ideas regarding the document contact online support: http://support.allo.com
Page 4
UTM User Manual
www.allo.com Version 2.0 4
Table of Contents
About this manual ......................................................................................................................... 3
Document Conventions ................................................................................................................. 3
Support Information...................................................................................................................... 3
1. Introduction ......................................................................................................................... 8
1.1 Overview ................................................................................................................................. 8
1.2 Technical Specifications .......................................................................................................... 9
1.3 Equipment Structure ............................................................................................................. 10
1.3.1 UTM Rear View ............................................................................................................... 10
1.3.2 UTM Front View .............................................................................................................. 10
1.4 Initial Setup & Configuration ................................................................................................. 11
1.4.1 Connecting the Hardware .................................................................................................. 11
1.4.2 Network Deployment ......................................................................................................... 12
1.4.3 Connect UTM Firewall ........................................................................................................ 13
2. Dashboard .......................................................................................................................... 14
3. Device Settings ................................................................................................................... 15
3.1 Host Config ............................................................................................................................ 15
3.2 Admin User ............................................................................................................................ 15
3.3 SSH ......................................................................................................................................... 16
3.4 Web User Interface ............................................................................................................... 16
3.5 Time ....................................................................................................................................... 17
3.6SNMP ...................................................................................................................................... 18
3.7 Certificates ............................................................................................................................ 19
3.7.1Built-in certificates........................................................................................................... 19
3.7.2 Local Certificates ................................................................................................................ 20
3.8 Logging .................................................................................................................................. 21
3.9 Maintenance ......................................................................................................................... 21
3.9.1 Administration ................................................................................................................ 21
3.9.2 Firmware ......................................................................................................................... 22
4. Network Settings ................................................................................................................ 23
4.1 Interfaces ............................................................................................................................... 23
Page 5
UTM User Manual
www.allo.com Version 2.0 5
4.2 Virtual IPS .............................................................................................................................. 23
4.3 VLAN Config ........................................................................................................................... 24
4.4 Zones ..................................................................................................................................... 25
4.5 WAN Load Balancing ............................................................................................................. 26
4.6 Routing .................................................................................................................................. 27
4.6.1 Static Routes ................................................................................................................... 27
4.7 DNS ........................................................................................................................................ 28
4.8 DHCP Server .......................................................................................................................... 28
4.9 Dynamic DNS ......................................................................................................................... 30
4.10 PPPoE Profiles ..................................................................................................................... 31
5. Policy Objects ..................................................................................................................... 32
5.1 Address Groups ..................................................................................................................... 32
5.2 Address objects ..................................................................................................................... 33
5.3 Service Groups ....................................................................................................................... 35
5.4 Service objects ....................................................................................................................... 36
5.5 Web Filter objects ................................................................................................................. 37
6. Policies ............................................................................................................................... 39
6.1 Firewall .................................................................................................................................. 39
6.1.1 Firewall Settings .............................................................................................................. 39
6.1.2 Firewall Policies .............................................................................................................. 40
6.1.3 User Policies .................................................................................................................... 45
6.1.4 Management Access ....................................................................................................... 46
6.1.5 Bandwidth control .......................................................................................................... 47
6.1.6 Port Forwarding/Destination NAT .................................................................................. 50
6.1.7 Source NAT ..................................................................................................................... 51
6.1.8 Static NAT ....................................................................................................................... 52
6.1.9 QOS Settings ................................................................................................................... 53
6.2 IPS .......................................................................................................................................... 53
6.2.1 IPS Settings ..................................................................................................................... 54
6.2.2 Signature Settings ........................................................................................................... 55
6.2.3 Custom Signatures .......................................................................................................... 56
Page 6
UTM User Manual
www.allo.com Version 2.0 6
6.3 VPN ........................................................................................................................................ 57
6.3.1 SSLVPN Server Settings ................................................................................................... 58
6.3.2 SSLVPN Client Profiles..................................................................................................... 60
6.3.3 SSLVPN P2P Policies ........................................................................................................ 61
6.3.4 Client Certificates ........................................................................................................... 63
6.3.5 IPSec Settings .................................................................................................................. 64
6.3.6 IPSec Policies................................................................................................................... 65
6.4 Web Proxy ............................................................................................................................. 70
6.4.1 Proxy Configuration ........................................................................................................ 71
6.4.2 Web filter blocking page ................................................................................................. 73
6.4.3 User Authentication ....................................................................................................... 73
6.4.4 Web Cache Management ............................................................................................... 74
6.4.5 External Proxy ................................................................................................................. 75
6.5 Anti Virus ............................................................................................................................... 75
6.5.1 Anti Virus Settings .......................................................................................................... 76
6.6 Users ...................................................................................................................................... 76
6.6.1 User Groups .................................................................................................................... 77
7. Status Information .............................................................................................................. 78
7.1 Interfaces ............................................................................................................................... 78
7.2 DHCP leases ........................................................................................................................... 78
7.3 Firewall .................................................................................................................................. 79
7.3.1 Connection Statistics ...................................................................................................... 79
7.3.2 Connection info .............................................................................................................. 80
7.3.3 Bandwidth Usage per IP ................................................................................................. 80
7.4 System Log ............................................................................................................................. 81
7.5 IPS Alerts................................................................................................................................ 82
7.6 SSLVPN Client Status ............................................................................................................. 82
7.7 SSLVPN P2P Status................................................................................................................. 83
7.8 IPSec Status ........................................................................................................................... 83
7.9 Service Status ........................................................................................................................ 84
8. Diagnostics ......................................................................................................................... 86
Page 7
UTM User Manual
www.allo.com Version 2.0 7
8.1 Diagnostics Report ................................................................................................................ 86
8.2 Ping ........................................................................................................................................ 87
8.3 Trace Route ........................................................................................................................... 87
8.4 DNS Lookup ........................................................................................................................... 88
8.5 Packet Trace .......................................................................................................................... 89
9. Reports ............................................................................................................................... 90
9.1 System ................................................................................................................................... 90
9.1.1System usage ................................................................................................................... 90
9.2 Firewall .................................................................................................................................. 90
9.2.1 Internet Usage ................................................................................................................ 90
9.2.2 Bandwidth Usage ............................................................................................................ 91
9.3 Web filter............................................................................................................................... 92
9.4 IPS Alert Reports.................................................................................................................... 92
Frequently Asked Questions (FAQs) ........................................................................................ 93
Glossary ................................................................................................................................. 95
Page 8
UTM User Manual
www.allo.com Version 2.0 8
1. Introduction
1.1 Overview
Shield UTM Appliances is the Unified Threat Management solution that target the security needs
for Home/SOHO users. The appliance provides the integrated Firewall, Intrusion Prevention,
SSLVPN functionalities.
Unified threat management (UTM) is an emerging trend in the network security market. UTM
appliances have evolved from traditional firewall/VPN products into a solution with many
additional capabilities. UTM solutions also provide integrated management, monitoring, and
logging capabilities to streamline deployment and maintenance. UTM appliances combine
firewall, gateway anti-virus, and intrusion detection and prevention capabilities into a single
Platform. UTM is designed protect users from blended threats while reducing complexity.
The Unified Threat Management (UTM) Appliance connects your local area network (LAN) to the
Internet through one or two external broadband access devices such as cable mode ms or DSL
modems. Dual wide area network (WAN) ports allow you to increase the effective data rate to
the Internet by utilizing both WAN ports to carry session traffic, or to maintain a backup
connection in case of failure of your primary Internet connection. As a complete security
solution, the UTM combines a powerful, flexible firewall with a content scan engine that protect
your network from denial of service (DoS) attacks, unwanted traffic, traffic with objectionable
content, spam, phishing, and Web-borne threats such as spyware, viruses, and other malware
threats. The UTM provides advanced IPSec and SSL VPN technologies for secure and simple
remote connections. The use of Gigabit Ethernet LAN and WAN ports ensures extremely high
data transfer speeds. The UTM is a plug-and-play device that can be installed and configured
within minutes
Page 9
UTM User Manual
www.allo.com Version 2.0 9
1.2 Technical Specifications
No of Interfaces
Two 1Gbps WAN port & four 1Gbps LAN ports, 1 console
interface, 1 USB port
Status Firewall Inspection
Yes
Deep Packet Inspection
Yes
Signatures Support
~4000 active signatures from snort VRT/emerging threats
Application Protocols Detection
70+
Maximum No of Connections
20000
Maximum No of New Connections
Per Second
1800
Maximum No of SSLVPN Clients
100
Authentication
X509 certificates, internal user DB
Logging
Local log viewer, Syslog
Device Management
HTTPS GUI, SNMP
Hardware
Cavium Octeon II 63xx, 2cores 800MHz
RAM
1 GB
Page 10
UTM User Manual
www.allo.com Version 2.0 10
Notification LEDs (On the front panel of the UTM)
1.3 Equipment Structure
1.3.1 UTM Rear View
Figure 1: UTM Rear View
1.3.2 UTM Front View
Figure 2: UTM Front View
Page 11
UTM User Manual
www.allo.com Version 2.0 11
1.4 Initial Setup & Configuration
1.4.1 Connecting the Hardware
Figure 3: Connecting the Hardware
Page 12
UTM User Manual
www.allo.com Version 2.0 12
1.4.2 Network Deployment
Figure 4: Network Deployment
Default Configuration Port IP Ares
Ethernet Port
IP Address
LAN 0-3 > eth1
10.0.0.1/255.255.255.0
WAN > eth0
10.1.0.1/255.255.255.0
Management VLAN
(Accessible via LAN
Ports)
192.168.1.1/255.255.255.0
Default Firewall Mode
Router
Page 13
UTM User Manual
www.allo.com Version 2.0 13
Management Service
Default Credentials
Web UI
admin/admin
SSHCLI
admin/admin123
1.4.3 Connect UTM Firewall
Connect the appliance to the power socket using the power cable.
Connect the PC to one of the LAN ports of the Appliance.
Your PC will get an IP address from 10.0.0.0/24 subnet.
You can access the Configuration management WebUI from the browser on the PC with
the URL http://10.0.0.1/ or http://192.168.1.1
The recommended browsers for accessing UTM 1.0 WebUI is Mozilla Firefox / Internet
Explorer 8 and above.
Accept the Self signed SSL Certificate and Login to the UTM appliance using default Web
UI credentials.
Figure 5: UTM Login page
WebUI is running on the secure http server. Accessing http://10.0.0.1 or
http://192.168.1.1 will redirect to https://10.0.0.1/ or https://192.168.1.1/
Page 14
UTM User Manual
www.allo.com Version 2.0 14
2. Dashboard
On logging into the UTM WebUI, the dashboard will be shown. The user can visit the dashboard
page from the any configuration page in the UTM WebUI, by clicking the UTM Product Icon that
appears in the left corner of the Top panel.
The Dashboard shows memory usage, CPU usage, uptime of the device, a list of all interfaces
with their IP address and status, etc..,
Figure 6: Dashboard
Page 15
UTM User Manual
www.allo.com Version 2.0 15
3. Device Settings
3.1 Host Config
Navigate through Device Settings > Host Config
Configuring hostname and domain name of the device.
Figure 7: Host Config
3.2 Admin User
Navigate through Device Settings > Admin User
The user allows for configuring web UI administrator username and password. User can change
the web UI username and password.
Figure 8: Admin user
Page 16
UTM User Manual
www.allo.com Version 2.0 16
3.3 SSH
Navigate through Device Settings > SSH
Secure SHell (SSH) is a network protocol for secure data communication, remote command line
login, remote command execution, and other secure network services between two networked
computers. It connects, via a secure channel over an insecure network, a server and a client
running SSH server and SSH Client programs, respectively.
SSH works on top of TCP protocol and its default port number is 22.
It is used to login into the device securely using public and private host keys. This section includes
port and session timeout. Session timeout specifies how long the user session show is valid.
Figure 9: SSH
3.4 Web User Interface
Navigate through Device Settings> Web User Interface
It helps configuring web UI port and session time out. Session timeout specifies how long the
web UI session should be valid.
Page 17
UTM User Manual
www.allo.com Version 2.0 17
Figure 10: Web User Interface
3.5 Time
Navigate through Device Settings > Time
The user allows for configuring time settings to the device using NTP server or using manual
settings. Using sync with NTP, the user has to provide the NTP servers to sync with the time along
with the zone specified in the zone list. In manual settings, user has to set the hour/minute and
select hour format (AM/PM), date/month/year. The Time zone list provides a list of all time
zones. NTP synchronizes for every specified update interval.
Figure 11: Time
Page 18
UTM User Manual
www.allo.com Version 2.0 18
3.6SNMP
Navigate through Device Settings > SNMP
Simple Network Management Protocol (SNMP) is an application layer protocol for managing
devices on IP networks. It runs on port 161 and 162(trap) and mostly used in network
management systems to monitor network-attached devices.
In UTM's SNMP can be Enabled/Disable by clicking on the respective buttons. User can configure
any appropriate System Name, System Contact, and System Location into those fields.
Access Control List: SNMP Access controls Lists (ACL) are configured in order to allow the SNMP
traffic through the UTM Device.
Figure 12: Add Access Control List
Trap Servers List: A trap is an SNMP agent's way of notifying the manager that "something is
wrong". UTM SNMP traps will capable of sending SNMP traps on their own to alert an SNMP
manager when they experience a problem.
Page 19
UTM User Manual
www.allo.com Version 2.0 19
Figure 13: Create Trap Servers List
Figure 14: SNMP
3.7 Certificates
Navigate through Device Settings > Certificates
In this section includes two sections:
3.7.1Built-in certificates
#Built-In which includes default root certificates about 200+.
Page 20
UTM User Manual
www.allo.com Version 2.0 20
Figure 15: Built-in Certificates
3.7.2 Local Certificates
# Local which user uploaded certificates in PKCS12 format contains root certificate, server
certificate and server key. Challenge password is the password for extracting uploaded PKCS12
file and New Certificate Name is the name for uploaded certificate.
Figure 16: Local Certificates
Page 21
UTM User Manual
www.allo.com Version 2.0 21
3.8 Logging
Navigate through Device Settings > Logging
Configuring logging server address to where the log information has to be sent like Firewall
alerts, IPS alerts, VPN alerts etc.
Figure 17: Logging
3.9 Maintenance
Navigate through Device Settings > Maintenance
This section consists of two parts: Administration and Firmware.
3.9.1 Administration
Navigate through Device Settings > Maintenance > Administration
It includes
#restart services which restart all the services in device like IPS, VPN, etc..
#restart appliance which reboots the device.
# To shut down appliance which turns off the device.
#configuration backup includes
Page 22
UTM User Manual
www.allo.com Version 2.0 22
Backup configuration which provides facility to take back up of current configuration settings.
Restore configuration which provides facility to restore the configuration which is provided.
Figure 18: Administration
3.9.2 Firmware
Navigate through Device Settings > Maintenance > Firmware
It includes
#factory reset- it resets the device to default configuration settings.
#uploads firmware which provides the facility to upload the latest firmware build and install it
on the device.
# the firmware last update shows the last firmware update information.
Figure 19: Firmware
Page 23
UTM User Manual
www.allo.com Version 2.0 23
4. Network Settings
4.1 Interfaces
Navigate through Network > Interfaces
In this section, we can configure interfaces like WAN (eth0), LAN (eth1), and whether the
interface can be in DHCP mode or Static mode. By default WAN interface has IP address
10.1.0.1/255.255.255.0 which is in Static mode and LAN interface has IP address
10.0.0.1/255.255.255.0 which has DHCP running on this interface.
We can configure gateway to the interfaces only in Static mode. And also Maximum
Transmission Unit (MTU) (68 - 1500) (communications protocol of a layer is the size (in bytes) of
the largest protocol data unit that the layer can pass onwards) for each interface.
Select which interface will be used for this connection either on external or internal interfaces.
PRIMARY means the connection will be on the external interface.
Figure 20: Interfaces
4.2 Virtual IPS
Navigate through Network > Virtual IPS
UTM's VIPs addressing enables hosting for several different applications and virtual appliances
on a server with only one logical IP address
Page 24
UTM User Manual
www.allo.com Version 2.0 24
Figure 21: Create Virtual IPS
Figure 22: Virtual IPS
4.3 VLAN Config
Navigate through Network > VLAN Config
A VLAN is a group of end stations with a common set of requirements, independent of physical
location. VLANs have the same attributes as a physical LAN but allow you to group end stations
even if they are not located physically on the same LAN segment.
The user can configure Virtual Local Area Network (VLAN) by providing information like Tag ID
which specifies unique tag id for each VLAN, interface name to be selected. VLAN routing, IP
address and net mask for VLAN whether to enable DHCP for VLAN. By default management
VLAN is added to the device.
Page 25
UTM User Manual
www.allo.com Version 2.0 25
Figure 23: Create VLAN
Figure 24: VLAN Config
4.4 Zones
Navigate through Network > Zones
UTM zones are used to create any area that is separated from another. It allows user to create
their individual LAN and WAN Zone according to their network environment naturally.
Page 26
UTM User Manual
www.allo.com Version 2.0 26
Figure 25: Create Zone
Figure 26: Zones
4.5 WAN Load Balancing
Navigate through Network > WAN Load Balancing
UTM has the ability to balance traffic across two WAN links without using complex routing
protocols. It uses following 4 techniques to balance load across two WAN:
Active Failover
Round Robin
Spill over
Weight based
User can make use of any above Load balancing technique for managing their network traffic.
Page 27
UTM User Manual
www.allo.com Version 2.0 27
Figure 27: Web Load Balancing
4.6 Routing
4.6.1 Static Routes
Navigate through Network > Routing> Static Routes
We configure routes to the destination network by specifying destination address, net mask and
metric value (0 - 31). Gateway is optional.
Figure 28: Routing
Page 28
UTM User Manual
www.allo.com Version 2.0 28
Figure 29: Static Routes
4.7 DNS
Navigate through Network > DNS
Domain Name System (DNS) is a service translates domain names into IP addresses. In UTM user
can configure Primary DNS, Secondary DNS, and Tertiary DNS by giving either DNS server IP or
name.
Figure 30: DNS
4.8 DHCP Server
Navigate through Network > DHCP Server
It is used to configure automatic dynamic and static IP leasing to DHCP requests received from
network hosts.
We can configure Dynamic Host Configuration Protocol (DHCP) for each LAN and VLAN
interfaces. We need to specify interface name, start address, end address, network mask and
gateway. And also specify primary DNS (mandatory), secondary DNS, WINS and Domain.
Page 29
UTM User Manual
www.allo.com Version 2.0 29
Figure 31: Add DHCP Server Settings
Conflict time (60 – 3600)
Decline time (60 – 3600)
Offer time (60 – 3600) and
Max lease (1 – 125).
We can configure static mapping by adding the MAC address of a client , the IP address assign to
clients, hostname to the client and whether to enable this rule or not.
Figure 32: DHCP Server
Page 30
UTM User Manual
www.allo.com Version 2.0 30
4.9 Dynamic DNS
Navigate through Network > Dynamic DNS
It is used to configure access to third-party dynamic DNS service providers
Figure 33: Add DDNS
If another Dynamic DNS Profile has been enabled on the WAN interface already; you can
enable only one Dynamic DNS profile on the WAN interface at a time.
Figure 34: Dynamic DNS
Page 31
UTM User Manual
www.allo.com Version 2.0 31
4.10 PPPoE Profiles
Navigate through Network > PPPoE Profiles
The Point-to-Point Protocol over Ethernet (PPPoE) is a network protocol for encapsulating PPP
frames inside Ethernet frames and allows data communication between two network entities or
points. UTM allows user to configure PPPOE profiles in PAP /CHAP authentication modes.
Figure 35: Create PPPoE Profile
Figure 36: PPPoE Profiles
Page 32
UTM User Manual
www.allo.com Version 2.0 32
5. Policy Objects
Policy objects are building blocks for configuring Firewall, VPN, Web Filter, User Policies etc in
UTM. They are something that can be configured once and then used over and over again to
build what you need. They can assist in making the administration of the UTM unit easier and
more intuitive as well as easier to change.
By configuring these objects with their future use in mind as well as building in accurate
descriptions the firewall will become almost self documenting. That way, months later when a
situation changes, you can take a look at a policy that needs to change and use a different
firewall object to adapt to the new situation rather than build everything new from the ground
up to accommodate the change.
5.1 Address Groups
Navigate through Policy Objects > Address Groups
Address Objects are grouped together to create some policies called as Address Groups. Policies
can apply to created group itself.
If you have a number of addresses or address ranges that will commonly be treated the same or
require the same security policies, you can put them into address groups, rather than entering
multiple individual addresses in each policy refers to them. It saves user time.
It specifies the group of address objects which includes network address, host address; address
range of hosts etc..,
Group Name: It specifies the unique address group name which can be used in Policies like
Firewall Policies, User Policies, etc..; it ranges from 5 – 32 characters. Eg. LAN_GROUP
Page 33
UTM User Manual
www.allo.com Version 2.0 33
Figure 37: Add Address Group
Figure 38: Address Groups
5.2 Address objects
Navigate through Policy Objects > Address Objects
Address Objects defines sources and destinations of network traffic and are used when creating
policies. When properly set up these Address objects can be used with great flexibility to make
the configuration of firewall/Web filtering policies simpler and more intuitive. The UTM policies
verify and check the IP addresses contained in packet headers with a security policy’s source and
destination addresses to determine if the security policy matches the traffic.
Page 34
UTM User Manual
www.allo.com Version 2.0 34
It determines the network address, host address, range of addresses and Mac address of the
server. Address object name specifies the unique name for address object which used in
Policies, etc.., it ranges from 3 – 32 characters. Eg. LAN_NETWORK.
In network address, user has to define the IP address and net mask (Eg. IP address: 10.0.0.0, Net
mask: 255.255.255.0). In host address, user has to specify a valid host address (Eg. 10.0.0.5). In
range of addresses, user has to specify start and end address (Eg. Start IP: 10.0.0.5, End IP:
10.0.0.8). In Mac address, user has to specify a valid Mac address in ':' format (Eg.
11:22:33:44:55:66).
Figure 39: Create Address Object
Figure 40: Address Objects
Page 35
UTM User Manual
www.allo.com Version 2.0 35
5.3 Service Groups
Navigate through Policy Objects > Service Groups
Like Address Objects, services can also be bundled into Service groups for ease of
administration.
Ex: TCP_Services (HTTP, FTP, SMTP)
UDP_SERVICES (DNS, TFTP)
It designates the group of service targets which includes services like ssh, http, SMTP, etc..,
Group Name: It specifies the unique group name which can be used in Policies like Firewall
Policies, User Policies, etc... It ranges from 3 – 32 characters. Eg. WEB_SERVICES
Figure 41: Create Service Group
Page 36
UTM User Manual
www.allo.com Version 2.0 36
Figure 42: Service Groups
5.4 Service objects
Navigate through Policy Objects > Service Objects
TCP/IP suite is having a number of different services and Protocols. These protocols & Services
using port number from 1-65535 port numbers. Each port number is having its own service.
For example HTTP having port number 80 (TCP)
SMTP having port number 25(TCP)
DNS having port number 53 (UDP) etc.
Using port number we can create services and configure Firewall, NAT, Web Filtering policies
etc.
It specifies the services like SSH, http, SMTP, SIP, etc.., Object name specifies the unique name
for service object which used in Policies, etc.., and it ranges from 3 – 32 characters. Eg. Http.
Figure 43: Create Service Object
Page 37
UTM User Manual
www.allo.com Version 2.0 37
Protocol: It specifies which protocol to be used for the service object. Protocols like TCP, UDP,
TCP_UDP and ICMP.
Port: It specifies the port for protocols like TCP and UDP. Eg. 22
ICMP type: It specifies the type of icmp to be used for the service object. Eg. Type 0: Echo Reply
Figure 44: Service Objects
5.5 Web Filter objects
Navigate through Policy Objects > Web Filter Objects
It narrows down the list of objects which are used in Web Filtering for blocking specific sites
using the URL, IP Address, Keyword and Categories.
Figure 45: Create Web Filter Objects
Page 38
UTM User Manual
www.allo.com Version 2.0 38
Name: unique name for web filter objects. It ranges from 3 -32 characters. Eg. Videos
URL: It specifies the URL list, which is used in web filtering for blocking the sites mentioned. Eg.
www.allo.com
IP address: It specifies the IP addresses of sites to be blocked using web filtering. Eg. IP address
of www.google.com is 173.194.117.114.
Keyword: It specifies a list of keywords which are used to block sites based on the keywords
listed. Eg. Face to block Facebook site.
Categories: It specifies a list of categories like ads, blog, etc.., Eg. Ads
Figure 46: Web Filter objects
Page 39
UTM User Manual
www.allo.com Version 2.0 39
6. Policies
6.1 Firewall
Navigate through Policies> Firewall
It filters the inbound and outbound traffic on a network, allowing safe & secure traffic to pass
while blocking insecure traffic.
A firewall is used to maintain a network secure. The primary objective is to control the incoming
and outgoing network traffic by analyzing the data packets and determining whether it should
be allowed through or not, based on a configured rule set.
A network's firewall builds a bridge between an internal network that is assumed to be
securing, trusted, and another network, usually an external (Untrusted) network, such as the
Internet, that is not assumed to be secure and trusted.
6.1.1 Firewall Settings
Navigate through Policies> Firewall > Firewall Settings
Firewall Settings allows user to configure TCP connection timeout, TCP Session timeout,
TCP/UDP connection Flood Detect Rate in Global firewall Settings.
Figure 47: Firewall Settings
Page 40
UTM User Manual
www.allo.com Version 2.0 40
UTM Firewall works in two modes:
I. Routed
II. Transparent
Routed Mode
UTM firewall having LAN (Private/trusted) &WAN (Public/Untrusted) networks. Routed mode
allows traffic coming from private network (LAN) to Public network (WAN) without much
inspection. It will filter and do the deep inspection on whatever the traffic coming from WAN to
LAN. If any malicious traffic coming from WAN/Public network to LAN then UTM Firewall and IPS
(Intrusion Prevention System) will simply drop the particular packet.
Transparent Mode
There are no LAN & WAN networks it works in bridge mode. Transparent mode is typically used
to apply the features such as Security Profiles etc. on a private network where the UTM unit will
be behind an existing firewall or router.
The characteristics of transparent mode are:
• The UTM device is invisible to the network.
• All of its interfaces are on the same subnet and having the IP addresses which are in same
network.
6.1.2 Firewall Policies
Navigate through Policies> Firewall > Firewall Policies
The default policy configuration of the UTM Firewall allows all connections from LAN to
WAN.
To check /Modify Navigate to: Policies > Firewall Policies > LAN > Edit > Policy Setting >
(You can see here Destination Zone ‘WAN’ Action ‘Allow’ Direction ‘OUTBOUND’)
Page 41
UTM User Manual
www.allo.com Version 2.0 41
Figure 48: Edit Firewall Policy
Click Edit button, user can edit the preconfigured firewall rules according to user network
structure.
Policy Rules
User can configure policy rules by making use of created address objects and Service objects.
For example, if user wants to block SSH from host 192.168.0.25 then user has to create address
object for 192.168.0.25 and service object SSH.
Page 42
UTM User Manual
www.allo.com Version 2.0 42
Figure 49: Create Policy Rules
Application Control
The online threat to productivity and security in your organization has evolved beyond
simple web traffic. Problematic applications such as Bit Torrent, Skype, and TOR can compromise
available bandwidth and expose you to inappropriate and illegal activity. Using protocols are
not identified by conventional web filters, these types of applications are difficult to stop.
Shield UTM allows you to stop this traffic at the gateway itself.
Page 43
UTM User Manual
www.allo.com Version 2.0 43
Figure 50: Application Control
Web Filtering
A Web filter is a program that can screen an incoming Web page to determine whether some or
all of it should not be displayed to the user. The filter checks the origin or content of a Web page
against a set of rules provided by company or person who has installed the Web filter.
It allows an enterprise or individual user to block out pages from Web sites that are likely to
include objectionable advertising, pornographic content, Spyware, Viruses and other
objectionable content. Vendors of Web filters claim that their products will reduce recreational
Internet surfing among employees and secure networks from Web-based threats.
Page 44
UTM User Manual
www.allo.com Version 2.0 44
Figure 51: Web Filtering
The Web filter works primarily by looking at the destination location request for a HTTP(S)
request made by the sending computer. If the URL is on a list that you have configured to list
unwanted sites, the connection will be disallowed. If the site is part of a category, then user can
configured to deny connections to the session. User can also configure the content filter to
check for specific key strings of data on the actual web site and if any of those strings of data
appear the connection will not be allowed.
Page 45
UTM User Manual
www.allo.com Version 2.0 45
Figure 52: Firewall Policies
6.1.3 User Policies
Navigate through Policies> Firewall > User Policies
UTM allows user to configure their own User Policies according to their need in firewall.
Figure 53: Create User Policy
Page 46
UTM User Manual
www.allo.com Version 2.0 46
Figure 54: User Policies
6.1.4 Management Access
Navigate through Policies> Firewall > Management access
Management Access rules define the rules that traffic must meet to happen through an
interface.
When you define rules for outgoing traffic, i.e. LAN Management Access profile, they are utilized
to the traffic before any other policies are enforced.
When you define rules for incoming traffic i.e. WAN Management Access profile, they are
applied to the traffic before any other policies are applied.
Page 47
UTM User Manual
www.allo.com Version 2.0 47
Figure 55: Add Management Access
Figure 56: Management Access
6.1.5 Bandwidth control
Navigate through Policies> Firewall > Bandwidth Control
UTM Bandwidth control is designed to minimize the impact caused when the connection is
under heavy load. Using Bandwidth Control, we can assign a specific minimum or maximum
bandwidth for each computer, which means they have less impact on each other.
In UTM user can create BW profile in 2 ways:
Page 48
UTM User Manual
www.allo.com Version 2.0 48
i. Priority
ii. Rate
i. Priority
In Priority type user can select any one of following priority value to configure their BW profile.
They are:
o 0 Realtime
o 1 Highest
o 2 High
o 3 Medium High
o 4 Medium
o 5 Medium Low
o 6 Low
o 7 Lowest
Figure 57: Add Bandwidth Control Profile
ii. Rate
In Rate, user can configure BW (Bandwidth) control profile by ID, Min & Max Download Rate,
and Min & Max Upload Rate. Rates are in kbps only.
Page 49
UTM User Manual
www.allo.com Version 2.0 49
Figure 58: Add Bandwidth Control profile-Rate
Figure 59: Bandwidth Control
NAT
NAT (Network Address Translation) translates the source IP address of a device on one
network interface, usually the Internal, to a different IP address as it leaves another interface,
usually the interface connected to the ISP and the Internet. This enables a single public address
to represent a significantly larger number of private addresses.
UTM NAT Supports following types:
i. Static NAT
ii. Source NAT
iii. Dynamic NAT/Port Forwarding
Page 50
UTM User Manual
www.allo.com Version 2.0 50
6.1.6 Port Forwarding/Destination NAT
Navigate through Policies> Firewall > Port Forwarding
It changes the destination address in IP header of a packet and also changes the destination
port in the TCP/UDP headers. The typical usage is to redirect incoming packets with a
destination of a public address/port to a private IP address/port inside your network.
It is used to forward incoming connection requests to internal network hosts.
Figure 60: Add Destination NAT Rule
Figure 61: Port Forwarding Destination NAT
Page 51
UTM User Manual
www.allo.com Version 2.0 51
6.1.7 Source NAT
Navigate through Policies> Firewall > Source NAT
It changes the source address in IP header of a packet and also changes the source port in the
TCP/UDP headers. The typical usage is to change the private address/port into a public
address/port for packets leaving your network.
Masquerading is a special form of Source NAT where the source address is unknown at the
time the rule is added to the tables in the kernel. If you want to allow hosts with private address
behind your firewall to access the Internet then external address is variable (DHCP).
Masquerading will modify the source IP address and port of the packet to be the primary IP
address assigned to the outgoing interface
Figure 62: Add Source NAT Rule
UTM Source NAT changes the source address in the IP header of a packet. It may also change
the source port in the TCP/UDP headers. The typical usage is to change the private address/port
into a public address/port for packets leaving your network.
User can configure SNAT by making use of interface, Source & Destination address, Source &
Destination port and External Address & port.
Page 52
UTM User Manual
www.allo.com Version 2.0 52
Figure 63: Source NAT
6.1.8 Static NAT
Navigate through Policies> Firewall > Static NAT
UTM Static NAT changes the source address in the IP header of a packet. It also changes the
destination address in the IP header of a packet which is coming from the public network. User
can configure Static NAT by making use of the interface, internal address &port, External
Address & port/service. In Static NAT one internal IP address is always mapped to the same
public IP address.
Figure 64: Add Static NAT Rule
Page 53
UTM User Manual
www.allo.com Version 2.0 53
Figure 65: Static NAT
6.1.9 QOS Settings
Navigate through Policies> Firewall > QOS Settings
(Quality of Service) In relation to leased lines, QOS is a contractual guarantee of uptime and
bandwidth.
6.2 IPS
Navigate through Policies> IPS
Intrusion Prevention System (IPS) can detect and block attacks before damage has been done. It
performs in-line inspection of network traffic in real-time manner. The inspection identifies
attacks using known vulnerabilities of commonly used software products and protocols. The
attack patterns with unusual activity are based on connection sequences or traffic length.
Figure 66: DSCP Mapping
Page 54
UTM User Manual
www.allo.com Version 2.0 54
UTM IPS supports:
i. Predefined IPS signatures.
UTM is having predefined signatures for all known attacks.
ii. Custom IPS signatures.
Custom Signatures allows user to configure own signatures to block any kind of attacks that
are targeting to your network.
6.2.1 IPS Settings
Navigate through Policies> IPS > IPS Settings
Intrusion prevention systems (IPS), also known as intrusion detection and prevention systems
(IDPS) are network security appliances that monitor network and/or system activities for
malicious activity.
In IPS Settings, users can enable/disable the IPS by radio button present at GUIs.
User can Enable Signature Update by making use of given URL and even he can schedule the
update the signatures based on a time basis like Monthly, Daily and Weekly. Or he can download
and update the signatures.
Figure 67: IPS Settings
Page 55
UTM User Manual
www.allo.com Version 2.0 55
6.2.2 Signature Settings
Navigate through Policies> IPS > Signature Settings
UTM user can change signature policy actions by selecting edit Buttons. He can change policy
action to Prevent/Inspect/Disable in GUI. UTM user can have flexibility to change policy actions
by following ways:
By ID
By Category
By Severity
By ID
Figure 68: Signature Setting by ID
By Category
Page 56
UTM User Manual
www.allo.com Version 2.0 56
Figure 69: Signature Settings by Category
By Severity
Figure 70: Signature Settings by Severity
6.2.3 Custom Signatures
Navigate through Policies> IPS > Custom Signatures
UTM user can customize or write their signatures for any newer attacks. The UTM IPS GUI allows
user to add signatures, Export Signatures and preview signatures.
Page 57
UTM User Manual
www.allo.com Version 2.0 57
When adding any new signatures, user just makes use of available options to customize their
signatures.
Figure 71: Add Custom Signature
Figure 72: Custom Signatures
6.3 VPN
Navigate through Policies> VPN
A virtual private network (VPN) tunnel provides a secure communication channel either between
two gateway VPN firewalls or between a remote VPN client and gateway VPN firewall. As a
Page 58
UTM User Manual
www.allo.com Version 2.0 58
result, the IP address of at least one of the tunnel endpoints needs to be known in advance in
order for the other tunnel endpoint to establish (or reestablish) the VPN tunnel.
This private network used as a public network to connect remote sites or users together. The
VPN uses "virtual" connections routed through the Internet from the business's private network
to the remote site or employee.
6.3.1 SSLVPN Server Settings
Navigate through Policies> VPN > SSLVPN Server Settings
It allows users to remotely access restricted network resources via a secure and authenticated
pathway. By encrypting all network traffic and giving the appearance that the user is on the local
network, regardless of geographic location. This protocol achieves a higher level of compatibility
with client platforms and configurations for remote networks and firewalls, providing a more
reliable connection.
It allows access to administrative systems, critical infrastructure, and sensitive information
maintained by system administrators. SSL VPN access can be granted to system administrators as
well as vendors and other external collaborators.
Figure 73: SSLVPN Server Settings
Enable: To enable SSLVPN
Port: Client can use this port to connect
Page 59
UTM User Manual
www.allo.com Version 2.0 59
Protocol: Sever and client to use protocol (UDP/TCP)
Preferred Cipher Suite: Cipher used for encrypting of data b/w client and server
Server Certificate: Certificates used server for the connection.
Compression: Enable/disable of compressed data
Authentication Mode: Server and client can communicate in 3 modes
Password: where Client and Server authentication is done using user name and password. User
credentials are configured in Users pages.
Certificate: Authentication is performed by using credentials.
Two factors: Authentication is done in both password and certificate mode
Max Clients: Maximum number of clients that SSLVPN server can connect
Client Routes: Network on the server side which is accessible for all clients connected
Figure 74: Add Client Route
Session Timeout: If no traffic b/w SSLVPN server and customer. Then the client gets
disconnected after the Session
Tunnel All Traffic: Enable/Disable all the traffic from client side need to be passed via SSLVPN
server.
Route client to client directly: If checked, then client connected with SSLVPN server can
communicate with each other.
Page 60
UTM User Manual
www.allo.com Version 2.0 60
6.3.2 SSLVPN Client Profiles
Navigate through Policies> VPN > SSLVPN Client Profiles
The Customer demands to be plugged in and configured here.
Figure 75: Configure SSLVPN Client Profile
User Name: Select the username to be configured. (The user is added in Users tab)
Remote Nets: Clients side network to be accessed via server side
Push Nets: Server side network to be accessed from configured user.
Static IP: Assigning IP to the user
Allo/Deny: if checked the this user is authenticated
Enable access via Secondary WAN: If the dual WAN is enabled, then the customer can relate
with any of the one side (applied in multiple WANs)
Enable Tunnel all traffic: if checked, all the traffic for this user is sent via SSLVPN server
Page 61
UTM User Manual
www.allo.com Version 2.0 61
Figure 76: SSLVPN Client Profiles
6.3.3 SSLVPN P2P Policies
Navigate through Policies> VPN > SSLVPN P2P Policies
SSLVPN P2P tunnel provides a good communication channel between two gateway VPN firewalls.
Figure 77: Create SSLVPN P2P Policies
Protocol and Mode: Protocol used to communicate between 2 VPN gateways
Protocol UDP:
Page 62
UTM User Manual
www.allo.com Version 2.0 62
Tunnel can be created in all the 3 modes
Mode p2p is selected on 1
st
gateway then p2p gateway has to select on the remote gateway
Mode Server is selected on 1
st
gateway then the Client has to be configured on the remote
gateway.
Protocol TCP:
Tunnel can be created in all the 2 modes
Mode Server is selected on first gateway then the Client has to be configured on the remote
gateway
Local Gateway: gateway IP of first gateway
Local Tunnel Address: Virtual tunnel IP
Local Port: Port used to connect
Remote Gateway: Gateway IP of the 2
nd
gateway to which it has to relate.
Remote Tunnel Address: virtual tunnel IP to be connects of the remote gateway.
Remote Port: Port used to connect to the remote gateway
Preferred Cipher Suite: Cipher to be used in encryption b/w gateways
Authentication:
Pre shared key: Pre Shared Key dialog is enabled .Press generate button to generate the key.
Use the generate key on the remote gateway
Certificate: Certificate Use the same certificate on both gateways
Compression: enable/disable of compression of data
Remote Nets: remote gateway network to be accessed from 1 gateway side
Inactive Timeout: If no traffic b/w two gateways at this time. Communication is
terminated b/w gateway
Notify On Exit: If one side of the gateway terminates, then it notifies the remote side.
This is applicable for the UDP protocol.
Page 63
UTM User Manual
www.allo.com Version 2.0 63
Figure 78: SSLVPN P2P Policies
6.3.4 Client Certificates
Navigate through Policies> VPN > Client Certificates
The user can generate certificates signed by Device RootCa .Common name should match with
SSLPVN client profile user name.
Figure 79: Regenerate Client Certificate
Page 64
UTM User Manual
www.allo.com Version 2.0 64
Figure 80: Clients Certificates
6.3.5 IPSec Settings
Navigate through Policies> VPN > IPSec Settings
The IPSec provides a method to manage authentication and data protection between multiple
crypto peers engaging in secure data transfer. It includes the Internet Security Association and
Key Management Protocol (ISAKMP)/Oakley and two IPSec
IPSec protocols: Encapsulating Security Protocol (ESP) and Authentication Header (AH). IPSec
uses symmetrical encryption algorithms for data protection. Symmetrical encryption algorithms
are more efficient and easier to implement in hardware. These algorithms need a secure method
of key exchange to ensure data protection. Internet Key Exchange (IKE) ISAKMP/Oakley
protocols provide this capability. If this is enabled, then IPSec policies are applied.
Page 65
UTM User Manual
www.allo.com Version 2.0 65
Figure 81: IPSec Settings
Click on the save button, the message will prompt your IPSec Settings are saved successfully.
Figure 82: Save the IPSec Settings
6.3.6 IPSec Policies
Navigate through Policies> VPN > IPSec Policies
Policy settings tab:
IPSec Modes
IPSec has the following two modes of forwarding data across a network:
Tunnel mode
Transport mode
Each differs in its application as well as the amount of overhead added to the passenger packet.
These modes are described in more detail in the next two sections.
Tunnel Mode
Page 66
UTM User Manual
www.allo.com Version 2.0 66
It works by encapsulating and protecting an entire IP packet. Because tunnel mode encapsulates
or hides the IP header of the pre-encrypted packet, a new IP header is added so that the packet
can be successfully forwarded. The encrypting devices themselves own the IP addresses used in
this new header.
It can be configured with either or both IPSec protocols (ESP and AH). Tunnel mode results in
additional packet expansion of approximately 20 bytes because of the new IP header.
Tunnel mode is widely considered more secure and flexible than transport mode. IPSec tunnel
mode encrypts the source and destination IP addresses of the original packet, and hides that
information from the unprotected network.
Figure 83: Policy Settings
Enable/Disable: If checked, then this policy is deployed
Name: Enter the Policy name to create IPSec Policy
Mode: User can select different modes p2p / Road warrior depending on these 2, tunnels and
transport can be selected
Local gateway: Gateway IP of the device
Local network: Network behind the gateway need to be accessed. Eg: 192.168.0.0/24
Page 67
UTM User Manual
www.allo.com Version 2.0 67
Remote gateway: user can configure the Remote gateway IP.
Remote network: Remote gateway to be accessed. Eg: 192.168.1.0/24
IKE (Internet Key Exchange)
To implement a VPN solution with encryption, periodic changing of session encryption keys is
necessary. Failure to change these keys makes the VPN susceptible to brute force decryption
attacks. IPSec solves the problem with the IKE protocol, which makes use of two other protocols
to authenticate a crypto peer and to generate keys. IKE uses a mathematical algorithm called a
Diffie-Hellman exchange to generate symmetrical session keys to be used by two crypto peers.
IKE also manages the negotiation of other security parameters such as the data to be protected,
the strength of the keys, the hash methods used, and whether the packets are protected from
anti-replay. ISAKMP normally uses UDP port 500 as both the source and destination port.
Figure 84: Create IPSec Policy-IKE
Exchange Mode: Main and aggressive mode is sustained.
IKE Fragmentation: User can either enable or disable the Fragmentation.
ESP fragmentation: User can configure the ESP fragmentation.
Lifetime: Time after the renegotiation of phase 2 happens
Encryption Algorithm: Encryption algorithm used during phase 1 negotiation
Page 68
UTM User Manual
www.allo.com Version 2.0 68
Hash Algorithm: User can select either MD5 or SHA1 algorithm from the dropdown menu.
Authentication: Supports 4 types of authentication and depending of authentication selected
need to configure the field
IPSec
Figure 85: Create IPSec Policy-IPSec
Transport: can use AH/ESP mode.
AH (Authentication Header)
The AH protocol (IP protocol 51) forms the other part of IPSec. It does not encrypt data in the
usual sense, by hiding the data but it adds a tamper-evident seal to the data. It also protects the
non-mutable fields in the IP header carrying the data, which includes the address fields of the IP
header.
The AH protocol should not be used alone when there is a requirement for data confidentiality.
ESP (Encapsulating Security Protocol)
Page 69
UTM User Manual
www.allo.com Version 2.0 69
The ESP header (IP protocol 50) forms the core of the IPSec protocol. This protocol, in
conjunction with an agreed-upon set of security Parameters or transform set, protects data by
rendering it indecipherable. This protocol encrypts the data portion of the packet only and uses
other protections (HMAC) for other protections (data integrity, anti-replay, and man-in-the-
middle). Optionally, it can also provide for authentication of the protected data.
Encryption Algorithm: User can select the available encryption methods.
Authentication Algorithm: User can select the available authentication algorithm.
Lifetime: User can configure the lifetime for the configured IPSec tunnel. If the lifetime configure
expires the tunnel become inactive.
Network:
This should be configured if in Policy Settings->Road warrior mode is selected
Figure 86: Create IPSec Policy-Network
Client IP Pool: User can assign IP Pool for clients. E.g.: 10.0.0.3-10.0.0.35
Client Routes: User can specify the client routes. E.g.:10.0.0.0/255.255.255.0
Page 70
UTM User Manual
www.allo.com Version 2.0 70
DNS: User can configure the DNS server for IPSec Policy. E.g.: 10.0.0.1
WIN: User can configure the WIN server for IPSec Policy.E.g.:10.0.0.254
Pfs Group: User can select the Pfs group value from the dropdown menu.
Advanced
Figure 87: Create IPSec Policy-Advanced
Enable compression: deflate is a compression algorithm used to compress traffic
Nat Traversal: This feature can be enabling or disable by selecting viable options.
6.4 Web Proxy
Navigate through Policies> Web Proxy
Web proxy is a caching proxy for the Web supporting HTTP, HTTPS. It reduces bandwidth and
improves response times by caching and reusing frequently-requested web pages. Web proxy
has extensive access controls and makes a great server accelerator.
Page 71
UTM User Manual
www.allo.com Version 2.0 71
6.4.1 Proxy Configuration
Navigate through Policies> Web Proxy> Proxy Configuration
Figure 88: Web Proxy
Proxy Mode: We have two modes: Transparent and Explicit.
Transparent proxy: A transparent proxy server is also a caching, server but the server is
configured in such a way that it eliminates the client side (browser side) configuration. Typically
the proxy server resides at the gateway and intercepts the WWW requests (port 80, 443 etc.)
from the clients and fetches the content for the first time and subsequently replies from its local
cache. The name Transparent is due to the fact that the client doesn't know that there is a proxy
server which mediates their requests.
Explicit proxy: A regular caching proxy server is a server which listens on a separate port (e.g.
3128) and the clients (browsers) are configured to send requests for connecting to that port. So
the proxy server receives the request, fetches the content and stores a copy for future use. So
next time when another client requests for the same webpage the proxy server just replies to
the request with the content in its cache thus improving the overall request-reply speed.
Port: It specifies the HTTP port for web proxy.
Page 72
UTM User Manual
www.allo.com Version 2.0 72
Enable logging: This specifies where to log the web proxy logs. We have three types:
o None: any logging.
o File: Log to files in the device, which in turn can he seen in web filter reports page.
o Syslog: Log to another remote system by enabling logging in device settings option.
Enable HTTPS proxy: It specifies whether to enable HTTPS proxying.
HTTPS proxy port: It specifies the HTTPS port for web proxy.
Certificate to be used for proxy signing: It provides a list of self signed SSL certificates for
HTTPS proxy.
SSL Control: It specifies the versions of SSL supported in web proxy. By default all versions are
enabled, i.e.., Auto. Other SSL versions are SSLv2 (Secure Socket Layer version 2), SSLv3 and
TLSv1 (Transport Layer Security version 1).
Enable Caching: It specifies where to enable caching when secondary device is employed.
Cache Size: It specifies how much size of caching can be done on secondary device.
Proxy Hostname: It specifies the hostname for web proxy. By default, device hostname is used
for proxy.
Append Domain Name: It specifies the domain name for proxy. Eg. allo.com
Proxy Admin Email: It specifies the email id of admin, who will receive mail in case cache dies.
Authentication: It specifies the authentication scheme used when the proxy is in explicit mode.
Authentication schemes:
Digest authentication scheme: In this scheme, the user is authenticated based username and
password added in Users(Policies->Users) and the admin has to configure User policies(Policies-
>Firewall->User Policies) to block/allow users based on web filter objects and web filter options.
Page 73
UTM User Manual
www.allo.com Version 2.0 73
6.4.2 Web filter blocking page
Navigate through Policies> Web Proxy> Web filter blocking page
Figure 89: Web filter blocking page
Error page selection: It specifies the error page to be displayed when user accesses are denied
sites. It has Default and Custom. By default, an error page will be displayed from web proxy
standard error page depending on the language selected in 'Error language in' where as in
custom; error page will be displayed upon the user entered text in the text area.
Error language in: It specifies in which language the error page should be exhibited. It will be
enabled only in Default error page selection.
6.4.3 User Authentication
Navigate through Policies> Web Proxy> User Authentication
Authentication interval: It specifies how long the authentication scheme should be valid for the
users. After the specific interval of time, the user is again prompted for authentication. Interval
range is 10 – 1440(mins).
Page 74
UTM User Manual
www.allo.com Version 2.0 74
Figure 90: User Authentication
6.4.4 Web Cache Management
Navigate through Policies> Web Proxy> Web Cache Management
Clear web cache: It specifies to clear the web cache contents present on secondary device.
Figure 91: Web Cache Management
Page 75
UTM User Manual
www.allo.com Version 2.0 75
6.4.5 External Proxy
Navigate through Policies> Web Proxy> External Proxy
Figure 92: External Proxy
Use External Proxy: It specifies to use the external proxy which is running on a remote system.
Proxy IP: It specifies the remote system IP address where the proxy is running. Eg. 10.0.0.5
HTTP Port: It specifies the HTTP port of external proxy on the remote system.
Enable HTTPS Port: It specifies whether to enable HTTPS proxy form external proxy.
HTTPS Port: This will be used when we enable HTTPS Port option. It specifies the HTTPS port of
external proxy.
6.5 Anti Virus
Navigate through Policies> Antivirus
Anti virus is computer software/Program used to prevent, detect and remove malicious
software.
Internet can be a dangerous place filled with malware of various flavors. Currently, the malware
that is most common in the Internet, in descending order, is Trojan horses, viruses, worms,
adware, back door exploits, spyware and other variations. UTM antivirus filter works by
inspecting the traffic that is transmitted through it.
Enable: It specifies whether to enable Antivirus on the device or not. It will be applied to all the
firewall policies when this option in enabled.
Page 76
UTM User Manual
www.allo.com Version 2.0 76
6.5.1 Anti Virus Settings
Navigate through Policies> Antivirus > Antivirus Settings
Figure 93: Anti Virus Settings
6.6 Users
Navigate through Policies> Users
In this section, we can create users to system by configuring username and password.
Figure 94: Create User Information
Username: It specifies the username (5 – 32 characters)
Password: It specifies the password for the current user. (Password must be about 8-32
characters with at least one numeric and one special character)
Enable/Disable: it specifies whether to allow or deny the user.
Page 77
UTM User Manual
www.allo.com Version 2.0 77
These users are used in SSLVPN Authentication and in User Policies for proxy authentication.
6.6.1 User Groups
Navigate through Policies> Users > User Groups
We can create user groups as set of users. It provides a list of users in the system, in which we
can configure which user can be selected from the group.
Figure 95: Create User Groups
User Group Name: Is specifies the user group name which is used in system scheme. (max. 16
characters)
These user groups are used in SSLVPN Authentication and in User Policies for proxy
authentication.
Page 78
UTM User Manual
www.allo.com Version 2.0 78
7. Status Information
7.1 Interfaces
Navigate through Status Info > Interfaces
UTM Interfaces demonstrate interface’s name, IP address and their Link status. User can Set,
Update and refresh the interface Page.
Figure 96: Interfaces
7.2 DHCP leases
Navigate through Status Info > DHCP Leases
It is used to view all current DHCP leases, including IP address, MAC address, hostname, lease
start and end time, and the expires in.
MAC & IP Address: It shows MAC address of connected host (IP) to DHCP Server and IP address
obtained from DHCP server.
Expires In: It demonstrates the length of time over, which IP address will lose from DHCP host
Page 79
UTM User Manual
www.allo.com Version 2.0 79
Figure 97: DHCP Leases
7.3 Firewall
7.3.1 Connection Statistics
Navigate through Status Info > Firewall > Connection Statistics
It shows UTM Firewall’s Rx/Tx packets & their packet errors, packets dropped values and packet
collisions. User can Set, Update and refresh Page. It shows list of interface names of UTM.e.g.
eth0, eth1
Page 80
UTM User Manual
www.allo.com Version 2.0 80
Figure 98: Connection Statistics
7.3.2 Connection info
Navigate through Status Info > Firewall > Connection Info
The Connection information page shows source IP, Source port, destination IP and port,
Connection status, Flow, Tx/Rx packets with size in bytes. It also shows connection Status, Flow.
The user can search particular log and even delete the unwanted connection log.
Figure 99: Connections Information
7.3.3 Bandwidth Usage per IP
Navigate through Status Info > Firewall > Bandwidth Usage per IP
It shows bandwidth usage per IP with Upstream& Downstream of both TCP&UDP statuses.
Page 81
UTM User Manual
www.allo.com Version 2.0 81
Figure 100: Bandwidth Usage per IP
7.4 System Log
Navigate through Status Info > System Log
System logs shows logs with messages of particular module and logs time stamps.
User can download the System Logs. User also Update & Refresh the page refresh interval.
Particular log can search by making use of Search field.
Figure 101: System Log
The System log page shows the time stamp logs, module name from which alert triggered and
log generated from any module.
Page 82
UTM User Manual
www.allo.com Version 2.0 82
7.5 IPS Alerts
Navigate through Status Info > IPS Alerts
It shows alerts generated by the IPS engine with signature ID, Signature category and alert
message. IPS alert shows its Time Stamp information at which alert got triggered, Source IP &
Port, Destination IP& Port and Type of protocol whether it is TCP or UDP.
The user can search particular alert using Search field. User can set & Update refreshes interval
and Download IPS alert for further analysis.
Figure 102: IPS Alerts
7.6 SSLVPN Client Status
Navigate through Status Info > SSLVPN Client Status
It read the client connection details which is connected to the SSLVPN Server Gateway. It shows
connected VPN clients to the VPN server with the client username, Client real address, and
Client virtual address, Connected Since, Byte it has received and sent.
SSLVPN client status gives you an idea about the user who connected to the VPN server, the IP
address for both real customers and Virtual customers. Also the duration of the connection
received and transferred bytes.
Page 83
UTM User Manual
www.allo.com Version 2.0 83
Figure 103: SSLVPN Client Status
7.7 SSLVPN P2P Status
Navigate through Status Info > SSLVPN P2P Status
It shows the list of SSLVPN P2P gateways connecting.
Figure 104: SSLVPN P2P Status
7.8 IPSec Status
Navigate through Status Info > IPSec Status
IPSec Status shows the list of clients connected to IPSec with IP destination of the Local gateway,
the IP address of remote gateway, transport type, mode of connection and connection state. In
UTM, an algorithm is a mathematical procedure that manipulates data to encrypt and decrypt it.
Created On designates the time at which connection established and byte transacted counts in
bytes.
Page 84
UTM User Manual
www.allo.com Version 2.0 84
Figure 105: IPSec Settings
7.9 Service Status
Navigate through Status Info > Service Status
It shows UTM important services running/Stopped status with description. The user can restart
the stopped/running status and user can set and update refresh interval. The service status page
indicates service name, description name of services and connection status.
Page 85
UTM User Manual
www.allo.com Version 2.0 85
Figure 106: Service Status
Page 86
UTM User Manual
www.allo.com Version 2.0 86
8. Diagnostics
8.1 Diagnostics Report
The diagnostics page will allow the administrator to gather the troubleshooting logs which will
help allo Support team in debugging any issues faced with UTM deployment setup.
To run the utility on the device, the administrator needs to click the ‘Run diagnostics’ button.
The device will run the diagnostics task in the backend and display the results once the task is
complete. The administrator can download the reports by clicking the ‘Get Report’ button and
send the report to allo Support team ( Note: You can submit through support ticket:
http://support.allo.com
Figure 107: Diagnostics Report
Figure 108: Download Diagnostics File
Page 87
UTM User Manual
www.allo.com Version 2.0 87
8.2 Ping
Navigate through Diagnostics > Ping
The administrator can troubleshoot the network connectivity issues with running ping from the
UTM device. The administrator needs to enter the IP address that needs to be pinged from the
UTM appliance/ping count and click the ‘Ping’ button to run the task. The ping results will be
displayed in the text area once the ping task is complete.
Figure 109: Ping
8.3 Trace Route
Navigate through Diagnostics > Traceroute
The administrator can troubleshoot the network connectivity issues with running a trace route
from the UTM device.
The administrator needs to enter the IP address, which the route needs to be traced from the
UTM appliance/hop count and click the ‘Trace route’ button to run the task.
The trace route results will be displayed in the text area once the trace route task is complete.
Page 88
UTM User Manual
www.allo.com Version 2.0 88
Figure 110: Trace Route
8.4 DNS Lookup
Navigate through Diagnostics > DNS Lookup
To look up a DNS address:
1. Locate the Perform a DNS Lookup section on the Diagnostics screen. In the DNS Server Name
field, enter a server name.
Click the Lookup button. The results of the lookup action are displayed in a new screen. To
return to the Diagnostics screen, click back on the browser menu bar.
Figure 111: DNS Lookup
Page 89
UTM User Manual
www.allo.com Version 2.0 89
8.5 Packet Trace
Navigate through Diagnostics > Packet Trace
It gives detailed information about the trace of packets in UTM with description message and
time stamp. User can download the packet trace for further analysis.
Figure 112: Packet Trace
Page 90
UTM User Manual
www.allo.com Version 2.0 90
9. Reports
9.1 System
It provides Simple logging information for the internal system services.
9.1.1System usage
Navigate through Reports > System > System usage
It shows the CPU usage of device during last 1 minute and records it in the graph of CPU usage
vs. time in seconds.
Figure 113: System Usage
9.2 Firewall
A real-time view of the firewall logs with some filtering options.
9.2.1 Internet Usage
Navigate through Reports > Firewall > Internet usage
It shows the internet usage of IP in graph format. And also shows top 25 IP connections and their
usage of Upstream & Downstream in KB.
Page 91
UTM User Manual
www.allo.com Version 2.0 91
Figure 114: Internet Usage
9.2.2 Bandwidth Usage
Navigate through Reports > Firewall > Bandwidth usage
It shows WAN bandwidth usage in graphs.
Figure 115: Bandwidth Usage
Page 92
UTM User Manual
www.allo.com Version 2.0 92
9.3 Web filter
Navigate through Reports > Web filter
It displays the web filter log viewer running in real-time mode. User can refresh reports and go
to web filters main page.
Figure 116: Web filter
9.4 IPS Alert Reports
Navigate through Reports > IPS Alert Reports
It shows top 25 signatures hit per IP in the graph. It also shows top 25 signature categories per IP
& Top IP source alerts
Page 93
UTM User Manual
www.allo.com Version 2.0 93
Frequently Asked Questions (FAQs)
What are unified threat management (UTM) devices?
It’s an approach for security management that allows an administrator to monitor and manage a
wide variety of security-related applications and infrastructure components through a single
management console.
UTM devices combine an Intrusion Prevention System (IPS), Web filtering, Firewall and antivirus
into a single hardware platform.
What is Network Security? How UTM gives security to Network?
Network Security consists of the providers and policies adopted by a network administrator to
prevent and monitor unauthorized access, misuse, modification, or denial of a computer
network and network-accessible resources.
UTM gives security to internal network by making use of Firewall, IPS (Intrusion Prevention
System), VPN Connectivity, Layer 7 filtering, Web filtering, NAT etc.
What is Proxy? What application proxies are included?
A proxy server is a hardware or software system that acts as an intermediary between an
endpoint device and another server from that device is requesting a service. UTM supports
HTTP, SSH Proxies.
What are the advantages of Unified Threat Management?
Unified Threat Management is a cost-effective solution to integrate multiple features into a
single appliance.
i. Easy to Configure
ii. Less time used for maintenance
iii. Better Performance
iv. Effective Cost
Page 94
UTM User Manual
www.allo.com Version 2.0 94
What does Unified Threat Management include?
Unified Threat Management is a cost-effective solution to integrate multiple features into a
single appliance. It includes following features:
i. Firewall
ii. IPS (Intrusion Prevention System)
iii. NAT (Network Address Translation)
iv. Web Filtering
v. VPN (SSLVPN and IPSec VPN)
vi. Layer-7 Filtering
vii. Anti-Virus
What is Layer 7 Application Control?
The online threat to productivity and security in your organization has evolved beyond simple
Web traffic. Problematic applications such as Bit Torrent, Skype, and TOP can compromise
available bandwidth and expose you to inappropriate and illegal activity.
Protocols are not identified by conventional web filters, these types of applications are difficult
to stop.
Shield UTM allows you to stop this traffic at the gateway itself.
What user authentication methods are supported by shield UTM?
I. PAP (Password Authentication Protocol)
II. CHAP (Challenge Authentication Protocol) &
III. RADIUS Authentication etc.
Page 95
UTM User Manual
www.allo.com Version 2.0 95
Glossary
Term
Definition
BPS Bit per Second
The bit/sec is a common measure of data speed for computer modems and
transmission carriers.
SSH- Secure SHell
It works on TCP protocol & Port number is 22, sometimes known as Secure
Socket Shell. It is a UNIX-based command interface and protocol for securely
getting access to a remote computer.
HTTP -Hyper Text
Transport Protocol
It works on TCP protocol & Port number is 80. The Hypertext Transfer
Protocol (HTTP) is an application protocol for distributed, collaborative,
hypermedia information systems. HTTP is the foundation of data
communication for the World Wide Web. Hypertext is structured text that
uses logical links (hyperlinks) between nodes containing text.
HTTPS -Hyper Text
Transport Protocol
over Secure Socket
Layer
It stands for Hypertext Transfer Protocol Secure, makes it more difficult for
hackers, the NSA, and others to track users. The protocol makes sure the
data isn't being transmitted in plain-text format, which is much easier to
eavesdrop on.
VPN -Virtual Private
Networks
VPN is a network that is constructed by using public wires usually the
Internet to connect to a private network, such as a company's internal
network. There are a number of systems that enable you to create networks
using the Internet as the medium for transporting data.
IPSec -Internet
Protocol Security
It is a protocol suite for securing Internet Protocol (IP) communications by
authenticating and encrypting each IP packet of a communication session.
SSLVPN -Secure
Socket Layer Virtual
Private Network
This is a form of VPN that can be used with a standard Web browser. In
contrast to the traditional Internet Protocol Security (IPSec) VPN, an SSL VPN
does not require the installation of specialized client software on the end
user's computer.
NTP - Network
Timing Protocol
It is a networking protocol for clock synchronization between computer
systems over packet-switched, variable-latency data networks.
SNMP- Simple
It is an "Internet-standard protocol for managing devices on IP networks".
Page 96
UTM User Manual
www.allo.com Version 2.0 96
Term
Definition
Network
Management
Protocol
Devices that typically support SNMP include routers, switches, servers,
workstations, printers, modem racks and more.
DNS Domain Name
Server
DNS is the Internet's equivalent of a phone book. They maintain a directory
of domain names and translate them to Internet Protocol (IP) addresses.
This is necessary because, although domain names are easy for people to
remember, computers or machines, access websites based on IP addresses.
PPPoE Point-to-Point
Protocol over
Ethernet
It is a specification for connecting multiple computer users on an Ethernet
local area network to a remote site through common customer premises
equipment, which is the telephone company's term for a modem and similar
devices.
PAP Password
Authentication
Protocol
It’s an authentication protocol that uses a password. PAP is used by Point to
Point Protocol to validate users before allowing them access to server
resources. Almost all network operating system remote servers support PAP.
CHAP- Challenge
Handshake
Authentication
Protocol
In computing, it authenticates a user or network host to an authenticating
entity.
SIP-Session Initiation
Protocol
This is a signaling communications protocol, widely used for controlling
multimedia communication sessions such as voice and video calls over
Internet Protocol (IP) networks.
DHCP- Dynamic Host
Control Protocol
It is a standardized network protocol used on Internet Protocol (IP) networks
for dynamically distributing network configuration parameters, such as IP
addresses for interfaces and services.
FTP- File Transfer
Protocol
This is a standard network protocol used to transfer computer files from one
host to another host over a TCP-based network, such as the Internet. FTP is
built on client-server architecture and uses separate control and data
connections between the client and the server.
Page 97
UTM User Manual
www.allo.com Version 2.0 97
Term
Definition
TFTP- Trivial File
Transfer Protocol
It’s a simple, lock-step, file transfer protocol which allows a client to get
from or put a file onto a remote host. One of its primary uses is in the early
stages of nodes booting from a Local Area Network.
SMTP - Simple Mail
Transfer Protocol
A protocol for sending e-mail messages between servers. Most e-mail
systems that send mail over the Internet use SMTP to send messages from
one server to another; the messages can then be retrieved with an e-mail
client using either POP or IMAP.
SSL - Secure Socket
Layer
It is the standard security technology for establishing an encrypted link
between a web server and a browser. This link ensures that all data passed
between the web server and browsers remain private and integral.
IP - Internet Protocol
It is a set of rules governing the format of data sent over the Internet or
other network.
The Internet Protocol (IP) is the method or protocol by which data is sent
from one computer to another on the internet. Each computer (known as a
host) on the Internet has at least one IP address that uniquely identifies it
from all other computers on the Internet.
MAC - Media Access
Control
Media Access Control layer is one of two sub layers of the Data Link Control
layer and is concerned with sharing the physical connection to the network
among several computers.
ICMP - Internet
Control Message
Protocol
This is one of the main protocols of the Internet Protocol Suite. It is used by
network devices, like routers, to send error messages indicating, for
example, that a requested service is not available or that a host or router
could not be reached.
IMAP- Internet
Message Access
Protocol
It is a protocol for e-mail retrieval and storage.
POP3- Post office
Protocol version 3
This standard protocol for retrieving e-mail. The POP3 protocol controls the
connection between a POP3 e-mail client and a server where e-mail is
stored. The POP3 service uses the POP3 protocol for retrieving e-mail from a
Page 98
UTM User Manual
www.allo.com Version 2.0 98
Term
Definition
mail server to a POP3 e-mail client.
TCP - Transmission
Control Protocol
It is a standard that defines how to establish and maintain a network
conversation via which application programs can exchange data. TCP works
with the Internet Protocol (IP), which defines how computers send packets
of data to each other. Together, TCP and IP are the basic rules defining the
Internet.
UDP - User
datagram protocol
UDP is a communications protocol that offers a limited amount of service
when messages are exchanged between computers in a network that uses
the Internet Protocol (IP). UDP is an alternative to the Transmission Control
Protocol (TCP) and, together with IP, is sometimes referred to as UDP/IP).
TCP/IP-Transmission
Control Protocol/
Internet Protocol
TCP/IP is the suite of communications protocols used to connect hosts on
the Internet. TCP/IP uses several protocols, the two main ones being TCP
and IP.
VLAN - Virtual Local
Area Network
A VLAN has the same attributes as a physical local area network (LAN), but it
allows for end stations to be grouped together more easily even if they are
not on the same network switch. VLAN membership can be configured
through software instead of physically relocating devices or connections.
LAN - Local Area
Network
It is a group of computers and associated devices that share a common
communications line or wireless link. Typically, connected devices share the
resources of a single processor or server within a small geographic area.
WAN - Wide Area
Network
It’s a geographically dispersed telecommunications network. The term
distinguishes a broader telecommunication structure from a local area
network (LAN).
VIP - Virtual Internet
Protocol
A virtual IP address (VIP or VIPA) is an IP address that doesn't correspond to
an actual physical network interface (port). Uses for VIPs include Network
Address Translation (especially, One-to-many NAT), fault-tolerance, and
mobility.
Page 99
UTM User Manual
www.allo.com Version 2.0 99
Loading...