Alliance Laundry Systems T477C User Manual

Drying Tumblers

NOTA: Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com.

Stacked 30 Pound Capacity Stacked 45 Pound Capacity

Starting Serial No. 0602004144

Refer to Page 4 for Model Identification

H I G H T E M P

S T A

R T

L O W T E M

P M E D T E M P

2 5

S E L E

T T E M P

S E L

C T

S E

T C O

S T A

R T

L O W T E M

P M E

I N S E

T C O

S H S T A R

D T E M P

N O H E A T

Installation

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

T477C

Part No. 70304601R8

September 2008

Installation must conform with local codes or in the absence of local codes with:

In the U.S.A.

, installation must conform to the latest edition of the American National Standard Z223.1/

NFPA 54 “National Fuel Gas Code” and Standard ANSI/NFPA 70 “National Electric Code.”

In Canada

, installation must comply with Standards CAN/CSA-B149.1 or Natural Gas and Propane

Installation Code and CSA C22.1, latest edition, Canadian Electric Code, Part I.

In Australia

, installation must comply with the Australian Gas Association Installation Code for Gas

Burning Appliances and Equipment.

WARNING

FOR Y OUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS: – Do not try to light any appliance. – Do not touch any electrical switch; do

not use any phone in your building.

– Clear the room, building or area of all

occupants.

– Immediately call your gas sup plier from

a neighbor’s phone. Follow the gas supplier’s instructions.

– If you cannot reach your gas supplier,

call the fire department.

• Installation and service must be performed by a qualified inst aller , service agency or the gas supplier.

W033

W052

POUR VOTRE SÉCURITÉ, les informations de ce guide doivent être respectées afin de réduire les risques d’incendie, d’explosion ou d’éviter les dommages matériels, personnels ou blessures mortelles.

• Ne pas entreposer ou utiliser d’essence ou toutes autres vapeurs et liquides inflammables à proximité de cette machine ou de tout autre appareil.

• QUE FAIRE EN CAS D’ODEUR DE GAZ :

– Ne pas mettre d’appareil en marche. – Ne pas toucher aux interrupteurs

électriques ; ne pas utiliser le téléphone des lieux.

– Évacuer la pièce, le bâtiment ou la zone

de tous les occupants.

– Appeler immédiatement le fournisseur

de gaz de la maison d’un voisin. Respecter les instructions communiquées par le fournisseur.

– Si vous ne pouvez pas joindre le

fournisseur de gaz, appeler le service

MISE EN GARDE

d’incendie.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

W053

The following information applies to the state of Massachusetts, USA.

• This appliance can only be installed by a

Massachusetts licensed plumber or gas fitter.

• L’installation et l’entretien doivent être effectués par un installateur, service d’entretien qualifiés ou par le fournisseur de gaz.

POUR VOTRE SÉCURITÉ

Ne pas entreposer ou utiliser d’essence ou toutes autres vapeurs et liquides inflammables à proximité de cette unité ou de tout autre appareil.

• This appliance must be installed with a 36

inch (91 cm) long flexible gas connector.

• A "T-Handle" type gas shut-off valve must be

installed in the gas supply line to this appliance.

• This appliance must not be installed in a

bedroom or bathroom.

IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the user smells gas. These instructions must be posted in a prominent location. Step-by-step instructions of the above safety information must be posted in a prominent location near the tumbler for customer use.

W033R3QU

W052R5QU

W053R2QU

Table of

Contents

Introduction......................................................................................... 4

Model Identification ............................................................................. 4

Customer Service.................................................................................. 5

Wiring Diagram .................................................................................... 5

Serial Plate Location............................................................................. 5

Safety Information.............................................................................. 6

Explanation of Safety Messages........................................................... 6

Important Safety Instructions ............................................................... 7

Specifications and Dimensions........................................................... 9

Cabinet Dimensions.............................................................................. 10

Exhaust Outlet Locations...................................................................... 11

Gas Connection Locations.................................................................... 12

Electrical Connection Locations........................................................... 13

Steam Connection Locations ................................................................ 14

Installation........................................................................................... 15

Pre-Installation Inspection .................................................................... 15

Location Requirements......................................................................... 15

Position and Level the Tumbler............................................................ 17

Before Placing Tumbler into Service ................................................... 18

Required for CE Models Only ......................................................... 19

Installing CE Gas Drying Tumblers ..................................................... 19

General Information......................................................................... 19

Basic Configuration ......................................................................... 20

Specific Conversion Procedures ...................................................... 22

Exhaust Requirements ....................................................................... 24

Layout ................................................................................................... 24

Make-Up Air......................................................................................... 24

Venting ................................................................................................. 24

Individual Venting ........................................................................... 25

Manifold Venting............................................................................. 27

Gas Requirements............................................................................... 30

Gas Supply Pipe Sizing and Looping ................................................... 32

High Altitude Burner Orifice Sizing..................................................... 34

Electrical Requirements..................................................................... 35

Grounding Instructions ......................................................................... 35

For CE Models Only............................................................................. 35

Service/Ground Location...................................................................... 36

Connecting Electrical Service............................................................... 37

Configuring Your Tumbler for Other Service Voltages .................. 37

Electrical Connections ..................................................................... 37

Conversion Instructions........................................................................ 38

Electrical Requirements for Gas and Steam Models ............................ 40

Electrical Requirements for Electric Models........................................ 42

Steam Requirements........................................................................... 43

Piping Recommendations ..................................................................... 43

Installing Steam Trap and Making Condensate Return Connections... 44

means without the expressed written consent of the publisher.

70304601© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Single Drop Timer .............................................................................. 46

Power-Up Mode.................................................................................... 46

Ready Mode.......................................................................................... 46

Start Mode ............................................................................................ 46

Run Mode ............................................................................................. 46

Setting Dry Time Dipswitches.............................................................. 46

Dipswitch Settings................................................................................ 47

Adjustments......................................................................................... 49

Loading Door Switch............................................................................ 49

Airflow Switch...................................................................................... 49

Door Strike............................................................................................ 50

Removing Tumbler from Service...................................................... 51

70304601

Introduction

Model Identification

Information in this manual is applicable to these models:

Gas Steam Electric

IPD30STG2-ITT30L IPD30STG2-ITT30N MTT30N NTT30N SAT30L SAT30N STT30D STT30L STT30N SUT30L SUT30N UAT30L UAT30N UTT30L UTT30N UUT30L UUT30N

MTT45N NTT45N STT45D STT45L STT45N SUT45L SUT45N UTT45L UTT45N

T30

T45

CHD30STG2-CAT30L CHD30STG2-CAT30N CHD30STG2-CTT30L CHD30STG2-CTT30N CHD30STG2-CUT30L CHD30STG2-CUT30N DRST30G2-BAT30L DRST30G2-BAT30N DRST30G2-BTT30D DRST30G2-BTT30L DRST30G2-BTT30N DRST30G2-BUT30L DRST30G2-BUT30N HAT30L HAT30N HTT30D HTT30L HTT30N HUT30L HUT30N

CTT45L CTT45N DRST45G2-BTT45D DRST45G2-BTT45L DRST45G2-BTT45N HTT45D HTT45L HTT45N HUT45L HUT45N IPD45STG2-ITT45L IPD45STG2-ITT45N

CHD30STS2-CTT30S CHD30STS2-CUT30S DRST30S2-BTT30S DRST30S2-BUT30S HTT30S HUT30S IPD30STS2-ITT30S STT30S SUT30S UTT30S UUT30S

Not Applicable Not Applicable

CHD30STE2-CTT30E CHD30STE2-CUT30E DRST30E2-BTT30E DRST30E2-BUT30E HTT30E HUT30E IPD30STE2-ITT30E STT30E SUT30E UTT30E UUT30E

Includes models with control suffixes:

3O– DX4 OPL NC– NetMaster coin SX– single drop, prep for coin

3V– DX4 vended NR– NetMaster card ZC– NetMaster network coin

3X– DX4 prep for coin NX– NetMaster, prep for coin ZR– NetMaster network card

BC– basic electronic, coin NY– NetMaster, prep for card ZX– NetMaster network, prep for coin

BL– basic electronic, central pay OM– OPL micro ZY– NetMaster network, prep for card

BX– basic electronic, prep for coin QT– dual digital timer

BY– basic electronic, prep for card SD– single drop

Introduction

Customer Service

If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor.

For technical assistance, call (920) 748-3121.

Wiring Diagram

The wiring diagram is located in the upper junction or upper contactor box.

The wiring diagram part number is located in the lower portion of the electrical data on the serial plate.

Serial Plate Location

When calling or writing for information about your product, be sure to mention model and serial numbers. Model and serial numbers are found on serial plate on the rear of machine and inside door.

1 Serial Plate

Conversion Table

Multiply By To Obtain Multiply By To Obtain

Btu 0.252 kCal Pounds/sq. inch 0.06895 Bars

Btu 1055 Joules Pounds/sq. inch 0.070 kg/sq. cm

Inch 25.4 Millimeters Pounds (lbs.) 0.454 Kilograms

Inches W.C. 0.036 Pounds/sq. inch Boiler Horsepower 33,479 Btu/hr.

Inches W.C. 0.249 kPa Boiler Horsepower 34.5 lbs. steam/hr.

lb/inch

70304601

(psi) 6.895 kPa CFM 0.471 liters/second

28.32 Liters kW 3414 Btu/hr.

TMB1974N

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

WARNING

Failure to install, maintain, and/or operate this machine according to manufacturer’s instructions may result in conditions which can produce serious injury, death and/or property damage.

W051R1

DANGER

Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

WARNING

Indicates a hazardous situation that, if not avoided, could cause severe personal injury or death.

CAUTION

Indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property damage.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness are factors which CANNOT be built into this tumbler. These factors MUST BE supplied by the person(s) installing, maintaining or operating the tumbler.

Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do not understand.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

Safety Information

Important Safety Instructions

Save These Instructions

WARNING

Hazardous Voltage. Can cause shock, burn or cause death. Allow machine power to remain off for two minutes prior to w orking in and around AC inverter drive.

1. Read all instructions before using the tumbler.

2. Refer to the GROUNDING INSTRUCTIONS

for the proper grounding of the tumbler.

3. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.

4. Do not allow children on or in the tumbler. This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.

W359

14. The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified service personnel.

15. If not installed, operated and maintained in accordance with the manufacturer’s instructions or if there is damage to or mishandling of this product’s components, use of this product could expose you to substances in the fuel or from fuel combustion which can cause death or serious illness and which are known to the State of California to cause cancer, birth defects or other reproductive harm.

16. Tumbler will not operate with the loading door open. DO NOT bypass the door safety switch to permit the tumbler to operate with the door open. The tumbler will stop tumbling when the door is opened. Do not use the tumbler if it does not stop tumbling when the door is opened or starts tumbling without pressing or turning the START mechanism. Remove the tumbler from use and call for service.

17. Tumbler will not operate with lint panel open. DO NOT bypass lint panel safety switch to permit the tumbler to operate with the lint panel open.

5. Before the tumbler is removed from service or discarded, remove the door to the drying compartment and the door to the lint compartment.

6. Do not reach into the tumbler if the cylinder is revolving.

7. Do not install or store the tumbler where it will be exposed to water and/or weather.

8. Do not tamper with the controls.

9. Do not repair or replace any part of the tumbler, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

10. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

11. To reduce the risk of fire, DO NOT DRY plastics or articles containing foam rubber or similarly textured rubberlike materials.

18. Do not put articles soiled with vegetable or cooking oil in the tumbler, as these oils may not be removed during washing. Due to the remaining oil, the fabric may catch on fire by itself.

19. To reduce the risk of fire, DO NOT put clothes which have traces of any flammable substances such as machine oil, flammable chemicals, thinner, etc. or anything containing wax or chemicals such as in mops and cleaning cloths, or anything dry-cleaned at home with dry-cleaning solvent in the tumbler.

20. Use the tumbler only for its intended purpose, drying fabrics.

21. ALWAYS disconnect and lockout the electrical power to the tumbler before servicing. Disconnect power by shutting off appropriate breaker or fuse.

22. Install this tumbler according to the INSTALLATION INSTRUCTIONS. All connections for electrical power, grounding, and gas supply must comply with local codes and be made by licensed personnel when required.

12. Always clean the lint filter daily.

13. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and dirt.

70304601

Safety Information

23. Remove laundry immediately after tumbler stops.

24. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of reach of children at all times (preferably in a locked cabinet).

25. Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder with a damp cloth to remove particles of fiberglass.

26. Always follow the fabric care instructions supplied by the garment manufacturer.

27. Never operate the tumbler with any guards and/or panels removed.

28. DO NOT operate the tumbler if it is smoking, grinding, has missing or broken parts.

29. DO NOT bypass any safety devices.

30. Solvent vapors from dry-cleaning machines create acids when drawn through the heater of the drying unit. These acids are corrosive to the tumbler as well as to the laundry load being dried. Be sure make-up air is free of solvent vapors.

31. Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

WARNING

T o reduce the risk of serious injury, install lockable door(s) to prevent public access to rear of tumblers.

W055

70304601

Specifications and Dimensions

Specifications T30 T45

Noise level measured during operation at operator position of 3.3 feet (1 meter) in front of machine and

5.2 feet (1.6 meters) from floor. Net Weight (approximate):

Pounds (kg) Cylinder Size:

Inches (mm) Cylinder Capacity (dry weight)

Pounds (kg) Drive Motor Horsepower** Fan Motor Horsepow er**

50 Hertz 340

Maximum Airflow per Pocket**: C.F.M. (l/sec)

Maximum Static Back Pressure*: Inches W.C. (mbar)

60 Hertz 400

50 Hertz 0.8

60 Hertz 0.9

66 dBA 67 dBA

544

(247)

30 x 26

(762 x 660)

2 x 30

(2 x 13.6)

1/4 1/2

(160)

(189)

(2.0)

(2.3)

(305)

33 x 30

(838 x 762)

2 x 45

(2 x 20.5)

N/A

(283)

N/A

(2.3)

673

600

0.9

Gas Connection Gas Burner Rating**:

Btu/hr (kW, Mj/hr)

Heating Element Rating**:

Steam Connection Steam Coil Rating at 100 psig**:

Boiler Horsepower (Btu/hr) Steam Coil Rating at 15 psig**:

Boiler Horsepower (Btu/hr)

* with both pockets running

** for each pocket

N/A = Not Applicable

Gas Models

Electric Models

Steam Models

1/2 in. NPT 1/2 in. NPT

73,000

(21.4, 77)

21 kW N/A

3/4 in. NPT N/A

3.2

(111,000)

2.2

(74,000)

95,000

(27.8, 100.2)

N/A

70304601

Specifications and Dimensions

Cabinet Dimensions

G I

TMB2230N

ModelsABCDE

T30

28 in.

(711 mm)

48 in.

(1219 mm)

44 in.

(1118 mm)

11 in.

(279 mm)

10 in.

(254 mm)

T45

31.88 in.

(810 mm)

49 in.

(1245 mm)

N/A N/A

Models F G H I J

T30

T45

N/A = Not Applicable

25.02 in.

(636 mm)

29.37 in.

(746 mm)

42.76 in.

(1086 mm)

48.62 in.

(1235 mm)

27.38 in.

(695 mm)

30.50 in.

(775 mm)

31.5 in.

(800 mm)

34.5 in.

(876 mm)

NOTE: To meet ADA compliance, install a 4 inch (102 mm) riser on T30 models only.

9 in.

(229 mm)

76.25 in.

(1937 mm)

81.25 in.

(2063.75 mm)

70304601

Exhaust Outlet Locations

Specifications and Dimensions

Models

T30

T45

TMB1969N

Rear Exhaust

Diameter A B C

Elliptical

Fits 8 in. (203 mm)

Elliptical

Fits 10 in. (254 mm)

36.54 in.

(928 mm)

40.88 in.

(1038 mm)

4.25 in.

(108 mm)

4.75 in.

(121 mm)

TMB1969N

62.42 in.

(1585 mm)

66.00 in.

(1676 mm)

70304601

Specifications and Dimensions

Gas Connection Locations

1 1/2 in. NPT

TMB1970N

T30

Models

Non-CE and

Non-Australian

CE and

Australian

T45

Gas Connection

ABC

75.20 in.

(1910 mm)

75.28 in.

(1912 mm)

78.75 in.

(2000 mm)

1.74 in.

(44 mm)

2.5 in.

(64 mm)

4.12 in.

(105 mm)

36.84 in.

(936 mm)

30.60 in.

(777 mm)

42.88 in.

(1089 mm)

70304601

Electrical Connection Locations

Specifications and Dimensions

GAS AND STEAM ELECTRIC

Electric Service

TMB1971N

Models

T30

T45

N/A = Not Applicable

Gas and Steam Models Electric Models

ABCDE

59 in.

(1498 mm)

62.5 in.

(1588 mm)

1.75 in.

(44 mm)

1.75 in.

(44 mm)

35.63 in.

(905 mm)

73.21 in.

(1859 mm)

N/A N/A N/A

2.28 in.

(58 mm)

70304601

Specifications and Dimensions

Steam Connection Locations

Inlet Outlet

Models

ACBD

T30

(Upper)

T30

(Lower)

73.93 in.

(1877 mm)

36.35 in.

(923 mm)

NOTE: All connections use 3/4 inch NPT pipe.

6.29 in.

(160 mm)

6.29 in.

(160 mm)

62.71 in.

(1592 mm)

25.13 in.

(638 mm)

TMB1972N

2.39 in.

(61 mm)

2.39 in.

(61 mm)

70304601

+ 37 hidden pages