trademark of Netscape Communications Corporation. All other product names, company names, logos or other
designations mentioned herein are trademarks or registered trademarks of their respective owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document
without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied
Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to
lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been
advised of, known, or should have known, the possibility of such damages.
Electrical Safety and Emissions
Standards
This product meets the following standards.
U.S. Federal Communications Commission
Declaration of Conformity
Manufacturer Name: Allied Telesis, Inc.
Declares that the product: Fast Ethernet Fiber (SC) ExpressCard
Model Numbers: AT-2814FX
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
must not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with instructions, may cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal Communications Commission rules.
Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
European Union Restriction of the Use of Certain Hazardous Substances
This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of the Use of Certain Hazardous
Substances (RoHS) in Electrical and Electronic Equipment. Allied Telesis ensures RoHS conformance by requiring
supplier Declarations of Conformity, monitoring incoming materials, and maintaining manufacturing process controls.
(RoHS) in Electrical and Electronic Equipment
RFI EmissionsFCC Class B, EN55022 Class B, VCCI Class B, C-TICK, CE
ImmunityEN55024 Class B
Electrical SafetyEN60950 (TUV), UL 60950-1 (
CULUS
)
Laser SafetyEN60825
3
Translated Safety Statements
Important: The indicates that a translation of the safety statement is available in a PDF
document titled “Translated Safety Statements” posted on the Allied Telesis website at:
www.alliedtelesis.com/support/.
Safety Symbols Used in this Document................................................................................................................................12
LED ...............................................................................................................................................................................17
Supported Operating Systems .............................................................................................................................................18
Contents of Your Shipment ..................................................................................................................................................20
Chapter 2: Installing the Driver Software ........................................................................................................................21
Downloading the Driver Software .........................................................................................................................................23
Installing the Driver Software................................................................................................................................................24
Chapter 3: Installing the Hardware ..................................................................................................................................29
Installing the AT-2814FX ExpressCard ................................................................................................................................33
Connecting the Network Cable.............................................................................................................................................38
Starting the Device Manager ................................................................................................................................................43
Device Manager on Windows XP ..................................................................................................................................43
Device Manager on Windows Vista and Windows 7 ..................................................................................
Flow Control .........................................................................................................................................................................50
Large Send Offload (IPv4)....................................................................................................................................................56
Log Status Messages ...........................................................................................................................................................58
Max IRQ per Sec ..................................................................................................................................................................60
Wake From Shutdown ..........................................................................................................................................................71
Uninstalling the Driver Software ...........................................................................................................................................77
Power Specifications.............................................................................................................................................................79
Cleaning Fiber Optic Connectors Using a Cartridge-Type Cleaner ......................................................................................83
Cleaning Fiber Optic Connector Using a Swab ....................................................................................................................85
Figure 2. AT-2814FX LED ...................................................................................................................................................17
Figure 10. Selecting the PCI ExpressCard Slot...................................................................................................................34
Figure 11. Pressing the Button ............................................................................................................................................34
Figure 12. The Button and Plate after Pressing the Button .................................................................................................35
Figure 13. Removing the Plate ............................................................................................................................................35
Figure 14. Attaching the Stabilizer to the AT-2814FX ExpressCard....................................................................................36
Figure 15. Inserting the Unit into the 54mm Slot .................................................................................................................36
Figure 16. System Properties Window on Windows XP......................................................................................................43
Figure 17. Hardware Page on Windows XP ........................................................................................................................44
Figure 18. Device Manager Window on Windows XP .........................................................................................................44
Figure 19. Device Manager with an Expanded List on Windows XP...................................................................................45
Figure 22. System Window on Windows Vista and 7 ..........................................................................................................47
Figure 23. Device Manager Window on Windows Vista and 7 ............................................................................................48
Figure 24. Device Manager with an Expanded List on Windows Vista & 7 .........................................................................48
Figure 25. Properties Window on Windows Vista and 7......................................................................................................49
Figure 26. Flow Control Page..............................................................................................................................................50
Figure 29. Large Send Offload (IPv4) Page .....................................................................................
Figure 30. Log Status Messages.........................................................................................................................................58
Figure 31. Max IRQ per Sec Page.......................................................................................................................................60
Figure 37. Wake From Shutdown Page...............................................................................................................................71
Figure 39. Device Manager Window with an Option List .....................................................................................................78
Figure 41. Ferrule in an SC Connector Plug........................................................................................................................82
Figure 42. Unclean and Clean Ferrule.................................................................................................................................82
Figure 44. Rubbing the Ferrule Tip on the Cleaning Surface ..............................................................................................83
Figure 45. Lint-Free and Alcohol-Free Swabs .....................................................................................................................85
Figure 46. Cleaning a Recessed Ferrule.............................................................................................................................85
...................................56
7
Figures
8
Tab le s
Table 1: Fiber Optic Port LED Status ..................................................................................................................................17
9
Tables
10
Preface
This manual is the installation and user’s guide for the AT-2814FX Fast
Ethernet Fiber (SC) ExpressCard. The instructions in this guide explain
how to install the ExpressCard on a laptop computer, install and uninstall
the driver software, and configure the driver software. This preface
contains the following sections:
“Safety Symbols Used in this Document” on page 12
“Contacting Allied Telesis” on page 13
11
Preface
Note
Caution
Warning
Warning
Safety Symbols Used in this Document
This document uses the following conventions:
Notes provide additional information.
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
Warnings inform you that performing or omitting a specific action
may result in bodily injury.
Warnings inform you that an eye and skin hazard exists due to the
presence of a Class 1 laser device.
12
Contacting Allied Telesis
If you need assistance with this product, you may contact Allied Telesis
technical support by going to the Support & Services section of the Allied
Telesis web site at www.alliedtelesis.com/support. You can find links for
the following services on this page:
24/7 Online Support - Enter our interactive support center to
search for answers to your questions in our knowledge database,
check support tickets, learn about Return Merchandise
Authorization (RMA), and contact Allied Telesis technical experts.
USA and EMEA phone support - Select the phone number that
best fits your location and customer type.
Hardware warranty information - Learn about Allied Telesis
warranties and register your product online.
Replacement Services - Submit an RMA request via our interactive
support center.
AT-2814FX Fast Ethernet Fiber (SC) ExpressCard Installation and User’s Guide
Documentation - View the most recent installation guides, user
guides, software release notes, white papers and data sheets for
your product.
Software Updates - Download the latest software releases for your
product.
For sales or corporate contact information, go to
www.alliedtelesis.com/purchase and select your region.
13
Preface
14
Chapter 1
Overview
This chapter provides an overview of the the AT-2814FX Fast Ethernet
Fiber (SC) ExpressCard in the following sections:
“Physical Description” on page 16
“Supported Operating Systems” on page 18
“Hardware Features” on page 19
“Contents of Your Shipment” on page 20
15
Chapter 1: Overview
Physical Description
The AT-2814FX ExpressCard is an integrated Fiber Fast Ethernet PCI
ExpressCard with a pair of SC fiber connectors based on Marvell 88E8059
chipset. A PCI ExpressCard is a new notebook interface that replaces the
PCMCIA Card Bus interface.
Using fiber optic cabling and a connector that meets 62.5/125 µm or 50/
125 µm multimode specifications, the AT-2814FX ExpressCard connects
a laptop computer to a Fast Ethernet network. The ExpressCard operates
at a speed of 100 Mbps in either full-duplex or half-duplex mode.
The AT-2814FX ExpressCard is shown in Figure 1.
Figure 1. AT-2814FX ExpressCard
PCI ExpressCardThe AT-2814FX ExpressCard has a 34mm-wide PCI ExpressCard
interface. You can install the AT-2814FX ExpressCard in a 34mm or
54mm PCI ExpressCard slot on your laptop computer.
SC Fiber
Connector
The faceplate on the AT-2814FX ExpressCard has a pair of SC fiber
connectors for attaching the ExpressCard to a compatible link partner.
One fiber optic connector is for transmitting and the other is for receiving.
Rubber PlugThe rubber plug prevents the fiber optic connectors from being exposed to
dust particles when the connectors are not used. Remove the rubber plug
before connecting them to the fiber optic cable.
16
AT-2814FX Fast Ethernet Fiber (SC) ExpressCard Installation and User’s Guide
LEDThe AT-2814FX ExpressCard has one LED as shown in Figure 2.
Figure 2. AT-2814FX LED
Table 1 describes the link states that the LED indicates.
Table 1. Fiber Optic Port LED Status
StateDescription
GreenThe port is operating at 100 Mbps and has a valid
link.
FlashingThe port is receiving or transmitting network packets
at 100 Mbps.
StabilizerThe stabilizer is a plastic bracket to help the ExpressCard snugly fit into
the 54mm PCI ExpressCard slot. Allied Telesis recommends utilizing the
stabilizer when installing the ExpressCard in the 54mm interface slot.
Figure 3. Stabilizer
17
Chapter 1: Overview
Note
Supported Operating Systems
The following operating systems are supported:
Windows XP
Windows Vista
Windows 7
Linux 2.6
When new driver software is released, they will be posted on the Allied
Telesis website: www.alliedtelesis.com/support/software/.
The procedures for Installing the driver software for the Linux
operating system is not included in this manual.
18
Hardware Features
AT-2814FX Fast Ethernet Fiber (SC) ExpressCard Installation and User’s Guide
The AT-2814FX ExpressCard supports the following features:
One 100BASE-FX port with a pair of SC multi-mode fiber connectors
Full and half duplex Media Access Control (MAC)
Link/Activity LED
PCI ExpressCard Interface
Flow control (IEEE 802.3x)
CPU interrupt control
Jumbo packet
IPv4 large send offload and checksum offload
Log message selection
Receive buffer
Transmit buffer
19
Chapter 1: Overview
Note
Contents of Your Shipment
The following items are included with your AT-2814FX ExpressCard:
Antistatic bag
The ExpressCard is shipped in an antistatic bag. It protects the card
when stored or shipped. Keep the card in its packaging until ready for
installation.
Rubber plug
The rubber plug prevents the fiber optic connectors from being
exposed to dust particles. Cover the connectors when the fiber optic
connectors are not used.
Stabilizer
When installing the AT-2814FX ExpressCard into the 54mm PCI card
slot of your laptop computer, attach the stabilizer to your AT-2814FX
ExpressCard.
The AT-2814FX ExpressCard is not shipped with a software driver
CD. You must download the driver software from the Allied Telesis
website. See Chapter 2, “Downloading the Driver Software” on page
23.
Inform your network supplier of any missing or damaged items. If you
need to return the ExpressCard, you must pack it in the original (or
equivalent) packing material or the warranty will be voided. See
“Contacting Allied Telesis” on page 13.
The product documentation is available in Portable Document Format
(PDF) on our web site at www.alliedtelesis.com/support/software/. You
can view the documents online or download them onto a local workstation
or server.
20
Chapter 2
Note
Installing the Driver Software
This chapter describes how to install driver software for the AT-2814FX
ExpressCard onto your operating system. It contains the following topics:
“Overview” on page 22
“Downloading the Driver Software” on page 23
“Installing the Driver Software” on page 24
To set Advanced Properties, see Chapter 4, “Modifying Advanced
Properties” on page 41.
21
Chapter 2: Installing the Driver Software
Overview
GuidelinesHere are the guidelines to installing the driver software on your operating
To install the driver software, you must download the driver software for
the AT-2814FX ExpressCard from the Allied Telesis website onto your
operating system.
Allied Telesis recommends installing the driver software for the AT2814FX ExpressCard before physically installing the card.
system:
To install the driver software, you must have administrative privileges.
When you install the AT-2814FX ExpressCard before installing the
driver software, the Windows system detects a new adapter and may
install a default driver. To update the driver software for the AT2814FX ExpressCard, follow the instructions as described in
“Downloading the Driver Software” on page 23 and “Installing the
Driver Software” on page 24.
When you install the AT-2814FX ExpressCard before installing the
driver software, the Windows system may install the native Marvell
driver if your laptop has an onboard Marvell network interface. To
update the driver for the AT-2814FX ExpressCard, follow the
instructions as described in “Downloading the Driver Software” on
page 23 and “Installing the Driver Software” on page 24.
22
Downloading the Driver Software
The AT-2814FX ExpressCard is not shipped with a software driver CD.
You must download driver software from the Allied Telesis website.
To download driver software, do the following:
1. Open a web browser, such as Internet Explorer or FireFox, on your
system and enter the following:
http://www.alliedtelesis.com/support/software
2. The Allied Telesis Software Download page is displayed.
3. Enter “2814fx” in the search box and press the enter key.
The search result is displayed as shown in Figure 4.
.
AT-2814FX Fast Ethernet Fiber (SC) ExpressCard Installation and User’s Guide
Figure 4. Software Downloads Search Result
4. Click “AT-2814FX Drivers for Windows.”
5. Save the AT2814FX-drivers-setup zip folder onto your system and
record the location of the folder.
23
Chapter 2: Installing the Driver Software
Note
Installing the Driver Software
To install the driver software for the AT-2814FX ExpressCard, do the
following:
1. Locate the AT2814FX-drivers-setup zip folder that you downloaded
from the Allied Telesis website onto your system. See “Downloading
the Driver Software” on page 23.
2. Open the folder. Figure 5 shows an example in the Windows XP
operating system.
Figure 5. Setup File
3. Double-click the setup.exe file.
The User Account Control window appears, prompting you to allow the
Marvell Miniport Driver program to make a change on your system.
If you are using Windows XP operating system, the User Account
Control window does not come up. Go to step 5.
4. Click Yes to allow Marvell Miniport Driver to be installed.
24
AT-2814FX Fast Ethernet Fiber (SC) ExpressCard Installation and User’s Guide
The Marvell Miniport Driver Setup Wizard window comes up. See
Figure 6.
Figure 6. Marvell Miniport Driver Setup Wizard
5. Click Next.
The Licence Agreement window comes up as shown in Figure 7.
25
Chapter 2: Installing the Driver Software
Figure 7. Setup Wizard License Agreement
6. Read the License Agreement.
7. If you accept the terms of the agreement, select the first option and
click Install.
When the installation is completed, the Installation Complete window
is displayed. See Figure 8.
26
Figure 8. Installation Complete
8. Click Next.
The final Wizard windows comes up as shown in Figure 9 on page 27.
Loading...
+ 60 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.