Page 1
x900 Series Switch and SwitchBlade® x908
Expansion Module
Installation Guide
XEM-1XP
XEM-2XP
XEM-2XS
XEM-12S
XEM-12Sv2
XEM-12T
XEM-12Tv2
XEM-2XT
XEM-24T
XEM-STK
Page 2
Expansion Modules
x900 Series Switch and SwitchBlade® x908 Expansion Module Installation Guide
Document Number 613-000032 REV N
© 2005-2012 Allied Telesis, Inc. All rights reserved. No part of this publication
may be reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis, Inc. reserves the right to change specifications and other
information in this document without prior written notice. The information
provided herein is subject to change without notice. In no event shall Allied
Telesis, Inc. be liable for any incidental, special, indirect, or consequential
damages whatsoever, including but not limited to lost profits, arising out of or
related to this manual or the information contained herein, even if Allied Telesis,
Inc. has been advised of, known, or should have known, the possibility of such
damages.
Allied Telesis, AlliedWare, AlliedWare Plus, and SwitchBlade are trademarks or
registered trademarks in the United States and elsewhere of Allied Telesis, Inc.
Adobe, Acrobat, and Reader are either registered trademarks or trademarks of
Adobe Systems Incorporated in the United States and/or other countries.
Microsoft and Visio are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries. Additional brands,
names and products mentioned herein may be trademarks of their respective
companies.
2
Page 3
Installation Guide
Contents
About this Guide .............................................................................................................. 4
Compatible Switches and Operating Systems ........................................................... 5
Compatible Pluggable Optical Modules ....................................................................... 6
Package Contents ............................................................................................................. 6
XEM-1XP 10 Gigabit XFP Port ...................................................................................... 7
XEM-2XP Dual 10 Gigabit XFP Ports .......................................................................... 9
XEM-2XS Dual 10 Gigabit SFP+ Ports ....................................................................... 11
XEM-12S 100/1000 BASE-X SFP Ports ...................................................................... 13
XEM-12Sv2 100/1000 BASE-X SFP Ports .................................................................. 15
XEM-12T 10/100/1000 BASE-T RJ-45 Ports ............................................................. 17
XEM-12Tv2 10/100/1000 BASE-T RJ-45 Ports ........................................................ 19
XEM-2XT Dual 10G BASE-T RJ-45 Ports ................................................................. 21
XEM-24T 24 Tri-speed Gigabit Copper Ports ......................................................... 22
XEM-STK Stacking Ports .............................................................................................. 24
Installation Procedure .................................................................................................... 26
Obtaining Documentation and Resources ............................................................... 30
3
Page 4
Expansion Modules
About this Guide
Optional expansion modules (XEMs) enable economical combinations of port
type, speed and density in a single switch. Front bays in the switch allow quick
and easy installation.
This Installation Guide describes how to install the following XEMs:
■ XEM-1XP, a single XFP port for high-speed fibre connections
■ XEM-2XP, a dual 10 GbE XFP port expansion module for high-speed fibre
connections
■ XEM-2XS, a dual 10 GbE SFP+ port expansion module for high-speed fibre
and SFP+ Direct Attach copper connections
■ XEM-12S, 12 SFP ports for copper and fibre links
■ XEM-12Sv2, 12 SFP ports for copper and fibre links
■ XEM-12T, 12 x 10/100/1000 Mbps RJ-45 ports
■ XEM-12Tv2, 12 x 10/100/1000 Mbps RJ-45 ports
■ XEM-2XT, a dual 10 GbE RJ-45 port expansion module for high-speed
copper connections
■ XEM-24T, 24 x RJ Point Five ports for high density cabling solutions
■ XEM-STK, dual stacking ports for scalability and high availability
You can download the complete document set for x900 Series switches and
SwitchBlade® x908 from www.alliedtelesis.com/support/software. For more
information about the document set and other resources, see “Obtaining
Documentation and Resources” on page 30.
4
Page 5
Installation Guide
Compatible Switches and Operating Systems
XEMs can be installed in the following switches:
■ x900-12XT/S
■ x900-24XT
■ x900-24XT-N
■ x900-24XS
■ SwitchBlade x908
The SwitchBlade x908 can operate in Extended Mode to take advantage of
larger table sizes and Link Aggregation Groups, as shown in the following table:
Standard Mode Extended Mode
MAC entries 16K 32K
LAGs 31 128
Extended Mode can be enabled when the following XEMs are installed in a
SwitchBlade
■ XEM-2XP
■ XEM-2XS
■ XEM-12Sv2
■ XEM-12Tv2
■ XEM-2XT
■ XEM-24T
x908 switch:
The AlliedWare Plus™ Operating System supports all XEMs. The AlliedWare®
Operating System supports all XEMs except the XEM-STK, the XEM-2XP and
the XEM-2XT.
5
Page 6
Expansion Modules
Compatible Pluggable Optical Modules
For the latest list of approved SFP, SFP+ and XFP fibre transceivers plus SFP+
Direct Attach copper modules, contact your authorised Allied Telesis
distributor or reseller. See the most current revision available of the XEM
datasheet (document number 617-000034) for further information about which
SFP, SFP+, and XFP fibre transceivers and SFP+ Direct Attach copper modules
are approved for use.
Package Contents
The following items are included with each XEM:
■ this Installation Guide
■ one warranty card
Contact your authorised Allied Telesis distributor or reseller if any items are
damaged or missing.
6
Page 7
Installation Guide
XFP
XFP
L/A
L/A
LINK ACT ENABLED DISABLED
FAULT
XEM-1XP
XEM-1XP 10 Gigabit XFP Port
The XEM-1 XP single-port 10 Gigabit Ethernet expansion module features:
■ one XFP port
■ LEDs showing port status
■ support for hot-swappable XFP transceiver modules
Front view XEM-1 XP
The following LEDs report operations and faults on the XEM-1 XP.
LED State Description
L/A
(Link Activity)
Green An XFP transceiver module is installed and a 10 Gb
link has been established.
Green
flashing
An XFP transceiver module is installed and link
activity is occurring.
Off A link has not been established.
XFP Green An XFP transceiver module is installed and enabled.
Amber An XFP transceiver module is installed but not
operating or is disabled.
Amber
The installed XFP transceiver module has a fault.
flashing
Off An XFP transceiver module is not installed.
7
Page 8
Expansion Modules
For the latest list of approved XFP transceiver modules, contact your authorised
Allied Telesis distributor or reseller. See the most current revision available of
the XEM datasheet (document number 617-000034) for further information
about which XFP transceiver modules are approved for use with the XEM-1XP.
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
8
Page 9
Installation Guide
XFPL/A
LINK ACT ENABLED DISABLED
FAULT
XEM-2XP
XFP
L/A
XFP
L/A
1
2
XEM-2XP Dual 10 Gigabit XFP Ports
The XEM-2 XP Dual 10 Gigabit Ethernet expansion module features:
■ two XFP ports
■ four LEDs (one set for each XFP port) showing port status
■ support for hot-swappable XFP transceiver modules
Front view XEM-2 XP
The following LEDs report operations and faults on the XEM-2XP.
LED State Description
L/A
(Link Activity)
Green An XFP transceiver module is installed and a 10
Gbps link has been established.
Green
flashing
An XFP transceiver module is installed and link
activity is occurring.
Off A link has not been established.
XFP Green An XFP transceiver module is installed and enabled.
Amber An XFP transceiver module is installed but not
operating or is disabled.
Amber
flashing
The installed XFP transceiver module is not ready
or has a fault.
Off An XFP transceiver module is not installed.
9
Page 10
Expansion Modules
For the latest list of approved XFP transceiver modules, contact your authorised
Allied Telesis distributor or reseller. See the most current revision available of
the XEM datasheet (document number 617-000034) for further information
about which XFP transceiver modules are approved for use with the XEM-2XP.
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
10
Page 11
Installation Guide
L/A
L/A
LINK ACT
ENABLED DISABLED FAULT
L/A
XEM-2XS
1
2
SFP+
SFP+
SFP+
XEM-2XS Dual 10 Gigabit SFP+ Ports
The XEM-2 XS Dual 10 Gigabit Ethernet expansion module features:
■ two SFP+ ports
■ four LEDs (one set for each SFP+ port) showing port status
■ support for hot-swappable SFP+ fibre transceivers and Direct Attach copper
modules
Front view XEM-2 XS
The following LEDs report operations and faults on the XEM-2XS.
LED State Description
L/A
(Link Activity)
Green An SFP+ fibre transceiver or a Direct Attach copper
module is installed and a 10 Gbps link has been
established.
Green
flashing
An SFP+ fibre transceiver or a Direct Attach copper
module is installed and link activity is occurring.
Off A link has not been established.
11
Page 12
Expansion Modules
LED State Description
SFP+ Green An SFP+ fibre transceiver or a Direct Attach copper
module is installed and enabled.
Amber The port is disabled because either a non SFP+ fibre
transceiver or a disabled Direct Attach copper module
is installed.
Amber
flashing
Off An SFP+ fibre transceiver or a Direct Attach copper
For the latest list of approved SFP+ fibre transceivers and Direct Attach copper
modules, contact your authorised Allied Telesis distributor or reseller. See the
most current revision available of the XEM datasheet (document number 617-
000034) for further information about which SFP+ fibre transceivers modules
and Direct Attach copper modules are approved for use with the XEM-2XS.
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
The SFP+ fibre transceiver is not ready or has a fault.
Direct Attach copper modules cannot indicate a fault.
module is not installed.
12
Page 13
Installation Guide
XEM-12S 100/1000 BASE-X SFP Ports
The XEM-12 S 12-port 100/1000BASE-X expansion module features:
■ two rows of 6 SFP ports
■ LEDs showing port status
■ support for hot-swappable SFP transceiver modules
■ NEBS compliant
Front view XEM-12 S
The following LEDs report operations and faults on the XEM-12 S.
XEM-12S
LED State Description
SFP Green An SFP transceiver module is installed and a link has
been established.
Green
flashing
An SFP transceiver module is installed and link
activity is occurring.
Amber An SFP transceiver module is installed but a link has
not been established.
Amber
flashing
An SFP transceiver module is installed but there is a
fault.
Off An SFP transceiver module is not installed.
13
Page 14
Expansion Modules
For the latest list of approved SFP transceiver modules, contact your authorised
Allied Telesis distributor or reseller. See the most current revision available of
the XEM datasheet (document number 617-000034) for further information
about which SFP transceiver modules are approved for use with the XEM-12S.
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
14
Page 15
Installation Guide
XEM-12Sv2 100/1000 BASE-X SFP Ports
The XEM-12 S 12-port 100/1000BASE-X expansion module features:
■ two rows of 6 SFP ports
■ LEDs showing port status
■ support for hot-swappable SFP transceiver modules
Front view XEM-12 Sv2
The following LEDs report operations and faults on the XEM-12 Sv2.
XEM-12Sv2
LED State Description
SFP Green An SFP transceiver module is installed and a link has
been established.
Green
flashing
An SFP transceiver module is installed and link
activity is occurring.
Amber An SFP transceiver module is installed but a link has
not been established.
Amber
flashing
An SFP transceiver module is installed but there is a
fault.
Off An SFP transceiver module is not installed.
15
Page 16
Expansion Modules
For the latest list of approved SFP transceiver modules, contact your authorised
Allied Telesis distributor or reseller. See the most current revision available of
the XEM datasheet (document number 617-000034) for further information
about which SFP transceiver modules are approved for use with the XEM-12Sv2.
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
16
Page 17
Installation Guide
XEM-12T
XEM-12T 10/100/1000 BASE-T RJ-45 Ports
The XEM-12 T 12-port RJ-45 expansion module features:
■ two rows of 6 RJ-45 ports
■ gigabit ports that support speeds of 10/100/1000 Mbps
■ LEDs showing port status
■ cable fault detection and distance-to-fault diagnostics on switches running
the AlliedWare® operating system (see the Test Facility chapter in the
Software Reference for the switch)
Front view XEM-12 T
The following LEDs report operations and faults on the XEM-12 T.
LED State Description
L/A
(Link Activity)
Green A 1000 Mbps link has been established.
Green
1000 Mbps activity is occurring.
flashing
Amber A 10/100 Mbps link has been established.
Amber
10/100 Mbps activity is occurring.
flashing
Off A link has not been established.
D/C
(Duplex/
Collision)
Green The port is operating in full duplex mode.
Amber The port is operating in half duplex mode.
Amber
Collisions are occurring.
flashing
17
Page 18
Expansion Modules
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
18
Page 19
Installation Guide
XEM-12Tv2 10/100/1000 BASE-T RJ-45 Ports
The XEM-12 Tv2 12-port RJ-45 expansion module features:
■ two rows of 6 RJ-45 ports
■ gigabit ports that support speeds of 10/100/1000 Mbps
■ support for Energy Efficient Ethernet
■ LEDs showing port status
■ cable fault detection and distance-to-fault diagnostics on switches running
the AlliedWare® operating system (see the Test Facility chapter in the
Software Reference for the switch)
Front view XEM-12 Tv2
XEM-12Tv2
The following LEDs report operations and faults on the XEM-12 Tv2.
LED State Description
L/A
(Link Activity)
Green A 1000 Mbps link has been established.
Green
1000 Mbps activity is occurring.
flashing
Amber A 10/100 Mbps link has been established.
Amber
10/100 Mbps activity is occurring.
flashing
Off A link has not been established.
19
Page 20
Expansion Modules
LED State Description
D/C
(Duplex/
Collision)
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
Green The port is operating in full duplex mode.
Amber The port is operating in half duplex mode.
Amber
flashing
Off A link has not been established.
Collisions are occurring.
20
Page 21
Installation Guide
XEM-2XT
L/A
L/A
10G LINK ACT
L/A
1
2
XEM-2XT Dual 10G BASE-T RJ-45 Ports
The XEM-2 XT Dual 10 GBASE-T RJ-45 expansion module features:
■ two 10GBASE-T RJ-45 ports
■ LEDs showing port status
Front view XEM-2 XT
The following LEDs report operations and faults on the XEM-2XT.
LED State Description
L/A
(Link Activity)
Green A 10 Gbps link has been established.
Green
10 Gbps activity is occurring.
flashing
Off A link has not been established.
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
Note You must use Cat 6A cables to enable the XEM-2XT to achieve optimal
performance. In noisy RF environments, we recommend shielded Cat 6A cables.
21
Page 22
Expansion Modules
XEM-24T 24 Tri-speed Gigabit Copper Ports
The XEM-24 T 24-port RJ Point Five expansion module features:
■ two rows of 12 RJ Point Five ports
■ gigabit ports that support speeds of 10/100/1000 Mbps
■ support for Energy Efficient Ethernet
■ LEDs showing port status
■ cable fault detection and distance-to-fault diagnostics on switches running
the AlliedWare® operating system (see the Test Facility chapter in the
Software Reference for the switch)
Front view XEM-24 T
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
XEM-24T
The following LEDs report operations and faults on the XEM-24 T.
LED State Description
L/A
(Link Activity)
Green A 1000 Mbps link has been established.
Green
1000 Mbps activity is occurring.
flashing
Amber A 10/100 Mbps link has been established.
Amber
10/100 Mbps activity is occurring.
flashing
Off A link has not been established.
22
Page 23
LED State Description
Installation Guide
D/C
(Duplex/
Collision)
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
Green The port is operating in full duplex mode.
Amber The port is operating in half duplex mode.
Amber
flashing
Off A link has not been established.
Collisions are occurring.
23
Page 24
Expansion Modules
PORT 2PORT 1 STACK
SELECT STATUS
ID
XEM-STK
FAULTNEGOTIATING LINK
PORT
STAT
MEMBER MASTER
XEM-STK Stacking Ports
The XEM-STK dual-port stacking expansion module features:
■ two 15 Gbps full duplex stacking connections
■ LEDs showing port and stack member status
■ seven-segment stack ID display
■ recessed Select button to reset stack ID to 1
Front view XEM-STK
The following LEDs report operations and faults on the XEM-STK.
LED State Description
Port 1
Port 2
Green A link has been established.
Amber slow
flashing
Status Green The switch is the stack master.
Amber The switch is a stack member.
Green
flashing
Off The switch is not a stack member.
ID 1 to 8 Numeric ID of the stack member.
Off The switch is not a stack member.
24
The link has a transmission fault.
The switch is in the process of learning the stack
topology and selecting the stack master.
Page 25
Installation Guide
A choice of 0.5 m or 2.0 m stacking cables can be ordered separately. For the
latest list of approved cables, contact your authorised Allied Telesis distributor
or reseller.
The Select button resets the stack ID of this switch to 1, and causes the other
members of the stack to be renumbered. Use this to put the stack into a predefined configuration for ease of installation.
Note You should install only one XEM-STK expansion module in a switch. If
you install more than one, only the first expansion module is enabled.
Caution Allied Telesis recommends waiting 30 seconds after hot swapping
any XEM before resuming normal operations. The switch must fully complete
the bootup process before you can hot swap any XEM. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
25
Page 26
Expansion Modules
Installation Procedure
The installation procedure and XEMs supported by each switch depend on the
operating system running on the switch.
AlliedWare Plus™ Operating System
Switches running the AlliedWare Plus™ operating system support all XEMs. All
XEMs except the XEM-STK are hot-swappable and can be installed following
either of these procedures:
■ “Installing or replacing XEMs without hot swap support” on page 27
■ “Installing or replacing XEMs with hot swap support” on page 28
The XEM-STK is hot-removable only. To remove the XEM-STK, disconnect the
stacking cables, loosen the thumbscrews on the faceplate and remove the XEM.
To install or replace the XEM-STK, follow the procedure “Installing or replacing
XEMs without hot swap support” on page 27.
AlliedWare® Operating System
Switches running the AlliedWare® operating system support all XEMs except
the XEM-STK and the XEM-2XP. XEMs are not hot-swappable under the
AlliedWare® operating system and must be installed following the procedure
“Installing or replacing XEMs without hot swap support” on page 27.
Before you begin
■ Unpack the XEM.
In an anti-static environment, remove the XEM from its packing material. Be
sure to observe ESD precautions.
Caution Failure to observe proper anti-static procedures may damage the
unit. If you are unsure about correct procedures, contact your authorised
Allied Telesis distributor or reseller.
■ Verify the package contents if you have not already done so.
See “Package Contents” on page 6. If any items are damaged or missing,
contact your authorised Allied Telesis distributor or reseller.
■ Read the safety information for the switch.
Safety information is available in the Installation and Safety Guide that is
shipped with each switch. You can also download this document from
www.alliedtelesis.com/support/software.
26
Page 27
Installation Guide
■ Gather necessary tools.
You may need a Phillips #2 screwdriver to adjust the thumbscrews on the XEM.
Installing or replacing XEMs without hot swap support
Follow this procedure to:
■ install a XEM, except the XEM-STK, in a switch running the AlliedWare®
operating system
■ install a XEM-STK in a switch running the AlliedWare Plus™ operating
system
■ install a XEM without hot swapping in a switch running the
AlliedWare Plus™ operating system
To install or replace a XEM:
1. If you are replacing a XEM, first save the switch configuration.
On switches running the AlliedWare® operating system, use the
commands:
create config=<filename>.cfg
set config=<filename>.cfg
On switches running the AlliedWare Plus™ operating system, use the
commands:
awplus>enable
awplus#copy running-config startup-config
2. If connected, disconnect the switch from its redundant power supply.
3. Disconnect the switch from its AC or DC power supply.
4. If you are replacing an existing XEM, disconnect any data cables.
5. Loosen the thumbscrews on the faceplate or existing XEM, and remove it.
Keep the faceplate for future use. If you remove a XEM, cover the bay with
the faceplate to prevent dust and debris from entering it and to maintain
proper airflow.
6. Carefully slide the new XEM into the empty bay until you feel it engage the
rear plug.
7. Secure the XEM by tightening the thumbscrews.
8. Apply power to the switch by re-attaching the power cord.
9. If you disconnected a redundant power supply, reconnect it.
27
Page 28
Expansion Modules
10. Restart the switch and verify the installation.
If you have a terminal connected to the asyn0 port, any error message is
displayed during startup self-tests.
Confirm there is no error message about installation in the log file and that
the switch has recognised the XEM.
On switches running the AlliedWare® operating system, use the
commands:
On switches running the AlliedWare Plus™ operating system, use the
commands:
Installing or replacing XEMs with hot swap support
Caution It is recommended that you should wait 30 seconds between hot
swapping any XEM to resume normal operations. Also ensure the XEM
fastening thumbscrews are fully tightened. If you are unsure about correct
procedures, contact your authorised Allied Telesis distributor or reseller.
Follow this procedure to hot swap a XEM in a switch running the
AlliedWare
swapped.
1. If you are replacing a XEM, first save the switch configuration, by using the
commands:
2. If you are replacing an existing XEM, disconnect any data cables.
3. Loosen the thumbscrews on the faceplate or existing XEM, and remove it.
Keep the faceplate for future use. If you remove a XEM, cover the bay with
the faceplate to prevent dust and debris from entering it and to maintain
proper airflow.
4. Carefully slide the new XEM into the empty bay until you feel it engage the
rear plug.
5. Secure the XEM by tightening the thumbscrews.
show log
show system
awplus>show system
awplus>enable
awplus#show log
Plus™ operating system. Note that the XEM-STK cannot be hot
awplus>enable
awplus#copy running-config startup-config
28
Page 29
Installation Guide
6. Verify the installation.
If you have a terminal connected to the asyn0 port, any error message is
displayed during installation.
Confirm there is no error message about installation in the log file and that
the switch has recognised the XEM, by using the commands:
awplus>show system
awplus>enable
awplus#show log
29
Page 30
Expansion Modules
Obtaining Documentation and Resources
The complete document set for x900 Series switches and SwitchBlade x908
includes:
■ this Installation Guide
■ the x900 Series Switch and SwitchBlade
which describes how to install the switch and includes important safety and
statutory information
■ the x900 Series Switch and SwitchBlade
contains detailed information on the switch and its hardware features
■ the Removable Power Supply and Fan Installation Guide, which describes how to
install power supply units and fan-only modules in the switch
■ the x900 Series Switch
contains detailed information on configuring switches running the
AlliedWare
■ the
detailed information on configuring switches running the AlliedWare Plus™
operating system
You can download these documents and updates from
www.alliedtelesis.com/support/software.
®
x908 Installation and Safety Guide,
®
x908 Hardware Reference, which
AlliedWare® Operating System Software Reference
®
operating system
AlliedWare Plus™ Operating System Software Reference
, which
, which contains
You need Adobe® Acrobat® Reader® software to view, search, or print these
documents. You can download it from www.adobe.com.
Other resources
How-To Notes describe a range of standard Allied Telesis solutions, and include
technical tips and guides to configuring specific hardware and software features.
You can download the latest How-To Notes from
www.alliedtelesis.com/resources/literature/howto.aspx.
MIBs supported by Allied Telesis products can be downloaded from
www.alliedtelesis.com/support/software.
Microsoft® Visio® stencils for Allied Telesis products can be downloaded from
www.alliedtelesis.com/resources/images/visio.aspx.
AT-TFTP Server for Windows is a TFTP (Trivial File Transfer Protocol) server for
transferring software versions, configuration scripts and other files between a
PC and the switch. You download AT-TFTP Server from
www.alliedtelesis.com/support/software.
30
Page 31
Installation Guide
Contacting us
With locations covering all of the established markets in North America, Latin
America, Europe, Asia, and the Pacific, Allied Telesis provides localized sales and
technical support worldwide. To find the representative nearest you, visit us on
the Web at
www.alliedtelesis.com.
31
Loading...