Alliance Laundry Systems SX30BVPA7, NX30BVPA7, SX30BVQA7, NX30BVXA7, NX30BVXM7 User Manual

Download

Page 1

Washer-Extractors

Cabinet Freestanding

Coin Models

Installation/Operation Supplement

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

Part No. 9002062R2

July 2008

Page 2

Page 3

Installation/Operation/Supplement

Table of

Contents

Introduction......................................................................................... 2

Model Identification ............................................................................. 2

Safety Information.............................................................................. 3

Explanation of Safety Messages........................................................... 3

Important Safety Instructions ............................................................... 3

Safety Decals ........................................................................................ 5

Operator Safety..................................................................................... 6

Specifications and Dimensions........................................................... 7

Installation........................................................................................... 11

Dimensional Clearances................................................................... 11

Machine Foundation ........................................................................ 11

Mounting Bolt Installation (If Required).............................................. 12

Removing the Transport Block............................................................. 13

Operation............................................................................................. 15

Control Panel ........................................................................................ 15

Operating Instructions .......................................................................... 16

Disposal of Unit................................................................................... 18

means without the expressed written consent of the publisher.

9002062

Page 4

Installation/Operation Supplement

Introduction

Model Identification

Information in this manual is applicable to these models:

NX18BVPA6 NX18BVXM7 NX30BVXA7 SX30BVPA7

NX18BVPA7 NX30BVPA6 NX30BVXM7 SX30BVQA7

NX18BVQA6 NX30BVPA7 SX18BVPA7 SX30BVXA7

NX18BVQA7 NX30BVQA6 SX18BVQA7 SX30BVXM7

NX18BVXA6 NX30BVQA7 SX18BVXA7

NX18BVXA7 NX30BVXA6 SX18BVXM7

9002062

Page 5

Installation/Operation Supplement

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

DANGER

DANGER indicates the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the danger is ignored.

WARNING

WARNING indicates the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

Important Safety Instructions

WARNING

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

1. Read all instructions before using the washer.

2. Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION manual for the proper grounding of the washer.

3. Do not wash textiles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

CAUTION

CAUTION indicates the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

5. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable, do not smoke or use an open flame during this time.

6. Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This is a safety rule for all appliances.

7. Before the washer is removed from service or discarded, remove the door to the washing compartment.

8. Do not reach into the washer if the wash drum is moving.

9002062

Page 6

Installation/Operation Supplement

9. Do not install or store the washer where it will be exposed to water and/or weather.

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out.

12. To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electrical power source.

13. Use washer only for its intended purpose, washing textiles.

14. Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket.

15. ALWAYS disconnect the washer from electrical supply before attempting any service. Disconnect the power cord by grasping the plug, not the cord.

16. Install the washer according to the INSTALLATION INSTRUCTIONS. All connections for water, drain, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

17. To reduce the risk of fire, textiles which have traces of any flammable substances such as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or anything containing wax or chemicals such as in mops and cleaning cloths, must not be put into the washer. These flammable substances may cause the fabric to catch on fire by itself.

18. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

19. Keep washer in good condition. Bumping or dropping the washer can damage safety features. If this occurs, have washer checked by a qualified service person.

20. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

21. Be sure water connections have a shut-off valve and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day.

22. Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open.

23. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times (preferably in a locked cabinet).

24. Always follow the fabric care instructions supplied by the textile manufacturer.

25. Never operate the washer with any guards and/or panels removed.

26. DO NOT operate the washer with missing or broken parts.

27. DO NOT bypass any safety devices.

28. Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer.

Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer.

9002062

Page 7

Installation/Operation Supplement

WARNING

This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty.

SW004

IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

WARNING

Install the machine on a level floor of sufficient strength. Failure to do so may result in conditions which can produce serious injury, death and/or property damage.

W703

CAUTION

Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury.

SW025

WARNING

Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.

SW014

Safety Decals

Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician.

To provide personal safety and keep the machine in proper working order, follow all maintenance and safety procedures presented in this manual. If questions regarding safety arise, contact the manufacturer immediately.

Use manufacturer-authorized spare parts to avoid safety hazards.

9002062

Page 8

Installation/Operation Supplement

Operator Safety

WARNING

NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury.

SW012

To ensure the safety of machine operators, the following maintenance checks must be performed daily:

1. Prior to operating the machine, verify that all warning signs are present and legible. Missing or illegible signs must be replaced immediately. Make certain that spares are available.

2. Check door interlock before starting operation of the machine:

a. Attempt to start the machine with the door

open. The machine should not start with the door open.

b. Close the door without locking it and attempt

to start the machine. The machine should not start with the door unlocked.

Do not bypass any safety devices in the machine.

WARNING

Never operate the machine with a bypassed or disconnected balance system. Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage.

SW039

c. Close and lock the door and start a cycle.

Attempt to open the door while the cycle is in progress. The door should not open.

If the door lock and interlock are not functioning properly, call a service technician.

3. Do not attempt to operate the machine if any of the following conditions are present:

a. The door does not remain securely locked

during the entire cycle.

b. Excessively high water level is evident.

c. Machine is not connected to a properly

grounded circuit.

9002062

Page 9

Specifications and Dimensions

Overall Dimensions

Installation/Operation Supplement

General Specifications

Model 18 30

Overall width Overall height Overall depth Weight and Shipping Information Net weight Shipping weight Shipping volume Wash Cylinder Information Cylinder diameter Cylinder depth Cylinder volume Perforation size Door Opening Information Door opening size Height of door bottom above floor

660 mm (26 in.) 780 mm (30.7 in.)

1038 mm (40.9 in.) 1202 mm (47.3 in.)

739 mm (29.1 in.) 842 mm (33.1 in.)

211 kg (465.2 lb.) 325kg (716.5 lb.)

233 kg (513.7 lb.) 355 kg (782.6 lb.)

0.8 m

(22.5 ft3) 1.3 m3 (34.7 ft3)

530 mm (20.9 in.) 650 mm (25.6 in.)

330 mm (13 in.) 400 mm (15.76 in.)

76 l (2.7 ft

3 mm (0.12 in.) 3 mm (0.12 in.)

300 mm (11.8 in.) 300 mm (11.8 in.)

280 mm (11 in.) 381 mm (15 in.)

) 132 l (4.66 ft3)

Water Consumption

Average water consumption per cycle

Power Consumption

Average power used per cycle

9002062

HOT

COLD

Motor

Heating

11 l (3 gal.) 49 l (13 gal.)

68 l (18 gal.) 102l l (27 gal.)

0.15 kW/hr 0.2 kW/hr

1.5 kW/hr 3 kW/hr

Page 10

Installation/Operation Supplement

Model 18 30

Drive Train Information

General Specifications

Number of motors in drive train Drive motor power Cylinder Speeds Wash/reverse speed Distribution/drain speed Extract speed Centrifugal Force Data Wash/reverse centrifugal force Extract centrifugal force Balance Detection Vibration safety switch installed Electrical Heating (International Models Only) Total electrical heating capacity Electrical heating elements Electrical heat element size

1 HP (0.75 kW) 2 HP (1.5 kW)

10-50 RPM 10-50 RPM

85 RPM 85 RPM

250-1000 RPM 250-1000 RPM

0.03-0.74 Gs 0.04-0.91 Gs

19-296 Gs 23-363 Gs

Standard Standard

9 kW 18 kW

3 kW 3 kW

9002062

Page 11

1038 mm

(40.9 in.)

1011 mm

(39.8 in.)

365 mm

(14.4 in.)

Installation/Operation Supplement

220 mm

(8.7 in.)

65 mm

(2.6 in.)

231 mm

(9.1 in.)

75 mm

(3 in.)

530 mm

(20.9 in.)

660 mm

(26 in.)

153 mm

(6 in.)

65 mm

(2.6 in.)

184 mm (7.2 in.)

139 mm

(5.5 in.)

69 mm

(2.7 in.)

670 mm (26.3 in.)

727 mm (28.6 in.)

2 3

843 mm

(33.2 in.)

633 mm

(27.7 in.)

660 mm

(26 in.)

(31.9 in.)

180 mm

(7 in.)

809 mm

70 mm

(2.8 in.)

18 MODEL

1 Hot Water Connections 19 mm (.75 in.) 5 Drain Outlet 2 Power Input 6 Cold Water Inlet (required) 19 mm (.75 in.) 3 Emergency Stop Button 7 Cold Water Inlet (required) 19 mm (.75 in.) 4 Ventilation Tub 8 Fill and Supply Ventilation

CFD513N

9002062

Figure 1

Page 12

Installation/Operation Supplement

1202 mm

(474 in.)

1175 mm

(46.3 in.)

88 mm

(3.5 in.)

475 mm

(18.7 in.)

220 mm

(8.7 in.)

66 mm

(2.6 in.)

332 mm

(13.1 in.)

202 mm

(8 in.)

648 mm

(25.5 in.)

780 mm

(30.7 in.)

(10.5 in.)

267 mm

66 mm

(2.6 in.)

82 mm

(3.2 in.)

200 mm

(7.9 in.)

155 mm

(6.1 in.)

760 mm (29.9 in.)

816 mm (32.1 in.)

3 4

964 mm

200 mm (7.9 in.)

(38 in.)

70 mm

(2.8 in.)

CFD514N

924 mm

(36.4 in.)

849 mm

(33.5 in.)

35 mm

(1.4 in.)

30 MODEL

1 Hot Water Connections 19 mm (.75 in.) 5 Ventilation Tub 2 Cold Water Inlet (required) 19 mm (.75 in.) 6 Drain Outlet 3 Power Input 7 Cold Water Inlet (required) 19 mm (.75 in.) 4 Emergency Stop Button 8 Fill and Supply Ventilation

CFD514N

Figure 2

9002062

Page 13

Installation

Installation/Operation Supplement

Dimensional Clearances

Tab l e 1 shows recommended minimum clearances on all sides of the washer-extractor.

Recommended Minimum Clearances

Model 18 30

Minimum rear clearance

Minimum clearance between machine and wall

Minimum clearance between machines (side)

Minimum front clearance (door swing)

Table 1

600 mm

(24 in.)

150 mm

(6 in.)

25.4 mm (1 in.)

419 mm

(16.5 in.)

600 mm

(24 in.)

150 mm

(6 in.)

25.4 mm (1 in.)

419 mm

(16.5 in.)

Machine Foundation

Thoroughness of detail must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract.

CAUTION

Ensure that the machine is installed on a level floor of sufficient strength and that the recommended clearances for inspection and maintenance are pro vided. Never allow the inspection and maintenance space to be blocked.

W488

The washer-extractor must be placed on a smooth level surface so that the entire base of the machine is supported and rests on the mounting surface.

The standard installation does not require anchoring unless mandated by state or local codes.

Kinetic energy of the cylinder and dynamic loads on the floor or foundation are shown in Tab l e 2.

Tab l e 2 can be used as a reference when designing floors and foundations.

Floor Load Data

Model 18 30

Kinetic energy of the

cylinder

Dynamic bottom load

1386 N/m 2592 N/m

700 N/16 Hz 1000 N/16 Hz

Table 2

9002062

Page 14

Installation/Operation Supplement

Mounting Bolt Installation (If Required)

152 mm

(6 in.)

1 Base Frame 2 Bolt 3 Washer 4 Anchor Bolt/Plug

After the concrete has cured and the anchors are installed, proceed as follows:

1. Place the washer-extractor adjacent to the foundation. Do not attempt to move it by pushing on the sides. Always insert a pry bar or other device under the bottom of the frame of the washer-extractor to move it.

2. Place the washer-extractor carefully over the anchors.

3. Put bolts through the machine in the anchors and fasten them. The diameter of the bolt must be minimum 1/2-13 or 12 mm.To level machine, fill the spaces between the machine base and floor with machinery grout. Grout completely under all frame members. Remove front and rear panels to gain access to all frame members. Force grout under the machine base until all voids are filled.

4. Remove the spacers carefully, allowing the machine to settle into the wet grout.

CFS485N

5. Position washers and locknuts on machinery anchor bolts and fingertighten to machine base.

6. After the grout is completely dry, tighten the locknuts by even increments – one after the other – until all are tightened evenly and the machine is fastened securely to the floor.

Figure 3

9002062

Page 15

Installation/Operation Supplement

Removing the Transport Block

WARNING

The machine must never be activated before removing the transport block.

W618

To prevent damage during transportation, machine has been equipped with a transport block. To remove, proceed as follows:

1. Place machine on level ground.

2. Remove service panels and back panel.

3. At rear of machine, lift at bottom of motor and remove transport block if present. Refer to Figure 4.

IMPORTANT: Do NOT remove panel braces. They may be located in either the front or on the side and rear of the machine. Refer to Figure 5.

CFD515N

CFD34N

CFD26N

1 Transport Block (Remove)

Figure 4

IMPORTANT: Do NOT lift motor by the pulley.

4. Remove the panel braces. Refer to Figure 5.

CFD34N

CFD515N

1 Panel Braces

Figure 5

5. Replace all panels removed.

9002062

Page 16

Installation/Operation Supplement

Electrical Specifications

Model

Voltage Designation Standard Electric Heat

Full Load

Code

Voltage

Cycle

Phase

Wire

Amps

Breaker

Circuit

AWG/mm

Full Load

Breaker

Amps

Circuit

P 380-415 50/60 3 3+N+PE Not available 21 30 10/6.0 9

Q 200-240 50/60 3 3+PE Not available 27 30 10/6.0 9

X 200-240 50/60 1/3 2/3+PE 12 16 14/2.5 0.75 Not available

P 380-415 50/60 3 3+N+PE Not available 36 40 8/10.0 18

Q 200-240 50/60 3 3+PE Not available 49 60 6/16.0 18

X 200-240 50/60 1/3 2/3+PE 13 20 12/4.0 1.5 Not available

Tab le 3

AWG/mm

9002062

Page 17

Control Panel

Installation/Operation Supplement

Operation

NORMAL

RM RESS

WASH

ADD

BLEACH

RINSE

SPIN

DOOR

START

DOMESTIC MODELS

PE P

HOT

WARM

NORMAL

PERM PRESS

WARM

COLD

QUICK AS QUICK WASH

HOT

WARM

HEAVY SOIL

DELICATE

COLD

HOT

103

CHM482R

INTERNATIONAL MODELS

CHM482R CHM488R

95C 95C

60C 60C

40C 40C

1 Cycle 1 7 Cycle 7 2 Cycle 2 8 Cycle 8 3 Cycle 3 9 Down Edit/Change keypad 4 Cycle 4 10 Up Edit/Change keypad 5 Cycle 5 11 Start/Enter keypad 6 Cycle 6 12 Display

Figure 6

30C

CHM488R

9002062

Page 18

Installation/Operation Supplement

Operating Instructions

1. Turn on main power source (circuit breaker).

2. Pull door handle away from machine to open door. On some models it may be necessary to push handle’s button. Refer to Figure 7.

CFD516N

Figure 7

3. Load to capacity whenever possible. DO NOT OVERLOAD. Refer to Figure 8.

NOTE: Underloading can cause out-of-balance conditions that can shorten machine life.

4. Close door by pushing door handle towards machine. Refer to Figure 9.

CFD517N

Figure 9

5. The default wash cycle will display.

NOTE: Perm Press Cold 60°C is the default cycle for coin models if none is selected.

NORMAL

RM RESS

PE P

WASH

ADD

BLEACH

RINSE

SPIN

DOOR

START

HOT

WARM

NORMAL

PERM PRESS

WARM

COLD

QUICK AS QUICK WASH

HOT

WARM

HEAVY SOIL

DELICATE

COLD

HOT

Figure 8

CFD53N

DOMESTIC MODELS

95C 95C

60C 60C

40C 40C

INTERNATIONAL MODELS

Figure 10

30C

CHM488R

CHM482R

CHM488R

Page 19

Installation/Operation Supplement

6. If desired, select a different cycle at this point before satisfying vend. The LED indicator for that cycle will light.

7. Add liquid and/or powder supplies to supply dispenser. Refer to Figure 11.

a. Add detergent to compartment 1.

b. Add softener to compartment 3.

B157R

1 Detergent 2 Bleach 3 Softener

8. Add coins to machine. As each coin is added, the vend counts down to the amount remaining. Refer to Figure 11.

9. When applicable, add bleach to compartment 2 when the ADD BLEACH LED is lit.

10. Press the desired wash cycle keypad.

11. Press the START keypad and the active cycle remains the chosen wash cycle.

12. When cycle is complete, display shows “donE”.

Figure 11

9002062

Page 20

Installation/Operation Supplement

Disposal of Unit

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Refer to Figure 12. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact the local city office, household waste disposal service, or the source from which the product was purchased.

MIX1N

Figure 12

9002062