L OVE S E AT - L E FT
C aution: You mus t read this before you proc eed
C AUT ION : This Loveseat is NOT a TOY.
Keep your child / children at bay in the process of assembly.
For turning the Chair and to prevent damage to the Chair 02 persons may be
needed to execute this action.
Page 1 of 8
Page 1 of 8
L abel P ic ture Des c ription QT Y
①
②
③
④
⑤
A
B
C
D
E
Seat Panel 1
Backrest Panel 1
First legs 2
Second legs 2
Seat Cushion 1
F
Back Cushion 1
L abel P ic ture Des c ription QT Y
Long Bolts
(
M8 x 60mm)
Flat Washers
(M8xD2mmm)
Short Bolts
(M6x40mm)
Sleeve Nut M6x15 7
9
9
7
Allen Key 2
Page 2 of 8
Page 2 of 8
Before Beginning Assembly:
Overview
This Chair has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Chair parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps before
assembly.
Backrest Panel
(B)
Seat Panel
(A)
Leg
(D)
Leg
(C)
Back Cushion
(F)
Seat Cushion
(E)
Leg
(D)
FRONT FACING
Page 3 of 8
Page 3 of 8
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
2.1
2.2
2.3
2.1) With assistance from your adult partners, turn the Seat panel (A) up side down as shown in
picture above.
2.2) Attach the First Leg (C) to the Seat panel (A) by using Long bolts (①), Flat washer (②) and
Allen Key (⑤) as shown in picture above.
2.3) Repeat the same process to attach the remaining First Leg (C) into the diagonal position in
Seat Panel (A).
Do not fully tighten the Bolts
Page 4 of 8
Page 4 of 8
Step 3
Step 4
Attach the Second Leg (D) to the Seat panel (A) by using Long bolts (①), Flat washer (②) and
Allen Key (⑤) as shown in picture above.
Repeat the same process to attach the remaining Second Leg (D) into the diagonal position in
Seat Panel (A).
Do not fully tighten the Bolts.
4.2
4.1
4.3
4.1) With assistance from your adult partners, turn the Seat panel (A) right side up.
4.2) Attach the Backrest (B) to Seat panel (A) as shown in picture above.
4.3) Affix the Backrest (B) to Seat panel (A) by using Short Bolts (③), Slevee nut (④) and Allen
Key (⑤) as shown in picture above.
Do not fully tighten the Bolts.
Page 5 of 8
Page 5 of 8
Step 5
secured.
Inspect the Chair and make sure all parts are adequately connected.
EXERT pressure, floorwards, onto the Seat.
This pressure will help the Legs and Seat panel reach alignment at all
joints.
Check for wobbles.
In a sequential manner, gradually tighten all Bolts, Screws until evenly
Step 6
Place Seat Cushion (E), Back Cushion (F) on the chair as shown in
picture above.
Secure the velcro straps as shown in diagrams.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
Page 6 of 8
Page 6 of 8
Step 7
placing cushion
placing cushion
Note: This is optional step in case we want to connect all Corner
chair and Loveseats in a set together and should be done before
With assistance from your adult partners, up side down the chairs and
using pre-fixed clip to connect the chairs together
Page 7 of 8
Page 7 of 8
Page 8 of 8Page 8 of 8
Loading...