Allnet ALL02300N User Manual

ALL0300N 300M Wireless Broadband Router

ALL02300N

300M Wireless-N Broadband Router

Ma

Manual

1

ALL0300N 300M Wireless Broadband Router

Copyright Statement

ALLNET is the registered trademark of ALLNET GmbH. All the products and product names
mentioned herein are the trademarks or registered trademarks of their respective holders.
Copyright of the whole product as integration, including its accessories and software,
belongs to ALLNE T GmbH. Without the permission of ALLN ET GmbH, any individual or party
is not allowed to copy, plagiarize, reproduce or translate it into other languages.

All the photos and product specifications mentioned in this manual are for references only.
Upgrades of software and hardware may occur, and if there are changes, ALLNET is not
responsible for notifying in advance. If you would like to know more about our product
information, please visit our website at http://www.allnet.de

2

ALL0300N 300M Wireless Broadband Router

Contents

CHAPTER 1 PRODUCT INTRODUCTION ...................... 1

1.1 PACKAGE CONTENTS ............................. 1

1.2 LED INDICATORS AND PORT DESCRIPTION ............. 1

CHAPTER 2 PRODUCT INST ALLA TI ON ........................ 4

CHAPTER 3 HOW TO CONFIGURE TO ACCESS THE INTERNET

.................................................................................................. 5

3.1 HOW TO SET THE NETWORK CONFIGURATIONS ............ 5

3.2 LOG IN TO THE ROUTER .......................... 9

3.3 FAST INTERNET ACCESS ......................... 10

3.4 FAST ENCRYPTION ............................. 11

CHAPTER 4 ADVANCED SETTINGS .............................. 12

4.1 SYSTEM STATUS ............................... 12

4.2 WAN SETTINGS ............................... 13

4.3 LAN SETTINGS ............................... 16

4.4 DNS SETTINGS ............................... 16

4.5 WAN MEDIUM TYPE............................. 17

4.6 BANDWIDTH CONTROL ............................ 18

4.7 TRAFFIC STATISTICS ........................... 21

CHAPTER 5 WLAN SETTINGS ........................................ 22

5.1 WIRELESS BASIC SETTINGS ....................... 22

5.2 WIRELESS SECURITY SETTINGS .................... 25

5.2.1 WPS SETTINGS ............................. 25

5.2.2 WPA- PSK ................................ 26

5.2.3 WPA2- PSK ............................... 26

5.3 WIRELESS ACCESS CONTROL ....................... 27

5.4 CONNECTION STATUS ............................ 27

CHAPTER 6 DHCP SERVER ............................................. 28

6.1 DHCP SERVER ................................ 28

6.2 DHCP CLIENT LIST ............................ 28

3

ALL0300N 300M Wireless Broadband Router

CHAPTER 7 VIRTUAL SERVER ...................................... 30

7.1 PORT RANGE FORWARDING ........................ 30

7.2 DMZ SETTINGS ............................... 32

7.3 UPNP SETTINGS .............................. 32

CHAPTER 8 SECURITY SETTINGS ............................... 33

8.1 CLIENT FILTER SETTINGS ....................... 33

8.2 MAC ADDRESS FILTER .......................... 34

8.3 URL FILTER SETTINGS ......................... 36

8.4 REMOTE WEB MANAGEMENT ........................ 38

CHAPTER 9 ROUTING SETTINGS ................................. 39

9.1 ROUTING TABLE ............................... 39

9.2 STATIC ROUTING .............................. 39

CHAPTER 10 SYSTEM TOOLS ........................................ 40

10.1 TIME SETTINGS .............................. 40

10.2 DDNS .................................... 40

10.3 BACKUP/RESTORE ............................. 41

10.4 RESTORE TO FACTORY DEFAULT ................... 42

10.5 UPGRADE ................................... 43

10.6 REBOOT THE ROUTER ........................... 43

10.7 PASSWORD CHANGE ............................ 44

10.8 SYSLOG ................................... 44

10.9 LOG OUT ................................... 44

APPENDIX 1 GLOSSARY .................................................. 45

APPENDIX 2 PRODUCT FEATURES .............................. 46

APPENDIX 3 FAQ ............................................................... 47

APPENDIX 4 CLEAR WIRELESS CONFIGURATION . 49

APPENDIX 5 REGULATORY INFORMATION.............. 51

CE DECLARATION OF CONFORMITY…………..…52

4

11N Wireless Broadband Router User Guide

Chapter 1 Product Introduction

Thank you for purchasing the ALLNET Wireless N Broadband Router!
This easy-to-use router provides simple configuration interface which enables you to configure it with
ease. It is based on the latest IEEE802.11n standard, and is backward compatible with devices of
IEEE802.11b/g standards.
The ALLNET wireless router，including router, wireless AP, four-port switch and firewall in one，provides
powerful online monitor functio n and support s UR L filter and MAC filter. With WDS fun ction, i t can r epeat
and amplify wireless signals so as to enlarge network coverage area. It truly supports UPnP and WMM
to make your audio and video smoother. With QoS function, it can efficiently distribute the downloading
rate for the clients. With s up er c ompatibility, the router can break the access limits in some areas so that
multiple computers can share the Internet access. Additionally, it supports WISP function to access to
the ISP’s wireless hotspots (this function applies only to some of the products).

1.1 Package Contents

Please verify the following items after you open the package:

 One Wireless N Broadband Router

 One Quick Installation Guide
 One Power Adapter
 One Software CD

If any of the listed items are missing or damaged, please contact the ALLNET reseller for immediate
replacement.

1.2 LED Indicators and Port Description

Panel and LED indicators show:

LED indicator description on the front panel

1

11N Wireless Broadband Router User Guide

Back panel port show

2

11N Wireless Broadband Router User Guide

Back panel port description

3

11N Wireless Broadband Router User Guide

Chapter 2 Product Installation

In this user guide, we take ALL02300N to explain the installation steps. The installation steps of other
products are similar to this one.

1. Please use only the included power adapter to power your router. (NOTE: Use of an unmatched
power adapter could cause damage to this product).

2. Please connect the router’s LAN port to your computer with an Ethernet cable as shown below.

3. Please connect your broadband line provided by your ISP to the router’s WAN port.

4. Insert the included software CD into the CD drive of your computer. After the software automatically

initiates, double click the “Setup” icon and follow the instructions to complete the installation. You can
also enter the router’s Web-based Utility to complete the configuration.

4

11N Wireless Broadband Router User Guide

Chapter 3 How to configure to access the Internet

3.1 How to Set the Network Configurations

Network Configurations under windows XP

1. Right click “My Network Places” on your computer desktop and select “Properties”.

2. Right click “Local Area Connection” and select “Properties”.

3. Select “Internet Protocol (TCP/IP)” and click “Properties”.

5

11N Wireless Broadband Router User Guide

4. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”.

Click “OK” to save the configurations.

Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as
follows:

 IP Address: 192.168.0.XXX: (XXX is a number from 2~254)
 Subnet Mask: 255.255.255.0
 Gateway: 192.168.0.1
 DNS server: You should input the DNS server address provided by your ISP. Otherwise, you can

enter 192.168.0.1. Click “OK” to save the configurations.

6

11N Wireless Broadband Router User Guide

Network Configurations under windows 7

1. Click the network icon on t he lower right corner of your computer desktop , and then click” Open

Network and Sharing Center”.

2. Click “Change adapter settings” on the lef t sid e of the w indow.

3. Right click “Local Area Connection” and select “Properties”.

7

11N Wireless Broadband Router User Guide

4. Double click” Internet Protocol Version 4(TCP/IPv4)".

5. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”.

Click “OK” to save the configurations.

Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as
follows:

8

11N Wireless Broadband Router User Guide

 IP Address: 192.168.0.XXX: (XXX is a number from 2~254)
 Subnet Mask: 255.255.255.0
 Gateway: 192.168.0.1
 DNS server: You should input the DNS server address provided by your ISP. Otherwise, you can

enter 192.168.0.1. Click “OK” to save the configurations.

3.2 Log in to the Router

1. To access the Router’s Web-based Utility, launch a web browser such as Internet Explorer or

Firefox and enter http://192.168.0.1. Press “Enter”.

2. The system will automatically choose the corresponding web language in accordance with the

Browser’s language. For example, if your Browser’s language is French, the router’s web language will
display as French.

3. If your Browser language is English or beyond the 9 languages (Arabic, French, German, Italian,

Polish, Portuguese, Russian, Spanish, Turkish), the router’s web language will be English.

9

11N Wireless Broadband Router User Guide

3.3 Fast Internet Access

Two kinds of fast access methods are provided on the router’s web-based utility: ADSL dial-up and
DHCP.
If you select ADSL dial-up, you only need to enter the access account and access password as well as
the wireless password, and then click “Ok” to complete the settings.

If you select DHCP, you only need to enter the wireless password and click “Ok” to complete the
settings.

10

11N Wireless Broadband Router User Guide

The default access method is AD SL dial-up and the access account and access password are the same
as the ADSL dial-up account and password, which you can inquire your broadband ISP. For other
access methods, please refer to WAN settings in chapter 4.The wireless password can only consist of 8
characters, the default is ALL02300N and you can modify it when necessary.

3.4 Fast Encryption

The router provides two encryption setting screens, one is simple and easy, the other is advanced (For
advanced setting, please refer to chapter 5. 2).

Simple and easy screen:

Log on to the router’s web-based utility and you may set encryption for the router. The default adopts
WPA-PSK mode and AES Algorithm. The default password is ALL02300N, as shown below.

NOTE: The wireless password can only be 8 characters in length and the default is ALL02300N,

you can modify it when necessary.

11

11N Wireless Broadband Router User Guide

Chapter 4 Advanced Settings

4.1 System Status

System status screen allows you to view the router’s WAN port status and system status.

 Connection status: It displays the router’s WAN connection status.

Disconnected: It indicates the router’s WAN port hasn’t been connected with the network cable.
Connecting: It indicates the router ’s WAN port is obtaining IP address.
Connected: It indicates the Router is well connected with the ISP.

 WAN IP：IP address obtained from ISP.
 Subnet mask: Obtained from ISP.
 Gateway: Obtained from ISP.
 DNS server: Obtained from ISP.
 Alternate DNS server: Obtained from ISP.
 Connection type: It displays your current access method.

 LAN MAC address：It display s the R oute r’s LAN MAC addre ss .
 WAN MAC address：It displays the Router’s WAN MAC Address.
 System time：It displays the system’s updated time
 Connected client ：It displays the number of the connected computers(normally it displays the

number of clients whose IP addresses obtained via DHCP server)

 Software version：It displays the Router’s software version；
 Hardware version：It displays the Router’s hardwar e v ersion.

12

11N Wireless Broadband Router User Guide

4.2 WAN Settings

Virtual Dial-up (PPPoE)

 Mode: Show your current connection mode.
 Access Account: Enter the account provided by your ISP.
 Access Password: Enter the password provided by your ISP.
 MTU: Maximum Transmission Unit. It is the size of the largest data packet that can be sent over

the network. The default value is 1492. Do NOT modify it unless necessary, but if a specific
website or web application software cannot open or be enabled, you can try to change the MTU
value to 1450, 1400, etc.

 Service Name: The connection name for current PPPOE, enter it if necessary，otherwise, leave it

blank.

 AC Name: The service name, enter it if necessary，otherwise, leave it blank.
 Connect Automatically: Connect automatically to the Internet after rebooting the system or

connection failure.

 Connect on Demand: Re-establish your connection to the Internet after the specific time (Max

Idle Time). Zero means you are connected to the Internet all times. Otherwise, enter the minutes
to be elapsed before you are disconnect ed from the Internet.

 Connect Manually: Connect to the Internet by users manually.
 Connect on Fixed Time: Connect to the Internet during the time you fix automatically.

NOTE:
The “Connect on Fixed Time” goes into effect only when you have set the current time in “Time
settings” from “System tools”.

13

11N Wireless Broadband Router User Guide

Static IP

If your ISP provides you the static IP, please choose static IP, and you need to enter the IP address,
subnet mask, gateway, DNS server and alternate DNS server provided by your ISP or network
administrator。

 Mode: Show your current connection mode.
 IP address: Enter the WAN IP address provided by your ISP. If you are not clear, please inquire

your local ISP.

 Subnet mask: Enter the WAN Subnet Mask provided by your ISP. Generally it is 255.255.255.0

。

 Gateway: Enter the Gateway provided by your ISP. If you are not clear, please inquire your local

ISP.

 DNS server: Enter the necessary DNS server provided by your ISP.
 Alternate DNS server: Enter the second DNS address if your ISP provides, which is optional.

Dynamic IP (Via DHCP)

If your connection mode is Dynamic IP, it means every time you access the Internet, you will get a
different IP. You don’t need to enter any parameters in this mode, just Click “Ok” to finish the settings.

14

PPTP

11N Wireless Broadband Router User Guide

 Mode: Show your current connection mode.
 PPTP server address: T he IP address or domain name of the destinati on se rver and it is used to

specify the destination address which needs for PPTP connection.

 Username/Password: Used to validate identity when connecting to the PPTP server.
 Address mode: Set the router’s IP address mode, you can select either “Dynamic” or “Static”. If

your ISP doesn’t provide the IP address, please select “Dynamic”.

 IP address: Please enter the IP address provided by your ISP, inquire your local ISP if you are

not clear.

 Subnet mask: Please enter the subnet mask provided by your ISP ,generally its 255.255.255.0
 Gateway: Please enter the gateway provided by your ISP, inquire your local ISP if you are not

clear.

All the above parameters are provided by ISP.

L2TP

 Mode: Show your current connection mode.
 L2TP server address: The IP address or domain name of the destination server and it is used to

specify the destination address which needs for L2TP connection.

 Username/Password: Used to validate identity when connecting to the L2TP server.
 Address mode: Set the router’s IP address mode, you can select either “Dynamic” or “Static”. If

your ISP doesn’t provide the IP address, please select “Dynamic”.

 IP address: Please enter the IP address provided by your ISP, inquire your local ISP if you are

not clear.

15

11N Wireless Broadband Router User Guide

 Subnet mask: Please enter the subnet mask provided by your ISP ,generally its 255.255.255.0
 Gateway: Please enter the gateway provided by your ISP, inquire your local ISP if you are not

clear.

All the above parameters are provided by ISP.

4.3 LAN Settings

Click “Advanced settings” – LAN settings to en ter the following screen.

 LAN MAC address: The Router’s LAN MAC address, which is unchangeable.
 IP address: The Router’s LAN IP address (not your PC’s IP address).The default value is

192.168.0.1; you can change it when necessary.

 Subnet mask: The Router’s LAN subnet mask. The default value is 255.255.255.0

NOTE:

Once you modify the IP address, you need to remember it for next time you log in to the web-based
utility.

4.4 DNS Settings

DNS stands for Domain Name System (or Service).

 DNS setting: Select to enable the DNS server.
 Primary DNS address: Enter the necessary address provided by your ISP.
 Alternate DNS address: Enter the second DNS address if your ISP provides, which is optional.

NOTE:

After the settings are completed, reboot the device to activate the modified settings.

16

11N Wireless Broadband Router User Guide

4.5 WAN Medium Type

Wired WAN and wireless WA N

NOTE: This function applies only to some of the products.

Wired WAN: In this mode, the cable is directly connected to the WAN port. Wired WAN is the default
mode.
Wireless WAN: Enable this mode if your ISP provides you wireless connection service or you want to
use it to amplify wireless signals.
SSID: SSID (Service Set Identifier) is the identity of the wireless device. You can only access to the ISP’
network by entering the correct SSID, namely the SSID of the ISP’s wireless device. You can click the
“Open scan” button to let the router automatically search the ISP’s available SSID. The SSID can also
be the SSID of the superior wireless device when using wireless bridge.
MAC: To connect to the ISP’s wireless device, you need to know the device’s MAC address. You can
click the “Open scan” button to l et t he router automatically search the wireless device’ s MAC or superior
wireless device’s MAC .
Channel: The wireless device’s co mmunication chan nel. You must select the sam e chan nel as t he ISP ’ s
wireless device to enable their communications. It can also be scanned by clicking the “Open scan”
button.
Security mode: When the ISP wireless device is secured, the access device should set the same
security mode, encryption mode and key as the ISP’ wireless device.

For example

If your ISP wireless device’s SSID is “wireless”, then just enter the ISP’s SSID, wireless MAC address,
and channel respectively into the corresponding fields of the above picture. If the ISP device is secured,
please set your router’s encryption type the same as the ISP device’s .Or you can click the “Open scan”
button to let the router automatically fill in the SSID, Channel and wireless MAC. After saving, come
back to the WAN Setting screen to select the corresponding WAN connection type to complete the
settings (For example, if your ISP wireless device’s connection type is dynamic IP, just select DHCP).

17

11N Wireless Broadband Router User Guide

4.6 Bandwidth Control

Bandwidth control is used to limit the communication traffic of LAN computers when accessing the
Internet. It can simultaneously control maximum of 254 PCs' traffic. In addition, IP address range
configuration is supported.

 Enable Bandwidth Control: To enable or disable the internal IP bandwid th con trol. The defa ult i s

disabled.

 IP Address: The IP address range of the hosts whose traffic has been cont rolled. It can be a

single IP address or IP address range.

 Upload/Download: To specify the traffic heading way for the selected IP addresses: upload or

download.

 Bandwidth Range: The maximum and minimum upload/download data traffic of the hosts in

specified IP range. The unit is KByte/s. The uplink of upload and download can not exceed the
WAN port bandwidth limita tion range.

 Enable: To enable the current edited rule. Otherwise, the rule will not go into effect.
 Add to list: After you edit the rule, click the “add to list” button to ad d the cu rre nt rule to the rul e

list.
Here we take 2Mbps bandwidth as an example. Theoretically, the biggest downloading rate for 2Mbps
bandwidth is 2Mbps=256KByte/s, and the biggest uploading rate is 512kbps=64KByte/s

Example 1

If you want to set the d ownloa d rate of th e com puter at th e IP a ddress of 192 .168. 0.100 as 80- 90KBy te/s,
upload rate as 10-15KByte/s, first add one upload rule as shown in the picture below:

18

11N Wireless Broadband Router User Guide

1. Enter 192.168.0.100 in the IP address field

2. Select upload in the Upload/Download field.

3. Enter 10-15 in the bandwidth range field

4. Select “Enable”

5. Click “Add to list”

6. Click “Ok” to finish the upload rule settings.

And then add a download rule as shown in the picture below.

The setting method is the same as the above.

Example 2 Set the download rate of all computers within the range of 192.168.0.2--192.168.0.254 as
100-120KByte/s, and the upload rate as 20-30KByte/s, as shown in the picture below.

19

11N Wireless Broadband Router User Guide

The setting method is the same as Examp le 1.

20

11N Wireless Broadband Router User Guide

4.7 Traffic Statistics

Traffic statistics is used to display the bandwidth that LAN PC used.

Enable T raffi c statistics: It is used to calculate the tr af fic used by the LAN com puter s. You can enable it
to calculate the traffic for you. Usually, disable it to improve the router’s data packet processing ability,
and the default is disabled. When this function is enabled, the webpage will refresh automatically every
five minutes, meanwhile, each computer’s traffic value will refresh automatically.

 IP address: the IP address of the computer whose traffic is being calculated.
 Uplink rate: the data sending speed per second, the unit is KByte/s.
 Downlink rate: the data receiving speed per second, the unit is KByte/s.
 Sent message: the number of the calculated computer’s data packets that are sent out through

the router.

 Sent Bytes: the volume of the calculated computer’s statistics that is sent out through the router
 Received message: the number of the calculated computer’s the data packets that are received

through the router .
 Received Bytes: the volume of the calculated computer’s statistics that is received through the

router.

21

11N Wireless Broadband Router User Guide

Chapter 5 WLAN Settings

5.1 Wireless Basic Settings

 Enable wireless function: Select to enable the Router’s wireless features; deselect to disable it

and all functions related with wireless are disabled.
 Wireless working mode: This router provides two kinds of working modes: Wireless Access

Point(AP) and Network Bridge (WDS)

Wireless Access Point (AP)
 Network Mode: Select one mode from the drop-down list.

11b mode：Select it if you have only Wireless-B clients in your network.
11g mode：Select it if you have only Wireless-G clients in your network.
11b/g mixed mode: Select it if you have only Wireless-B and Wireless-G clients in your

network.

11b/g/n mixed mode: Select it if you have Wireless-B, Wireless-G and Wireless-N clients in

your network.

 SSID: It is the unique name of the wireles s network and can be modified. The SSID must be

entered.
 Broadcast (SSID): Select “Enable” to enable the router’ SSID to be scannable by wireless

devices. The default is enabled. If you disable it, the wireless devices must know the SSID for

communication.

 Channel: The currently used channel by the router. Select an effective channel (from 1 to

13\Auto) of the wireless network.
 WMM Capable: Enable it to enhance the transfer performance of the wirelessly transferred

multimedia data (such as video or online playing).We recommend enabling this option if you are

22

11N Wireless Broadband Router User Guide

not familiar with WMM.

 APSD Capable: It is used for auto power-saved service. The default is disabled.
 Channel bandwidth: Select an appropriate channel bandwidth to enhance the wireless

performance. Select 20/40M when the network has 11b/g and 11n wireless clients. Select 20M

when the network has only non-11n wireless clients. Select 20/40M to promote its throughput

when the wireless network is in 11n mode.
 Extension Channel: To confirm the network’s frequency range in 11n mode.

NOTE: Some products may have primary SSID and secondary SSID options, as shown below.

Primary SSID is necessary, secondary SSID is optional.

Network Bridge (WDS) Settings

WDS (Wireless Distribution System) is used to expand wireless coverage area.

 AP MAC address: Input the MAC address of another (opposing) wireless router you want to

connect.

23

11N Wireless Broadband Router User Guide

Example: This example is to bridge two ALL02300N routers.

1. If you know the connecti ng router’s MAC address, please en ter it in to the AP MAC address fiel d and
click “Ok”.

2. You can also search for the wireless router’s signal by scanning.
a) Click “Open scan” and click the scanned signal and click the ”Ok” button on the dialog box and the
corresponding wireless MAC address will be added to the AP MAC address field automatically.

b) Click “Ok” after the MAC address is added.

24

11N Wireless Broadband Router User Guide

After finishing the above steps, you need to set the other ALL02300N router in the same way.

NOTE:
WDS feature requires both routers support this function and the SSID, channel, encryption method and
password are the same as those of the connectin g rou ter.

5.2 Wireless Security Settings

With the wireless security functi on, y ou can prev ent ot hers fr om co nnecting to y our wirel ess netw ork and
using the network resources without your consent. Meanwhile, you can also block illegal users from
intercepting or intruding your wireless network.

5.2.1 WPS Settings

WPS (Wi-Fi Protected Setting) makes it quick and easy to establish a secure connection between the
wireless clients and the router. The users only need to enter a PIN code or press WPS button on the
back panel to configure it without manually selecting an encryption method or set a key.

 WPS settings: To enable or disable WPS function. The default is “Enable”.
 WPS mode: Provide two ways: PBC (Push-Button Configuration) and PIN code.
 PBC: Sele ct the PBC and cl ick Ok, or press and hold the WPS button on the back panel of the

device for about one second. The WPS LED indicator will be flashing for 2 minutes, which means
the WPS is enabled. During this time (flashing WPS LED) , you can enable the wire less client to
implement the WPS/PBC negotiatio n betw een th em. When the WPS con nection is compl eted, t he
LED indicator will be continuously lit. To add more clients, repeat the above steps.)

 PIN: If this option is enabled, you need to enter a wireless client’s PIN code in the field and keep

the same code in the WPS client.

 Reset OOB: Press this button, the WPS client will be in an idle state, and the WPS indicator will

turn off. AP will not respond to the WPS client’s connection request and will set the security mode
as Open-None (Disable) mode.

25

11N Wireless Broadband Router User Guide

NOTE:

The use of WPS function requires the wireless adapter to support this function.

5.2.2 WPA- PSK

WPA guarantees to protect WLAN users’ dat a and only the autho rized n etwork user s can hav e access to
WLAN.

 WPA Algorithms: Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption

Standard].

 Key: Enter the pass phrase that consists of 8-6 3 ASCII characters.
 Key Renewal Interval: Set the key’s renewal per iod, which tells the device how often it should

change the dynamic keys.

5.2.3 WPA2- PSK

WPA2 (Wi-Fi Protected Access version 2) provides higher security than and WPA (Wi-Fi Protected
Access).

 WPA Algorithms: Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption

Standard].

26

11N Wireless Broadband Router User Guide

 Key: Enter the pass phrase that consists of 8-6 3 ASCII characters.
 Key Renewal Interval: Set the key’s renewal per iod, which tells the device how often it should

change the dynamic keys.

5.3 Wireless Access Control

Wireless access control is actually based on the MAC address to permit or forbid specific clients to
access the wireless network.

 MAC address filter: “Permit” indicates to allow the clients in the list to access the wireless

network, “Forbid” indicates to prevent the clients in the list from accessing the wireless network.

 Configure MAC address: Input the MAC addresses of the wireless clients to implement the filter

policy. Click “Add” to finish the MAC add operation.

 MAC Address list: Show the added MAC addresses. You can add or delete them.

5.4 Connection Status

This screen shows wireless client’s connection status, including MAC address, Channel bandwidth.

 MAC address: Shows the MAC addresses of the hosts connected to the Router.
 Bandwidth: Shows the channel bandwidth of the current con ne ct ed hosts (wireless clients).

27

11N Wireless Broadband Router User Guide

Chapter 6 DHCP Server

6.1 DHCP Server

DHCP (Dynamic Host Control Protocol) is used to assign an IP address to the computers on the
LAN/private network. When you enable the DHCP Server, the DHCP Server will allocate automatically
an unused IP address from the IP address pool to the requesting computer in premise of activating
“Obtain an IP Address Automatically”. So specifying the start and end address of the IP Address pool is
needed.

 DHCP server: Check the Enable box to enable DHCP server.
 IP pool start/end address: Enter the range of IP addresses for DHCP server distribution.
 Lease time: It indicates the valid time of the dynamic IP address which is distributed to the

DHCP client’s host computer by DHCP serv er. During this time, the server will not distribute the IP
address to any other host computer.

6.2 DHCP Client List

DHCP client list displays user computer’ IP address, MAC address, host name and other infor mation
which are assigned by the DHCP server. You can manually enter the IP and MAC address and convert
them to static assignment.

28

11N Wireless Broadband Router User Guide

 Host name: It displays the name of the computer whose IP is allocated by the DHCP server.
 IP address: Enter the IP address which needs static binding.
 MAC address: Enter the MAC address of the computer you want to bind. Click “Add” to add the

entry in the list.

 Lease time: The remaining time length of the corresponding IP address lease.

29

11N Wireless Broadband Router User Guide

7.1 Port Range Forwarding

Chapter 7 Virtual Server

 Start/End port: Enter the start/end port number which ranges the External ports used to set the

server or Internet applications.

 LAN IP: Enter the IP address of the PC which you want to set as the server.
 Protocol: Select the protocol (TCP/UDP/Both) for the application. If you are not clear about the

protocol you are using, you can select “Both”.

 Enable: Click the Enable checkbox to bring the set rule into effect.
 Delete: Clear all settings of this item.
 Well-known service port: The well-known protocol ports are listed in the drop-down list. Select

one and select a sequence number in the ID drop-down list and then click “Add”, this port will be
added automatically to the ID list. For other well known service ports that are not listed, you can
manually add them to the list.

 Add to: Add the selected well-known port to the policy ID.
For Example: You want to share some large files with your friends outside of your local area network,

however, they are too big, and it’s not convenient to transfer them. Then, you can build a FTP server on
your computer and set the router ’s port range forwarding to enable your friends to access to these files
on your computer. Suppose that your FTP server or your computer’s static IP address is 192.168.0.10,
and you wish your friends can access the server through the default port 21 and adopts TCP protocol.

30

11N Wireless Broadband Router User Guide

Please follow the steps below to configure.

1.Enter 21 in both start port and end port fields, or you can also select FTP from the well-known service
port and its port 21 will be added to the corresponding field automatically.

2. Enter 192.168.0.10 in the LAN IP column, and then select “Both” as the protocol and select “Enable”.

3. As the picture shown below.

4. Click the “Ok” button to save the settings.
And now, when your friends want to visit the FTP server, they only need to enter ftp://xxx.xxx.xxx.xxx:21
in the address field. Here, xxx.xxx.xxx.xxx means the router’s WAN IP address. For example, when y our
router’s WAN IP address is 172.16.102.89; your friends need to enter ftp://172.16.102.89:21 in the
address field.

NOTE:

If you set the service port of the v irtual serv er as 80, y ou must s et the We b management p ort on R emote
Web Management screen to be any value except 80 such as 8080. Otherwise, there will be a conflict to
disable the virtual server.

31

11N Wireless Broadband Router User Guide

7.2 DMZ Settings

The DMZ Settings screen allows one local computer to be exposed to the Internet for use of a
special-purpose service such as Internet gaming or videoconferencing. DMZ hosting forwards all the
ports at the same time to one PC.

 DMZ Host IP Address: The IP address of the LAN computer you want to set as DMZ host.
 Enable: Check to enable the DMZ host.

For example:

Set the computer at the IP add ress of 19 2.16 8.0.1 0 a s DMZ hos t to con nect an other hos t on the Int ernet
for intercommunication.

NOTE:
When the DMZ host is enabled, the firewall settings of the DMZ host will not function.

7.3 UPNP Settings

UPnP (Universal Plug and Play).With the UPnP function, the internal host can request the router to
process some special port switching so as to enable the external host to visit the resources of the
internal host.

 Enable UPnP: Click the checkbox to enable the UPnP.

NOTE:

This function goes into effe ct unde r Wind ows XP or Wind ows ME (NOTE: the sy stem sho uld integ rate or
have installed the Directx 9.0) or this function would go into effect if you have installed software that
supports UPnP.

32

11N Wireless Broadband Router User Guide

Chapter 8 Security Settings

8.1 Client Filter Settings

You can enable client filter to control LAN computers’ access to some ports of the Internet。

 Filter Mode: You can select either “Permit only” or “Forbid only”.
 Access Policy: Select one number from the drop-dow n list.
 Remark: A simple description of the configured file. You can also leave it blank.
 Start/End IP: Enter the start/end IP address.
 Port: Enter the controlled TCP/UDP protocol port. You can specify a port or port range.
 Type: Select one protocol (TCP/UDP/Both) from the drop-down list.
 Time: Select the time range of client filter.
 Date: Select the day(s) to run the access policy.
 Enable: To enable/disable the access policy (forbid/permit the packets matched with the access

policy to pass through the router.

Example1 Forbid LAN computers at the IP addresses of 192.168.0.100--192.168.0.120 to access the
Internet.

33

11N Wireless Broadband Router User Guide

Example 2 Permit LAN computer with the IP address of 192.168.0.145 to access websites during
8:00 to 18:00 from Sunday to Saturday.

8.2 MAC Address Filter

You can limit the computer’s access to Internet by MAC Address Filter.

34

11N Wireless Broadband Router User Guide

 Filter mode: You can select either “Permit only” or “Forbid only”.
 Access Policy: Select one number from the drop-dow n list.
 Remark: A simple description of the configured file. You can also leave it blank.
 MAC Address: Enter the MAC address you want to run the access policy.
 Time: Select the time range of MAC address filter.
 Date: Select the day(s) to run the access policy.
 Enable: To enable/disable the access policy (forbid/permit the packets matched with the access

policy to pass through the router).

Example 1 Forbid the computer with the MAC address of 00:0F:C9:09:FF:57 to access Internet during
8:00 to 18:00 from Monday to Friday.

Example 2 Permit the computer with the MAC address of 00:E4:A5:44:35:69 to access Internet from
Monday to Friday.

35

11N Wireless Broadband Router User Guide

8.3 URL Filter Settings

You can use URL filtering to forbid their access to certain web sit es at a specified time.

 Filter Mode: You can select either “Permit only” or “Forbid only”.
 Access Policy: Select one number from the drop-down list.
 Remark: A simple description of the configured file. You can also leave it blank.
 Start/End IP: Enter the start/end IP address.
 URL character string: Specify the text strings or keywords needed to be filtered.
 Time: Select the time range of URL filter.
 Date: Select the day(s) to run the access policy.
 Enable: To enable/disable the access policy (forbid /permit the packets matched with the access

policy to pass through the router).
Example1 Forbid all computers on LAN to access baidu.com during 8:00 to 18:00 from Monday to
Friday.

36

11N Wireless Broadband Router User Guide

NOTE:

Enter only one domain name for each access policy for one access policy can only filter one domain
name. So, if you want to filter multiple domain names, you need to set multiple access policies

37

11N Wireless Broadband Router User Guide

8.4 Remote Web Management

This section instructs how to all ow the n etw ork admini strat or to man age t he Ro uter rem otel y. If you want
to access the Router from outside of the local network, please click the checkbox after “Enable”.

 Enable: Check to enable remote web management.
 Port: The management port open to outside access. The default value is 80.
 IP Address: Specify the range of the IP addresses of the computers on the Internet for remote

management.

NOTE:

1. If you want to log in the device’s Web-based Utility via port 8080, you need to use the format of WAN
IP address: port (for example http://212.18.34.50:8080) to implement remote login.

2. If your WAN IP address starts and ends with 0.0.0.0, it means all hosts on the Internet can implement
remote Web management.

For example:

If you want to configure the computer at the IP address of 218.88.93.33 to access the router’s
web-based utility via port 8080, please set the parameters as above.

38

11N Wireless Broadband Router User Guide

Chapter 9 Routing Settings

9.1 Routing Table

This page shows the router’s core routing tabl e.

The main duty for a router is to l ook for a best p ath f or ev ery dat a p acke t, an d transf er thi s dat a p acket t o
a destination station. In order to fulfill this function, many transferring paths, i.e. routing table, are saved
in the router, for choosing when needed.

9.2 Static Routing

This screen is used to set the router ’s static routing.
A static route is a pre-determined pathway that network information must travel to reach a specific host
or network.

 Destination network IP address: The destination host or IP segment you visit.
 Subnet mask: Enter the subnet mask, generally it is 255.255.255.0
 Gateway: The entry IP address of the next router.

NOTE:

1. The gateway must be at the same net segment with the router’s LAN IP.

2. If the destination IP address is one host’ address, then the subnet mask must be 255.255.255.255.

3. If the destination IP addres s is an IP se gment, t hen it mus t mat ch with the subn et mask. For ex ample ,
if the destination IP is 10.0.0.0 then the subnet mask must be 255.0.0.0

39

11N Wireless Broadband Router User Guide

Chapter 10 System Tools

10.1 Time Settings

This section is to configure the router’s system time. You can set it manually or obtain the GMT time
from the Internet.

 Time zone: Select the time zone where you are operating the Router from the drop-down list.
 Customized time: Enter the time you wish to configure.

NOTE:

When the Router is powered off, the time settings will be lost. The router will obtain the GMT time
automatically when you next time access the Internet. Only when you connect to the Internet and obtain
the GMT time or set the time on this screen, can th e time settings in other functions (e.g. security
settings) take effect.

10.2 DDNS

The DDNS (Dynamic Domain Name System) is supported in this Router. It is used to assign a fixed host
and domain name to a dynamic Internet IP address. Every time you access the Internet, the dynamic
domain name software installed on your host will tell the ISP’S host server its dynamic IP address by
sending messages. And the server software is responsible for providing DNS service and implementing
dynamic domain name resolution.

40

11N Wireless Broadband Router User Guide

 Main features:

1. Mostly, your ISP provides a dynamic IP address and the DDNS is used to capture the

changeable IP address and match to the fixed domain. Then users can have access to the

Internet to communicate with others out side the network.

2. DDNS can help you to establish a virtual host in your home or company.

 DDNS: Click the radio button to enable or disable the DDNS service.
 Service provider: Select one from the drop-down list and click “Sign up” for registration.
 Username: Enter the username that you use to register from the DDNS provider
 Password: Enter the password that you use to register from the DDNS provider
 Domain name: Enter the effective registered domain name

10.3 Backup/Restore

On this screen, you can back up the router’s current settings or restore previous settings.

 Backup Setting:

Click the Backup button to back up the Router’s settings and select a path to save them.

Click the “Save” button to save the configuration files.
 Restore Setting:

Click the “Browse” button to select the backup files.

41

11N Wireless Broadband Router User Guide

Click the “Restore” button to restore previous settings.

10.4 Restore to Factory Default

This screen allows you to restore all settings to the factory default values.

 Restore: Click this button to restore to default settings.
 Factory default settings:

Password: NULL(the default password displays as null)

IP address: 192.168.0.1

Subnet mask: 255.255.255.0

NOTE:

After restoring to default settings, please restart the router to make the default settings effective.

42

11N Wireless Broadband Router User Guide

10.5 Upgrade

By upgrading the router’s software, you’ll get better software version and appreciated routing function.
Before upgrading, download the Router ’s software upgrade file from our website, http://www.allnet.de

 Browse: Click this button to select the upgrade file.
 Upgrade: Click this button to start the upgrading process. After the upgrade is completed, the

router will reboot automatically.

10.6 Reboot the Router

Reboot the router to make the configuration effective. The router will cut its WAN connection
automatically after rebooting.

 Reboot the router: Click this button to reboot the router.

43

11N Wireless Broadband Router User Guide

10.7 Password Change

This section is to set a new password to better secur e your router and network.

 Old password: Enter the old password.
 New password: Enter a new password.

 Confirm new password: Re-enter to confirm the new password.

NOTE:

The default password d isplay s a s n ull, user s can log on t he web-b ased utility w ithout a ny authent icati on.
To secure the router and your network, it is highly recommended that you change the initial password.

10.8 Syslog

The section is to view the system l og. You can view vari ous conditions appearing after system start, and
also check whether there’s an attack on the network. The log can record at most 150 entries.

 Refresh: Click this button to update the log.
 Clear: Click this button to clear the curre nt sh own log.

10.9 Log out

After all settings are finished, please click’” Log out” to exit securely and completely.

44

11N Wireless Broadband Router User Guide

Appendix 1 Glossary

Channel:

An instance of medium use for the purpose of passing protocol data units (PDUs) that may be used
simultaneously, in the same volume of space, with oth er instances of medium use(on other channels) by
other instances of the same physical layer (PHY),with an acceptably low frame error ratio(FER) due to
mutual interference.
SSID:
SSID (Service Set Identifier) is the network name shared by all devices in a wireless network. Your
network’s SSID should be unique to your network and identical for all devices within the network. It is
case-sensitive and must not exceed 20 characters (use any of the characters on the keyboard).Make
sure this setting is the same for all devices in your wireless network.

WPA/WPA2 Encryption:

A security prot ocol for w irele ss network s that buil ds on the basic f oundati ons of WEP. It secures wireless
data transmission by using a key simi lar to WEP, but the adde d strength of WPA is that t he key changes
dynamically. The changing key makes it much more difficult for a hacker to learn the key and gain
access to the network.WPA2 is the second generation of WPA security and provides a stronger
encryption mechanism through Advanced En cryption Standard (AES), which is a requirement for some
government users.

802,1x authentication

Static WEP key is dif fic ult to man age for w hen y ou change the key, you will have to inform all others, an d
if the key is disclosed in one of the places, the key can no longer provide security. Besides, there’s
severe security loop hole about static WEP encryption. The WEP key can be decrypted after one person
receives a specific amount of data via wireless intercepting. 802,1x is initially used for wired Ethernet
authentication access to prevent illegal users from accessing the network. Later, it is found that 802.1x
can better solve the wireless network security problem. EAP-TLS of the 802.1x su ccessfully achieves
the two-way authentication between users and networks, i.e. can prevent illegal users from accessing
the network and can also prevent users from accessing the illegal AP. 802.1x utilizes dynamic WEP
encryption to protect the WEP key from being decrypted. To solve the publishing problem for digital
certification, people make some changes to TLS authentication and TTLS and EAP come into exist,
which enable you to access the network by using the traditional way of authentication: username and
password.

45

11N Wireless Broadband Router User Guide

Appendix 2 Product Features

 Supports IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3 and IEEE 802.3u standards.
 High gain omni-directional antenna, with strong signals and long tran smission distance.
 Wireless transmission rate up to 150 M bps or 300 Mbps
 Provides one 10/100Mbps auto-negotiation Ethernet WAN port to connect to the Wide Area

Network
 Provides four 10/100Mbps auto-negotiation Ethernet LAN ports to connect to the Local Area

Network

 Supports Auto MDI/MDIX
 Supports xDSL/Cable MODEM, static and dynamic IP in community broadband networking
 Includes router, wireless access point, four-port switch and firewall all in one
 SupportsWPA-PSK,WPA2-PSK,andWPA-PSK&W PA2-PSK mixed security modes
 Supports WPS button
 Supports hidden SSID function and MAC address-based access control
 Supports WMM to make your audio and video smoother
 Supports SNTP
 Supports UPnP and DDNS
 Supports WDS to extend wireless network
 Supports wireless WAN and all ows access to ISP’s wireless hotspots to s hare Internet access

with multiple computers (this function applies only to some of the products).

 Supports virtual server, DMZ host
 Provides syslog to record the running status of the router

46

11N Wireless Broadband Router User Guide

Appendix 3 FAQ

This section provides so me solutions to the problems which may occur during the router’s installation or
usage. The instructions below may help you deal with the problems. If your problem is not in the list,
please log into our website http://www.allnet.de or send an E-mail to [e-mail] , and we will
reply to you at the earliest time.

1. Can not log in to the Web-based Utility of the router after you enter the IP address in the address
field?

Step 1: Check if the router is working correctly, after the device is powered on for a few seconds, th e SYS
indicator on the front panel should light up. If it is not, please contact us.
Step 2: Check the network cables are connected correctly and the corresponding LED indicator lights
up. Sometimes, the indicator lights up, but it does not mean it is functioning.
Step 3: Run “Ping” command and check if it can ping the Router’s LAN IP address 192.168.0.1 (open
“Command Prompt” and type “Ping 192.168.0.1” and then enter). If it is OK, please make sure your
browser does not access the In ternet by proxy server. If the ping fails, you can press the “RESET”
button for 7 seconds to restore to default settings. And then repeat the ping operation. If it still does not
work, please contact us.

2. Forgot the login password and cannot enter the Web-based Utility. What can I
do?
Press the “RESET” button for 7 seconds to restore the Router to default settings.

3. The computer connected with the Router shows IP address conflict. What can
do?

Check if there are other DHCP servers in the LAN and if there are then disable them. The default IP
address of the router is 192.168.0.1 please maker sure the address is not being used by any other
device. If there are two computers with the same IP address, please change one of them.

4. I cannot use E-mail and access the Internet. What can I do?

Sometimes happens with ADSL connection and Dynamic IP users. You may need to modify the default
MTU value (1492). Please open the “WAN Setting” and modify the MTU value with the recommended
value as 1450 or 1400.

5.How to share my computer’s resource with other users in Internet？

If you want Internet users to access the internal server via the router such as: e-mail server, Web, FTP.
You can configure the “Virtual Server”.
Step 1: create your internal server, make sure the LAN users can access these servers and know

47

11N Wireless Broadband Router User Guide

related service port. For example, Web server’s port is 80; FTP is 21; SMTP is 25 and POP3 is 110.

Step 2: In the router’s web click “Virtual Server ” and select “Port Range Forwarding”.
Step 3: Input the service port provided by the router (i.e. the external port) for mapping the internal and

external network, for example, 80-80.

Step 4: input the internal Web service port, for example, 80-80.
Step 5: Input the internal server’s IP address. For example, if your Web server’s IP address is

192.168.0.10, please input it.

Step 6: select the communication protocol used by your internal host: TCP, UDP, Both.
Step 7: click “Ok” to activate the setting s.

The following table lists some well-known applications and their respective service ports:

Server Protocol Service Port
WEB Server TCP 80
FTP Server TCP 21
Telnet TCP 23
NetMeeting TCP 1503、1720

MSN
Messenger

PPTP VPN TCP 1723
Iphone5.0 TCP 22555
SMTP TCP 25
POP3 TCP 110

TCP/UDP

File Send:6891-6900(TCP)
Voice:1863、6901(TCP)
Voice:1863、5190(UDP)

48

11N Wireless Broadband Router User Guide

Appendix 4 Clear Wireless Configuration

Clear Wireless configuration file under wi ndows XP

1. Right click “My Network Places” on your computer desktop and select “Properties”.

2. Right click “Wireless Network Connections” and select “Properties”.

3. Click “Wireless Network Configuration” and clear the corresponding wireless configuration file as
shown below.

49

11N Wireless Broadband Router User Guide

Clear Wireless configuration file under windows 7

1. Right click “Network” and click “Properties”.

2. Click “Manage wireless networks” on the left side of the window.

3. Delete the corresponding configured file in the “Manage wireless networks”.

50

11N Wireless Broadband Router User Guide

Appendix 5 Regulatory Information

EU Declaration or Declaration of Conformity

Hereby, ALLNET GMBH, Maistr. 2 82110 Germering, declares that this Wireless Broadband Router is in
compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules . The se limits are designed to provide reasonable protection agai nst
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this eq uipment does cause harmful interference
to radio or television recepti on, w hich c an be d etermin ed by turning t he e quipment off and on, th e user is
encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance co uld v oid the u ser’s authority to op erate this equipment . (Ex ample- us e only
shielded interface cables when connecting to computer or peripheral devices).
“The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.”

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with the minimum distance of 20 cm. Operation is
subject to the following two conditions:

1) This device may not cause interference, and

2) This device must accept any interference, including interference that may cause undesired operation
of the device.

Caution!

The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate the
equipment.

51

11N Wireless Broadband Router User Guide

The safety advice in the document accompanying the p
products shall be obeyed. The conformity to the above
directive is indicated by the CE sign on the device.

The ALLNET ALL02800N conforms to the Council Directives of EC EMC
2004/108/EC with CE marking requirement. This equipment meets the the
following conformance standards:

This equipment is intended to be operated in all countries.

This declaration is made by

ALLNET Deutschland GmbH
Maistr. 2
82110 Germering

Germering, 10.07.2012

52