How it Works
Alliance Laundry Systems
Loading...
SC30NX2
Programming Manual
146 pgs4.53 Mb0
Troubleshooting Manual
72 pgs3.43 Mb0
Table of contents
Loading...

Alliance Laundry Systems HC25NX2, HC18NC2, HC25NC2, HC27NR2, HC18NX2 Programming Manual

...

NetMaster

Washer-Extractor

Cabinet Hard Mount Enhanced Programming Guide

Refer to Page 5 for Model Numbers

Programming
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
C872I
September 2004
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodil y injury and/or property damage.
W030
NOTE: The WARNINGS and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and carefulness are factors which cannot be built into these washer-extractors. These factors MUST BE supplied by the person(s) installing, maintaining, or operating the washer­extractor.
Always contact the distributor, service agent, or the manufacturer about any problems or conditions you do not understand.
800767
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1

Notes

2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
800767
Table of
Contents
Introduction......................................................................................... 5
Model Identification ............................................................................. 5
Entering the Manual Mode................................................................ 7
Programming NetMaster................................................................... 9
What Can Be Programmed? ................................................................. 9
Programmable Options Available......................................................... 10
1. Site Code #1 Hot Regular Wash Vend Price “+008” .................. 11
2. Site Code #1 Warm Regular Wash Vend Price “+009” .............. 13
3. Site Code #1 Cold Regular Wash Vend Price “+010”................. 15
4. Site Code #1 Hot Special Wash Vend Price “+011” ................... 17
5. Site Code #1 Warm Special Wash Vend Price “+012” ............... 19
6. Site Code #1 Cold Special Wash Vend Price “+013”.................. 21
7. Special Cycle Vend Price “+014”................................................ 23
8. Special Vend A Site Code #1 “+022” .......................................... 25
9. Start Pulse Value “+032”............................................................. 27
10. Power Fail Reset “+034” ............................................................. 29
11. Normal PreWash #2 Fill/Tumble Time “+043”........................... 31
12. Normal Rinse Extra Fill/Tumble Time “+046”........................... 32
13. Normal Spin Extract Speed “+049”............................................. 33
14. Normal Extracts On/Off “+050”.................................................. 34
15. Permanent Press PreWash #2 Fill/Tumble Time “+052”............ 37
16. Permanent Press Rinse Extra Fill/Tumble Time “+055”............. 38
17. Permanent Press Spin Extract Speed “+058”............................... 39
18. Permanent Press Extracts
On/Off “+059”............................................................................. 40
19. Delicates PreWash #1
Fill/Tumble Time “+060”............................................................ 43
20. Delicates PreWash #2
Fill/Tumble Time “+061”............................................................ 44
21. Delicates Rinse Extra Fill/Tumble Time “+064”......................... 45
22. Delicates Spin Extract Speed “+067”.......................................... 46
23. Delicates Extracts On/Off “+068”............................................... 47
24. Special Wash PreWash #2 Fill/Tumble Time “+070”................. 50
25. Special Wash Rinse Extra Fill/Tumble Time “+073”.................. 51
26. Special Wash Spin Extract Speed “+076”................................... 52
27. Special Wash Extracts On/Off “+077”........................................ 53
28. PreWash #1/PreWash #2/Rinses Water Temperature “+078”..... 56
29. Fill/Tumbles Water Levels #1 “+079”......................................... 58
30. Fill/Tumbles Water Levels #2 “+080”......................................... 60
31. Control Configuration Data #2 “+082”........................................ 62
32. Control Configuration Data #3 “+083”........................................ 66
33. Hot Water Temperature “+084”................................................... 68
34. Warm Water Temperature “+085”............................................... 70
35. Cold Water Temperature “+086”................................................. 72
36. PreWash #1 Fill/Tumble Dispenser “+087”................................ 74
37. PreWash #2 Fill/Tumble Dispenser “+088”................................ 76
38. Wash Fill/Tumble Dispenser “+089”........................................... 78
39. Rinse #1 Fill/Tumble Dispenser “+090”...................................... 80
40. Rinse Extra Fill/Tumble Dispenser “+091”................................. 82
© Copyright 2004, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
800767
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
41. Rinse Final Fill/Tumble Dispenser “+092” ................................. 84
42. PreWash #1 Fill/Tumble Drain “+093”....................................... 86
43. PreWash #1 Drain/Tumble Drain “+094”.................................... 88
44. PreWash #1 Extract Drain “+095”............................................... 90
45. PreWash #2 Fill/Tumble Drain “+096”....................................... 92
46. PreWash #2 Drain/Tumble Drain “+097”.................................... 94
47. PreWash #2 Extract Drain “+098”............................................... 96
48. Wash Fill/Tumble Drain “+099” ................................................. 98
49. Wash Drain/Tumble Drain “+100”.............................................. 100
50. Wash Extract Drain “+101”......................................................... 102
51. Rinse #1 Fill/Tumble Drain “+102” ............................................ 104
52. Rinse #1 Drain/Tumble Drain “+103”......................................... 106
53. Rinse #1 Extract Drain “+104”.................................................... 108
54. Rinse Extra Fill/Tumble Drain “+105” ........................................ 110
55. Rinse Extra Drain/Tumble Drain “+106”.................................... 112
56. Rinse Extra Extract Drain “+107” ............................................... 114
57. Rinse Final Fill/Tumble Drain “+108”........................................ 116
58. Rinse Final Drain/Tumble Drain “+109”..................................... 118
59. Rinse Final Extract Drain “+110”................................................ 120
60. Spin Extract Drain “+111”........................................................... 122
61. Spin Shakeout Drain “+112” ....................................................... 124
62. Water Inlet “+113”....................................................................... 126
63. Special Cycle Option “+115”....................................................... 129
64. Special Cycle Extra Wash Fill/Agitate Time “+116”.................. 131
65. Special Cycle Extra Rinse Extra Fill/Agitate Time “+117” ........ 132
66. Site Code #1 “+122”.................................................................... 133
67. Error Code Programming Parameter “+123”............................... 135
68. Start Pulse Mode “+124”............................................................. 143
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
800767

Introduction

Model Identification

Information in this manual is applicable to these models:

HC18NC2 HC60NX2 NC40NX2 SC30NR2 HC18NR2 HC80NCV NC50NC2 SC30NX2 HC18NX2 HC80NRV NC50NP2 SC35NC2 HC25NC2 HC80NXV NC50NR2 SC35N R2 HC25NR2 NC18NC2 NC50NX2 SC35NX2 HC25NX2 NC18NP2 NC80NCV SC40NC2 HC27NC2 NC18NR2 NC80NPV SC40NR2 HC27NR2 NC18NX2 NC80NRV SC40NX2 HC27NX2 NC25NC2 NC80NXV SC50NC2 HC30NC2 NC25NP2 SC18NC2 SC50NR2 HC35NC2 NC25NR2 SC18NR2 SC50NX2 HC35NR2 NC25NX2 SC18NX2 SC60NC2 HC35NX2 NC27NC2 SC20NC2 SC60NCF HC40NC2 NC27NP2 SC20NR2 SC60NR2 HC40NR2 NC27NR2 SC20NX2 SC60NRF HC40NX2 NC27NX2 SC25NC2 SC60NX2 HC50NC2 NC35NC2 SC25NR2 SC80NCV HC50NR2 NC35NP2 SC25NX2 SC80NRV HC50NX2 NC35NR2 SC27NC2 SC80NXV HC60NC2 NC35NX2 SC27NR2 HC60NCF NC40NC2 SC27NX2 HC60NR2 NC40NR2 SC30NC2

F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5

Notes

6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152

Entering the Manual Mode

For programming, testing, and retrieving information from NetMaster, it is often necessary to enter the Manual Mode by following the four simple step s below.

How to Enter the Manual Mode

1. Be sure the washer-extractor is in the Ready Mode before continuing to step 2. Refer to Figure 1. If the washer-extractor is in an acti v e c ycle, rapid advance through the cycle. Refer to Rapid Advance Feature section of the Basic Programming Guide. If coins have been entered, refer to Clear Vend Fe ature section of the Basic Programming Guide.

3. While pressing and holding the NORMAL keypad with one hand, press the HOT keypad with the other hand.

4. The VFD display will show “rAPd”. Refer to Figure 2.

B30R
Figure 2

5. Press the DELICATES (+) or the COLD (-) keypad to scroll through the options until the desired option appears in the VFD.

6. Press the START (enter) keypad.

Figure 1
2. Open the access panel. Refer to Opening the Access Panel section of the Basic Programming
Guide.
C854I
For additional information on the Manual Mode, refer to Entering Manual Mode section of the Basic Programming Guide.
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7

Notes

8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152

Programming NetMaster

What Can Be Programmed?

This feature allows the owner to program cycle information, standard vend pricing, special vends and otherfeatures by using the keypads. The control must have the Manual Programming Mode enabled, which is the factory default. This mode can only be turned OFF and ON by using the Micro-Wand IIIE, the Smart Card Reader, or the Network. Refer to this section when programming NetMaster.
This section offers a detailed description of options available to program. Additional options can be found in the Basic Programming Guide.
Each description includes instructions on when and why the option might be used and, more importantly, how to program the option.
For more advanced users, a quick reference list of the options available through the programming mode is located on the following page.
NOTE: The thr ee numbers in the Option column of the Programmable Options List are what will be shown in the VFD display when that option is selected.
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Programming NetMaster

Programmable Options Available

OPTION DESCRIPTION
008 Site Code #1 Hot Regular Wash Vend Price 009 Site Code #1 Warm Regular Wash Vend Price 010 Site Code #1 Cold Regular Wash Vend Price 011 Site Code #1 Hot Special Wash Vend Price 012 Site Code #1 Warm Special Wash Vend Price 013 Site Code #1 Cold Special Wash Vend Price 014 Special Cycle Vend Price 022 Special Vend A Site Code #1 032 Start Pulse Value 034 Power Fail Reset 043 Normal PreWash #2 Fill/Tumble Time 046 Normal Rinse Extra Fill/Tumble Time 049 Normal Spin Extract Speed 050 Normal Extracts On/Off 052 Permanent Press PreWash #2 Fill/Tumble
Time
055 Permanent Press Rinse Extra Fill/Tumble
Time 058 Permanent Press Spin Extract Speed 059 Permanent Press Extracts On/Off 060 Delicates PreWash #1 Fill/Tumble Time 061 Delicates PreWash #2 Fill/Tumble Time 064 Delicates Rinse Extra Fill/Tumble Time 067 Delicates Spin Extract Speed 068 Delicates Extracts On/Off 070 Special Wash PreWash #2 Fill/Tumble Time 073 Special Wash Rinse Extra Fill/Tumble Time 076 Special Wash Spin Extract Speed 077 Special Wash Extracts On/Off 078 PreWash #1/PreWash #2/Rinses Water
Temperature 079 Fill/Tumbles Water Levels #1 080 Fill/Tumbles Water Levels #2 082 Control Configuration Data #2 083 Control Configuration Data #3 084 Hot Water Temperature 085 Warm Water Temperature 086 Cold Water Temperature 087 PreWash #1 Fill/Tumble Dispenser 088 PreWash #2 Fill/Tumble Dispenser
OPTION DESCRIPTION
089 Wash Fill/Tumble Dispenser 090 Rinse #1 Fill/Tumble Dispenser 091 Rinse Extra Fill/Tumble Dispenser 092 Rinse Final Fill/Tumble Dispenser 093 PreWash #1 Fill/Tumble Drain 094 PreWash #1 Drain/Tumble Drain 095 PreWash #1 Extract Drain 096 PreWash #2 Fill/Tumble Drain 097 PreWash #2 Drain/Tumble Drain 098 PreWash #2 Extract Drain 099 Wash Fill/Tumble Drain 100 Wash Drain/Tumble Drain 101 Wash Extract Drain 102 Rinse #1 Fill/Tumble Drain 103 Rinse #1 Drain/Tumble Drain 104 Rinse #1 Extract Drain 105 Rinse Extra Fill/Tumble Drain 106 Rinse Extra Drain/Tumble Drain 107 Rinse Extra Extract Drain 108 Rinse Final Fill/Tumble Drain 109 Rinse Final Drain/Tumble Drain 110 Rinse Final Extract Drain 111 Spin Extract Drain 112 Spin Shakeout Drain 113 Water Inlet 115 Special Cycle Option 116 Special Cycle Extra Wash Fill/Agitate Time 117 Special Cycle Extra Rinse Extra Fill/Agitate
Time 122 Site Code #1 123 Error Code Programming Parameter 124 Start Pulse Mode
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

8. Site Code #1 Hot Regular Wash Vend Price “+008”

This option allows the owner to set the vend price for a hot regular wash when cards with a special site code are used by specific groups or individuals.
How to Program the Site Code #1 Hot Regular Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+008” appears in the VFD, press the
START (enter) keypad. There are five digits in the Site Code #1 Hot Regular Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 5.
C826I
Figure 5
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 6.
1
C762I
Figure 3
3. Press the DELICA TES (+) or the COLD (-) keypad to scroll through the programmable options until “+008” appears in the VFD. Refer to Figure 4.
C770I
Figure 4
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 6
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 7.
C827I
Figure 7
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+009”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+009” (Site Code #1 Warm Regular Wash Vend Price), refer to option 9. To program other options, refer to the appropriate section.
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

9. Site Code #1 Warm Regular Wash Vend Price “+009”

This option allows the owner to set the vend price for a warm regular wash when cards with a special site code are used by specific groups or individuals.
How to Program the Site Code #1 Warm Regular Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+009” appears in the VFD, press the
START (enter) keypad. There are five digits in the Site Code #1 Warm Regular Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one se cond o ff. Refer to Figure 10.
C826I
Figure 10
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 11.
1
C762I
Figure 8
3. Press the DELICA TES (+) or the COLD (-) keypad to scroll through the programmable options until “+009” appears in the VFD. Refer to Figure 9.
C771I
Figure 9
C771I
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 11
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 12.
C827I
Figure 12
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+010”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+010” (Site Code #1 Cold Regular Wash Vend Price), refer to option 10. To program other options, refer to the appropriate section.
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

10. Site Code #1 Cold Regular Wash Vend Price “+010”

This option allows the owner to set the vend price for a cold regular wash when cards with a special site code are used by specific groups or individuals.
How to Program the Site Code #1 Cold Regular Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+010” appears in the VFD, press the
ST ART (enter) keypad. There are five digits in the Site Code #1 Cold Regular Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to F i gur e 15 .
C826I
Figure 15
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 16.
1
Figure 13
3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+010” appears in the VFD. Refer to Figure 14.
C772I
Figure 14
C762I
C772I
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 16
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 17.
C827I
Figure 17
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+011”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+011” (Site Code #1 Hot Special Wash Vend Price), refer to option 11. To program other options, refer to the appropriate section.
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

11. Site Code #1 Hot Special Wash Vend Price “+011”

This option allows the owner to set the vend price for a hot special wash when cards with a special site code are used by specific groups or individuals.
How to Program the Site Code #1 Hot Special Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+011” appears in the VFD, press the
START (enter) keypad. There are five digits in the Site Code #1 Hot Special Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 20.
C826I
Figure 20
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 21.
1
C762I
Figure 18
3. Press the DELICA TES (+) or the COLD (-) keypad to scroll through the programmable options until “+011” appears in the VFD. Refer to Figure 19.
C773I
C773I
Figure 19
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 21
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 22.
C827I
Figure 22
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+012”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+012” (Site Code #1 Warm Special Wash Vend Price), refer to option 12. To program other options, refer to the appropriate section.
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

12. Site Code #1 Warm Special Wash Vend Price “+012”

This option allows the owner to set the vend price for a warm special wash when cards with a special site code are used by specific groups or individuals.
How to Program the Site Code #1 Warm Special Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+012” appears in the VFD, press the
START (enter) keypad. There are five digits in the Site Code #1 Warm Special Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one se cond o ff. Refer to Figure 25.
C826I
Figure 25
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 26.
1
C762I
Figure 23
3. Press the DELICA TES (+) or the COLD (-) keypad to scroll through the programmable options until “+012” appears in the VFD. Refer to Figure 24.
C774I
Figure 24
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 26
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 27.
C827I
Figure 27
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+013”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+013” (Site Code #1 Cold Special Wash Vend Price), refer to option 13. To program other options, refer to the appropriate section.
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

13. Site Code #1 Cold Special Wash Vend Price “+013”

This option allows the owner to set the vend price for a cold special wash when cards with a special site code are used by specific groups or individuals.
How to Program the Site Code #1 Cold Special Wash Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+013” appears in the VFD, press the
ST ART (enter) keypad. There are five digits in the Site Code #1 Cold Special Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to F i gur e 30 .
C826I
Figure 30
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 31.
1
Figure 28
3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+013” appears in the VFD. Refer to Figure 29.
Figure 29
C762I
C775I
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 31
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 32.
C827I
Figure 32
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+014”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+014” (Special Cycle Vend Price), refer to option 14. To program other options, refer to the appropriate section.
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

14. Special Cycle Vend Price “+014”

This option allows the owner to program the machines to offer extra features to the customers for an added vend price. This vend price will be displayed in the VFD during the first 30 seconds of the fi rst f ill/agitate. Refer to options 115, 116 and 117 for programming these features.
How to Program Special Cycle Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+014” appears in the VFD, press the
START (enter) keypad. There are five digits in the Special Cycle Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 35.
C826I
Figure 35
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number until correct. Refer to Figure 36.
1
Figure 33
3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+014” appears in the VFD. Refer to Figure 34.
C776I
Figure 34
C762I
C776I
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 36
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display the remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 37.
C827I
Figure 37
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+015”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+015” (Special Vend A Days Enable), refer to option 15 in Programming NetMaster in the Basic Programming Guide. To program other options, refer to the appropriate section.
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

22. Special Vend A Site Code #1 “+022”

This option allows the owner to program the machines to accept site codes for Special Vend A that are specific to select groups or individuals when using cards. It allows the owner to only give Special Vend A pricing for a card with this site code. If Special Vend A Site Code is zero, then Special Vend A pricing will apply to all cards.
How to Program the Special Vend A Site Code #1
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
4. When “+022” appears in the VFD, press the
START (enter) keypad. There are five digits in the Special Vend A Site Code #1. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 40.
C826I
Figure 40
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 41.
1
Figure 38
3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+022” appears in the VFD. Refer to Figure 39.
C790I
Figure 39
C762I
C790I
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
Figure 41
neednew#2
B029R
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 42.
C828I
Figure 42
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+023”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+023” (Special Vend A Regular Hot W ash Vend Price), refer to option 23 in Programming NetMaster in the Basic Programming Guide. To program other options, refer to the appropriate section.
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Programming NetMaster

32. Start Pulse Value “+032”

This option allows the owner to program the value of the Start Pulse if used for multiple pulses with an after­market central card reader or pay system. Refer to option 124 for additional information.
How to Program Start Pulse Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the DELICATES (+) or the COLD (-)
keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.
C762I
4. When “+032” appears in the VFD, press the START (enter) keypad. There are five digits in the Start Pulse Value. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 45.
C826I
Figure 45
5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 46.
1
Figure 43
3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+032” appears in the VFD. Refer to Figure 44.
C780I
Figure 44
C780I
32
1 Press this pad (+) to scroll forward or increase a va lue 2 Press this pad (enter) to choose a selected value or
option
3 Press this pad (-) to scroll back or decrease a value
neednew#2
B029R
Figure 46
F232152
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Programming NetMaster
6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 47.
C827I
Figure 47
7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.
8. Press the START (enter) keypad with the last active digit. The ne xt option, “+033”, will appear in the VFD.
How to Exit Programming Feature
1. Be sure the control shows a programmable option, not a value.
2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode.
NOTE: To program “+033” (Default Cycle/ Temperature), refer to option 33 in Programming NetMaster in the Basic Programming Guide. To program other options, refer to the appropriate section.
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232152
Loading...
+ 116 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use