Page 1
ALL0368
ALL0368
Quick Install Guide
Page 2
ALL0368
Table of Contents
1. Install ALL0368 .............................................................................................................................................................................. 3
2. Using Easy Setup Wizard to Configure ALL0368 ............................................................................................................. 6
3. Reset and Restore to Factory Default Setting ................................................................................................................... 8
ii
Page 3
ALL0368
1. Install ALL0368
Follow the below procedure to install ALL0368:
1) Attach the mounting bracket to the wall or ceiling using the provided wall/ceiling
mounting hardware kit.
2) Connect Category 5e Ethernet cable to LAN1 port of ALL0368 and connect power
adapter to DC-IN port of ALL0368 (or LAN1 port connects to PoE switch via Category 5e
Ethernet cable).
3) Fix ALL0368 on the bracket and lock the L-TYPE (as shown in figure 1). Then you
complete the installation.
3
Page 4
The status of the ALL0368 LEDs:
LED Color Status
ALL0368
WiFi Green Wireless is active
LAN1 Green LAN1 port connected to another device via Ethernet cable
Green
LAN2 port connected to another device via Ethernet cable
LAN2
Orange
LAN2 port connected to another PoE device
4
Page 5
ALL0368
You need Access Point Controller (ALL0360) to configure ALL0368, so please using Ethernet
cable to connect to the LAN port of Access Point Controller (ALL0360) after installing
ALL0368, then you can configure ALL0368.
5
Page 6
ALL0368
2. Using Easy Setup Wizard to Configure ALL0368
Start your web browser and enter the default address http://192.168.1.1 then enter admin
for both User name and Password to access Access Point Controller.
Access Point Controller can use one interface (WEB UI) to configure multiple access points
concurrently. To configure group settings and to maintain devices, including wireless
settings, importing configuration file, upgrading firmware and restarting devices etc. And
you also can observe the connection status of wireless access points and wireless status
through WEB UI.
The Easy Setup Wizard feature in Access Point Controller helps user use several simple
steps to configure Local AP. Follow the wizard to enter the SSID and password that you
want.
6
Page 7
ALL0368
When you finished the Easy Setup Wizard, access point will restart automatically to commit
the settings and the access point will apply the wireless settings.
To configure other settings, please refer to the User Manual of Access Point Controller for
further instructions.
7
Page 8
ALL0368
3. Reset and Restore to Factory Default Setting
When the device is power-on, press Reset button for 5 seconds, LAN and WLAN LEDs will
blink and then release Reset button. The device will restart.
If press Reset button over 10 seconds, LAN and WLAN LEDs will blink quickly and then
release Reset button. The device will restore to factory default setting.
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
8
Page 9
ALL0368
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
This device and it's antennas(s) must not be co-located or operating in conjunction with any
other antenna or transmitter except in accordance with FCC multi-transmitter product
procedures.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
9
Loading...