Allied Telesis AT-CV1KSS User Manual

*613-000297 Rev D*

613-000297 Rev. D

DIP Switches

One set of DIP switches allows you to set the operating mode, as described in “DIP Switch
Settings.”

Installing an AT-CV1KSS Line Card

Note

Before you install an AT-CV1KSS line card, refer to the appropriate Converteon
chassis installation guide for electrical safety and emissions information.

LED Descriptions

Status LEDs

The line card has four status LEDs as described in the following table. For more information
about Smart MissingLink and MissingLink, refer to the relevant management software
user’s guide.

LED State Description

RDY Green The line card has passed diagnostics.

AT-CV1KSS Converteon Line Card Installation Guide

Overview

The AT-CV1KSS line card is a dual 1000Base-TX SFP line card. You can install this line
card in any Converteon Series chassis. The line card features two small form factor
pluggable (SFP) transceiver slots. The line card is hot-swappable into and out of a
Converteon chassis.

Related Documents

For details on the features and functions of a Converteon chassis, refer to the relevant
documents on our web site, www.alliedtelesis.com.

Verifying Package Contents

Ensure that the following items are included in your package:

 One AT-CV1KSS line card
 This installation guide

If any item is missing or damaged, contact your Allied Telesis sales representative for
assistance.

AT-CV1KSS Line Card Components

An AT-CV1KSS line card has the components shown below.

4 3 2 1

1 2 3 4

1

SW

DIP Switches

ON

AT-CV1KS

S

LK

A

T

SFP Port LEDs

SFP Ports

Line Card Status LEDs

S
F
P

LK A

T

S
F
P

R

D

Y

SML ML

559

Warning: Remove all metal jewelry, such as rings and watches, before installing
or removing a line card from a powered-on chassis.

Caution: Be sure to observe all standard electrostatic (ESD) precautions, such as
wearing an antistatic wrist strap, to avoid damaging the device. A line card can be
damaged by static electricity

Note

You can install a Converteon line card in any Converteon chassis line card slot.

To install an AT-CV1KSS line card, perform the following procedure:

1. Remove the AT-CV1KSS line card from its shipping package and store the package
in a safe place. You must use the original package if you need to return the unit to
Allied Telesis.

2. Configure the line card’s DIP switches as required. Refer to “DIP Switch Settings” for
more information.

3. Select any line card slot in the chassis where you want to install the AT-CV1KSS line
card, and remove the blank slot cover if one is installed.

4. Align the back edge of the line card with the to and bottom alignment guides located
inside the slot.

5. Slide the line card into the slot until the front of the card is flush with the front of the
chassis.

Note

Avoid touching the line card components.

6. Secure the AT-CV1KSS line card to the chassis by using a Phillips screwdriver to
tighten the captive screw on the faceplate.

Note

Always tighten the captive screw to secure the line card to the chassis.

7. Repeat this procedure to install additional AT-CV1KSS line cards.

Off The line card has not passed diagnostics.

SML Green The Smart MissingLink mode is enabled.

Off The Smart MissingLink mode is disabled.

ML Green The MissingLink mode is enabled.

Off The MissingLink mode is disabled.

SFP Port LEDs

Each SFP port has two LEDs, as described in the following table. For more information
about Smart MissingLink, refer to the relevant management software user’s guide.

LED State Description

LK Green A link has been established on the port.

Blinking
Green

While in Smart MissingLink mode, a valid connection is established
on the port while a link on the other port is lost.

Off No link has been established on the port.

AT Blinking

TX/RX activity has been detected on the port.

Green

Off There is no TX/RX activity on the port.

DIP Switch Settings

The DIP switches described in the following table allow you to set the operating mode of
the line card. For information about the operating modes as well as Smart MissingLink
and MissingLink, refer to the relevant management software user’s guide.

Operating Mode DIP 1 DIP 2 DIP 3 DIP 4

Smart MissingLink (SML) OFF ON ON X

MissingLink (ML) OFF OFF ON X

Link Test (default) OFF OFF OFF X

Manufacturing Defaults OFF OFF OFF X

“X” means that the DIP switch position can be ON or OFF.

Warranty Information

The AT-CV1KSS line card has a limited warranty of five years. Go to
www.alliedtelesis.com/warranty for the specific terms and conditions of the warranty and
for warranty registration.

SFP Ports Description

The SFP ports support an SFP transceiver with a fixed operating speed of 1000 Mbps.

LEDs

The AT-CV1KSS line card has three status LEDs and two LEDs for each SFP port, as
described in “LED Descriptions.”

1 2 3

Specifications

Dimensions (H x W x L) 2.2 cm x 7.3 cm x 13.0 cm

(.78 in. x 2.89 in. x 5.1 in.)

Weight 0.27 kg (0.60 lbs.)

Operating Temperature 0° C to 40° C (32° F to 104° F)

Storage Temperature -25° C to 70° C (-13° F to 158° F)

Operating Relative Humidity 5% to 90% (non-condensing)

Storage Relative Humidity 5% to 95% (non-condensing)

Operating Altitude Range Up to 3,048 m (10,000 ft.)

Predicted MTBF (Telcordia SR332) 1,370,000 hours

Power Consumption 4.75 Watts maximum

Electrical Safety and Emissions Statements

This product meets the following standards when installed in compliant host equipment.

U.S. Federal Communications Commission

Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with this instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void
your right to operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

Emissions FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CE

Warning: In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

Immunity EN55024

Electrical Safety UL60950 (

), EN60950 (TUV), CSA22.2 No. 950

cULus

Copyright © 2007 Allied Telesis, Inc. All rights reserved.

No part of this publication may be reproduced without prior written permission from Allied
Telesis, Inc.

4 5 6