Assembly Instruction
)
,)p
to dust or wipe carefully
CAUTION: Read instruction carefully and turn electricity off at main circuit breaker panel
before beginning installation.
Care and Cleaning
To clean the outside of the fixture, use a dry or slightly dampened clean cloth(use clean
water, never a solvent
to wipe the surface of the fixture.
To clear the inside of the fixture, first disconnect power to the fixture by turning off the circuit
breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean
cloth(use clean water, never a solvent) to wipe the interior surface of the fixture
Do not use any cleaners with chemical, solvents or harsh abrasives. Use Only a dry soft cloth
.
Estimated Assembly Time:30 minutes
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY
Tubt w/ shade
Tubt w/ shade
Allen Wrench
1X
1X
1X
C
A
B
Mounting Plate
Lamp Body
Canopy Nut
1X
1X
2X
G
H
I
D
E
F
Hex Nut
Spring Washer
Tubt w/ shade
3X
3X
1X
1 / 3
1 / 3
J
K
L
Wire Nut
Mounting Screw
Bulb
3X
2X
3X
Installation
p
Separate the Mounting Plate(A) from the Lamp
A
K
pp y
pp y
ill b
illustrati
ft)
Step 1
Unpack all parts from cartons carefully.
Separate the Mounting Plate(A) from the Lam
Body(B) by removing the Canopy Nut(C) anticlockwise.
Step 2
Insert each Tube w/shade(F,G,H) through the
hole of the canopy of the Lamp Body(B). Place
Spring Washer(E) onto each threaded nipple
of the tube, fix each tube in place by turning
the Hex Nut(D) with Allen Wrench(I) clockwise
till tight as diagram.
Step 3
Insert the J-box wires through the center
opening of Mounting Plate (A).
ttach the Mounting Plate (A) onto the J-box and
secure it by turning the 2 Mounting Screws (K)
clockwise until tight.
A
Step 4 Wire connection
Connect,Hot,Black or Red outlet Supply Wire to: Connect,Neutral,White Outlet Supply Wire to:
Black White
*Parallel Cord(round&smooth) *Parallel Cord(square&ridged)
Clear,Brown,Gold or Black without Tracer(colored stripes) Clear,Brwn,Gold or Black without Tracer(colored stripes)
Insulated Wire(not green)with copper metal conductor Insulated Wire(not green)with Silver metal conductor
*Note: When parallel wire(SPTI&SPTII)is used. The neutral wire is square shaped and
ridged and the hot wire w
e round in shape and smooth.(See
2 / 3
2 / 3
on on le
Grounding Instructions:
Positi
(B)
THERE ARE 39W LED BULBS IN THE BOX.
a) For installation in the United States: Wrap ground wire from outlet box around green
ground screw on mounting bracket, no less than 2" from wire end. Tighten ground screw. If
fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector.
b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire
around green grounding screw on mounting bracket. Tighten ground screw.
Step 5
on the canopy of the Lamp Body
over
the Mounting Plate(A),fix the Lamp Body(B) by
rotating the Canopy Nut(C)clockwise until
secure. Do not over tighten.
Insert the bulb(L) into the socket until secure.
DO NOT EXCEED THE SPECIFIED
WATTAGE.
PLEASUE USE TYPE"A" BULB MAX 60-WATT
OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT
THERE ARE 3*9W LED BULBS IN THE BOX.
Step 6
Consult a qualified electrician to ensure correct branch
circuit conductor
ENJOY YOUR LAMP
3 / 3
3 / 3
Loading...