AR450S SECURITY APPLIANCE
QUICK INSTALL GUIDE
Software Release 2.5.2
AR450S Quick Install Guide
Document Number C613-04045-01 REV A.
Copyright © 2003 Allied Telesyn International, Corp.
19800 North Creek Parkway, Suite 200, Bothell, WA 98011, USA.
All rights reserved. No part of this publication may be reproduced without prior written
permission from Allied Telesyn.
Allied Telesyn International, Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall Allied
Telesyn be liable for any incidental, special, indirect, or consequential damages
whatsoever, including but not limited to lost profits, arising out of or related to this
manual or the information contained herein, even if Allied Telesyn has been advised of,
known, or should have known, the possibility of such damages.
All trademarks are the property of their respective owners.
Quick Install Guide 3
Documentation Roadmap
AR450S Router
AR400 Series Safety and Statutory Information
AR450S Quick Install Guide
AR400 Series User Guide
AR400 Series Software Reference
AR Router Hardware Reference
Printed Acrobat PDF
Models Covered By This Guide
This Quick Install Guide includes information on the following model:
■ AR450S
Quick Install Guide updates can be found at
www.alliedtelesyn.co.nz/support/ar400/
General Customer Support
Visit www.alliedtelesyn.co.nz for
the latest documentation, FAQ,
and support information
Website
Package Contents
The following items are included with each AR450S router. Contact your sales
representative if any items are damaged or missing.
■ One AR450S router.
■ One AC power cord.
■ One power cord retaining clip.
■ One terminal cable for connecting the router to a terminal or PC.
■ Two UTP network cables.
■ One rack-mount kit with brackets and screws.
■ One AR450S Router Quick Install Guide.
■ One Safety and Statutory Information booklet.
■ One AR400 Series Router Documentation and Tools CD-ROM (which
includes the complete AR400 Series Document Set and utilities).
■ One warranty card.
C613-04045-01 REV A
4 AR450S Router
Selecting a Site
The router should be installed on a level surface such as a desktop or bench.
When installing the router, choose a site that:
■ Allows adequate airflow around the router and its vents.
■ Is free of dust and moisture.
■ Will maintain an ambient temperature range of 0 to 40º C (32 to 104º F) and
a humidity range of 5 to 95% non-condensing.
■ Has a reliable and earthed (grounded) power supply circuit, preferably
dedicated and filtered.
■ Does not expose cabling to sources of electrical noise, such as radios,
transmitters, broadband amplifiers, power lines, electric motors, and
fluorescent fixtures.
■ Allows easy access to the router’s power and cable connections.
Installing the Router
This equipment must be earthed.
Follow these steps to install the router:
1. Read the safety information.
For safety information, see the Safety and Statutory Information booklet. A
copy of this booklet is supplied with each router, and can also be found on
the Documentation and Tools CD-ROM or at
www.alliedtelesyn.co.nz/support/ar400/
2. Unpack the router.
Verify the package contents. If any items are damaged or missing, contact
your sales representative.
3. Place the router in its operating location.
See the previous Selecting a Site section for guidelines on choosing a
suitable location.
4. Check the supply voltage and the router’s rated voltage.
AR450S routers are fitted with a universal mains power supply that will
function over the range 100-240 VAC and 50–60Hz.
The specific power supply requirements for a particular model are clearly
displayed on the rear or underside of the router. If the supply is outside the
accepted range for the router, the router may not operate and damage to the
router may result.
C613-04045-01 REV A
Loading...