Allied Telesis AT-2400, AT-2701, AT-2451, AT-2700, AT-2745 Installation Manual

...

Page 1

Network Adapter Cards

AT-2400 Series AT-2450/AT-2451 Series AT-2500/AT-2501 Series AT-2700/AT-2701 Series AT-2745/AT-2746 Series AT-2915 Series AT-2930 Series AT-2970/AT-2971 Series

Installation Guide

BOOK II

FOR MICROSOFT WINDOWS FOR WORKGROUPS

3.11, MICROSOFT DOS CLIENT 3.0, NOVELL NETWARE 4.X, 5.X, AND 6.X, LINUX 2.2X AND 2.4X, AND BOOT ROM OPERATING SYSTEMS

PN 613-50383-00 Rev B

Page 2

All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Netscape Navigator is a regist ered trademark of Netscape Communications Corporation. All other product names, company

names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesy n, Inc. re serves t he righ t to make change s in specifi cations a nd other informati on contai ned in t his docum ent wit hout

prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesyn, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesyn, Inc. has been advised of, known, or should have known, the possibility of such damages.

Page 3

Electrical Safety and Emission Statement

Standards: This product meets the following standards.

RFI Emission EN55022 Class A, EN61000-3-2, EN61000-3-3

" 1

Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

" 2

Immunity EN55024

" 3

Electrical Safety EN60950, UL 1950 (UL/cUL)

" 4

Laser EN60825

" 5

Important: Appendix B contains translated safety statements for installing this equipment. When you see the

", go to Appendix

B for the translated safety statement in your language. Wichtig: Anhang B enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn Sie

" sehen, schlagen Sie in

Anhang B den übersetzten Sicherheitshinweis in Ihrer Sprache nach. Vigtigt: Tillæg B indeholder oversatte sikkerhedsadvarsler, der vedrører installation af dette udstyr. Når De ser symbolet

", skal

De slå op i tillæg B og finde de oversatte sikkerhedsadvarsler i Deres eget sp rog. Belangrijk: Appendix B bevat vertaalde veiligheidsopmerkingen voor het installeren van deze apparatuur. Wanneer u de

" ziet,

raadpleeg Appendix B voor vertaalde veiligheidsinstructie s in uw taal. Important: L'annexe B contient les instructions de sécurité relatives à l'installation de cet équipement. Lorsque vous voyez le

symbole

", reportez-vous à l'annexe B pour consulter la traduction de ces instructions dans votre langue.

Tärkeää: Liite B sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet. Kun näet

"-symbolin, katso käännettyä

turvaohjetta liitteestä B. Importante: l’Appendice B contiene avvisi di sicurezza tradotti per l’installazione di questa apparecchiatura. Il simbolo

", indica

di consultare l’Appendice B per l’avviso di sicurezza nella propria lingua. Viktig: Tillegg B inneholder oversatt sikkerhetsinformasjon for installering av dette utstyret. Når du ser

", åpner du til Tillegg B

for å finne den oversatte sikkerhetsinformasjonen på ønsket språk. Importante: O Anexo B contém advertências de segurança traduzidas para instalar este equipamento. Quando vir o símbolo

leia a advertência de segurança traduzida no seu idioma no Anexo B. Importante: El Apéndice B contiene mensajes de seguridad traducidos para la instalación de este equipo. Cuando vea el símbolo

", vaya al Apéndice B para ver el mensaje de seguridad traducido a su idioma.

Obs! Bilaga B innehåller översatta säkerhetsmeddelanden avseende installationen av denna utrustning. När du ser

", skall du gå

till Bilaga B för att läsa det översatta säkerhetsmeddelandet på ditt språk.

U.S. Federal Communications Commission

Radiated Energy

Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a res identia l area is li kely to caus e harmful inte rference in which case t he user will be required to correct the interference at his own expense.

Note: Modifications or changes not expressly approved by the manufacturer or the FCC can void your right to operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Page 4

Page 5

Table of Contents

Electrical Safety and Emission Statement ...............................................................................................................................................3

Preface ......................................................................................................................................................................................................................9

Purpose of this Guide ...........................................................................................................................................................................................9

How This Guide is Organiz ed .................................................................................... .......................................................................................10

Where to Find Related Guides .........................................................................................................................................................................11

Document Conventions ................................................ ....................................................................................................................................12

Contacting Allied Telesyn Technical Support ................ ............................................................................................................................13

Online Support..............................................................................................................................................................................................13

Telephone Suppor t........ ..............................................................................................................................................................................13

E-mail Support..... ............................................................................... ...........................................................................................................13

Returning Products .............................................................................................................................................................................................14

For Sales or Corporate Information .......... ............................................................................... ......................................................................15

Tell Us What You Think ......................................................................................................................................................................................16

Chapter 1

Installing the Network Adapter Card .......................................................................................................................................................17

Verifying Package Contents......................................................................................................................................................................17

Reviewing Safety Precaut io ns .........................................................................................................................................................................18

Installing a Network Adapter Card ................................................................................................................................................................19

Chapter 2

Diagnostics ...........................................................................................................................................................................................................23

Running Diagnostics ...........................................................................................................................................................................................24

For the AT-24xx, AT-25xx, AT-27xx, AT-2915, and AT-2930 Series............................... ................................. .............................24

For the AT-2970 and AT-2971 Series............................. ............................. ...........................................................................................25

Loopback Test for Fiber Adapt e rs ................................................... .......................................................................................................26

Repeater Test for Coppe r Adapters............................................ ...........................................................................................................28

Failure of a Test....... ......................................................................................................................................................................................30

Additional Functions of th e Diagnostics Program ............... ....................................................................................................................32

Checking Other Displays and Data ........................................................................................................................................................32

Main Program................................................................................................................................................................................................32

Reading Sensor Data...................................................................................................................................................................................33

Reading Configuration Data.....................................................................................................................................................................34

Reading VPD Data........................................................................................................................................................................................35

Page 6

Chapter 3

Microsoft DOS Client 3.0 ................................................................................................................................................................................37

Installing a Network Adapter Driver .............................................................................................................................................................38

Sample Configuration.................... ............................................................................................................................................................39

Removing a Network Adapter Driver ...........................................................................................................................................................40

Chapter 4

Microsoft Windows for Workgroups .......................................................................................................................................................41

Installing a Network Adapter Driver .............................................................................................................................................................42

Installing NDIS3, NDIS2, ODI Drivers..................................................................................................................................................... 42

Sample PROTOCOL.INI Fi le... ....................................................................................................................................................................44

NetWareIPXODI Support fo r NetWare 3.x.................... .......................................................................................................................45

NetWare IPXODI Support For NetWare 4.x......................................................................................................................................... 46

Sample NET.CFG and PROTOCOL.INI Files..........................................................................................................................................47

Removing a Network Adapter Driver ...........................................................................................................................................................48

Chapter 5

Novell Netware ...................................................................................................................................................................................................49

Installing a Network Adapter Driver on Novell Netware 4 Server .....................................................................................................50

Files Needed for Installation....................................................................................................................................................................50

New Server Installation..............................................................................................................................................................................50

Installing the Drivers............... ..................................................... ...............................................................................................................51

Multiple Adapters........................................................................................................................................................................................53

Removing an Adapter Driver from Novell Netware 4 Server.......................................................................................................54

Installing a Network Adapter Driver on Novell NetWare 5.x/ 6.x ........................................................................................................55

Files Needed for Installation....................................................................................................................................................................55

New Server Installation..............................................................................................................................................................................55

Manual Installation......................................................................................................................................................................................56

Removing an Adapter Driver from Novell Netware 5/6 Server...................................................................................................59

Chapter 6

Linux ........................................................................................................................................................................................................................ 61

Installing the ATNIC Driver for AT-2450/AT-2451, AT-2700/ AT-2701 Series,

and AT-2745/AT-2746 Series PCI Ethernet Adapters .............................................................................................................................. 62

Limitations......................................................................................................................................................................................................62

Building the Driver ......................................................................................................................................................................................62

Installing the Driver................................................................................................... ..................................................................................62

Dynamic Loading.........................................................................................................................................................................................62

Changing Configuration Settings.......................................................................................................................................................... 63

Installing a Linux Driver for an AT-2915 and AT-2930 Series Network Adapter ........................................................................... 64

Module Parameters.....................................................................................................................................................................................65

Installing Linux on a AT-297 0 or AT-2971 Series Adapters ...................................................................................................................67

Overview.........................................................................................................................................................................................................67

Required Files................................................................................................................................................................................................67

Installation Guidelines............................................................................................................................................................................... 67

Loading the Module Ma nu ally................................................................................................................................................................68

Unloading the Module...............................................................................................................................................................................68

Driver Parameters........................................................................................................................................................................................68

Page 7

Network Adapter Card Installation Guide

Chapter 7

BootROM ................................................................................................................................................................................................................69

Managed Boot Agent..................................................................................................................................................................................69

Installing a BootROM .............................................................. ............................................................................................................................71

Installation ......................................................................................................................................................................................................71

BootROM Parameter .............. .....................................................................................................................................................................73

Appendix A

Translated Safety and Emission Information ......................................................................................................................................75

Page 8

Page 9

Preface

This installation guide contains instructions on how to install an Allied Telesyn adapter card in your computer and how to load the adapter driver. This guide also explains the AT-Setup program which simplifies the task of installing or updating an adapter driver.

Purpose of this Guide

This guide is intended for anyone who needs to install or update a network adapter card or driver on their PC-compatible system.

Page 10

Preface

How This Guide is Organized

This guide contains the following chapters and appendix: Chapter 1, Installing the Network Adapter Card, describes how to insta ll

an adapter card into your computer. Chapter 2, Diagnostics, contains procedures for running and using the

diagnostics program for your Allied Telesyn adapter. Chapter 3, Microsoft DOS Client 3.0, contains procedures for manually

installing a network adapter driver on a PC-compatible system running Microsoft DOS Client 3.0.

Chapter 4, Microsoft Windows for Workgroups, contains the procedures for installing and removing a network adapter driver on a PC-compatible running Windows for Workgroups 3.11.

Chapter 5, Novell Netware, contains the procedures for installing an adapter driver on a Novell Netware system.

Chapter 6, Linux, contains the procedures for installing an adapter driver on a Linux system.

Chapter 7, BootROM, contains the procedures for installing and configuring a BootROM on an Allied Telesyn Network Adapter Card.

Appendix A, Translated Safety and Emission Information, contains multilanguage translations of the safety and emission statements in this guide.

Page 11

Network Adapter Card Installation Guide - Book II

Where to Find Related Guides

The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documentation, software updates, and technical information for all of our products. The documents provided on our web site are available as PDF files.

Page 12

Preface

Document Conven tions

This guide uses several conventions that you should become familiar with before you begin to install the product.

Note

Notes provide additional information.

Warning

Warnings inform you that performing or omitting a specific action may result in bodily injury.

Caution

Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data.

Page 13

Network Adapter Card Installation Guide - Book II

Contacting Allied Telesyn Technical Support

You can contact Allied Teleysn technical support online or by telephone or e-mail.

Online Support You can request technical support online by accessing the Knowledge

Base at h

ttp://kb.alliedtelesyn.com. You can use the Knowledge Base to

submit questions to our technical support staff and review answers to previously asked questions.

Telephone

Support

For technical support by phone, contact Allied Telesyn at one of the following locations:

E-mail Support Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands

latin_america@alliedtelesyn.com United Kingdom, Sweden, Norway, Denmark, and Finland

support_europe@alliedtelesyn.com

Americas

United States, Canada, Mexico, Central America, South America Tel: 1 (800) 428-4835

Germany

Germany, Switzerland, Austria, Eastern Europe Tel: (+49) 30-435-900-12 6

Asia

Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Philippines, China, India, Hong Kong Tel: (+65) 3815-612

Italy

Italy, Spain, Portugal, Greece, Turkey, Israel Tel: (+39) 02-41-30-41

Australia

Australia, New Zealand Tel: 1 (800) 000-880

Japan

Tel: (+81) 3-3443-5640

France

France, Belgium, Luxembourg, Th e Netherlands, Middle East, Africa Tel: (+33) 1-60-92-15-25

United Kingdom

United Kingdom, Denmark, Norway , Sweden, Finland, Iceland Tel: (+44) 1-235-442560

Page 14

Preface

Returning Products

Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense.

To obtain an RMA number, contact technical support at one of the following locations:

❑ United States and Canada

Toll-free: 1-800-762-1664 Fax: 1-425-806-1050

❑ Europe, Africa, and the Middle East

Tel: +44-1793-501401 Fax: +44-1793-431099

❑ Latin America, the Caribbean, an d Virgin Islands

Tel: International code + 425-481-3852 Fax: International code + 425-481-3895

❑ Puerto Rico

Toll-free: 1-800-424-5012, ext 3852 or 1-800-424-4284, ext 3852

❑ Mexico

Toll-free: 800-424-5012, ext 3852 Fax: International code + 425-481-3895

❑ Asia and Southeast Asia

Tel: +65 381-5612 Fax: +65 383-3830

❑ Australia

Toll-free: 1-800-000-880 Fax: 2-9438-4966

❑ New Zealand

Toll-free: 0800-45-5782

Page 15

Network Adapter Card Installation Guide - Book II

For Sales or Corporate Information

You can contact Allied Telesyn for sales or corporate information at the location listed below:

Allied Telesyn, Inc.

19800 North Creek Parkway, Suite 200 Bothell, WA 98011 Tel: 1 (425) 487-8880 Fax: 1 (425) 489-9191

Page 16

Preface

Tell Us What You Think

If you have any comments or suggestions on how we might improve this or other Allied Telesyn documents, please fill out the General Enquiry Form online. This form can be accessed by selecting Contact Us from

www.alliedtelesyn.com.

Page 17

Chapter 1

Installing the Network Adapter Card

This chapter contains instructions for installing the following Allied Telesyn network adapter cards:

❑ AT-2400 Series ❑ AT-2450/AT-2451 Series ❑ AT-2500/AT-2501 Series ❑ AT-2700/AT-2701 Series ❑ AT-2745/AT-2746 Series ❑ AT-2915 Series ❑ AT-2930 Series ❑ AT-2970/AT-2971 Series

Verifying Package

Contents

Make sure the following items are included in your package. If any item is missing or damaged, contact your Allied Telesyn sales representative for assistance.

❑ Allied Telesyn Network Adapter Card ❑ CardAssistant CD ❑ Wake-on-LAN cable (AT-2450, AT-2451, AT-2500, AT-2501,

AT-2700, and AT-2701 Series only)

Page 18

Installing the Network Adapter Card

Reviewing Safety Precautions

Please review the following safety precautions before you install the network adapter card.

Warning

This is a “Class 1 LED product”. " 6

Warning

Do not stare into the laser beam. (AT-2450FT, AT-2450FL, AT -2451FTX,

AT-2700FX, AT-2701, AT-2970, AT-2971SX Series only) " 7

Warning Lightning Danger: Do not work on this equipment or cables during

periods of lightning activity. " 8

Caution

Operating Temperature: This pro duct is designed for a maximum

ambient temperature of 40 degrees C. " 9

Caution

All Countries: Install this product in accordance with local and

National Electric Codes. " 10

Page 19

Network Adapter Card Installation Guide - Book II

Installing a Network Adapter Card

This section explains how to install a network adapter card in most PCcompatible computers.

To install the adapter card, perform the following procedure:

1. Shutdown your PC and disconnect the power cord from the outlet.

2. Remove the PC’s cover by removing the screws from the chassis and

gently sliding off the cover. See Figure 1.

Figure 1 Removing the PC Cover

3. Select an empty, non-shared PCI slot and remove the faceplate.

Keep the faceplate in a safe place. You may need it for future use. See Figure 2.

Figure 2 Removing the Faceplate From PCI Slot

Note

If you cannot locate or know how to find an PCI slot, refer to the documentation that came with your PC.

Page 20

Installing the Network Adapter Card

4. Remove the network adapter card from the shipping package and store the packaging material in a safe location.

Caution

Wear a grounding device and observe electrostatic discharge precautions when installing the network adapter card in a PC. Failure to observe this caution could result in damage to the adapter card.

5. Gently insert the network adapter card into the PCI slot. Make sure the card is securely seated.

Figure 3 Inserting the Network Adapter Card

6. Secure the network adapter card to the chassis with a Phillips-head screw, not provided.

Figure 4 Securing the Adapter Card

Page 21

Network Adapter Card Installation Guide - Book II

7. For the AT-2450, AT-2500, or AT-2700 Series adapters, to use the adapter card’s Wake-on-LAN feature in your computer using an Advanced Configuration and Power Interface (ACPI), you must connect the Wake-on-LAN cable to the Wake-on-LAN connector on the adapter card and to the Wake-on-LAN connector on the motherboard of the computer. For the location of the Wake-on-LAN connector on the motherboard, refer to the documentation that came with your computer.

The AT-2501, AT-2451F, AT-2701, AT-2915, AT-2930, AT-2970, and AT-2971 do not require the optional external Wake-on-LAN cable. These devices are PCI 2.2 compliant and can use the PCI 2.2 BUS for Wake-on-LAN features.

8. Replace the PC’s cover and secure it with the screws removed in

Step 2.

9. Connect the adapter card to the network by connecting the appropriate data cable.

10. Power ON the PC.

You are now ready to install the network adapter driver. Refer to the appropriate chapter for your operating system.

Page 22

Page 23

Chapter 2

Diagnostics

This chapter contains the following procedures:

❑ Running Diagnostics on page 24 ❑ Additional Functions of the Diagnostics Program on page 32

Page 24

Diagnostics

Running Diagnostics

For the AT-24xx,

AT-25xx, AT-27xx,

AT-2915, and

AT-2930 Series

The diagnostics utulity is useful for setting the Speed/Duplex and BootROM. You can also insure proper operation of the network adapter card. This utility is located on the CardAssistant CD or the driver installation disk.

Speed/Duplex

This option allows the user to configure speed and duplex to one of the available options. The options for speed and duplex vary depending on adapter model

BootROM Port

The BootROM port setting is only for multi-port AT-2450, AT-2700, and AT-2745 Series PCI Ethernet Adapter Cards without integrated Manage BootROM, specifically the AT-2450FTX, AT-27 00FT X, and AT-2745FX. When using one of these three adapters in a BootROM configuration, it may be necessary to change these settings. For any other AT-2450 or AT-2700 Series PCI Ethernet Adapter Card the BootROM Port setting should not be changed.

BootROM

This feature is only available for the AT-2500 and AT-2501TX Series Adapters. Using the Diagnostics program (diag25.exe) set BootROM to enable.

Diagnostics

There are two diagnostic utilities, Card Test and Network Test.

❑ Card Test

This test checks several parts and functions of the adapter card to ensure proper operation of the adapter card.

❑ Network test

This test allows the user to send and receive raw packets without a driver loaded to check the card functionality.

Page 25

Network Adapter Card Installation Guide - Book II

To run diagnostics, perform the following procedure:

Note

Diagnostics is a DOS based program and must be run in true DOS, not in a DOS shell within Windows.

1. If ON, power OFF your computer and reboot into DOS mode.

2. At the DOS prompt and without the drivers loaded, type diag.exe. The location of the diagnostic files on the CardAssistant CD are:

For example, if you want to run diagnostics for an AT-2500 Series adapater card and the CD is mapped to drive D, you would enter:

D:\drivers\at2500\diag\diag25.exe

If you are using a driver installation disk, the diagnostic files are stored in the root directory on the disk.

For the AT-2970

and AT-2971

Series

Diagnostics Program The network adapter can be tested with the supplied diagnostics

program (running DOS). The diagnostics program run offline, for example, normal operation of the network adapter can not be maintained. During testing the link of the tested port will be down, for examle, no data can be transferred. The following test are available:

❑ Simple test without loopback

This test covers all components but not the port (socket including components for transmitting/receiving the data signals).

❑ Comprehensive port test with loopback

All componentes are tested, including the port.

Adapter Card Diagnostic Location

AT-2400 Series \drivers\at2400\diag\diag2 4. exe AT-2500, AT-2501 Series \drivers\at2500\diag\diag25.exe AT-2450, AT-2700,

AT-2701, AT-2745, AT-2746 Series

\drivers\at2701\diag\diag.exe

AT-2915, AT-2930 Series \drivers\at29xx\diag\diag29.exe

Page 26

Diagnostics

Note

The tests do not run in a Windows DOS box.

The location of the diagnostic file on the CardAssistant CD is:

Loopback Test

for Fiber Adapters

To perform the loopback test on fiber adapters, you will need a loopback connector. Refer to Figure 5 below.

Figure 5 Setup for Loopback Testing

Be sure to observe the Translated Safety and Emission Information on page 75.

To test the adapter, perform the following procedure:

1. Power OFF your computer.

2. If the computer is still connected to the network, unplug the data cable from the network adapter’s port.

3. Connect the network adapter as follows:

❑ For the simple test, insert the protective plugs into the ports. ❑ For the loopback test, insert the loopback connector into the

port.

4. Boot to DOS. Wait until the operating system is loaded and the DOS prompt is displayed.

5. Insert the CardAssistant CD into the CD-ROM drive.

6. Go to the product directory and type diag2971.

7. Press <Enter>.

Adapter Card Driver Location

AT-2970, AT-2971 Series \drivers\at2971\diag\diag2971.exe

Page 27

Network Adapter Card Installation Guide - Book II

8. From the Main Menu of the diagnostics program, select one of the following:

❑ DIAGNOSTICS for the simple test (no loopback) ❑ LOOPB. WRAP PLUG for the loopback test

The various components will now be tested. This will take between one and two minutes. If the test was successful, a window similar to Figure 6 will be displayed.

Figure 6 Diagnostic Window (1 of 5) You can follow the progress of the test in the right-hand window.

Each test is displayed as it is being performed (e.g. Board Register Check).

If the test is successful, the word PASSED is displayed at the end of the line and the next test is started. If there is a problem, the word Failed is displa yed.

If errors are reported, follow the instructions that are provided.

9. Check the configuration and if necessary, repeat the test (see Failure of a Test).

10. To continue testing, press any key.

11. To quit the diagnostics program, select Exit from the Main Menu.

Page 28

Diagnostics

12. Remove the loopback connector from the port.

13. Re-connect the data cables to the network port.

Caution

For safety reasons, if the adapter is not connected immediately to the data network, insert the protective plug. Otherwise laser light may be emitted. Inserting the protective plug is also protects the port against dust and dirt.

Repeater Test for

Copper Adapters

For the AT-2970 and AT-2971 Series adapters the test via wrap plug is not available. However, loopback testing may be carried out by connecting the adapter to another adapter installed in a second computer running in repeater mode (further known as the repeater computer). The computer in which the adapter is installed, which is to be tested, is called test computer.

To test the copper adapter, perform the following procedure:

1. Install a copper adapter in the repeater computer.

2. Boot the repeater computer to DOS. Wait until the operating system is loaded and the DOS prompt is

displayed.

3. Insert the CardAssistant CD into the CD-ROM drive.

4. Go to the product directory and type diag2971.

5. Press <Enter>.

6. From the Main Menu of the diagnostics program, select Repeater Mode.

7. Select the port which is to be tested, for example, A (for single link adapters, only A is available).

8. Press <Enter>. The window Repeater Mode Port A is displayed.

9. Install a copper adapter in the test computer.

10. Connect the adapter in the repeater computer to the adapter in the test computer. Use a category 5 cable with RJ-45 plugs.

11. Boot the test computer to DOS. Wait until the operating system is loaded and the DOS prompt is

displayed.

Page 29

Network Adapter Card Installation Guide - Book II

12. Insert the CardAssitant CD into the CD-ROM drive.

13. Go to the product directory and type diag2971.

14. Press <Enter>.

15. From the Main Menu of the diagnostics program, select LOOPB.WRAP PLUG.

16. Press <Enter>. When the test was successful, the message All tests passed

successfully is dis-played. When the test fails, the message failed is displayed. The further

procedure is described in section Failure of a Test.

17. Press any key to continue.

18. On the test computer, select Exit to quit the diagnostics program.

19. On the repeater computer, select Exit to quit the diagnostics program.

Page 30

Diagnostics

Failure of a Test

Figure 7 Diagonstic Window (2 of 5)

For a test to be completed successfully, each of the following conditions must be met:

❑ The network adapter operates correctly. ❑ The network adapter is cabled correctly for the test or is equipped

with the correct connectors.

❑ The network adapter has been installed correctly in the computer.

The failed message does not necessarily imply that the network adapter is faulty.

If a failed message is displayed, perform the following procedure:

1. Follow the instructions that are displayed in the window below the list of tests.

2. Make sure that the adapter is inserted correctly and the ports are connected properly (connectors are firmly seated, the correct end of the cable is connected).

Page 31

Network Adapter Card Installation Guide - Book II

If it is necessary to install the network adapter again, perform the following procedure:

1. Switch OFF the computer. Be sure to observe the Translated Safety

and Emission Information on page 75.

2. Remove the computer cover. Refer to the manual that came with your computer for instructions or refer to Installing the Network

Adapter Card on page 17.

3. Make sure the network adapter is properly seated in the PCI bus slot on the motherboard. If not, do not remove the network adapter completely but raise it sufficiently to withdraw it from the PCI bus slot.

4. Carefully realign the bus connector on the network adapter with the PCI bus slot.

5. Press the network adapter until it is firmly seated in the slot.

6. Repeat to Step 6 of the Loopback Test for Fiber Adapters on page 26 and to Step 4 of the Repeater Test for Copper Adapters on page 28.

7. Repeat the test.

8. To quit the diagnostics program, select EXIT in the Main Menu.

9. If necessary, remove the loopback connector from the port.

10. Re-connect the data cables to the network ports.

Page 32

Diagnostics

Additional Func tions of the Diagnostics Program

Checking Other

Displays and

Data

In addition to performing the three network adapter tests, the diagnostics program can also read out network adapter-specific data that may be useful for pinpointing the causes of failure.

You can:

❑ read sensor data ❑ read configuration data ❑ read and write VPD data ❑ read and write Flash EPROM data

Main Program To start the main program, proceed as follows:

1. Boot to DOS and wait for the prompt.

2. Insert the installation CD-ROM into the CD-ROM drive of the computer in which the network adapter is installed.

3. Type the letter of your CD-ROM drive (for example, D:)

4. Go to the appropriate product directory and type diag2971.

5. Press <Enter>.

Page 33

Network Adapter Card Installation Guide - Book II

The Main Menu as shown in Figure 8 is displayed:

Figure 8 Diagnostic Window (3 of 5)

6. Select the appropriate item from the menu.

7. To quit the program, select EXIT in the Main Menu. This option is automatically offered for selection if you did not select

a menu item previously.

Reading Sensor

Data

To read sensor data, perform the following procedure:

1. Start the main program. Refer to Main Program on page 32 for instructions.

2. Select Show Sensors in the Main Menu. A separate window will be displayed for the following sensor data:

❑ Temperature of the board ❑ Voltage on the PCI card ❑ Voltage on the PCI I/O lines ❑ Other supply voltages

In the Main Menu, Show Sensors changes to Hide Sensors.

Page 34

Diagnostics

3. You can close the window by selecting Hide Sensors from the Main Menu.

Other windows may be opened while this window is still open, for example, the window displaying the configuration data.

Reading

Configuration

Data

To read configuration data, perform the following procedure:

1. Start the main program. Refer to Main Program on page 32 for instructions.

2. Select SHOW CONFIGURATION in the main menu. A separate window will be di splayed showing:

❑ Device code (Device) ❑ Various vendor codes (Vendor) ❑ Interrupt no. (IRQ) ❑ Cache Line Size (CLS) ❑ Latency (Lat.) ❑ RAM size (RAM) ❑ PCI slot index and size (Slot and Slot size) ❑ PCI bus clock (clk) ❑ MAC address (MAC Addr) ❑ Port type (PMD-Type) ❑ Connector (connector) ❑ Hardware revision (HW Rev) ❑ Chip ID (Chip Id)

In the Main Menu, Show Configuration changes to Hide Configuration.

3. You can close the window by selecting Hide Configuration from the Main Menu.

Other windows may be displayed while this window is still open,for example, a window shown in Figure 9 will be displayed.

Page 35

Network Adapter Card Installation Guide - Book II

Figure 9 Diagnostic Window (4 of 5)

Reading VPD

Data

To read VPD data (Vital Product Data), perform the following procedure:

1. Start the main program. Refer to Main Program on page 32 for instructions.

2. Select VPD Data from the Main Menu. A submenu with the following options will be displayed:

❑ EXIT (return to the Main Menu) ❑ DISPLAY VPD DATA ❑ CLEAR ERROR LOGS ❑ ADD/MODIFY VPD DATA (you can enter user-defined data and

keywords here)

❑ DELETE VPD KEYWORDS

Page 36

Diagnostics

Figure 10 Diagnostic Window (5 of 5)

3. Select the desired option or return to the Main Menu by selecting Exit (default option).

Page 37

Chapter 3

Microsoft DOS Client 3.0

This chapter contains the following procedures for the AT-24xx, AT-25xx, and AT-2700 Series adapters:

❑ Installing a Network Adapter Driver on page 38 ❑ Removing a Network Adapter Driver on page 40

Page 38

Microsoft DOS Client 3.0

Installing a Network Adapter Driver

This section contains the procedure for installing a network adapter driver on a Microsoft DOS Client 3.0 system.

Note

Before starting with the installation procedure, make sure that the adapter is properly configured using setup25.EXE provided on the CardAssistant CD. If necessary, match the speed and duplex settings of the network card with the hub with which it is connected.

To install the network adapter driver, perform the following procedure:

1. Shut down Microsoft DOS Client 3.0 and power OFF the computer.

2. Install the network adapter card in the compute. Refer to the Network Adapter Card Installation Guide - Book I and to your computer’s installation manual.

3. Power ON the computer.

4. Start the setup utility provided by Microsoft to install and configure DOS Client v3.0.

5. At the Welcome screen, press Enter.

6. Choose the destination directory for the client files and press Return.

7. When prompted for the network adapter, choose Network adapter not shown on list below . . .

A prompt is displayed asking you to insert the OEM driver disk.

8. Insert the CardAssistant CD or the driver installation disk into the appropriate drive.

9. Type in the driver letter and path to the NDIS 2.0 driver and press Return.

If you are using the CD, the location of the adapter driver will differ depending on the type of adapter. Below are the driver locations on the CardAssistant CD:

Adapter Card Driver Location

AT-2400 Series \drivers\at2400\msclient AT-2500/AT-2501 Series

\drivers\at2500\msclient

Page 39

Network Adapter Card Installation Guide - Book II

If you are using a driver installation disk, the driver location is: \msclient.

For example, if you are using the CardAssistant CD and the CD driver is mapped to drive D and you are installing an AT-2500 Series adapter, you would enter D:\drivers\at2500\msclient.

10. Once you have entered the drive letter and path to the adapter driver and pressed Return.

The next screen will display the Allied Telesyn AT-250x PCI Ethernet Adapter.

11. Press Return to select the driver and proceed with the installation according to the Microsoft documentation.

Sample

Configuration

[network.setup25] version=0x3110 netcard=ATI$a2500,1,ATI$a2500,1 transport=tcpip,TCPIP lana0=ATI$a2500,1,tcpip

AT-2450, AT-2700 Series \drivers\at2701\msclient

Adapter Card Driver Location

Page 40

Microsoft DOS Client 3.0

Removing a Network Adapter Driver

This section contains the procedure for removing an adapter driver from a system running Microsoft Client 3.0.

To remove an adapter driver, perform the following procedure:

1. Start the Microsoft setup utility.

2. Select Change Network Configuration.

3. Select the network adapter whose driver you want removed from the system.

4. Click Remove.

Page 41

Chapter 4

Microsoft Windows for Workgroups

This chapter contains procedures the following procedures for the AT-24xx, AT-25xx, AT-2700 Series adapters:

❑ Installing a Network Adapter Driver on page 42 ❑ Removing a Network Adapter Driver on page 48

Page 42

Microsoft Windows for Workgroups

Installing a Network Adapter Driver

This section contains the instructions for manually installing a network adapter driver on a PC running Windows for Workgroups 3.11.

Installing NDIS3,

NDIS2, ODI

Drivers

1. Power OFF the computer.

2. Install the network adapter card. Refer to the Network Adapter Card Installation Guid e - Book I and the documentation that came with your computer.

3. Power ON the computer.

4. From the Network group under Program Manager, choose Network Setup.

5. Select Networks.

6. Verify that Install Microsoft Windows Network is selected, then select OK.

7. Select Sharing.

8. Select whether to allow file and/or printer sharing with other users.

9. Select Drivers.

10. Select Add Adapt e r .

11. Select Unlisted or Updated Network Adapter, then click OK.

12. Insert the CardAssistant CD into the CD drive or a Driver Installation Disk into a floppy drive.

13. In the text box of the Install Driver dialog box, enter the drive letter and path to the driver files and click OK.

If you are using the CD, the location of the appropriate driver will differ depending on the type of adapter. Below are the driver locations on the CardAssistant CD:

Adapter Card Location

AT-2400 Series \drivers\at2400 AT-2500/AT-2501 Series \drivers\at2500 AT-2450 Series, AT-2700

Series

\drivers\at2701\wfw

Page 43

Network Adapter Card Installation Guide - Book II

If you are using a Driver Installation Disk, the driver location is the root (\) directory.

14. In the Network Adapters list of the Unlisted or Updated Network Adapter dialog box, verify that Allied Telesyn PCI Ethernet Adapter is highlighted, then click OK.

15. In the Network Drivers dialog box, verify that Allied Telesyn PCI Ethernet Adapter and its default protocols, Microsoft NetBEUI and IPX/SPX Compatible Transport with NetBIOS, appear in the Network Drivers list, then click Close.

16. In the Network Setup dialog box, click OK.

17. If prompted, insert the required Windows for Workgroups diskette(s) into your floppy drive and click OK.

Note

Windows for Workgroups occasionally lose s its place at this point; if you get a message from Windows that it cannot find a file, try inserting Windows for Workgroups installation diskettes 7 and 8.

18. If prompted, reinsert the CardAssistant CD or Driver Installation Disk into the appropriate drive.

19. In the text box of the Install Driver dialog box, click OK.

20. From the Windows Setup dialog box, select Restart Computer.

Page 44

Microsoft Windows for Workgroups

Sample

PROTOCOL.INI

File

[network.setup] version=0x3110 netcard=ms$a2500,1,MS$a2500,3 transport=ms$nwlinknb,NWLINK transport=ms$ndishlp,MS$NDISHLP transport=ms$netbeui,NETBEUI lana0=ms$a2500,1,ms$netbeui lana1=ms$a2500,1,ms$nwlinknb lana2=ms$a2500,1,ms$ndishlp

[protman] DriverName=PROTMAN$ PRIORITY=MS$NDISHLP

[NWLINK] BINDINGS=MS$a2500

[MS$NDISHLP] DriverName=ndishlp$ BINDINGS=MS$a2500

[NETBEUI] DriverName=netbeui$ SESSIONS=10 NCBS=12 BINDINGS=MS$a2500 LANABASE=0

[MS$a2500] DriverName=a2500$

[a2500] Adapters=MS$a2500

Note

These are the default values for installation. If you are adding any TCP/IP software, this configuration will satisfy the NDIS 2.0 requirements of TCP/IP systems.

Page 45

Network Adapter Card Installation Guide - Book II

NetWareIPXODI

Support for

NetWare 3.x

1. Create a new directory on your local hard drive (e.g.; C:\ATINET).

2. Copy the contents of the DOSODI directory on the CardAssistant CD or the Driver Installation Disk to the directory you created.

If you are using the CardAssistant CD, the location of the appropriate driver will differ depending on the type of adapter. Below are the driver locations on the CardAssistant CD:

If you are using a driver installation diskette, the driver location is \Dosodi.

3. Verify that the ODI drivers for the AT-2500/AT-2501 Ethernet Adapter Card are NOT loaded before setting up Windows for Workgroups.

4. Start Windows.

5. Choose Network Setup from the Network group.

6. Select Networks.

7. Select Install Microsoft Windows Network, then Other.

8. Select Novell NetWare (Workstation Shell 3.X), then OK.

9. Select IPXODI.COM and LSL.COM (recommended), then OK.

10. Verify that ATI AT-xxxx[ODI/NDIS2] and its default protocols,

Microsoft NetBEUI and IPX/SPX Compatible Transport with NetBIOS, appear in the Network Drivers list, then OK.

11. When asked if you want to modify the net.cfg file, you can enter the path to the directory created earlier for your ODI files (e.g.;C:\ATINET). After you make your changes, or if you do not want to make changes, click OK.

12. From the Windows Setup dialog box, select Continue.

13. Edit the Autoexec.bat file by inserting the following file references before C:\WINDOWS\odihlp.exe:

Adapter Card Location

AT-2400 Series \drivers\at2400\Dosodi AT-2500/AT-2501 Series \drivers\at2500\Dosodi AT-2450 Series, AT-2700

Series

\drivers\at2701\Dosodi

Page 46

Microsoft Windows for Workgroups

c:\ net\lsl c:\net\a2500 (atnic,a2400)

c:\net\ipxodi c:\net\netx

14. Exit Windows and re-boot your PC by powering OFF then ON.

NetWare IPXODI

Support For

NetWare 4.x

1. Verify that the ODI drivers for the AT-2500/AT-2501 Ethernet Adapter Card are NOT loaded before setting up Windows for Workgroups.

2. From the DOS command line, install the NetWare DOS/Windows Client software. Select Yes to install Windows support and then enter the path to your Windows directory, for example, C:\WINDOWS

3. Start Windows.

4. Select Network Setup from the Network group.

5. select Networks.

6. Select Install Microsoft Windows Network, then select Other.

7. From the Other drop down list, select Novell NetWare (Workstation Shell 4.0 and above) and click OK.

8. Select IPXODI.COM and LSL.COM (recommended), then OK.

9. In the Network Drivers dialog box, verify that ATI AT-xxxx

[ODI/NDIS2] and its default protocols, Microsoft NetBEUI and IPX/SPX Compatible Transport with NetBIOS, appear in the

Network Drivers lis and then click OK.

10. From the Windows Setup dialog box, select Restart Computer. Installing Novell NetWare 3.x and 4.x support adds

DEVICE=C:\WINDOWS\IFSHLP.SYS to your CONFIG.SYS file and C:\WINDOWS\ODIHLP.EXE to your AUTOEXEC.BAT file.

Note

The sample AUTOEXEC.BAT shows VLM.EXE being used instead of NETX.EXE. VLMs are required for NetWare 4.x but may be an alternative to NETX with NetWare 2.x and 3.x.

Page 47

Network Adapter Card Installation Guide - Book II

Sample

NET.CFG and

PROTOCOL.INI

Files

NET.CFG Preferred Server = MyServer Link Driver a2500 LineSpeed 100F (optional)

Frame Ethernet_802.3 Frame Ethernet_II Frame Ethernet_802.2 Frame Ethernet_SNAP

VLM Support NETWARE DOS REQUESTER

FIRST NETWORK DRIVE=F PROTOCOL.INI [network.setup]

version=0x3110 netcard=ms$a2500,1,MS$a2500,4 transport=ms$netbeui,NETBEUI transport=ms$nwlinknb,NWLINK lana0=ms$a2500,1,ms$nwlinknb lana1=ms$a2500,1,ms$netbeui

[MS$a2500] [NETBEUI]

BINDINGS=a2500 LANABASE=1

[net.cfg] PATH=C:\NET\net.cfg

[Link Driver a2500] data=Frame Ethernet_SNAP data=Frame Ethernet_802.2 data=Frame Ethernet_II data=Frame Ethernet_802.3 data=Link Driver a2500

[NWLINK] BINDINGS=a2500

Page 48

Microsoft Windows for Workgroups

Removing a Network Adapter Driver

This section contains the procedure for removing a network adapter driver from a system running Microsoft Windows for Workgroups 3.11.

The initial installation copies the OEMSETUP.INF to your WINDOWS\SYSTEM directory. It renames the file to OEMx.INF, where x is a number starting with 0 for drivers that are not shipped with Windows for Workgroups; this also pertains to video and printer drivers.

1. Click the Network Icon in the Network Control panel.

2. Select the Drivers button in Network Setup.

3. Select the Remove button.

4. Select Yes when asked if you want to remove the driver.

Page 49

Chapter 5

Novell Netware

This chapter contains the following procedures:

❑ Installing a Network Adapter Driver on Novell Netware 4 Server on

page 50

❑ Installing a Network Adapter Driver on Novell NetWare 5.x/6.x on

page 55

Page 50

Novell Netware

Installing a Network Adapter Driver on Novell Netware 4 Server

This section contains the procedure for installing a network adapter driver on a system running Novell NetWare 4 Server.

Files Needed for

Installation

The .LDI file and the .LAN file for your adapter must be present to succesfully complete installation. The location for each Allied Telesyn adapter are as follows:

New Server Installation

1. Follow the directions provided by Novell to load the network drivers using the INSTALL.NLM program.

2. When the Install program prompts for the LAN driver, select Insert to specify a driver not listed.

3. Insert the CardAssistant CD or driver installation disk into the appropriate drive.

4. Press <F3> to change the default path to A:\NETWARE. Press <Enter> as prompted. The adapter driver and other required files will be copied to the SYS: volume.

5. On the next menu, AT-2xxx Protocols and Parameters, specify any parameters where needed. A slot value is required when loading the adapter driver. If slot is unknown, driver will correctly detect slot value when loading.

6. Select Save parameters and load driver. The Netware 4.x driver has a PermaNet parameter that gives the Netware Server a redundancy mechanism where two network adapters are connected to the same local network. When the primary adapter fails, the secondary adapter then handles the network traffic until the primary adapter is restored. Proceed with the installation as outlined by Novell.

Adapter Card Location

AT-2400 Series \drivers\at2400\netware\ AT-2500/AT-2501 Series \drivers\at2500\netware\ AT-2450/AT-2451 Series,

AT-2700/AT-2701 Series, AT-2746 Series

\drivers\at2701\netware\

AT-2915 Series, AT-2930 Series

\drivers\at29xx\netware\

AT-2970, AT-2971 Series \drivers\at2971\netware\

1. For additional AT-2970 and AT-2971 parameter information, refer to the AT297x.txt file.

Page 51

Network Adapter Card Installation Guide - Book II

Installing the

Drivers

1. At the file server console prompt, issue the load statement(s) in this order:

LOAD <DRIVE>:<PATH>\NBI LOAD <DRIVE>:<PATH>\MSM LOAD <DRIVE>:<PATH>\ETHERTSM LOAD <DRIVE>:<PATH>\<DRIVER>

where <DRIVE> and <PATH> are the drive and directory where you copied the NLMs and the adapter file. <DRIVER> is the filename of the adapter driver.

Note

If MSM and ETHERTSM NLMs aren't loaded, they'll automatically load before the driver.

You will be prompted if you don't specify a SLOT number.

2. Next you must bind the LAN driver to IPX in order to attach to the server. Type:

BIND IPX TO <DRIVER> NET=n

Where <DRIVER> is the filename of the adapter driver and n is the node address Novell uses for routing IPX packets. This number is arbitrary if there is the only one server on the network, but if there are multiple servers on the same network, it must match the other servers' external network number.

Adapter Card Location

AT-2400 Series \drivers\at2400\netware\ AT-2500/AT-2501 Series \drivers\at2500\netware\ AT-2450/AT-2451 Series,

AT-2700/AT-2701 Series, AT-2746 Series

\drivers\at2701\netware\

AT-2915 Series, AT-2930 Series

\drivers\at29xx\netware\

AT-2970, AT-2971 Series \drivers\at2971\netware\

1. For additional AT-2970 and AT-2971 parameter information, refer to the AT297x.txt file.

Page 52

Novell Netware

Note

The default frame type for Novell file servers is now Ethernet_802.2. If you require Ethernet_802.3, specify FRAME=ETHERNET_802.3 on the command line when loading the driver.

To load multiple frame types for a single card, enter a LOAD and BIND statement for each frame type. You need to supply a name on each load line in order to avoid being prompted for which board to bind IPX to. If you do not have the name option in the AUTOEXEC.NCF, it will not execute completely without user intervention.

Example:

LOAD <DRIVER> FRAME=ETHERNET_802.3 NAME=IEE8023 BIND IPX TO IEE8023 NET=11111 LOAD <DRIVER> FRAME=ETHERNET_802.2 NAME=IEE8022 BIND IPX TO LAN8022 NET=22222

Where <DRIVER> is the filename of the adapter driver. Additionally, if you have a PCI-1 bus in your system, add

BUSTYPE=PCI1 to the command line, e.g., LOAD C:\SERVER.4\<driver> BUSTYPE=PCI1. Otherwise the driver may not find the card. If you don't know which bus you have, try loading without the option. If it loads, you do not need it.

3. Add the load and bind statements you require to the server's AUTOEXEC.NCF file so that the LAN driver will load automatically each time the server starts up.

Here's an example of how the commands would look in your AUTOEXEC.NCF file.

Example: LOAD a2500v3 FRAME=Ethernet_802.3 (overrides default frame

BIND IPX to a2500v3 net=1 (all servers on the LAN segment need the same #)

4. Proceed with the installation as outlined by Novell.

Page 53

Network Adapter Card Installation Guide - Book II

Multiple Adapters If a system has multiple Allied Telesyn Ethernet Adapters, you use the

keyword SLOT to identify each card to the driver. If you have multiple adapters in a single server, each adapter must have a different network number and SLOT number. Also, you might want to name each adapter. So add the options in LOAD commands to distinguish particular adapters. For example:

LOAD <DRIVER> FRAME=Ethernet_802.2 NAME=LAN_A SLOT=1 BIND IPX TO LAN_A NET=11 LOAD <DRIVER> FRAME=Ethernet_802.2 NAME=LAN_B SLOT=2 BIND IPX TO LAN_B NET=22

<DRIVER> is the filename of the adapter driver. Add the load and bind statements you need to the server's

AUTOEXEC.NCF file so that the Allied Telesyn adapter drivers load automatically each time the server starts.

In an IPX internal router configuration (a server with two adapters, each connected to a different network), the data transfer rate across the router can be low. This happens if client workstations have CPU speeds equal to or higher than the server. You might be able to increase the data transfer rate by adding the following line to STARTUP.NCF:

SET MAXIMUM INTERRUPT EVENTS = 100000

The default setting is 10. If you have problems loading the driver on multiple adapters and the

initialization fails due to "Insufficient RCBs," increase the number of buffers allocated to the server. Add the following to STARTUP.NCF:

SET MINIMUM PACKET RECEIVE BUFFERS = 100 (or larger) SET MAXIMUM PACKET RECEIVE BUFFERS = 500 (or larger)

The MINIMUM value you specify must be at least 30 times the number of Allied Telesyn PCI adapters in the computer.

Recommended settings: 1-3 adapters: 100

4 adapters: 150 The maximum you can specify depends on the amount of memory in

the server, but it must be greater than the minimum.

Page 54

Novell Netware

Removing an

Adapter Driver

from Novell

Netware 4 Server

This section contains the procedure for removing a network adapter driver from a system running Novell Netware 4 Server.

1. Type LOAD INSTALL at the server console to bring up the server installation module.

2. Select Driver Options and press Return.

3. Select Deselect a selected driver from the next menu and press Return. The highlight is moved to the installed adapter(s).

4. Press Return again to remove the selected driver.

Page 55

Network Adapter Card Installation Guide - Book II

Installing a Network Adapter Driver on Novell NetWare 5.x/6.x

This section contains the procedure for installing a network adapter driver on a system running Novell NetWare 5.x/6.x.

Files Needed for

Installation

The .LDI file and the .LAN file for your adapter must be present to succesfully complete installation. The location for each Allied Telesyn adapter are as follows:

New Server Installation

The NetWare 5 utility NWCONFIG provides the user with the abitlity to add additional network adapter cards. At the system console, type NWCONFIG

1. Select Driver Options then Configure Net w ork Driver.

2. Select an Additional Driver. The NWCONFIG displays a list of the available drivers.

3. Press <Insert> to specify a driver not listed.

4. Insert the CardAssistant CD or the Driver Installation Disk into the appropriate drive.

If you are using the CardAssistant CD, the names and locations of the adapter drivers are as follows:

Adapter Card Location

AT-2400 Series \drivers\at2400\netware\ AT-2500/AT-2501 Series \drivers\at2500\netware\ AT-2450/AT-2451 Series,

AT-2700/AT-2701 Series, AT-2745/AT-2746 Series,

\drivers\at2701\netware\

AT-2915 Series, AT-2930 Series

\drivers\at29xx\netware\

AT-2970, AT-2971 Series drivers\at2971\netware\

1. For additional AT-2970 and AT-2971 parameter information, refer to the AT297x.txt file.

Adapter Card Location

AT-2400 Series \drivers\at2400\netware\ AT-2500/AT-2501 Series \drivers\at2500\netware\

Page 56

Novell Netware

If you are using a Driver Installation Disk, the adapter driver will be located in the root directory.

5. Press <F3> to change the default path.

6. Press Return. The adapter driver and other required files are copied to the SYS:

volume.

7. On the next menu, Protocols and Parameters, specify any parameters where needed. A slot value is required when loading the adapter driver. If the slot is unknown, driver will correctly detect slot value when loading.

8. Select Save parameters and load driver.

9. Proceed with the installation as outlined in the Novell documentation.

Manual

Installation

1. At the file server console prompt, issue the load statement(s) in this order:

LOAD <DRIVE>:<PATH>\NBI LOAD <DRIVE>:<PATH>\MSM LOAD <DRIVE>:<PATH>\ETHERTSM LOAD <DRIVE>:<PATH>\<DRIVER>

Where <DRIVE> and <PATH> are the drive and directory where you copied the NLMs and the adapter driver file. <DRIVER> is the filename of t he driver.

Note

If MSM and ETHERTSM NLMs are not loaded, they will automatically load before the driver. You will be prompted if you do not specify a SLOT number.

AT-2450/AT-2451 Series, AT-2700/AT-2701 Series, AT-2745/AT-2746 Series,

\drivers\at2701\netware\

AT-2915 Series, AT-2930 Series

\drivers\at29xx\netware\

AT-2970, AT-2971 Series drivers\at2971\netware\

1. For additional AT-2970 and AT-2971 parameter information, refer to the AT297x.txt file.

Adapter Card Location

Page 57

Network Adapter Card Installation Guide - Book II

Type the following command to bind the LAN driver to IPX in order to attach to the server.

BIND IPX TO <DRIVER> NET=n

Where <DRIVER> is the filename of the driver and n is the node address Novell uses for routing IPX packets. This number is arbitrary if there is the only one server on the network, but if there are multiple servers on the same network, it must match the other servers' external network number.

Note

The default frame type for Novell file servers is now Ethernet_802.2. If you require Ethernet_802.3, specify FRAME=ETHERNET_802.3 on the command line when loading the driver.

Example:

LOAD <DRIVER> FRAME=ETHERNET_802.3 NAME=IEE8023 BIND IPX TO IEE8023 NET=11111 LOAD <DRIVER> FRAME=ETHERNET_802.2 NAME=IEE8022 BIND IPX TO LAN8022 NET=22222

<DRIVER> is the filename of the adapter driver. If you have a PCI-1 bus in your system, add BUSTYPE=PCI1 to the

command line (e.g., LOAD C:\SERVER\A2500v3 BUSTYPE=PCI1). Otherwise the driver may not find the card. If you don't know which bus you have, try loading without the option. If it loads, you don't need it.

Add the load and bind statements you require to the server's AUTOEXEC.NCF file so that the LAN driver will load automatically each time the server starts up. Here's an example of how the commands would look in your AUTOEXEC.NCF file.

("NCF Files Options - Create / Edit Server Star tup Files") LOAD A2500v3 FRAME=Ethernet_802.3 (overrides default frame type) BIND IPX to A2500v3 net=1 (all servers on the LAN segment need the same #)

2. Proceed with the installation as outlined by Novell.

Page 58

Novell Netware

Multiple Adapters If you have multiple Allied Telesyn adapters installed in the system, use

the keyword SLOT to identify each card to the driver. If you have multiple adapters in a single server, each adapter must have a different network number and SLOT number. Also, you might want to name each adapter. So add the options in LOAD commands to distinguish particular cards. For example:

LOAD A2500v3 FRAME=Ethernet_802.2 NAME=LAN_A SLOT=1 BIND IPX TO LAN_A NET=11 LOAD A2500v3 FRAME=Ethernet_802.2 NAME=LAN_B SLOT=2 BIND IPX TO LAN_B NET=22

Add the load and bind statements you need to the server's AUTOEXEC.NCF file so that the adapter drivers load automatically each time the server starts.

SET MAXIMUM INTERRUPT EVENTS = 100000

The default setting is 10. If you have problems loading the driver on multiple adapters and the

initialization fails due to "Insufficient RCBs," increase the number of buffers allocated to the server. Add the following to STARTUP.NCF:

SET MINIMUM PACKET RECEIVE BUFFERS = 100 (or larger) SET MAXIMUM PACKET RECEIVE BUFFERS = 500 (or larger)

The minimum value you specify must be at least 30 times the number of PCI adapters in the computer.

Recommended settings: 1-3 adapters: 100 4 adapters: 150 The maximum you can specify depends on the amount of memory in

the server, but it must be greater than the minimum.

Page 59

Network Adapter Card Installation Guide - Book II

Removing an

Adapter Driver

from Novell

Netware 5/6

Server

This section contains the procedure for removing a network adapter driver from a system running Novell Netware 5 or Netware 6 Server.

To remove a driver, you can either use the NWCONFIG program supplied with NetWare or edit the AUTOEXEC.NCF in the SYS:SYSTEM directory with a text editor. The procedure below explains how to remove a driver using the NWCONFIG program.

1. Type NWCONFIG at the server console to bring up the installation module.

2. Select Driver Options and press Return.

3. Select Deselect a selected driver from the next menu and press Return. This moves the highlight to the installed adapter(s).

4. Selct the adapter you wish to remove.

5. Press Return again to remove the selected driver.

Page 60

Page 61

Chapter 6

Linux

This chapter contains the following procedures:

❑ Installing the ATNIC Driver for AT-2450/AT-2451, AT-2700/

AT-2701 Series, and AT-2745/AT -2 746 Ser ies PCI Ethernet Adapters on page 62

❑ Installing a Linux Driver for an AT-2915 and AT-2930 Series

Network Adapter on page 64

❑ Installing Linux on a AT-2970 or AT-2971 Series Adapters on page

Page 62

Linux

Installing the ATNIC Driver for AT-2450/AT-2451, AT-2700/ AT-2701 Series, and AT-2745/AT-2746 Series PCI Ethernet Adapters

This driver supports dynamic loading and unloading via the KLM support provided by Linux. As a result, you must custom build the driver for the particular version of the kernel installed. The driver is located on CardAssistant at /drivers/at2701/linux.

Limitations The current version of the driver has been tested as a loadable module

on Red Hat 7.0, 7.1, and 7.2 Linux distributions for i386 and ia64. Testing has also been done on other similar Linux distributions using the 2.4.x kernels.

Building the

Driver

Note

You must have the kernel source code and the the full GCC library installed in order to build and load the driver. For RedHat, the kernel source is located on the installation CDs (Disk2), not the source CDs. Look for a file with the name KERNEL-SOURCE-X.X.XX-i386.RPM, where x stands for build number.

To insure that the kernel source code is installed, change to the USR/SRC directory and verify that the linux source tree is present. Look for linux-x.x.x-x, where x stands for the current build numbers. If you only see a linux directory, chances are you've got the wrong source files installed.

1. Copy the Allied Telesyn driver source TAR file to a temporary directory, and type tar -xvf <filename> to extract the files.

2. Edit Makefile using VI or your favorite text editor, and change the LINUX path variable to the directory name where the kernel source files are installed.

3. Type make to compile the driver source code. You should see the atnic32.o file is created if successfull.

4. Continue with driver installation.

Installing the

Driver

Run make instal l to install the driver. The atnic32.o file will be copied to the

lib/modules/<build#>/kernel/drivers/net directory and depmod - a will be run to update dependancies.

Dynamic Loading Type insmod atnic32.o to dynamically load the driver without installing

it into the operating system. To configure network protocol and address, refer to Linux

documentations.

Page 63

Network Adapter Card Installation Guide - Book II

Changing

Configuration

Settings

To enable Autonegotiation edit the /etc/conf.modules file to add the line options atnic options=0 below the alias eth0 atnic line. The following indicate the various options for enabling the various interfaces. Only ONE of the following lines can be added. Only one interface is activated based on the keyword it represents. If neither option is selected the driver/device defaults to autonegotiation. Each option is selected by the number it represents.

Note

Full duplex ooperation on the Am79C970 chipset-based cards is only supported on the 10Base-T interface.

AT-2450F, AT-2450FTX, AT-2700TX, AT-2700FX, AT-2745FX, AT-2700FTX (AMD Am79C972 - Fast+ chipset):

options atnic options=0 #(MII, Autonegotiation) options atnic options=1 #(MII, 100Mbps, Half duplex) options atnic options=2 #(MII, 100Mbps, Full duplex) options atnic options=3 #(MII, 10Mbps, Half duplex) options atnic options=4 #(MII, 10Mbps, Full duplex)

AT-2450T/BT/AT/FT (AMD Am79C970 chipset):

options atnic options=5#(Auto Port Selection) options atnic options=6#(Fiber/BNC/AUI) options atnic options=7#(10baseT, Half duplex) options atnic options=8#(10baseT, Full duplex)2450FT/T/BT/AT For example: alias eth0 atnic

options atnic options=3

Page 64

Linux

Installing a Linux Driver for an AT-2915 and AT-2930 Series Network Adapter

Limitations The current version of the driver has been tested as a loadable module

on Red Hat 7.0, 7.1, and 7.2 Linux distributions for i386 and ia64. Testing has also been done on other similar Linux distributions using the 2.4.x kernels.

Building the

Driver

Note

1. Copy the Allied Telesyn driver source TAR file to a temporary directory, and type tar -xvf <filename> to extract the files.

2. Edit Makefile using VI or your favorite text editor, and change the LINUX path variable to the directory name where the kernel source files are installed.

3. Type make to compile the driver source code. You should see the at29xx.o file is created if successfull.

4. Continue with driver installation.

Installing the

Driver

Run make instal l to install the driver. The at29xx.o file will be copied to the

lib/modules/<build#>/kernel/drivers/net directory and depmod - a will be run to update dependancies.

Dynamic Loading Type insmod at29xx.o to dynamically load the driver without installing

it into the operating system. To configure network protocol and address, refer to Linux

documentations.

Page 65

Network Adapter Card Installation Guide - Book II

Module

Parameters

Optional parameters for the driver can be supplied as command line arguments to the insmod command. Typically, these parameters are set in the file /etc/modules.conf (see the man page for modules.conf). These parameters take the form:

<parameter>=value[,value,...]

where the multiple values for the same parameter are for multiple NICs installed in the system.

Note

The default values will be used when invalid values are selected.

All the parameters are listed below.

❑ line_speed

Selects the line speed of the link. This parameter is used together with full_duplex to select the speed and duplexity of the link.

The valid values are: 0 Autonegotiate (default) 10 10 Mbps 100 100 Mbps 1000 1000 Mbps

Note

The 1000 Mbps must be negotiated for copper twisted pair links.

❑ full_duplex

Selects the duplexity of the link. This paramter is used together with line_speed to select the speed and duplexity of the link. Note that this parameter is ignored if line_speed is 0.

The valid values are: 0half duplex 1 full duplex (default)

Page 66

Linux

❑ rx_flow_control

Enables or disables receiving flow control (pause) frames. This parameter is used together with auto_flow_control. The valid values are:

0 pause receive disabled (default) 1 pause receive enabled if auto_flow_control

is set to 0, or pause receive advertised if auto_flow_control is set to 1

❑ tx_flow_control

Enables or disables transmitting flow control (pause) frames. This parameter is used together with auto_flow_control.

The valid values are: 0 pause transmit disabled (default) 1 pause transmit enabled if auto_flow_control

is set to 0, or pause transmit advertised if auto_flow_control is set to 1

❑ auto_flow_control

Enables or disables autonegotiation of flow control. This parameter is used together with rx_flow_control and tx_flow_control to determine the advertised flow control capability.

The valid values are: 0 flow control autonegotiation disabled

(default)

1 flow control autonegotiation enabled with

capability specified in rx_flow_control and tx_flow_control (only valid if line_speed is set to 0)

Page 67

Network Adapter Card Installation Guide - Book II

Installing Linux on a AT-2970 or AT-2971 Series Adapters

Readme File for AT-2970 and AT-2971 v6.06 Allied Telesyn AT-2970 and AT-2971 Gigabit Ethernet Adapter family driver for LINUX Install Instructions for sk98lin Driver

Overview The sk98lin driver installation script supports the AT-2970 and AT-2971

Series Adapaters on Linux 2.4.11 and above. It has been tested with Linux on Intel/x86 machines.

Required Files To install the Linux driver for the AT-2970 or AT-2971 Series Adapters,

you will need the following files:

❑ The linux kernel source. ❑ Compiler tools

Installation

Guidelines

This script will automatically compile and load the sk98lin driver on your host system. Before performing both compilation and loading, you must shutdown any device using the sk98lin kernel module and to unload the old sk98lin kernel module. This script will do this automatically per default. If you want to shutdown and unload the old sk98lin kernel module manually, run the script in the EXPERT mode.

Plug a card into your computer. Without a card you are able to check the full driver functionality.

Be sure to use the same kernel source and kernel version. For instance, it might be, that you run kernel version 2.4.20, but the header files the kernel module will be compiled with refer to kernel version 2.4.21. If you do not have the same kernel version, install the sources and compile a new kernel. You cannot mix different kernel versions.

Installing the

Driver

To install the newest Linux driver, perform the following procedure:

1. Login as root.

2. Unpack the driver installation package using the command:

# tar xfvj install-606.tar.bz2

# bunzip2 -c install-606.tar.bz2 | tar xfv -

3. To start the driver build process, go to the DriverInstall directory and start the build process with the following command:

# cd DriverInstall # ./install.sh

Page 68

Linux

4. Choose your favorite installation method.

5. The driver will be compiled and installed

Loading the

Module Manually

To load the module manually, perform the following procedure:

1. Enter modprobe sk98lin.

2. If an AT-2971 adapter is installed in your computer and you have a /proc file system, execute the command:

# ls /proc/net/sk98lin/

This should produce an output containing a line with the following format:

eth0 eth1 ...

which indicates that your adapter has been found and initialized.

Unloading the

Module

To stop and unload the driver modules, perform the following procedure:

1. Execute the command ifconfig YOUR_DEVICE down.

# ifconfif eth0 down # ifconfif eth1 down

2. Execute the command rmmod sk98lin.

Driver Parameters Parameters can be set at the command line after the module has been

loaded with the command modprobe. In some distributions, the configuration tools are able to pass parameters to the driver module.

If you use the kernel module loader, you can set driver parameters in the file /etc/modules.conf (or old name: /etc/conf.modules).

Page 69

Chapter 7

BootROM

This chapter contains the procedures for installing and configuring an optional BootROM on an AT-2450, AT-2700, and AT-2745 Series Allied Telesyn Network Adapter Card.

Managed Boot

Agent

Managed Boot Agent (MBA) is client-based firmware that allows a client PC to do a "network bootî using the NIC. MBA is fully compliant with the Intel Wired for Management - Preboot Execution Environment (PXE) specification. PXE is the defacto industry standard protocols/APIs for network booting, enabling client PCs to access and boot from boot image files on a server. MBA streamlines networked desktop management, improves network security and cuts client administration costs. Network managers can remotely manage their networks, eliminating costly visits to the desktops

MBA adds extra important features in addition to standard PXE boot agents. To configure these features type ìCRTL ALT Bî when prompted to initialize the MBA configuration screen.

❑ MBA supports additional boot protocols:

— Remote Program Load (RPL) — Netware NCP/IPX — Traditional BootP and DHCP

Page 70

BootROM

❑ MBA has extra features and options, e.g.:

— The ability to configure speed and duplex without DOS

configuration tools.

— Prompt when network boot fails: PXE ñ waits a definable time

period before going to next device MBA ñ waits a definable time period before going to next device OR can display message to user and wait for a key press before going to next device

❑ MBA is compatible, robust, and dependable:

— MBA undergoes extensive and thorough testing:

The AT-2451, AT-2701, AT-2746 Series of adapters incorporates Managed Boot Agent (MBA) on the network interface card. MBA is available for the AT-2500, AT-2450, AT-2700, AT-2745 MBA series of adapters as an add-on option.

Page 71

Network Adapter Card Installation Guide - Book II

Installing a BootROM

Note

There are two different variations of AT-2450FTX, AT-2700FTX and AT-2745FX Series cards. One with a BootROM switch and one without. If using the version with a switch see Step 3. Also, if using an AT-2700TX or FX, only complete Step 1.

Installation Installing the MBA ROM is a straightforward task, but you must take care

to ensure that components are not damaged. Be sure you understand the following instructions before installing MBA.

Caution

Risk of equipment damage: Before removing an adapter card, attach an earth ground to the PC chassis. If an earth ground is unavailable, ensure that the power is switched off and plug in the PC's grounded AC power cord.

Caution

Wear an anti-static wrist strap when handling ROMs. As an additional measure, do not touch the ROM's connectors. Leave the ROM in its anti-static packaging when not in use.

If you are installing MBA on an adapter card that is already in your PC, remove the adapter card from the PC. If you are not familiar with inserting and removing adapter cards in your PC, refer to the Network Adapter Cards Installation Guide - Book I for instructions then locate the Boot ROM socket on your adapter card. You may need to refer to the installation guide to locate the correct ROM socket.

MBA Boot ROM Configuration

To configure the MBA Boot ROM options press Ctrl + Alt+ B during PXE initialization to enter the MBA Configuration Menu. This message will appear during the Boot ROM initialization. In this menu you can select the boot method and other parameters. Two new features are the Speed/Duplex and Boot ROM Port parameters. The Speed/Duplex parameter allows the user to determine the default speed and duplex configuration without the DOS configuration utility. The Boot ROM Port parameter allows the user to configure the default port on dual-port adapters. Allied Telesyn’s dual-port adapter cards are: AT-2450FTX, AT-2700FTX, and AT-2745FX

Page 72

BootROM

PLCC Socket Installation

The PLCC socket has three square corners and one angled corner. The angled corner of the ROM must be oriented to match the angled corner of the socket.

Remove the MBA ROM from its anti-static packaging, and align the angled corner of the MBA ROM with the angled corner of the ROM socket on the adapter card. Press down gently and evenly on the ROM to ensure that it is seated correctly in the socket. Figure 11 shows the MBA ROM installation for the AT-BP2700 and AT-BP2501 PC Boot Agent.

Figure 11 MBA ROM Installation

Figure 12 shows an MBA ROM installation for the AT-BD2700 and AT-BD2500 PC Boot Agent.

Figure 12 MBA ROM Installed on a AT-BD2700/AT-BD2500

Installing the NIC into the PC and Enabling the ROM Socket

Now that the ROM has been inserted into the adapter card, you can install the card into your PC.

To install the adapter card into the PC, refer to the Network Adapter Cards Installation Guide, Book II for instructions. The AT-2450 and AT-2700 Series Adapter Cards will recognize the inserted MBA Boot ROM automatically. However, PXE can be disabled or enabled through the diagnostics program diag.exe.

Page 73

Network Adapter Card Installation Guide - Book II

The AT-2500 and AT-2501 adapter cards will require the card to be configured for Boot ROM support, it is disabled by default. To enable Boot ROM support, start the AT-2500 or AT-2501 DOS diagnostics program, setup25 and enable the Boot ROM from the configuration menu.

BootROM

Parameter

1. Run the diagnostics program that came with your Allied Telesyn adapter. (diag.exe, diag25.exe, etc.).

2. If using an AT-2450 and AT-2700 series Combo card, set the BootROM Parameter to the desired port (copper or fiber). If using an AT-2500 series adapter set the BootROM parameter to enable.

For the AT-2450FTX, AT-2700FTX, and AT-2745FX versions with switches you must set your switch to the proper position based on which port you are using (Copper or Fiber).

Note

For proper operation when BootROM is NOT installed insure the Diagnostics parameter BootRom and switch are set to Factory Default.

Table 1 AT-2450FTX

Diag Setting Switch Position

Copper

1. Factory default.

Fiber Down

Table 2 AT-2700FTX

Diag Setting Switch Position

Fiber

1. Factory default.

Down

Copper Up

Table 3 AT-2745FX

Diag Setting Switch Position

100 Mb

1. Factory default.

10 Mb Down

Page 74

Page 75

Appendix A

Translated Safety and Emission Information

Important: This appendix contains multiple-lang u age translations for the safety statements in this guide.

Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthalten en Sicherheitshi n we is e in mehreren Sprachen.

Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog.

Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de veiligheidso pmerkingen in deze gids.

Important: Cette annexe contient la traduction en plusieurs langues des instructions de sécurité figurant dans ce guide.

Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla kielellä. Importante: questa appendice contiene traduzioni in più lingue degli avvisi di

sicurezza di questa guida. Viktig: Dette tillegget inneholder oversettelser til flere språk av

sikkerhetsinformasjonen i denne veiledningen. Importante: Este anexo contém traduções em vários idi oma s das advertênc ias de

segurança neste guia. Importante: Este apéndice contiene traducciones en múltiples idiomas d e l os

mensajes de seguridad incluidos en esta guía. Obs! Denna bilaga innehåller flerspråkiga översättningar av säkerhetsmeddelandena i

denna handledning.

Page 76

Translated Safety and Emission Information

Standards: This product meets the following standards.

European Community (EC) Electromagnetic Compat ibility Directive

This equipment has been tested and found to comply with the protection requirements of European Emission Standards EN55022 Class B/EN61000-3-2 and the ITE European Immunity Standard EN55024

" 1 RFI Emission EN55022 Class B, EN61000-3-2, EN61000-3-3 " 2 Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take

adequate measures.

" 3 Immunity EN55024

Safety

" 4 Electrical Safety TUV-EN60950, UL1950, CSA 950, EN60825 " 5Laser EN60825 " 6This is a “CLASS 1 LED PRODUCT” " 7 Warning Do not stare into the Laser beam. " 8 Lightning Danger

Danger: Do not work on equipment or cables during periods of lightning activity.

" 9 Operating Temperature: This product is designed for a maximum ambient temperature of 50 degrees C. " 10 All Countries: Install product in accordance with local and National Electrical Codes.

U.S. Federal Communications Commission

Radiated Energy

Note: Modifications or changes not expressly approved by the manufacturer or the FCC can void your right to operate this equipment.

Industry Canada

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Page 77

Network Adapter Installation Guide - Book II

Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Sicherheitsnormen.

" 1 Hochfrequenzstörung EN55022 Klasse B " 2 Warnung: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender

angemessene Gegenmaßnahmen ergreifen.

" 3 Störsicherheit EN55024

Sicherheit

" 4 Elektrische Sicherheit TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Das ist ein “LED Produkt der Klasse 1” " 7 Warnung: Nicht direkt in den Strahl blicken. " 8 Gefahr Durch Blitzschlag

Gefahr: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters ausführen.

" 9 Betriebstemperatur: Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als 50° C entworfen. " 10 Alle Länder: Installation muß örtlichen und nationalen elektrischen Vorschriften entsprechen.

Standarder: Dette produkt opfylder følgende sikkerhedsstandarder.

" 1 Radiofrekvens forstyrrelsesem is sion EN55022 Klasse B " 2 Advarsel: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at

tage tilstrækkelige foranstaltninger.

" 3Immunitet EN55024

Sikkerhed

" 4 Elektrisk sikkerhed TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Dette er et “PRODUKT UNDER KLASSE 1 LED” " 7 Advarsel: Stirr ikke på strålen. " 8 Fare Under Uvejr

Fare: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.

" 9 Betjeningstemperatur: Dette apparat er konstrueret til en omgivende temperatur på maksimum 50grader C. " 10 Alle lande: Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer.

Normen: Dit product voldoet aan de volgende veiligheidsnormen.

" 1 RFI Emissie EN55022 Klasse B " 2 Waarschuwing: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om

gepaste maatregelen te nemen.

" 3 Immuniteit EN55024

Veiligheid

" 4 Electrische Veiligheid TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Dit is een “KLASSE 1 LED-PRODUKT” " 7 Waarchuwing: Neit in de straal staren. " 8 Gevaar Voor Blikseminslag

Gevaar: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.

" 9 Bedrijfstemperatuur: De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 50 graden Celsius. " 10 Alle landen: het toestel installeren overeenkomstig de lokale en nationale elektrische voorschriften.

Page 78

Translated Safety and Emission Information

Normes: ce produit est conforme aux normes de sécurité suivantes :

" 1 Emission d’interférences radioélectriques EN55022 Classe B " 2 Mise En Garde: dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas,

l’utilisateur devra prendre les mesures adéquates.

" 3 Immunité EN55024

Sécurité

" 4 Sécurité électrique TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Ce matériel est un “PRODUIT À DIODE ÉLECTROLUMINESCENTE DE CLASSE 1” " 7 Attention: Ne pas fixer le faisceau des yeux. " 8 Danger De Foudre

Danger: Ne pas manier le matériel ou les CÂBLES lors d’activité orageuse.

" 9 Température De Fonctionnement: Ce matériel est capable de tolérer une température ambiante maximum de 50 degrés Celsius. " 10 Pour Tous Pa y s : Installer le matériel conformément aux normes électriques nationales et locales.

Normit: Tämä tuote on seuraavien turvallisuusnormien mukainen.

" 1 Radioaaltojen häirintä EN55022 Luokka B " 2 Varoitus: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapaukse ssa laitteen käyttäjän on mahdollisesti

ryhdyttävä tarpeellisiin toimenpiteisiin.

" 3Kestävyys EN55024

Turvallisuus

" 4 Sähköturvallisuus TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Tämä on “ENSIMMÄISEN LUOKAN VALODIODITUOTE” " 7 Variotus: Älä katso säteeseen. " 8 Salamaniskuvaara

Hengenvaara: Älä työskentele laitteiden tai kaapeleiden kanssa salamoinnin aikanA.

" 9 Käyttölämpötila: Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 50°C. " 10 Kaikki Maat: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten mukaisesti.

Standard: questo prodotto soddisfa i seguenti standard di sicurezza.

" 1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B " 2 Avvertenza: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi

all’utente di prendere gli adeguati provvedimenti.

" 3 Immunità EN55024

Norme Di Sicurezza

" 4 Sicurezza elettrica TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Questo è un “PRODOTTO CON LED DI CLASSE 1” " 7 Avertenza: Non fissare il raggio con gli occhi. " 8 Pericolo Di Fulmini

Pericolo: Non lavorare sul dispositivo o sui CAVI durante precipitazioni temporalesche .

" 9 Temperatura Di Funzionamento: Questo prodotto è concepito per una temperatura ambientale massima di 50 gradi centigradi. " 10 Tutti I Paesi: installare il prodotto in conformità delle vigenti normative elettriche nazionali.

Page 79

Network Adapter Installation Guide - Book II

Sikkerhetskrav: Dette produktet oppfyller følgende sikkerhetskrav:

" 1 RFI stråling EN55022 Klasse B " 2 Advarsel: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta

de nødvendige forholdsregler.

" 3Immunitet EN55024

Sikkerhet

" 4 Elektrisk sikkerhet TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Dette er et “KLASSE 1 LED PRODUKT” " 7 Advarsal: Stirr ikke på strålen. " 8 Fare For Lynnedslag

Fare: Arbeid ikke på utstyr eller kabler i tordenvær.

" 9 Driftstemperatur: Dette produktet er konstruert for bruk i maksimum romtemperatur på 50 grader celsius. " 10 Alle Land: Produktet må installeres i samsvar med de lokale og nasjonale elektriske koder.

Padrões: Este produto satisfaz os seguintes padrões de segurança:

" 1 Emissão de interferência de radiofrequência EN55022 Classe B " 2 Aviso: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que

o utente tome as medidas adequadas.

" 3Imunidade EN55024

Segurança

" 4 Segurança Eléctrica TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Este é um “PRODUTO CLASSE 1 LED” " 7 Aviso: Não olhe fixamente para o raio. " 8 Perigo De Choque Causado Por Raio

Perigo: Não trabalhe no equipamento ou nos cabos durante períodos suscetíveis a quedas de raio.

" 9 Temperatura De Funcionamento: Este produto foi projetado para uma temperatura ambiente máxima de 50 graus centígrados. " 10 Todos Os Países: Instale o produto de acordo com as normas nacionais e locais para instalações elétricas.

Normas: este producto cumple con las siguientes normas de seguridad.

" 1 Emisión RFI EN55022 Clase B " 2 Advertencia: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del

usuario que tome las medidas que sean convenientes al respecto.

" 3Inmunidad EN55024

Seguridad

" 4 Seguridad eléctrica TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Este es un “PRODUCTO DE DIODO LUMINISCENTE (LED) CLASE 1” " 7 ¡Advertencia! No mirat fijamente el haz. " 8 Peligro De Rayos

Peligro: No realice ningun tipo de trabajo o conexion en los equipos o en los cables durante tormentas electricas.

" 9 Temperatura Requerida Para La Operación: Este producto está diseñado para una temperatura ambiental máxima de 50 grados

" 10 Para Todos Los Países: Monte el producto de acuerdo con los Códigos Eléctricos locales y nacionales.

Page 80

Translated Safety and Emission Information

Normer: Denna produkt uppfyller följande säkerhetsnormer.

" 1 Radiostörning EN55022 Klass B " 2 Varning: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga

åtgärder.

" 3Immunitet EN55024

Säkerhet

" 4 Elsäkerhet TUV-EN60950, UL1950, CSA 950 " 5Laser EN60825 " 6 Detta är en “KLASS 1 LYSDIODPRODUKT” " 7 Varning! Laserstrålning när enheten är öppen. " 8 Fara För Blixtnedslag

Fara: Arbeta ej på utrustningen eller kablarna vid åskväder.

" 9 Driftstemperatur: Denna produkt är konstruerad för rumstemperatur ej överstigande 50 grader Celsius. " 10 Alla Länder: Installera produkten i enlighet med lokala och statliga bestämmelser för elektrisk utrustning.

Allied Telesis AT-2400, AT-2701, AT-2451, AT-2700, AT-2745 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual