SWING CHAIR
Thank you for purchasing the SWING CHAIR！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
Hardware:
Component:
B
C
D
E
F
G
H
J
K
Bolt/Nut M10x55mm x1
Bolt/Nut M10x60mm x4
Bolt/Nut M10x20mm x3
Leveler x10
Screw Set M6x30mm x2
Spring x1
Spring Holder x1
Allen Wrench x1
Open Wrench x1
4
1
Left Base x1
Upper Stand x1
4
5
6
3
2
1
Right Base x1
2
Basket Frame x1
5
3
Lower Stand x1
6
Cushion x1
Page 1 of 3
SWING CHAIR
STEP 1:
Please put all chair parts on a carpeted or padded area.
Find hardware package in the box packing Base (1/2) & Stand (3/4).
Place left Base (1) to Right Base (2) as shown.
Secure the back of base by using 3 sets of Bolts/Nuts (D).
Secure the front of base by using 2 sets of Screw Set (F).
Use Allen Wrench (J) and Open Wrench (K) to tighten Bolts/Nuts (D) clockwise until secure.
Use Phillips Head Screw Driver (Not Provided) to tighten Screw Sets (F).
Secure 10 pieces of Leveler (E) into the bottom of assembled Base as shown.
STEP 2:
Attach Lower Stand (3) to the assembled Base as shown.
Secure the back of base by using 4 sets of Bolts/Nuts (C).
Use Allen Wrench (J) and Open Wrench (K) to tighten Bolts/Nuts (C) clockwise until secure.
STEP 3:
Insert Upper Stand (3) into Lower Stand (4) as shown.
Secure by using 1 set of Bolt/Nut (B) .
Use Allen Wrench (J) and Open Wrench (K) to tighten Bolt/Nut (B) clockwise until secure.
STEP 4:
Place Cushion (7) to the assembled Basket Frame (5).
STEP 5:
Insert Spring Holder (H) into the pre-drilled hole at the top of Upper Stand (4) as shown.
Hang the assembled Basket Frame (5/6) to Upper Stand (4) by using 1 piece of Spring (G) as shown.
Bx1 Cx4 Dx3 Ex10 Fx1 Gx1 Hx1 Jx1 Kx1
Hardware & Tool required
Page 2 of 3
SWING CHAIR
H
STEP 5
G
4
STEP 4
STEP 4
6
B
B
STEP 3
5
3
C
C
C
E
1
D
C
STEP 2
Maximum Weight: 120 KG
Assembly is completed. The swing chair is ready to enjoy now!
D
E
F
F
E
E
E
STEP 1
E
E
E
2
F F
E
C
C
C
E
C
Page 3 of 3
Loading...