Assembly Instructions
Caution: You must read this before you proceed.
Please look in the Table Top for hardware packs and legs.
Corner Chair
Caution: This Chair is NOT a TOY.
Keep your child/children at bay during the assembly process.
Whenever moving/lifting the Chair and to prevent damage to the Chair, two
adults are needed to execute these actions.
1 of 10
No. Qty
C 1
D 1
E 1
F 1
G 1
H 1
O 1
J 1
K 1
L 1
M 1
N 1
Part List
Picture
Description
Left Backrest Panel
Right Backrest Panel
Left Panel
(with Pre-installed
Levellers)
Right Panel
(with Pre-installed
Levellers)
Left Corner Leg
Right Corner Leg
Seat Panel
Left Back Support Bar
Right Back Support Bar
Seat Cushion
Left Back Cushion
Right Back Cushion
2 of 10
No. Qty
④ 10
⑤ 3
⑥ 4
⑦ 11
⑧ 2
Hardware
Picture
Description
Bolt
(M6x35mm)
Bolt
(M6x40mm)
Sleeve Nut
(M6x15mm)
Screw
(M6x55mm)
Allen Key
Assembly Preparation
Before Beginning Assembly:
3 of 10
Step 1
Assembly Steps
Overview
This Left Chair has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the Left Chair parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.
Unpack and place all parts on a clean, non-marring surface.
FRONT FACING
Left Backrest
Panel (C)
Left Panel (E)
Seat Panel (O)
Seat Cushion (L)
Right Corner Leg (H)
Left Back
Cushion (M)
Right Backrest Panel (D)
Right Panel (F)
Left Corner Leg (G)
Left Back
Support Bar (J)
Right Back
Support Bar (K)
Right Back Cushion (N)
4 of 10
Step 2
With the help of your adult partner, position the Left Leg(G) as pictured.
Insert dowels on Left Back Support Bar(J) and Left Backrest Panel(C) into mountings on
the Left Corner Leg(G).
Attach Back Support Bar(H) and Left Backrest Panel(C) to Left Corner Leg(G) using
Screws(⑦) with Allen Key(⑧).
Do not fully tighten the Screws.
Step 3
Insert dowels on Right Back Support Bar(K) and Right Backrest Panel(D) into mountings
on Right Corner Leg(H) as shown above.
Attach Right Back Support Bar(K) and Right Backrest Panel(D) to Right Corner Leg(H)
using Screws(⑦) with Allen Key(⑧).
Do not fully tighten the Screws.
5 of 10
Step 4
Insert dowels on Left Back Support Bar(J) and Left Backrest Panel(C) into mountings on
Left Panel(E).
Attach Left Back Support Bar(J) and Left Backrest Panel(C) to Left Panel(E) using
Bolts(④) with Allen Key(⑧).
Do not fully tighten the Bolts.
Step 5
Insert dowels on Right Back Support Bar(K) and Right Backrest Panel(D) into mountings
on Right Panel(F).
Attach Right Back Support Bar(K) and Right Backrest Panel(D) to Right Panel(F) using
Bolts(④) with Allen Key(⑧).
Do not fully tighten the Bolts.
6 of 10
Step 7
Step 6
Align the Left Panel(E) to Right Panel(H) and attach using Bolts(⑤) with Allen Key(⑧).
Do not fully tighten the Bolts.
Align Left Corner Leg(G) to Right Corner Leg(H) as shown above.
Attach Left Corner Leg(G) to Right Corner Leg(H) using Bolts(④) and Sleeve Nuts(⑥)
with Allen Keys(⑧).
Do not fully tighten the Bolts.
7 of 10
Step 8
Insert the Seat Panel(O) into the Chair frame as shown in picture above.
Attach Seat Panel(O) to Chair frame using Screws(⑦) with Allen Key(⑧).
Note: Insert Screws(⑦) from inside to outside of Seat Panel(O).
Do not fully tighten the Screws.
Step 9
Inspect the Chair and make sure all parts are adequately connected.
Carefully sit onto the Chair. This pressure will help align all parts at all joints.
In a sequential manner, tighten all Bolts and Screws at all joints.
Adjust the Levellers until the Chair is level with the ground.
To adjust the Levellers, get assistance from an adult partner to lift/lean and hold
the Chair while you are working.
Adjust Pre-installed Levellers
height for balance
8 of 10
Place Seat Cushion(L), Left Back Cushion(M) and Right Back Cushion(N) onto the
Chair, and affix the velcro straps around the Chair as shown above.
Your Corner Chair is ready for use.
This Corner Chair can only be used on a flat, level surface.
Step 11
With assistance from your adult partners, place the Chairs facedown and connect the
pre-attached clips to connect the Chairs together.
Note: This is an optional step in case you want to connect all the Chairs in the set
together and should be performed before affixing the cushions.
Step 10
9 of 10
10 of 10
Loading...