Alliance Laundry Systems CS075, CS100, CS135, CS165, CXG060 Original Instructions Manual

...

Washer-Extractors

CFD

CFD644N

Cabinet Freestanding

Refer to for Page 5 Model Identification

Installation

Original Instructions Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.alliancelaundry.com

Part No. D1343ENR3

November 2012

Table of

Contents

Safety Information.............................................................................. 2

Explanation of Safety Messages........................................................... 2

Important Safety Instructions ............................................................... 2

Safety Decals ........................................................................................ 4

Introduction......................................................................................... 5

Model Identification ............................................................................. 5

Nameplate Location.............................................................................. 6

Replacement Parts ................................................................................ 6

Customer Service.................................................................................. 6

Specifications and Dimensions........................................................... 7

Installation........................................................................................... 15

Dimensional Clearances................................................................... 15

Machine Foundation ........................................................................ 16

Mechanical Installation......................................................................... 17

Frame Dimensions and Mounting Bolt Location

For 12 lb. (60 l ), 14 lb. (65 l),

18 lb. (75 l) and 25 lb. (100 l) Capacity Models ............................ 17

Frame Dimensions and Mounting Bolt Location

For 30 lb. (135 l) and 35 lb. (165 l) Capacity Models.................... 18

Frame Dimensions and Mounting Bolt Location

For 55 lb. (235 l) and 75 lb. (305 l) Capacity Models.................... 19

Mounting Bolt Installation (If Required).............................................. 20

Removing the Transport Brackets ........................................................ 21

Drain Connection.................................................................................. 22

Water Connection ................................................................................. 24

Electrical Installation ............................................................................ 25

Electrical Connection............................................................................ 28

Remote Liquid Supply Connection ...................................................... 29

Chemical Injection Supply System.................................................. 29

Steam Requirements (Steam Heat Option Only).................................. 30

Supply Programming Table ............................................................. 31

Supply Relay Configuration (No Wiring)........................................ 31

Primary 220 Volt Remote Liquid Supply Connection..................... 31

Out-of-Balance Switch ......................................................................... 33

Automatic Lubricator............................................................................ 33

Control Function Test........................................................................... 34

Disposal of Unit................................................................................... 35

means without the expressed written consent of the publisher.

D1343

Safety Information

DANGER indicates the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the danger is ignored.

DANGER

WARNING indicates the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

WARNING

CAUTION indicates the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

CAUTION

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

WARNING

Explanation of Safety Messages

Precautionary statements (“DANGER”, “WARNING”, and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

Important Safety Instructions

1. Read all instructions before using the washer.

2. Install the washer according the INSTALLATION instructions. Refer to the EARTHING (grounding) instructions in the INSTALLATION manual for the proper earthing (grounding) of the washer. All connections for water, drain, electrical power and earthing (grounding) must comply with local codes and be made by licensed personnel when required. It is recommended that the machine be installed by qualified technicians.

3. Do not install or store the washer where it will be exposed to water and/or weather.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

4. To prevent fire and explosion, keep the area around machine free from flammable and combustible products. Do not add the following substances or textiles containing traces of the following substances to the wash water: gasoline, kerosene, waxes, cooking oils, vegetable oils, machine oils, dry-cleaning solvents, flammable chemicals, thinners, or other flammable or explosive substances. These substances give off vapors that could ignite, explode or cause the fabric to catch fire by itself.

5. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable, do not smoke or use an open flame during this time.

6. To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electrical power source.

Safety Information

7. Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. This is a safety rule for all appliances.

8. DO NOT reach and/or climb into the tub or onto the washer, ESPECIALLY if the wash drum is moving. This is an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

9. Never operate the washer with any guards, panels and/or parts removed or broken. DO NOT bypass any safety devices or tamper with the controls.

10. Use washer only for its intended purpose, washing textiles. Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket or tub.

11. Use only low-sudsing, no-foaming types of commercial detergent. Be aware that hazardous chemicals may be present. Wear hand and eye protection when adding detergents and chemicals. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times (preferably in a locked cabinet).

12. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

13. Always follow the fabric care instructions supplied by the textile manufacturer.

17. Do not operate the machine without the water reuse plug or water reuse system in place, if applicable.

18. Be sure water connections have a shut-off valve and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day.

19. Keep washer in good condition. Bumping or dropping the washer can damage safety features. If this occurs, have washer checked by a qualified service person.

20. DANGER: Before inspecting or servicing machine, power supply must be turned OFF. The servicer needs to wait for at least 10 minutes after turning the power OFF and needs to check for residual voltage with a voltage meter. The inverter capacitor or EMC filter remains charged with high voltage for some time after powering OFF. This is an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.

21. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out. ALWAYS disconnect the washer from electrical, power and water supplies before attempting any service.

22. Disconnect the power cord by grasping the plug, not the cord. Replace worn power cords and/or loose plugs. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the service agent.

23. Before the washer is removed from service or discarded, remove the door to the washing compartment.

14. Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open. Do not attempt to open the door until the washer has drained and all moving parts have stopped.

15. Be aware that hot water is used to flush the supply dispenser. Avoid opening the dispenser lid while the machine is running.

16. Do not attach anything to the supply dispenser’s nozzles, if applicable. The air gap must be maintained.

D1343

24. Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer.

Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do not understand.

Safety Information

This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty.

SW004

WARNING

Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.

SW014

WARNING

IMPORTANT: Ensure that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

Safety Decals

Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician.

Use manufacturer-authorized spare parts to avoid safety hazards.

D1343

Introduction

Model Identification

Information in this manual is applicable to these models:

CS018 CS025 CS035 CS055 CS075 CS100 CS135 CS165 CXG060 CXG065 CXG075 CXG100 CXG135 CXG165 CXG235 CXG305 CXN060 CXN065 CXN075 CXN100 CXN135 CXN165 CXN235 CXN305 CXU060 CXU065 CXU075 CXU100 CXU135 CXU165 CXU235 CXU305 CXW060 CXW065 CXW075 CXW100 CXW135 CXW165 CXW235

CXW305 CXZ060 CXZ065 CXZ075 CXZ100 CXZ135 CXZ165 CXZ235 CXZ305 DXU060X DXU065X DXU075X DXU100X DXU135X DXU165X DXU235X DXU305X HD60 HD65 HD75 HD100 HD135 HD165 HD235 HD305 HX18 HX25 HX35 HX55 HX75 HXN075P HXN100P HXN165P HXN235P HXN305P IS012 IS018 IS025 IS035

IS055 IS075 IS100 IS135 IS165 IXG060 IXG065 IXG075 IXG100 IXG135 IXG165 IXG235 IXG305 IXN060 IXN065 IXN075 IXN100 IXN135 IXN165 IXN235 IXN305 IXU060 IXU065 IXU075 IXU100 IXU135 IXU165 IXU235 IXU305 IXW060 IXW065 IXW075 IXW100 IXW135 IXW165 IXW235 IXW305 IXZ060 IXZ065

IXZ075 IXZ100 IXZ135 IXZ165 IXZ235 IXZ305 JXW060C JXW060X JXW060Y JXW060Z JXW065C JXW065X JXW065Y JXW065Z JXW075C JXW075X JXW075Y JXW075Z JXW100C JXW100X JXW100Y JXW100Z JXW135C JXW135X JXW135Y JXW135Z JXW165C JXW165X JXW165Y JXW165Z JXW235C JXW235X JXW235Y JXW235Z JXW305C JXW305X JXW305Y JXW305Z PXU060Y

PXU065Y PXU075Y PXU100Y PXU135Y PXU165Y PXU235Y PXU305Y SX18 SX25 SX35 SX55 SX75 SXN075P SXN100P SXN165P SXN235P SXN305P UX18 UX25 UX35 UX55 UX75 UXN075P UXN100P UXN165P UXN235P UXN305P WXU060C WXU065C WXU075C WXU100C WXU135C WXU165C WXU235C WXU305C

D1343

Introduction

CFD644N

Nameplate Location

The nameplate is located at the rear of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1.

1 Nameplate

Customer Service

For technical assistance, contact your local distributor or contact:

Alliance Laundry Systems

Shepard Street

P. O . B ox 99 0

Ripon, Wisconsin 54971-0990

U.S.A.

www.alliancelaundry.com

Phone: +1 (920) 748-3121

+3256412054

Wevelgem, Belgium

Figure 1

Replacement Parts

If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at +1 (920) 748-3950 for the name and address of the nearest authorized parts distributor.

D1343

Specifications and Dimensions

General Specifications

Capacity lb. (l) 12 (60) 14 (65) 18 (75) 25 (100) 30 (135) 35 (165) 55 (235) 75 (305)

Overall Dimensions

Overall width 26 in.

(660 mm)

Overall height 40.6 in.

(1031 mm)

Overall depth 30.7 in.

(780 mm)

Weight and Shipping Information

Net weight

465 lb.

(211 kg)

Net weight 520 lb.

(236 kg)

Shipping weight 514 lb.

(233 kg)

Shipping weight 624 lb.

(283 kg)

Shipping volume

22.5 ft

(0.8 m

Wash Cylinder Information

Cylinder diameter 20.9 in.

(530 mm)

Cylinder depth 9.8 in.

(250 mm)

Cylinder volume

1.94 ft (55 l)

Perforation size 0.1 in.

(3 mm)

Door Opening Information

Door opening size

11.8 in.

(300 mm)

Height of door bottom above floor

11 in.

(279 mm)

(1031 mm)

)

26 in.

(660 mm)

40.6 in.

34.3 in.

(870 mm)

520 lb.

(236 kg)

531 lb.

(241 kg)

569 lb.

(258 kg)

639.5 lb. (290 kg)

24.5 ft

(0.9 m

20.9 in.

(530 mm)

11.6 in.

(295 mm)

2.30 ft3 (65 l)

0.1 in.

(3 mm)

11.8 in.

(300 mm)

11 in.

(279 mm)

30.71 in.

(780 mm)

47.3 in.

(1202 mm)

33.1 in.

(842 mm)

716.5 lb. (325 kg)

N/A N/A

782.6 lb. (355 kg)

N/A N/A

34.7 ft

)

(1.3 m

20.9 in.

(530 mm)

13.0 in.

(330 mm)

2.58 ft3 (73 l)

0.12 in.

(3 mm)

11.8 in.

(300 mm)

11 in.

(279 mm)

)

30.71 in.

(780 mm)

54.15 in.

(1376 mm)

33.07 in.

(840 mm)

811.30 lb. (368 kg)

844.37 lb. (383 kg)

42.83 ft

(1.21 m

20.9 in.

(530 mm)

17.3 in.

(440 mm)

3.35 ft3 (95 l)

0.1 in.

(3 mm)

11.8 in.

(300 mm)

11 in.

(279 mm)

30.8 in.

(783 mm)

47 in.

(1194 mm)

37.8 in.

(960 mm)

789 lb.

(358 kg)

765 lb.

(347 kg)

855 lb.

(388 kg)

1030 lb. (467 kg)

34.7 ft

)

(1.3 m

25.6 in.

(650 mm)

15.7 in.

(400 mm)

4.66 ft3 (132 l)

0.1 in.

(3 mm)

15.75 in.

(400 mm)

11.61 in.

(295 mm)

(1376 mm)

)

30.71 in.

(780 mm)

54.15 in.

37.01 in.

(940 mm)

862.01 lb. (391 kg)

N/A

921.53 lb. (418 kg)

N/A

45.98 ft

(1.3 m

)

25.6 in.

(650 mm)

19.7 in.

(500 mm)

5.83 ft3 (165 l)

0.1 in.

(3 mm)

15.75 in.

(400 mm)

11.61 in.

(295 mm)

26 in.

(660 mm)

40.6 in.

(1031 mm)

30.7 in.

(780 mm)

465 lb.

(211 kg)

520 lb.

(236 kg)

514 lb.

(233 kg)

624 lb.

(283 kg)

22.5 ft

(0.8 m

29.5 in.

(750 mm)

20.9 in.

(530 mm)

8.26 ft3 (234 l)

0.1 in.

(3 mm)

15.75 in.

(400 mm)

20.87 in.

(530 mm)

)

(1031 mm)

26 in.

(660 mm)

40.6 in.

34.3 in.

(870 mm)

520 lb.

(236 kg)

531 lb.

(241 kg)

569 lb.

(258 kg)

639.5 lb. (290 kg)

24.5 ft

(0.9 m

33.5 in.

(850 mm)

21.1 in.

(537 mm)

10.74 ft3 (304 l)

0.1 in.

(3 mm)

15.75 in.

(400 mm)

22.24 in.

(565 mm)

)

D1343

Specifications and Dimensions

General Specifications

Capacity lb. (l) 12 (60) 14 (65) 18 (75) 25 (100) 30 (135) 35 (165) 55 (235) 75 (305)

Drive Train Information

Number of motors in drive

111111

train

Drive motor power 1.01 HP

(0.75 kW)

1.01 HP

(0.75 kW)

1.01 HP

(0.75 kW)

1.01 HP

(0.75 kW)

2.95 HP

(2.2 kW)

2.95 HP

(2.2 kW)

4.02 HP (3 kW)

5.36 HP (4 kW)

Cylinder Speeds

Wash/reverse speed 10-50

RPM

10-50

RPM

10-50

RPM

10-50

RPM

10-50

RPM

10-50

RPM

10-50

RPM

10-50

RPM

Distribution/drain speed 85 RPM 82 RPM 85 RPM 85 RPM 74 RPM 85 RPM 85 RPM 82 RPM

Extract speed 250-1000

RPM

250-1000

RPM

250-1000

RPM

250-1000

RPM

250-1000

RPM

250-1000

RPM

250-1000

RPM

250-1000

RPM

Centrifugal Force Data

Wash/reverse centrifugal force

0.03-0.74 Gs0.03-0.74 Gs0.4-0.91 Gs0.37-0.94 Gs0.04-0.91 Gs0.37-0.94 Gs0.03-0.74 Gs0.03-0.74 Gs

Extract centrifugal force 19-296 Gs 19-296 Gs 23-363 Gs 24-377 Gs 23-363 Gs 24-377 Gs NO DATA NO DATA

Balance Detection

Vibration safety switch

Standard Standard Standard Standard Standard Standard Standard Standard

installed

Direct Steam Heating (Optional)

Steam inlet connection size 1 x 3/8 in. 1 x 3/8 in. 1 x 3/8 in. 1 x 3/8 in. 1 x 3/8 in. 1 x 3/8 in. 1 x 3/8 in. 1 x 3/8 in.

Number of steam inlets11111111

Electrical Heating (Optional)

Total electrical heating

9 kW 9 kW 9 kW 9 kW 18 kW 18 kW 18 kW 18 kW

capacity

Electrical heating elements33336666

Electrical heat element size 3 kW 3 kW 3 kW 3 kW 3 kW 3kW 3 kW 3 kW

D1343

Specifications and Dimensions

CFD632N

CFS630N

12 LB. (60L), 14 LB. (65L), 18 LB. (75L) AND 25 LB. (100L) CAPACITY MODELS

F G

CFD631N

CFD632N

CFD631N

1 Fill and Supply Ventilation 6 External Liquid Supply Inlets 2 Direct Fill 7 Electrical Steam Input 3 Hot Water Inlet 8 External Supply Signal Input 4 Cold Water Inlet 9 Electrical Power Input 5 Flushing Supply Dispenser 10 Drain Outlet

D1343

11 Steam Connection Output

Figure 2

+ 29 hidden pages

Alliance Laundry Systems CS075, CS100, CS135, CS165, CXG060 Original Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual