Alliance Laundry Systems HC35NC2, HC50NC2, HC25NC2, HC27NC2, HC80NC2 Instructions Manual

...

Download

Page 1

NetMaster

Washer-Extractors

Cabinet Hardmount Basic Programming Guide

Refer to Page 5 for Model Numbers

Programming

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

C872I

Part No. F232151R2

April 2002

Page 2

Page 3

WARNING

Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

W030

NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness are factors which cannot be built into these washer-extractors. These factors MUST BE supplied by the person(s) installing, maintaining or operating the washerextractor.

Always contact the distributor, service agent or the manufacturer about any problems or conditions you do not understand.

F232151

Page 4

Notes

F232151

Page 5

Table of

Contents

Introduction......................................................................................... 5

Model Identification ............................................................................. 5

Preliminary Information.................................................................... 7

About the Control ................................................................................. 7

Glossary of Terms................................................................................. 7

Power Failure Recovery ....................................................................... 7

Communications................................................................................... 8

NetMaster Identification .................................................................... 9

Select Cycle Pads.................................................................................. 9

Select Wash Temp Pads........................................................................ 9

VFD Display Identification................................................................ 11

Light Emitting Diodes (LEDs) ............................................................. 11

Washer-Extractor Operation ............................................................ 13

Start Up................................................................................................. 13

Ready Mode.......................................................................................... 13

Cycle Sequence..................................................................................... 13

Closing Washer-Extractor Door ........................................................... 13

Signals................................................................................................... 14

Changing Cycles................................................................................... 14

NetMaster Special Features ............................................................... 15

Programming NetMaster ...................................................................... 15

Collecting Audit Information ............................................................... 15

Testing Machine and NetMaster Functions.......................................... 15

Sales Floor Feature ............................................................................... 15

Rapid Advance Feature......................................................................... 15

Clearing the NetMaster Vend Feature .................................................. 15

Communications Mode......................................................................... 15

Dual Coin Drop..................................................................................... 15

Start Pulse Operation............................................................................ 16

Access Panel and Coin Vault Openings ............................................... 16

Break-In Alarm..................................................................................... 16

Special Vend......................................................................................... 16

Lucky Cycle.......................................................................................... 16

Site Code Pricing.................................................................................. 16

Special Cycle ........................................................................................ 16

Auto-Flush Feature ............................................................................... 16

Opening the Access Panel .................................................................. 17

Entering the Manual Mode................................................................ 19

Programming NetMaster ................................................................... 21

What Can Be Programmed? ................................................................. 21

Programmable Options Available......................................................... 22

Collecting Audit Information ............................................................ 107

Manual Reset....................................................................................... 109

Testing Machine and NetMaster Functions ..................................... 111

Sales Floor Feature............................................................................. 121

Rapid Advance Feature...................................................................... 123

Clear Vend Feature ............................................................................ 125

Communications Mode ...................................................................... 127

Power Fail Recovery........................................................................... 129

Default Washer-Extractor Settings................................................... 131

means without the expressed written consent of the publisher.

F232151

Page 6

Notes

F232151

Page 7

Introduction

Model Identification

Information in this manual is applicable to these models:

HC18NC2 HC25NX2 NC25NR2 SC25NC2 SC80NRV

HC25NC2 HC27NX2 NC27NR2 SC27NC2 SC18NX2

HC27NC2 HC35NX2 NC35NR2 SC30NC2 SC20NX2

HC35NC2 HC40NX2 NC40NR2 SC35NC2 SC25NX2

HC40NC2 HC50NX2 NC50NR2 SC40NC2 SC27NX2

HC50NC2 HC80NXV NC80NRV SC50NC2 SC30NX2

HC80NCV NC18NC2 NC18NX2 SC80NCV SC35NX2

HC18NR2 NC25NC2 NC25NX2 SC18NR2 SC40NX2

HC25NR2 NC27NC2 NC27NX2 SC20NR2 SC50NX2

HC27NR2 NC35NC2 NC35NX2 SC25NR2 SC80NXV

HC35NR2 NC40NC2 NC40NX2 SC27NR2

HC40NR2 NC50NC2 NC50NX2 SC30NR2

HC50NR2 NC80NCV NC80NXV SC35NR2

HC80NRV HC25NX2 SC18NC2 SC40NR2

HC18NX2 NC18NR2 SC20NC2 SC50NR2

F232151

Page 8

Notes

F232151

Page 9

Preliminary Information

About the Control

NetMaster on the washer-extractor is an advanced, programmable computer that lets the owner control most machine features by pressing a sequence of SELECT CYCLE and SELECT WASH TEMP pads. Refer to Figure 1.

NetMaster allows the owner to program custom cycles, set vend prices, retrieve audit information, program and run diagnostic cycles, and program special vend features. Washer-extractors shipped from the factory have a default cycle and wash temperature setting of PERM PRESS, WARM built in. However, the owner can change the default cycle, or any cycle, as needs permit.

IMPORTANT: In the event of a power failure, NetMaster will not have to be reprogrammed. It is designed with a memory system that will remember how it was programmed (for a minimum of six years) until the electrical power is restored.

IMPORTANT: It is extremely important that the washer-extractor has a positive ground and that all mechanical and electrical connections to NetMaster are made before applying power to or operating the washer-extractor.

Glossary of Terms

The following are a few terms and abbreviations to learn. These are referred to throughout the instructions.

Power Failure Recovery

If a cycle is in progress and the power fails, cycle status is saved in memory (for a minimum of six years) without power being applied.

If power resumes within one minute and 30 seconds, the previously active cycle will continue without having to press START.

If the control was in a fill cycle step and if the preprogrammed pressure switch is not satisfied, the control will start the Fill/Tumble step from the beginning.

If the control was in an intermediate extract step, the rest of the extract step is lost and the control will resume in the next cycle step. However, if in the intermediate extract step prior to the final extract or in the final extract, the control will resume the cycle from the beginning of the previous Drain/Tumble step.

The owner may program a special feature called Power Fail Reset which sets a maximum power failure duration. To program this feature, refer to Programming NetMaster in the Enhanced Programming Guide, available at extra cost.

If power resumes anytime after one minute and 30 seconds and less than or equal to the time programmed by the owner for the Power Fail Reset, or if the Power Fail Reset feature is disabled, the control will enter into the Start Mode at the beginning of the cycle step where the power failed.

VFD - Vacuum Fluorescent Display.

This term refers to the window area of the control that displays words and values.

LED - Light Emitting Diode.

This term refers to the lights on the keypads and status words of the control.

F232151

If power resumes anytime after the time programmed by the owner, the control will revert to the Ready Mode.

For more information, refer to Power Fail Recovery.

Page 10

Preliminary Information

Communications

NetMaster may be programmed manually, by Micro-Wand IIIE, by the Card Reader or by the Network.

MICRO-WAND IIIE

Infra-red Communications (Optional)

The Micro-Wand allows the owner to program and retrieve information from NetMaster without touching the keypad. The Micro-Wand greatly expands the programming options available to the owner. However, the Micro-Wand is not required to program and operate the washer-extractor. The operation of the Micro-Wand and the advanced features available are covered separately in the Micro-Wand IIIE instruction manual.

ENTER

I C

I I

T M

C100I

C100

ENTER

Smart Card Reader Communications

The control will accept communication with a Card Reader in order to perform vending transactions when a card is inserted to pay for cycles. The card reader can also allow the owner to program and collect audit information.

For detailed information on the Smart Card Reader Communications, refer to the Smart Card setup module in the NetMaster Smart Card Suite software package.

Network Communications

The control will also accept communication with a Network Interface Board which allows the control to be linked to a personal computer. This network link allows an owner to program, collect data, and run diagnostics on any machine.

For detailed information on Network Communications, refer to the Network instruction manual.

I C

I I

T M

C100I

F232151

Page 11

NetMaster Identification

Select Cycle Pads (Refer to Figure 1)

SELECT CYCLE pads are used to select the specific washer-extractor cycle. These pads include NORMAL, PERM PRESS, DELICATES and SPECIAL WASH. These pads allow the user to select a cycle other than the default cycle (PERM PRESS). The SELECT CYCLE keypads are not active after the first fill cycle of the washer-extractor. The selected cycle is indicated by the light (LED) on the pad. Pressing the START pad will confirm the selection and the cycle will begin. When the Smart Card is used, the START pad flashes. Pressing the START pad will start the cycle and deduct the vend price from the card.

Select Wash Temp Pads (Refer to Figure 1)

SELECT WASH TEMP pads are used to select the temperature of the water used for the wash fill/tumble. These pads include HOT, WARM and COLD. These pads allow the user to select a water temperature other than the default setting (WARM). The SELECT WASH TEMP pads are active only during the first fill/ tumble cycle of the washer. The selected temperature is indicated by the light (LED) on the pad.

Both the SELECT WASH TEMP pads and the SELECT CYCLE pads are used in various combinations for programming cycles, retrieving audit information, running diagnostic tests and other hidden operations. These instructions cover the basic manual programming and data retrieval options.

C872I

ELECTRONIC DISPLAY CONTROL

1 LED Light 5 VFD Display 2 LED Status Lights 6 START pad 3 SELECT CYCLE pads (top row) 7 SELECT WASH TEMP pads (bottom row) 4 Four 7-Segment Digits

Figure 1

C872I

F232151

Page 12

Notes

F232151

Page 13

VFD Display Identification

Light Emitting Diodes (LEDs) (Refer to Figure 1)

LIGHT EMITTING DIODES (LEDs) are used to indicate the chosen cycle, wash temperature, cycle status and door lock information. Refer below for information on each LED.

CYCLE LED (NORMAL, PERM PRESS, DELICATES or SPECIAL WASH)

CYCLE LED will remain lit the entire cycle.

WASH TEMP LED (HOT, WARM or COLD)

WASH TEMP LED will remain on until the end of the cycle or will change to a rinse temperature if programmed to do so.

WASH LED

WASH LED is lit at the beginning of a PreWash and Wash cycle and will remain lit until the wash cycle is complete.

RINSE LED

RINSE LED is lit at the beginning of the Rinse or Extra Rinse cycle and will remain lit until the cycle is complete.

SPIN LED

SPIN LED is lit for all Spin cycles.

CLEAN FILTER (VFD Models Only)

CLEAN FILTER LED is lit when the air filter needs to be cleaned.

ADD BLEACH

ADD BLEACH LED flashes, if programmed, when bleach can be added.

INSERT COINS/CARD LED

INSERT COINS/CARD LED prompts the user for coins or a card to satisfy the vend price. Four digits and decimal point show the vend price remaining to be satisfied. The vend price displayed will decrease with each coin inserted. If a new wash temp is selected during the first fill of the wash cycle and it requires additional vend, the INSERT COINS/CARD light will flash one (1) second on and one (1) second off, and the display will show the vend price remaining to be satisfied.

REMOVE CARD LED (Card Models Only)

REMOVE CARD LED flashes one (1) second on and one (1) second off after the START pad has been pressed and the vend has been deducted from the card. It will also flash when a card is inserted and no vend amount is required.

CLOSE DOOR

CLOSE DOOR LED flashes one (1) second on and one (1) second off when the control is in the Start Mode and the door is open. It also flashes in the Ready Mode with the door open and a card has been inserted. Whenever the CLOSE DOOR LED flashes, the START LED is off.

Four 7-Segment Digits

The 7-SEGMENT DIGITS are used to display the time remaining in a cycle, vend price, error messages and descriptive codes. When displaying the time remaining, the colon will flash, and when displaying the vend price the decimal point may be lit. During diagnostic testing or manual programming of the control, these digits will display descriptive codes and values (as described in Entering the Manual Mode).

F232151

Page 14

Notes

F232151

Page 15

Washer-Extractor Operation

Start Up

When power is applied to the washer, the control will display INSERT COINS/CARD, the decimal point and the vend price. The INSERT COINS/CARD light will remain lit until the vend price has been satisfied. The default cycle setting is PERM PRESS, the default wash water fill temperature is WARM and the default rinse water temperature is COLD. The LEDs will be lit on PERM PRESS and WARM at the start of the cycle. Refer to Figure 2. These default settings are owner programmable. Refer to Programming NetMaster.

Ready Mode

When a cycle is complete, the control will display “:00” until the washer-extractor door is opened, a key is pressed or a coin/card is entered. When one of these three options occurs, the display will revert back to the Ready Mode. Refer to Figure 2.

Cycle Sequence

Upon the start of a cycle, NetMaster will display the total cycle time. The appropriate LEDs will light while the machine passes through different cycle steps. Any coin entered after the first fill/tumble cycle will be added to the total coin counter, but the user will not be able to change cycles or water temperature.

Closing Washer-Extractor Door

If the door is not closed when the START pad is pressed, “door” will be displayed until the door is closed. Once door is closed, the START pad must be pressed again to lock door and start the cycle. If the door does not lock within 15 seconds of being closed, “E:dL” will be displayed indicating a door lock error and the machine will shut off.

C872I

Figure 2

To start the cycle, the user must press the START keypad after the vend price has been satisfied.

The user will be able to select a different cycle or wash water temperature by pressing a cycle pad when the machine is in the Ready Mode or in the first fill cycle. If not enough vend is entered to satisfy the vend price, the control will display the remaining vend price needed to start the cycle. If the first fill was interrupted to change the temperature (which requires more money), and the vend price is not satisfied within one minute, the washer control will go back to the first selection and the cycle will restart. After the first fill, all key presses will be ignored, allowing the washer to go through the complete cycle.

F232151

Page 16

Washer-Extractor Operation

Signals

There are four options when a signal can be used during the washer-extractor operation. These four options are listed below:

1. End of Cycle Signal By default, this signal is turned off. If turned on, the signal sounds for three (3) seconds at the end of a cycle.

2. Signal On Keypad Depression By default, this signal is turned on and sounds for a quarter of a second each time a keypad is pressed.

3. Signal On Coin Input/Card Insertion By default, this signal is turned on and will sound for a quarter of a second each time a coin or card is entered.

4. Signal for Card Removal (Card Models Only) By default, this signal is turned on and will sound one second on and one second off when the REMOVE CARD LED is flashing.

NOTE: Refer to Programming NetMaster to program signal options.

Changing Cycles

Cycles and wash temperatures can be changed anytime during the first fill/tumble cycle. After the first fill/ tumble cycle, all key presses are ignored.

Selecting a higher priced wash temperature will stop the first fill/tumble cycle, and INSERT COINS/CARD will flash one (1) second on and one (1) second off until the vend price has been satisfied. After the vend price has been satisfied, the cycle will restart with the new wash temperature. If the vend price is not satisfied within one minute, the control will go back to the previously set wash temperature.

F232151

Page 17

NetMaster Special Features

Programming NetMaster

NetMaster allows the washer-extractor owner to program the control with the use of the keypad. Audit, diagnostic, cycle and vend information may be programmed and retrieved by pressing combinations of the Select Cycle and Select Wash Temp pads.

For details on programming cycle and vend information, refer to Programming NetMaster.

Collecting Audit Information

The control will store audit information in its memory that can be retrieved by pressing various combinations of Select Cycle and Select Wash Temp pads. NetMaster will record coins entered, total wash cycles and total start pulses.

For more information on the audit features, refer to Collecting Audit Information.

NOTE: Additional audit information is retrievable with the Micro-Wand IIIE, the Card Reader or the Network. Refer to the appropriate instruction manual.

Testing Machine and NetMaster Functions

Special programmable diagnostic features built into NetMaster allow the owner to run specific diagnostic tests. By opening and closing the service door and then pressing various sequences of Select Cycle and Select Wash Temp pads, the owner may perform the following tests:

● Control Software Version Number

● Heater on Test

● Access Panel Opening Test

● Coin Vault Opening Test

● Coin Drop #1 Input Test

● Coin Drop #2 Input Test

● Door Switch Input Test

● Door Lock Switch Input Test

● Show Fill Time Test

● Show Drain Time Test

● Temperature Sensor Display Test

● Start Pulse Test

● Pressure Switches Opening Test

● Configuration #1 Display Test

● Configuration #2 Display Test

● Configuration #3 Display Test

● VFD Balance Input Test

● VFD Filter Input Test

● Water Purge

For detailed information on running diagnostic tests, refer to Testing Machine and NetMaster Functions.

Sales Floor Feature

NetMaster washer-extractor has a built-in sales floor routine used to display all LED lights and the four digits with the colon and decimal point. This function is designed to show potential customers the high-tech features of NetMaster.

For detailed information, refer to Sales Floor Feature.

Rapid Advance Feature

This feature allows the user to quickly advance through active cycles or advance into a cycle from the Ready Mode. This feature is useful when tests must be performed immediately on a washer-extractor currently in an active cycle. In this case, the user can quickly advance through the cycles to the Ready Mode. At this point, the user can perform the required tests and then return the washer-extractor to the point it was interrupted.

For detailed information, refer to Rapid Advance Fea tu re .

Clearing the NetMaster Vend Feature

This feature allows the user to return NetMaster back to the Ready Mode if coins or a card have been entered but the full vend price has not yet been satisfied. Refer to Figure 2.

For more information, refer to Clear Vend Feature.

Communications Mode

This feature allows the washer-extractor control to communicate with the Micro-Wand IIIE, the Card Reader or the Network. This allows the washerextractor control to be programmed and have its data read without using the keypad.

For more detailed information, refer to Communications Mode.

Dual Coin Drop

The control will accept pulses from a single or dual coin drop to satisfy vend price. Each coin drop will have the ability to start or run a cycle.

F232151

Page 18

NetMaster Special Features

Start Pulse Operation

The control will accept pulses from a central card reader system. The machine can be programmed to receive a single start pulse or multiple start pulses, or the Start Pulse Option can be turned off. The Start Pulse Mode allows the machine to go from the Ready Mode to the Start mode after a single pulse or multiple pulses are received. For details on programming Start Pulse Operation, refer to Programming NetMaster in the Enhanced Programming Guide, available at extra cost.

Access Panel and Coin Vault Openings

The control will capture the times and dates of the openings of the Coin Vault and the Access Panel. The information is saved in memory. An open access panel combined with various keypad presses allows the control to enter manual modes of operation if the Break-In Alarm is not on. These modes include Manual Programming, Audit Collection and Diagnostics.

Break-In Alarm

This feature allows the owner to program the machine to signal an alarm if the access panel or coin vault is opened without disabling the alarm first. The date and time of the break-in is recorded.

Lucky Cycle

This feature allows the owner to program the machine to provide a free vend cycle to customers after a certain number of cycles have occurred.

For details on programming the Lucky Cycle Option, refer to Programming NetMaster.

Site Code Pricing

This feature allows owners to program the control to accept site codes for special vending that are specific to select groups or individuals when using cards.

For details on programming the site code options, refer to Programming NetMaster in the Enhanced Programming Guide, available at extra cost.

Special Cycle

This feature allows the owner to offer extra features to customers for an added vend price. Features available include extra wash time, extra Rinse Extra time, warm water (used in the rinse final fill step) and Very High Speed Final Extract (on VFD models).

For details on programming the Special Cycle option, refer to Programming NetMaster in the Enhanced Programming Guide, available at extra cost.

Auto-Flush Feature

Special Vend

This feature allows the owner to program the control to allow programmable vend prices for specific hours and dates.

For details on programming Special Vend, refer to Programming NetMaster.

This feature, if enabled, allows the control to be set to automatically flush the dispenser compartments at predetermined intervals and times. The control will flush the dispenser compartments with hot water for a pre-programmed number of seconds or until a low water level is reached.

F232151

Page 19

Opening the Access Panel

To manually program NetMaster, the access panel must be opened. Opening and closing the access panel trips a switch which allows access to various programming options. Once opened, the access panel may either be left open, and then closed after programming, or it may be closed immediately.

NOTE: If the Break-In Alarm option is enabled, it must be disabled before opening the access panel. For more information on using the Break-In Alarm, refer to the Micro-Wand IIIE or Network Instruction Manual.

The access panel is located on the top of the washerextractor. Refer to Fig ure 3.

After opening, or opening and closing the access panel, the operator has 4.25 minutes to begin programming. If the appropriate SELECT PADS have not been pressed in that time, the control will not accept operator programming. Should this happen, opening and closing the access panel will once again trip the switch which allows access to the programming options.

1 Access Panel Lock 2 Access Panel

F232151

Figure 3

C873I

Page 20

Notes

F232151

Page 21

Entering the Manual Mode

neednew#1

For programming, testing and retrieving information from NetMaster, it is often necessary to enter the Manual Mode by following the four simple steps below.

How to Enter the Manual Mode

1. Be sure the washer-extractor is in the Ready Mode before continuing to step 2. Refer to Figure 2. If the washer-extractor is in an active cycle, rapid advance through the cycle. Refer to Rapid Advance Feature. If coins have been entered, refer to Clear Vend Feature.

2. Open the access panel. Refer to Opening the Access Panel.

3. While pressing and holding the NORMAL keypad with one hand, press the HOT keypad with the other hand.

4. The VFD display will show “rAPd”. Refer to

Figure 4.

Manual Mode is broken into two groups: Manual Programming and Manual Rapid Advance/Diagnostics. Manual Programming can only be turned ON or OFF with the Micro-Wand IIIE, the Smart Card Reader or the Network. Refer to the appropriate instruction manual. Manual Rapid Advance/Diagnostics can be turned ON and OFF using the Micro-Wand IIIE, by manual programming (refer to option 81 in Programming NetMaster), with the Smart Card Reader, or with the Network.

By default, both groups are turned ON.

The manual features available in each group are as follows (the menu displayed on the VFD in this mode is in parentheses).

Manual Programming

Manual Programming (PrOg)

Manual Read Audit (AudT)

Manual Reset (rSET)

Rapid Advance/Diagnostics

Rapid Advance (rAPd)

Figure 4

5. Press the DELICATES (+) or the COLD (-) keypad to scroll through the options until the desired option appears in the VFD.

6. Press the START (enter) keypad.

B30R

Show Mode (SHOW)

Diagnostic Tests (dIAg)

If a group is turned OFF, the feature menu will still appear, but the features in the group cannot be entered.

NOTE: If no feature is chosen, the washerextractor will return to the Ready Mode after approximately four minutes.

F232151

Page 22

Notes

F232151

Page 23

Programming NetMaster

What Can Be Programmed?

This feature allows the owner to program cycle information, standard vend pricing, special vends and other features by using the keypads. The control must have the Manual Programming Mode enabled, which is the factory default. This mode can only be turned OFF and ON by using the Micro-Wand IIIE, the Smart Card Reader or the Network. Refer to this section when programming NetMaster.

This section offers a detailed description of basic options available to program. Additional options can be found in the Enhanced Programming Guide, available at extra cost.

Each description includes instructions on when and why the option might be used and, more importantly, how to program the option.

For more advanced users, refer to Table 1 for a quick reference list of the options available through the programming mode.

NOTE: The three numbers in the Option column of Table 1 are what will be shown in the VFD display when that option is selected.

F232151

Page 24

Programming NetMaster

Programmable Options Available

OPTION DESCRIPTION

001 Audio Signal

002 Regular Hot Wash Vend Price

003 Regular Warm Wash Vend Price

004 Regular Cold Wash Vend Price

005 Special Wash Hot Wash Vend Price

006 Special Wash War m Wa s h Vend P ric e

007 Special Wash Cold Wash Vend Price

014 Special Cycle Vend Price

015 Special Vend A Days Enable

016 Special Vend A Start Hour

017 Special Vend A Length in Hours

018 Special Vend A Start Month

019 Special Vend A Start Date

020 Special Vend A End Month

021 Special Vend A End Date

023 Special Vend A Regular Hot Wash Vend Price

024 Special Vend A Regular Warm Wash Vend

Price

025 Special Vend A Regular Cold Wash Vend

Price

026 Special Vend A Special Wash Hot Wash Vend

Price

027 Special Vend A Special Wash Warm Wash

Ven d P r ic e

028 Special Vend A Special Wash Cold Wash

Ven d P r ic e

029 Special Vend A Auto-Shutdown Enable

030 Coin #1 Value

031 Coin #2 Value

033 Default Cycle/Temperature

035 Set Real-Time Clock Minutes

036 Set Real-Time Clock Hours

OPTION DESCRIPTION

037 Set Real-Time Clock Day

038 Set Real-Time Clock Date

039 Set Real-Time Clock Month

040 Set Real-Time Clock Year

041 Set Real-Time Clock Century

042 Normal PreWash #1 Fill/Tumble Time

044 Normal Wash Fill/Tumble Time

045 Normal Rinse #1 Fill/Tumble Time

047 Normal Rinse Final Fill/Tumble Time

048 Normal Spin Extract Time

051 Permanent Press PreWash #1 Fill/Tumble

Time

053 Permanent Press Wash Fill/Tumble Time

054 Permanent Press Rinse #1 Fill/Tumble Time

056 Permanent Press Rinse Final Fill/Tumble

Time

057 Permanent Press Spin Extract Time

062 Delicates Wash Fill/Tumble Time

063 Delicates Rinse #1 Fill/Tumble Time

065 Delicates Rinse Final Fill/Tumble Time

066 Delicates Spin Extract Time

069 Special Wash PreWash #1 Fill/Tumble Time

071 Special Wash Wash Fill/Tumble Time

072 Special Wash Rinse #1 Fill/Tumble Time

074 Special Wash Rinse Final Fill/Tumble Time

075 Special Wash Spin Extract

081 Control Configuration Data #1

114 Lucky Option

118 Auto-Flush Option

119 Auto-Flush Hour

120 Auto-Flush DOW

121 Smart Card Maximum Value

Table 1

F232151

Page 25

Additional options found in the Enhanced Programming Guide (available at extra cost) include:

● Site Code #1

● Site Code #1 Regular (Hot, Warm and Cold

Wash) Vend Prices

● Site Code #1 Special Wash (Hot, Warm and Cold

Wash) Vend Prices

● Special Vend A Site Code #1

● Start Pulse Value

● Power Fail Reset

● Normal, Permanent Press, Delicates and Special

Wash PreWash #2 Fill/Tumble Times

● Normal, Permanent Press, Delicates and Special

Wash Rinse Extra Fill/Tumble Times

● Normal, Permanent Press, Delicates and Special

Wash Spin Extract Speeds

● Normal, Permanent Press, Delicates and Special

Wash Extracts On/Off

● Delicates PreWash #1 Fill/Tumble Time

● PreWash #1/PreWash #2/Rinses Water

Temperature

● Fill/Tumble Water Levels #1 and #2

● Configuration Data #2 and #3

● Hot, Warm and Cold Water Temperatures

● Dispenser and Drain Options

● Water Inlet

● Special Cycle Option and Times

● Error Code Programming Parameter

● Start Pulse Mode

Programming NetMaster

F232151

Page 26

Programming NetMaster

1. Audio Signal “+001”

This option allows the owner to program when the signal will sound.

There are four occasions when a signal may sound during the washer operation. These four occasions are listed below:

C821I

1. End of Cycle Signal By default, the signal is turned off. If turned on, the signal will sound for three seconds at the end of a cycle.

2. Keypad Depression Signal By default, this signal is turned on and will sound for a quarter of a second. This signal will sound each time a keypad is pressed.

3. Coin Input/Card Insertion Signal By default, this signal is turned on and will sound for a quarter of a second each time a coin or card is entered.

4. Remove Card Signal (Card Models Only) By default, this signal is turned on and will sound one (1) second on and one (1) second off when the REMOVE CARD LED is flashing and the transaction is complete.

How to Program the Audio Signal

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad.

Figure 6

4. Locate the desired number in the first column of Table 2 on the following page.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number until correct. Refer to Figure 7.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

Figure 5

3. “+001” will appear in the VFD. Press the START

(enter) keypad. A number will appear in the VFD. This number corresponds to the current Audio Signal Programming Value. Refer to Figure 6.

Figure 7

Example: An owner might wish to have the signal sound only when a keypad is pressed. Entering the number “1” in step 5 would turn off all the options except KEYPAD. In this instance, the signal would sound only when a keypad is pressed.

C762I

6. Press the START (enter) keypad when the correct number appears in the VFD. The next option, “+002”, will appear in the VFD.

NOTE: To program “+002” (Regular Hot Wash Vend Price), refer to option 2. To program other options, refer to the appropriate section.

F232151

Page 27

Programming NetMaster

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

How to Read Table 2

To determine the correct number required to program the Audio Signal, use the following table. The Signal Value column contains the number required in step 5. The other columns correspond to individual options.

Each column of options contains a unique combination of the words ON and OFF that indicates if that column’s option is turned on or off when the Signal Value is entered. Select the desired combination of options and enter the number found in the Signal Value column.

Signal

Value

10 ON OFF ON OFF

11 ON OFF ON ON

12 ON ON OFF OFF

13 ON ON OFF ON

Remove

Card

0 OFF OFF OFF OFF

1 OFF OFF OFF ON

2OFFOFFON OFF

3OFFOFFON ON

4OFFON OFF OFF

5OFFON OFF ON

6OFFON ON OFF

7OFFON ON ON

8 ON OFF OFF OFF

9 ON OFF OFF ON

Coin/Card

Input

End of

Cycle

Key

Pressed

14 ON ON ON OFF

15 ON ON ON ON

Table 2

F232151

Page 28

Programming NetMaster

2. Regular Hot Wash Vend Price “+002”

This option allows the owner to set the vend price for a hot wash for all Regular Wash cycles (Normal, Permanent Press and Delicates). This vend price will be displayed in the VFD when HOT is selected.

How to Program the Regular Hot Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

4. When “+002” appears in the VFD, press the

START (enter) keypad. There are five digits in the Regular Hot Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 10.

C826I

Figure 10

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 11.

NOTE: The vend price can be set from 1 to 65,535.

C762I

Figure 8

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until

“+002” appears in the VFD. Refer to Figure 9.

C764I

Figure 9

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 11

neednew#2

B029R

F232151

Page 29

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 12.

C827I

Figure 12

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+003”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+003” (R eg u l a r Wa r m Was h Vend Price), refer to option 3. To program other options, refer to the appropriate section.

F232151

Page 30

Programming NetMaster

3. Regular Warm Wash Vend Price “+003”

This option allows the owner to set the vend price for a warm wash for all Regular Wash cycles (Normal, Permanent Press and Delicates). This vend price will be displayed in the VFD when WARM is selected.

How to Program the Regular Warm Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

4. When “+003” appears in the VFD, press the

START (enter) keypad. There are five digits in the Regular Warm Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 15.

C826I

Figure 15

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 16.

NOTE: The vend price can be set from 1 to 65,535.

Figure 13

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+003” appears in the VFD. Refer to Figure 14.

Figure 14

C762I

C765I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 16

neednew#2

B029R

F232151

Page 31

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 17.

C827I

Figure 17

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+004”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+004” (Regular Cold Wash Vend Price), refer to option 4. To program other options, refer to the appropriate section.

F232151

Page 32

Programming NetMaster

4. Regular Cold Wash Vend Price “+004”

This option allows the owner to set the vend price for a cold wash for all Regular Wash cycles (Normal, Permanent Press and Delicates). This vend price will be displayed in the VFD when COLD is selected.

How to Program the Regular Cold Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

4. When “+004” appears in the VFD, press the

START (enter) keypad. There are five digits in the Regular Cold Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 20.

C826I

Figure 20

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 21.

NOTE: The vend price can be set from 1 to 65,535.

Figure 18

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+004” appears in the VFD. Refer to Figure 19.

Figure 19

C762I

C766I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 21

neednew#2

B029R

F232151

Page 33

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 22.

C827I

Figure 22

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+005”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+005” (Special Wash Hot Wash Vend Price), refer to option 5. To program other options, refer to the appropriate section.

F232151

Page 34

Programming NetMaster

5. Special Wash Hot Wash Vend Price “+005”

This option allows the owner to set the vend price for a hot wash for the Special Wash cycle. This vend price will be displayed in the VFD when HOT is selected.

How to Program the Special Wash Hot Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

4. When “+005” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Wash Hot Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 25.

C826I

Figure 25

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 26.

NOTE: The vend price can be set from 1 to 65,535.

C762I

Figure 23

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until

“+005” appears in the VFD. Refer to Figure 24.

C835I

Figure 24

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 26

neednew#2

B029R

F232151

Page 35

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 27.

C827I

Figure 27

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+006”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+006” (Special Wash Warm Wash Vend Price), refer to option 6. To program other options, refer to the appropriate section.

F232151

Page 36

Programming NetMaster

6. Special Wash Warm Wash Vend Price “+006”

This option allows the owner to set the vend price for a warm wash for the special wash cycle. This vend price will be displayed in the VFD when WARM is selected.

How to Program the Special Wash Warm Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+006” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Wash Warm Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 30.

C826I

Figure 30

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 31.

NOTE: The vend price can be set from 1 to 65,535.

Figure 28

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+006” appears in the VFD. Refer to Figure 29.

C836I

Figure 29

C836I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 31

neednew#2

B029R

F232151

Page 37

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 32.

C827I

Figure 32

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+007”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+007” (Special Wash Cold Wash Vend Price), refer to option 7. To program other options, refer to the appropriate section.

F232151

Page 38

Programming NetMaster

7. Special Wash Cold Wash Vend Price “+007”

This option allows the owner to set the vend price for a cold wash for the special wash cycle. This vend price will be displayed in the VFD when COLD is selected.

How to Program the Special Wash Cold Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+007” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Wash Cold Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on, one second off. Refer to Figure 35.

C826I

Figure 35

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 36.

NOTE: The vend price can be set from 1 to 65,535.

Figure 33

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+007” appears in the VFD. Refer to Figure 34.

C837I

Figure 34

C837I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 36

neednew#2

B029R

F232151

Page 39

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 37.

C827I

Figure 37

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+008”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+008” (Site Code #1 Regular Hot Wash Vend Price), refer to option 8 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

F232151

Page 40

Programming NetMaster

15. Special Vend A Days Enable “+015”

This option allows the owner to set the day or days of a special vend.

Special Vend A is used to change the standard vend prices for special occasions or to turn the machine off. The special vend can be programmed to start and end on a specific day or days of the week.

The owner may also turn the Special Vend A option on or off if desired.

How to Program Special Vend A Days Enable

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

4. When “+015” appears in the VFD, press the

START (enter) keypad. A number will appear in the VFD that corresponds to the current Special Vend A Days Enable Programming Value.

5. Locate the desired number in the first column of Table 3 on the following pages.

6. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number until correct. Refer to Figure 40.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

Figure 38

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+015” appears in the VFD. Refer to Figure 39.

Figure 39

C762I

C777I

Figure 40

7. Press the START (enter) keypad when the correct number appears in the VFD. The next option, “+016”, will appear in the VFD.

NOTE: To program “+016” (Special Vend A Start Hour), refer to option 16. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 41

How to Read

Programming NetMaster

To determine the correct number required to program the Special Vend A Days Enable, use the following table. The “SPA” Value column contains the number required in step 6. The other columns correspond to individual days.

Each column of days contains a unique combination of the words ON and OFF that indicates if that column’s day is turned on or off when the “SPA” value is entered. Select the desired combination of days and enter the number found in the “SPA” value column.

“+015”

“SPA” VALUE SAT FRI THUR WED TUE MON SUN ON/OFF

0 OFF OFF OFF OFF OFF OFF OFF OFF

3 OFF OFF OFF OFF OFF OFF ON ON

5 OFF OFF OFF OFF OFF ON OFF ON

7 OFF OFF OFF OFF OFF ON ON ON

9 OFF OFF OFF OFF ON OFF OFF ON

11 OFF OFF OFF OFF ON OFF ON ON

13 OFF OFF OFF OFF ON ON OFF ON

15 OFF OFF OFF OFF ON ON ON ON

17 OFF OFF OFF ON OFF OFF OFF ON

19 OFF OFF OFF ON OFF OFF ON ON

21 OFF OFF OFF ON OFF ON OFF ON

23 OFF OFF OFF ON OFF ON ON ON

25 OFF OFF OFF ON ON OFF OFF ON

27 OFF OFF OFF ON ON OFF ON ON

29 OFF OFF OFF ON ON ON OFF ON

31 OFF OFF OFF ON ON ON ON ON

33 OFF OFF ON OFF OFF OFF OFF ON

35 OFF OFF ON OFF OFF OFF ON ON

37 OFF OFF ON OFF OFF ON OFF ON

39 OFF OFF ON OFF OFF ON ON ON

41 OFF OFF ON OFF ON OFF OFF ON

43 OFF OFF ON OFF ON OFF ON ON

45 OFF OFF ON OFF ON ON OFF ON

47 OFF OFF ON OFF ON ON ON ON

49 OFF OFF ON ON OFF OFF OFF ON

51 OFF OFF ON ON OFF OFF ON ON

53 OFF OFF ON ON OFF ON OFF ON

55 OFF OFF ON ON OFF ON ON ON

57 OFF OFF ON ON ON OFF OFF ON

59 OFF OFF ON ON ON OFF ON ON

61 OFF OFF ON ON ON ON OFF ON

63 OFF OFF ON ON ON ON ON ON

65 OFF ON OFF OFF OFF OFF OFF ON

67 OFF ON OFF OFF OFF OFF ON ON

69 OFF ON OFF OFF OFF ON OFF ON 71 OFF ON OFF OFF OFF ON ON ON

Table 3 (Continued)

)(

F232151

Page 42

Programming NetMaster

Table 3 (Continued)

“+015”

“SPA” VALUE SAT FRI THUR WED TUE MON SUN ON/OFF

73 OFF ON OFF OFF ON OFF OFF ON 75 OFF ON OFF OFF ON OFF ON ON 77 OFF ON OFF OFF ON ON OFF ON 79 OFF ON OFF OFF ON ON ON ON 81 OFF ON OFF ON OFF OFF OFF ON 83 OFF ON OFF ON OFF OFF ON ON 85 OFF ON OFF ON OFF ON OFF ON 87 OFF ON OFF ON OFF ON ON ON 89 OFF ON OFF ON ON OFF OFF ON 91 OFF ON OFF ON ON OFF ON ON 93 OFF ON OFF ON ON ON OFF ON 95 OFF ON OFF ON ON ON ON ON 97 OFF ON ON OFF OFF OFF OFF ON

99 OFF ON ON OFF OFF OFF ON ON 101 OFF ON ON OFF OFF ON OFF ON 103 OFF ON ON OFF OFF ON ON ON 105 OFF ON ON OFF ON OFF OFF ON 107 OFF ON ON OFF ON OFF ON ON 109 OFF ON ON OFF ON ON OFF ON 111 OFF ON ON OFF ON ON ON ON 113 OFF ON ON ON OFF OFF OFF ON 115 OFF ON ON ON OFF OFF ON ON 117 OFF ON ON ON OFF ON OFF ON 119 OFF ON ON ON OFF ON ON ON 121 OFF ON ON ON ON OFF OFF ON 123 OFF ON ON ON ON OFF ON ON 125 OFF ON ON ON ON ON OFF ON 127 OFF ON ON ON ON ON ON ON 129 ON OFF OFF OFF OFF OFF OFF ON 131 ON OFF OFF OFF OFF OFF ON ON 133 ON OFF OFF OFF OFF ON OFF ON 135 ON OFF OFF OFF OFF ON ON ON 137 ON OFF OFF OFF ON OFF OFF ON 139 ON OFF OFF OFF ON OFF ON ON 141 ON OFF OFF OFF ON ON OFF ON 143 ON OFF OFF OFF ON ON ON ON 145 ON OFF OFF ON OFF OFF OFF ON 147 ON OFF OFF ON OFF OFF ON ON 149 ON OFF OFF ON OFF ON OFF ON 151 ON OFF OFF ON OFF ON ON ON 153 ON OFF OFF ON ON OFF OFF ON 155 ON OFF OFF ON ON OFF ON ON 157 ON OFF OFF ON ON ON OFF ON 159 ON OFF OFF ON ON ON ON ON 161 ON OFF ON OFF OFF OFF OFF ON 163 ON OFF ON OFF OFF OFF ON ON

Table 3 (Continued)

F232151

Page 43

Programming NetMaster

Table 3 (Continued)

“+015”

“SPA” VALUE SAT FRI THUR WED TUE MON SUN ON/OFF

165 ON OFF ON OFF OFF ON OFF ON 167 ON OFF ON OFF OFF ON ON ON 169 ON OFF ON OFF ON OFF OFF ON 171 ON OFF ON OFF ON OFF ON ON 173 ON OFF ON OFF ON ON OFF ON 175 ON OFF ON OFF ON ON ON ON 177 ON OFF ON ON OFF OFF OFF ON 179 ON OFF ON ON OFF OFF ON ON 181 ON OFF ON ON OFF ON OFF ON 183 ON OFF ON ON OFF ON ON ON 185 ON OFF ON ON ON OFF OFF ON 187 ON OFF ON ON ON OFF ON ON 189 ON OFF ON ON ON ON OFF ON 191 ON OFF ON ON ON ON ON ON 193 ON ON OFF OFF OFF OFF OFF ON 195 ON ON OFF OFF OFF OFF ON ON 197 ON ON OFF OFF OFF ON OFF ON 199 ON ON OFF OFF OFF ON ON ON 201 ON ON OFF OFF ON OFF OFF ON 203 ON ON OFF OFF ON OFF ON ON 205 ON ON OFF OFF ON ON OFF ON 207 ON ON OFF OFF ON ON ON ON 209 ON ON OFF ON OFF OFF OFF ON 211 ON ON OFF ON OFF OFF ON ON 213 ON ON OFF ON OFF ON OFF ON 215 ON ON OFF ON OFF ON ON ON 217 ON ON OFF ON ON OFF OFF ON 219 ON ON OFF ON ON OFF ON ON 221 ON ON OFF ON ON ON OFF ON 223 ON ON OFF ON ON ON ON ON 225 ON ON ON OFF OFF OFF OFF ON 227 ON ON ON OFF OFF OFF ON ON 229 ON ON ON OFF OFF ON OFF ON 231 ON ON ON OFF OFF ON ON ON 233 ON ON ON OFF ON OFF OFF ON 235 ON ON ON OFF ON OFF ON ON 237 ON ON ON OFF ON ON OFF ON 239 ON ON ON OFF ON ON ON ON 241 ON ON ON ON OFF OFF OFF ON 243 ON ON ON ON OFF OFF ON ON 245 ON ON ON ON OFF ON OFF ON 247 ON ON ON ON OFF ON ON ON 249 ON ON ON ON ON OFF OFF ON 251 ON ON ON ON ON OFF ON ON 253 ON ON ON ON ON ON OFF ON 255 ON ON ON ON ON ON ON ON

F232151

Page 44

Programming NetMaster

C838I

16. Special Vend A Start Hour “+016”

This option allows the owner to set the hour that Special Vend A will begin.

How to Program Special Vend A Hour

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 41

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+016” appears in the VFD. Refer to Figure 42.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the start hour to the desired hour. Refer to Figure 43.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 43

neednew#2

B029R

6. Press the START (enter) keypad when the correct hour appears in the VFD. The next option, “+017”, will appear in the VFD.

NOTE: To program “+017” (Special Vend A Length in Hours), refer to option 17. To program other options, refer to the appropriate section.

Figure 42

4. When “+016” appears in the VFD, press the

START (enter) keypad. The current start time (in military time) will appear in the VFD.

C838I

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 45

Programming NetMaster

17. Special Vend A Length in Hours “+017”

This option allows the owner to set the length in hours for Special Vend A.

How to Program Special Vend A Length in Hours

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 44

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+017” appears in the VFD. Refer to Figure 45.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current length of hours to the desired number of hours. Refer to Figure 46.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 46

neednew#2

B029R

6. Press the START (enter) keypad when the correct hour appears in the VFD. The next option, “+018”, will appear in the VFD.

NOTE: To program “+018” (Special Vend A Start Month), refer to option 18. To program other options, refer to the appropriate section.

Figure 45

4. When “+017” appears in the VFD, press the

START (enter) keypad. The current length in hours will appear in the VFD.

C795I

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 46

Programming NetMaster

18. Special Vend A Start Month “+018”

This option allows the owner to set the month that Special Vend A will begin.

NOTE: If Special Vend A Start Month, Start Date, End Month, or End Date are programmed to zero (default is zero), the special Vend A will be active every week on the days programmed in option 15.

How to Program Special Vend A Start Month

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the start month to the desired month. Refer to Figure 49.

If “0” is selected and Special Vend A is on, Special Vend A will occur at the time and days of week selected, regardless of the month.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

Figure 47

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+018” appears in the VFD. Refer to Figure 48.

Figure 48

4. When “+018” appears in the VFD, press the START (enter) keypad. The current start month will appear in the VFD.

C762I

C794I

Figure 49

6. Press the START (enter) keypad when the correct month appears in the VFD. The next option, “+019”, will appear in the VFD.

NOTE: To program “+019” (Special Vend A Start Date), refer to option 19. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

1. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 47

Programming NetMaster

19. Special Vend A Start Date “+019”

This option allows the owner to set the date that Special Vend A will begin.

How to Program Special Vend A Start Date

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 50

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+019” appears in the VFD. Refer to Figure 51.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the start date to the desired date. Refer to Figure 52.

If “0” is selected and Special Vend A is on, Special Vend A will occur at the time or days of week selected, regardless of the date.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 52

neednew#2

B029R

6. Press the START (enter) keypad when the correct date appears in the VFD. The next option, “+020”, will appear in the VFD.

Figure 51

4. When “+019” appears in the VFD, press the

START (enter) keypad. The current start date will appear in the VFD.

C793I

NOTE: To program “+020” (Special Vend A End Month), refer to option 20. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 48

Programming NetMaster

20. Special Vend A End Month “+020”

This option allows the owner to set the month that Special Vend A will end.

How to Program Special Vend A End Month

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 53

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+020” appears in the VFD. Refer to Figure 54.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the end month to the desired month. Refer to Figure 55.

If “0” is selected and Special Vend A is on, Special Vend A will occur at the time or day of week selected, regardless of the month.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 55

neednew#2

B029R

6. Press the START (enter) keypad when the correct month appears in the VFD. The next option,

“+021”, will appear in the VFD.

Figure 54

4. When “+020” appears in the VFD, press the

START (enter) keypad. The current end month will appear in the VFD.

C792I

NOTE: To program “+021” (Special Vend A End Date), refer to option 21. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 49

Programming NetMaster

21. Special Vend A End Date “+021”

This option allows the owner to set the date that Special Vend A will end.

How to Program Special Vend A End Date

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 56

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+021” appears in the VFD. Refer to Figure 57.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the end date to the desired date. Refer to Figure 58.

If “0” is selected and Special Vend A is on, Special Vend A will occur at the time or days of week selected, regardless of the date.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 58

neednew#2

B029R

6. Press the START (enter) keypad when the correct date appears in the VFD. The next option, “+022”, will appear in the VFD.

Figure 57

4. When “+021” appears in the VFD, press the

START (enter) keypad. The current end date will appear in the VFD.

C791I

NOTE: To program “+022” (Special Vend A Site Code #1), refer to option 22 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 50

Programming NetMaster

C789I

23. Special Vend A Regular Hot Wash Vend Price “+023”

This option allows the owner to set the vend price for a Hot Wash in all regular cycles (Normal, Permanent Press and Delicates) in Special Vend A.

How to Program Special Vend A Regular Hot Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+023” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Vend A Regular Hot Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 61.

C826I

Figure 61

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 62.

NOTE: The vend price can be set from 0 to 65,535.

Figure 59

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+023” appears in the VFD. Refer to Figure 60.

Figure 60

C789I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 62

neednew#2

B029R

F232151

Page 51

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 63.

C828I

Figure 63

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+024”, will appear in the VFD.

NOTE: To program “+024” (Special Vend A Regular Warm Wash Vend Price), refer to option

24. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 52

Programming NetMaster

24. Special Vend A Regular Warm Wash Vend Price “+024”

This option allows the owner to set the vend price for a Warm Wash in all regular cycles (Normal, Permanent Press and Delicates) in Special Vend A.

How to Program Special Vend A Regular Warm Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+024” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Vend A Regular Warm Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 66.

C826I

Figure 66

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 67.

NOTE: The vend price can be set from 0 to 65,535.

Figure 64

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+024” appears in the VFD. Refer to Figure 65.

Figure 65

C788I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 67

neednew#2

B029R

F232151

Page 53

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 68.

C828I

Figure 68

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+025”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+025” (Special Vend A Regular Cold Wash Vend Price), refer to option 25. To program other options, refer to the appropriate section.

F232151

Page 54

Programming NetMaster

25. Special Vend A Regular Cold Wash Vend Price “+025”

This option allows the owner to set the vend price for a Cold Wash in all regular cycles (Normal, Permanent Press and Delicates) in Special Vend A.

How to Program Special Vend A Regular Cold Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+025” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Vend A Regular Cold Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 71.

C826I

Figure 71

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 72.

NOTE: The vend price can be set from 0 to 65,535.

Figure 69

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+025” appears in the VFD. Refer to Figure 70.

Figure 70

C787I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 72

neednew#2

B029R

F232151

Page 55

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 73.

C828I

Figure 73

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+026”, will appear in the VFD.

NOTE: To program “+026” (Special Vend A Special Wash Hot Wash Vend Price), refer to option

26. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 56

Programming NetMaster

26. Special Vend A Special Wash Hot Wash Vend Price “+026”

This option allows the owner to set the vend price for a Hot Wash in the Special Wash cycle in Special Vend A.

How to Program Special Vend A Special Wash Hot Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+026” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Vend A Special Wash Hot Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 76.

C826I

Figure 76

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 77.

NOTE: The vend price can be set from 0 to 65,535.

Figure 74

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+026” appears in the VFD. Refer to Figure 75.

Figure 75

C786I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 77

neednew#2

B029R

F232151

Page 57

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 78.

C828I

Figure 78

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+027”, will appear in the VFD.

NOTE: To program “+027” (Special Vend A Special Wash Warm Wash Vend Price), refer to option 27. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 58

Programming NetMaster

27. Special Vend A Special Wash Warm Wash Vend Price “+027”

This option allows the owner to set the vend price for a Warm Wash in the Special Wash cycle in Special Vend A.

How to Program Special Vend A Special Wash Warm Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+027” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Vend A Special Wash Warm Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 81.

C826I

Figure 81

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 82.

NOTE: The vend price can be set from 0 to 65,535.

Figure 79

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+027” appears in the VFD. Refer to Figure 80.

Figure 80

C785I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 82

neednew#2

B029R

F232151

Page 59

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 83.

C828I

Figure 83

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+028”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+028” (Special Vend A Special Wash Cold Wash Vend Price), refer to option 28. To program other options, refer to the appropriate section.

F232151

Page 60

Programming NetMaster

28. Special Vend A Special Wash Cold Wash Vend Price “+028”

This option allows the owner to set the vend price for a Cold Wash in the Special Wash cycle in Special Vend A.

How to Program Special Vend A Special Wash Cold Wash Vend Price

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

4. When “+028” appears in the VFD, press the

START (enter) keypad. There are five digits in the Special Vend A Special Wash Cold Wash Vend Price. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 86.

C826I

Figure 86

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 87.

NOTE: The vend price can be set from 0 to 65,535.

Figure 84

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+028” appears in the VFD. Refer to Figure 85.

Figure 85

C784I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 87

neednew#2

B029R

F232151

Page 61

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 88.

C828I

Figure 88

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+029”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+029” (Special Vend A Auto-Shutdown Enable), refer to option 29. To program other options, refer to the appropriate section.

F232151

Page 62

Programming NetMaster

29. Special Vend A Auto-Shutdown Enable “+029”

This option, when turned on, will force the control to shutdown during the Programmed Special Vend A time period, preventing customers from starting a new cycle after a selected time. “OFF” is displayed on the VFD when Auto-Shutdown is active.

How to Program Special Vend A Auto-Shutdown Enable

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current value displayed in the VFD to the desired value. Refer to Figure 91.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 91

neednew#2

B029R

Figure 89

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+029” appears in the VFD. Refer to Figure 90.

Figure 90

4. When “+029” appears in the VFD, press the START (enter) keypad. The current Special Vend A Auto-Shutdown Enable parameter value will appear in the VFD. “0” will be displayed when Auto-Shutdown is disabled and “255” will be displayed when Auto-Shutdown is enabled.

C762I

C783I

6. Press the START (enter) keypad when the correct

value appears in the VFD. The next option, “+030”, will appear in the VFD.

NOTE: To program “+030” (Coin #1 Value), refer to option 30. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 63

Programming NetMaster

30. Coin #1 Value “+030”

This option allows the owner to set a specific numerical value for a coin entered. For example, in the United States, the coin value for one quarter would be measured in cents (25). Therefore, the coin value entered for one quarter would be 00025.

If the Regular Hot Wash Vend Price (option 2) is set for “.75”, and the Coin Value is set for “00025”, the vend price displayed will decrease by .25 for each coin entered.

How to Program Coin #1 Value

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

4. When “+030” appears in the VFD, press the

START (enter) keypad.There are five digits in the Coin #1 Value. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 94.

C826I

Figure 94

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 95.

NOTE: The coin value can be set from 1 to 65,535.

Figure 92

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+030” appears in the VFD. Refer to Figure 93.

Figure 93

C762I

C782I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 95

neednew#2

B029R

F232151

Page 64

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 96.

C829I

Figure 96

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+031”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+031” (Coin #2 Value), refer to option 31. To program other options, refer to the appropriate section.

F232151

Page 65

Programming NetMaster

31. Coin #2 Value “+031”

This option allows the owner to set a specific numerical value for a coin entered when using the dual coin drop. For example, the coin value for a dollar coin would be measured in cents (1.00). Therefore, the coin value entered for one dollar coin would be 00100.

If the Regular Hot Wash Vend Price (option 2) is set for “2.00”, and the Coin Value is set for “00100”, the vend price displayed will decrease by 1.00 for each dollar coin entered.

How to Program Coin #2 Value

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

4. When “+031” appears in the VFD, press the

START (enter) keypad. There are five digits in the Coin #2 Value. The fifth digit will appear in the VFD and will flash one second on and one second off. Refer to Figure 99.

C826I

Figure 99

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the fifth digit. Refer to Figure 100.

NOTE: The coin value can be set from 1 to 65,535.

Figure 97

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+031” appears in the VFD. Refer to Figure 98.

Figure 98

C762I

C781I

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 100

neednew#2

B029R

F232151

Page 66

Programming NetMaster

6. Press the START (enter) keypad to enter the fifth digit and display remaining four digits. The active digit will flash one second on and one second off. Refer to Figure 101.

C827I

Figure 101

7. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the value of the active digit and the START (enter) keypad to enter the value of the digit and advance to the next digit.

8. Press the START (enter) keypad with the last active digit. The next option, “+032”, will appear in the VFD.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

NOTE: To program “+032” (Start Pulse Value), refer to option 32 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

F232151

Page 67

Programming NetMaster

33. Default Cycle/Temperature “+033”

This option allows the owner to set the default cycle and temperature the machine will enter when in the Ready Mode. When programming the default cycle, refer to Table 4 on the following page.

How to Program Default Cycle/Temperature

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 102

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+033” appears in the VFD. Refer to Figure 103.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number to the desired number selected from Tab l e 4 on the following page. Refer to Figure 104.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 104

neednew#2

B029R

6. Press the START (enter) keypad when the correct number appears in the VFD. The next option, “+034”, will appear in the VFD.

NOTE: To program “+034” (Power Fail Reset), refer to option 34 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

Figure 103

4. When “+033” appears in the VFD, press the

START (enter) keypad. A number will appear in the VFD. This number corresponds to the current default cycle value.

F232151

C779I

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

Page 68

Programming NetMaster

How to Read Table 4

Refer to Ta b le 4 to determine the correct number required to program Default Cycle/Temperature. The Default Value column contains the number required in step 5. The other columns correspond to individual options.

Default

Value

9OFFOFFOFF ON OFF OFF ON

17 OFF OFF ON OFF OFF OFF ON

33 OFF ON OFF OFF OFF OFF ON

65 ON OFF OFF OFF OFF OFF ON

10 OFF OFF OFF ON OFF ON OFF

18 OFF OFF ON OFF OFF ON OFF

34 OFF ON OFF OFF OFF ON OFF

66 ON OFF OFF OFF OFF ON OFF

12 OFF OFF OFF ON ON OFF OFF

20 OFF OFF ON OFF ON OFF OFF

36 OFF ON OFF OFF ON OFF OFF

68 ON OFF OFF OFF ON OFF OFF

Normal

Cycle

Perm Press

Cycle

Delicates

Cycle

Each column of options contains a unique combination of the words ON and OFF that indicates if that column’s option is turned on or off when the Default Value is entered. Select the desired combination of options and enter the number found in the Default Value column.

“+033”

Special

Wash Cycle

Hot

Wash

Warm Wash

Cold

Wash

Ta b le 4

F232151

Page 69

Programming NetMaster

35. Set Real-Time Clock Minutes “+035”

This option allows the owner to set NetMaster’s internal clock to the correct time in minutes.

How to Program the Clock Minutes

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 105

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+035” appears in the VFD. Refer to Figure 106.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the minutes to the correct time. Refer to Figure 107.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 107

neednew#2

B029R

6. Press the START (enter) keypad when the correct time in minutes appears in the VFD. The next option, “+036”, will appear in the VFD.

NOTE: To program “+036” (Set Real-Time Clock Hours), refer to option 36. To program other options, refer to the appropriate section.

Figure 106

4. When “+035” appears in the VFD, press the

START (enter) keypad. The current time in minutes will appear in the VFD.

C796I

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 70

Programming NetMaster

36. Set Real-Time Clock Hours “+036”

This option allows the owner to set NetMaster’s internal clock to the correct time in hours.

How to Program the Clock Hours

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 108

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+036” appears in the VFD. Refer to Figure 109.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the hours to the correct time. Refer to Figure 110.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 110

neednew#2

B029R

6. Press the START (enter) keypad when the correct time in hours appears in the VFD. The next option, “+037”, will appear in the VFD.

NOTE: To program “+037” (Set Real-Time Clock Day), refer to option 37. To program other options, refer to the appropriate section.

C797I

Figure 109

4. When “+036” appears in the VFD, press the

START (enter) keypad. The current time in hours will appear in the VFD.

NOTE: The hours will be displayed in military time.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 71

Programming NetMaster

37. Set Real-Time Clock Day “+037”

This option allows the owner to set NetMaster’s internal clock to the correct day of the week.

How to Program the Clock Day

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 111

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+037” appears in the VFD. Refer to Figure 112.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the day until correct. Refer to Figure 113.

NOTE: Sunday is considered day one (001), Monday is day two (002) and so on.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 113

neednew#2

B029R

6. Press the START (enter) keypad when the correct day appears in the VFD. The next option, “+038”, will appear in the VFD.

Figure 112

4. When “+037” appears in the VFD, press the

START (enter) keypad. The current day of the week will appear in the VFD.

C798I

NOTE: To program “+038” (Set Real-Time Clock Date), refer to option 38. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 72

Programming NetMaster

38. Set Real-Time Clock Date “+038”

This option allows the owner to set NetMaster’s internal clock to the correct day of the month.

How to Program the Clock Date

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 114

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+038” appears in the VFD. Refer to Figure 115.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the day of the month until correct. Refer to Figure 116.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 116

neednew#2

B029R

6. Press the START (enter) keypad when the correct day of the month appears in the VFD. The next option, “+039”, will appear in the VFD.

NOTE: To program “+039” (Set Real-Time Clock Month), refer to option 39. To program other options, refer to the appropriate section.

Figure 115

4. When “+038” appears in the VFD, press the

START (enter) keypad. The current day of the month will appear in the VFD.

C799I

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 73

Programming NetMaster

39. Set Real-Time Clock Month “+039”

This option allows the owner to set NetMaster’s internal clock to the correct month.

How to Program the Clock Month

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 117

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+039” appears in the VFD. Refer to Figure 118.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the month until correct. Refer to Figure 119.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 119

neednew#2

B029R

6. Press the START (enter) keypad when the correct month appears in the VFD. The next option, “+040”, will appear in the VFD.

NOTE: To program “+040” (Set Real-Time Clock Year), refer to option 40. To program other options, refer to the appropriate section.

Figure 118

4. When “+039” appears in the VFD, press the

START (enter) keypad. The current month will appear in the VFD.

C800I

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 74

Programming NetMaster

40. Set Real-Time Clock Year “+040”

This option allows the owner to set NetMaster’s internal clock to the correct year.

How to Program the Clock Year

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 120

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the year until correct. Refer to Figure 122.

NOTE: The year 2000 is “00”, the year 2001 is “01” and so on.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+040” appears in the VFD. Refer to Figure 121.

Figure 121

4. When “+040” appears in the VFD, press the START (enter) keypad. The current year will appear in the VFD.

C801I

Figure 122

6. Press the START (enter) keypad when the correct year appears in the VFD. The next option, “+041”, will appear in the VFD.

NOTE: To program “+041” (Set Real-Time Clock Century), refer to option 41. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 75

Programming NetMaster

41. Set Real-Time Clock Century “+041”

This option allows the owner to set NetMaster’s internal clock to the correct century.

How to Program the Clock Century

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

Figure 123

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+041” appears in the VFD. Refer to Figure 124.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the century until correct. Refer to Figure 125.

NOTE: The digits “20” are used for century.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 125

neednew#2

6. Press the START (enter) keypad when the correct century appears in the VFD. The next option,

“+042”, will appear in the VFD.

B029R

Figure 124

4. When “+041” appears in the VFD, press the

START (enter) keypad. The current century will appear in the VFD.

C802I

NOTE: To program “+042” (Normal PreWash #1 Fill/Tumble Time), refer to option 42. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 76

Programming NetMaster

42. Normal PreWash #1 Fill/Tumble Time “+042”

This option allows the owner to set the amount of time for PreWash #1 during fill and tumble of the Normal cycle.

How to Program Normal PreWash #1 Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 128.

NOTE: The Normal PreWash #1 Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

Figure 126

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+042” appears in the VFD. Refer to Figure 127.

Figure 127

4. When “+042” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Normal PreWash #1 Fill/ Tumble Time will appear in the VFD.

Figure 128

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+043”, will appear in the VFD.

NOTE: To program “+043” (Normal PreWash #2 Fill/Tumble Time), refer to option 43 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

C803I

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 77

Programming NetMaster

44. Normal Wash Fill/Tumble Time “+044”

This option allows the owner to set the amount of wash fill/tumble time for the Normal cycle.

How to Program Normal Wash Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 129

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 131.

NOTE: The Normal Wash Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+044” appears in the VFD. Refer to Figure 130.

Figure 130

4. When “+044” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Normal Wash Fill/Tumble Time will appear in the VFD.

C805I

Figure 131

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+045”, will appear in the VFD.

NOTE: To program “+045” (Normal Rinse #1 Fill/ Tumble Time), refer to option 45. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 78

Programming NetMaster

45. Normal Rinse #1 Fill/Tumble Time “+045”

This option allows the owner to set the amount of rinse #1 fill/tumble time for the Normal cycle.

How to Program Normal Rinse #1 Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 132

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 134.

NOTE: The Normal Rinse #1 Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+045” appears in the VFD. Refer to Figure 133.

Figure 133

4. When “+045” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Normal Rinse #1 Fill/Tumble Time will appear in the VFD.

C806I

Figure 134

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+046”, will appear in the VFD.

NOTE: To program “+046” (Normal Rinse Extra Fill/Tumble Time), refer to option 46 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 79

Programming NetMaster

C808I

47. Normal Rinse Final Fill/Tumble Time “+047”

This option allows the owner to set the amount of time for a final rinse fill/tumble time for the Normal cycle.

How to Program Normal Rinse Final Fill/ Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 135

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 137.

NOTE: The Normal Rinse Final Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+047” appears in the VFD. Refer to Figure 136.

Figure 136

4. When “+047” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Normal Rinse Final Fill/ Tumble Time will appear in the VFD.

C808I

Figure 137

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+048”, will appear in the VFD.

NOTE: To program “+048” (Normal Spin Extract Time), refer to option 48. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 80

Programming NetMaster

C809I

48. Normal Spin Extract Time “+048”

This option allows the owner to set the amount of time for extraction during the Normal cycle.

How to Program Normal Spin Extract Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 138

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+048” appears in the VFD. Refer to Figure 139.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 140.

NOTE: The Normal Spin Extract Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 140

neednew#2

B029R

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+049”, will appear in the VFD.

Figure 139

4. When “+048” appears in the VFD, press the

START (enter) keypad. The current number of minutes set for the Normal Spin Extract Time will appear in the VFD.

C809I

NOTE: To program “+049” (Normal Spin Extract Speed), refer to option 49 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 81

Programming NetMaster

C812I

51. Permanent Press PreWash #1 Fill/Tumble Time “+051”

This option allows the owner to set the amount of PreWash #1 fill/tumble time for the Permanent Press cycle.

How to Program Permanent Press PreWash #1 Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 141

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 143.

NOTE: The Permanent Press PreWash #1 Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+051” appears in the VFD. Refer to Figure 142.

Figure 142

4. When “+051” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Permanent Press PreWash #1 Fill/Tumble Time will appear in the VFD.

C812I

Figure 143

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+052”, will appear in the VFD.

NOTE: To program “+052” (Permanent Press PreWash #2 Fill/Tumble Time), refer to option 52 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 82

Programming NetMaster

C814I

53. Permanent Press Wash Fill/Tumble Time “+053”

This option allows the owner to set the amount of wash fill/tumble time for the Permanent Press cycle.

How to Program Permanent Press Wash Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 144

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 146.

NOTE: The Permanent Press Wash Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+053” appears in the VFD. Refer to Figure 145.

Figure 145

4. When “+053” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Permanent Press Wash Fill/ Tumble Time will appear in the VFD.

C814I

Figure 146

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+054”, will appear in the VFD.

NOTE: To program “+054” (Permanent Press Rinse #1 Fill/Tumble Time), refer to option 54. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 83

Programming NetMaster

C815I

54. Permanent Press Rinse #1 Fill/Tumble Time “+054”

This option allows the owner to set the amount of rinse #1 fill/tumble time for the Permanent Press cycle.

How to Program Permanent Press Rinse #1 Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 147

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 149.

NOTE: The Permanent Press Rinse #1 Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+054” appears in the VFD. Refer to Figure 148.

Figure 148

4. When “+054” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Permanent Press Rinse #1 Fill/Tumble Time will appear in the VFD.

C815I

Figure 149

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+055”, will appear in the VFD.

NOTE: To program “+055” (Permanent Press Rinse Extra Fill/Tumble Time), refer to option 55 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 84

Programming NetMaster

C817I

56. Permanent Press Rinse Final Fill/Tumble Time “+056”

This option allows the owner to set the amount of final rinse fill/tumble time for the Permanent Press cycle.

How to Program Permanent Press Rinse Final Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 150

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+056” appears in the VFD. Refer to Figure 151.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 152.

NOTE: The Permanent Press Rinse Final Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 152

neednew#2

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+057”, will appear in the VFD.

B029R

Figure 151

4. When “+056” appears in the VFD, press the

START (enter) keypad. The current number of minutes set for the Permanent Press Rinse Final Fill/Tumble Time will appear in the VFD.

C817I

NOTE: To program “+057” (Permanent Press Spin Extract Time), refer to option 57. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 85

Programming NetMaster

57. Permanent Press Spin Extract Time “+057”

This option allows the owner to set the amount of time for extraction during the Permanent Press cycle.

How to Program Permanent Press Spin Extract Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 153

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 155.

NOTE: The Permanent Press Spin Extract Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+057” appears in the VFD. Refer to Figure 154.

Figure 154

4. When “+057” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Permanent Press Spin Extract Time will appear in the VFD.

Figure 155

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+058”, will appear in the VFD.

NOTE: To program “+058” (Permanent Press Spin Extract Speed), refer to option 58 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

C818I

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 86

Programming NetMaster

C862I

62. Delicates Wash Fill/Tumble Time “+062”

This option allows the owner to set the amount of wash fill/tumble time for the Delicates cycle.

How to Program Delicates Wash Fill/ Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 156

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 158.

NOTE: The Delicates Wash Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+062” appears in the VFD. Refer to Figure 157.

Figure 157

4. When “+062” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Delicates Wash Fill/Tumble Time will appear in the VFD.

C862I

Figure 158

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+063”, will appear in the VFD.

NOTE: To program “+063” (Delicates Rinse #1 Fill/Tumble Time), refer to option 63. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 87

Programming NetMaster

C863I

63. Delicates Rinse #1 Fill/Tumble Time “+063”

This option allows the owner to set the amount of rinse #1 fill/tumble time for the Delicates cycle.

How to Program Delicates Rinse #1 Fill/ Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 159

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 161.

NOTE: The Delicates Rinse #1 Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+063” appears in the VFD. Refer to Figure 160.

Figure 160

4. When “+063” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Delicates Rinse #1 Fill/ Tumble Time will appear in the VFD.

C863I

Figure 161

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+064”, will appear in the VFD.

NOTE: To program “+064” (Delicates Rinse Extra Fill/Tumble Time), refer to option 64 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 88

Programming NetMaster

C865I

65. Delicates Rinse Final Fill/Tumble Time “+065”

This option allows the owner to set the amount of final rinse fill/tumble time for the Delicates cycle.

How to Program Delicates Rinse Final Fill/Tumble Time

1. Control must be in Manual Mode. Refer to

Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-)

keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 162

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 164.

NOTE: The Delicates Rinse Final Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+065” appears in the VFD. Refer to Figure 163.

Figure 163

4. When “+065” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Delicates Rinse Final Fill/Tumble Time will appear in the VFD.

C865I

Figure 164

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+066”, will appear in the VFD.

NOTE: To program “+066” (Delicate Spin Extract Time), refer to option 66. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 89

Programming NetMaster

66. Delicates Spin Extract Time “+066”

This option allows the owner to set the amount of time for extraction during the Delicates cycle.

How to Program Delicates Spin Extract Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 165

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 167.

NOTE: The Delicates Spin Extract Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+066” appears in the VFD. Refer to Figure 166.

Figure 166

4. When “+066” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Delicates Spin Extract Time will appear in the VFD.

Figure 167

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+067”, will appear in the VFD.

NOTE: To program “+067” (Delicates Spin Extract Speed), refer to option 67 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

CHM6R

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 90

Programming NetMaster

69. Special Wash PreWash #1 Fill/Tumble Time “+069”

This option allows the owner to set the amount of time for PreWash #1 during fill and tumble of the Delicates cycle.

How to Program Special Wash PreWash #1 Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 170.

NOTE: The Special Wash PreWash #1 Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

Figure 168

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+069” appears in the VFD. Refer to Figure 169.

Figure 169

4. When “+069” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Special Wash PreWash #1 Fill/Tumble Time will appear in the VFD.

Figure 170

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+070”, will appear in the VFD.

NOTE: To program “+070” (Special Wash PreWash #2 Fill/Tumble Time), refer to option 70 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

CHM7R

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 91

Programming NetMaster

71. Special Wash Wash Fill/Tumble Time “+071”

This option allows the owner to set the amount of wash fill/tumble time for the Special Wash cycle.

How to Program Special Wash Wash Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 171

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 173.

NOTE: The Special Wash Wash Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+071” appears in the VFD. Refer to Figure 172.

Figure 172

4. When “+071” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Special Wash Wash Fill/Tumble Time will appear in the VFD.

CHM8R

Figure 173

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+072”, will appear in the VFD.

NOTE: To program “+072” (Special Wash Rinse #1 Fill/Tumble Time), refer to option 72. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 92

Programming NetMaster

72. Special Wash Rinse #1 Fill/Tumble Time “+072”

This option allows the owner to set the amount of rinse #1 fill/tumble time for the Special Wash cycle.

How to Program Special Wash Rinse #1 Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 174

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 176.

NOTE: The Special Wash Rinse #1 Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+072” appears in the VFD. Refer to Figure 175.

Figure 175

4. When “+072” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Special Wash Rinse #1 Fill/Tumble Time will appear in the VFD.

CHM9R

Figure 176

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+073”, will appear in the VFD.

NOTE: To program “+073” (Special Wash Rinse Extra Fill/Tumble Time), refer to option 73 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 93

Programming NetMaster

74. Special Wash Rinse Final Fill/Tumble Time “+074”

This option allows the owner to set the amount of time for a final rinse fill/tumble in the Special Wash cycle.

How to Program Special Wash Rinse Final Fill/Tumble Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 177

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 179.

NOTE: The Special Wash Rinse Final Fill/Tumble Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+074” appears in the VFD. Refer to Figure 178.

CHM10R

Figure 178

4. When “+074” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Special Wash Rinse Final Fill/Tumble Time will appear in the VFD.

Figure 179

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+075”, will appear in the VFD.

NOTE: To program “+075” (Special Wash Spin Extract Time), refer to option 75. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 94

Programming NetMaster

75. Special Wash Spin Extract Time “+075”

This option allows the owner to set the amount of time for extraction during the Special Wash cycle.

How to Program Special Wash Spin Extract Time

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 180

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number of minutes displayed in the VFD to the desired number of minutes. Refer to Figure 182.

NOTE: The Special Wash Spin Extract Time can be set from zero (0) to 15 minutes.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

neednew#2

B029R

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+075” appears in the VFD. Refer to Figure 181.

CHM17R

Figure 181

4. When “+075” appears in the VFD, press the START (enter) keypad. The current number of minutes set for the Special Wash Spin Extract Time will appear in the VFD.

Figure 182

6. Press the START (enter) keypad when the correct number of minutes appears in the VFD. The next option, “+076”, will appear in the VFD.

NOTE: To program “+076” (Special Wash Spin Extract Speed), refer to option 76 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 95

Programming NetMaster

81. Control Configuration Data #1 “+081”

This option allows the owner to turn ON or turn OFF preprogrammed capabilities within NetMaster.

How to Program the Control Configuration Data #1

1. Control must be in Manual Mode. Refer to

Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-)

keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

C762I

Figure 183

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+081” appears in the VFD. Refer to Figure 184.

5. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number to the desired number selected from Table 5. Refer to Figure 185.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 185

neednew#2

B029R

6. Press the START (enter) keypad when the correct number appears in the VFD. The next option, “+082”, will appear in the VFD.

NOTE: To program “+082” (Control Configuration Data #2), refer to option 82 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

Figure 184

4. When “+081” appears in the VFD, press the

START (enter) keypad. A number will appear in the VFD. This number corresponds to the current Control Configuration Data #1 Value.

F232151

CHM11R

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

Page 96

Programming NetMaster

Configuration #1 Programming

To change any or all of these configuration options, review the following descriptions carefully and choose

Refer to Ta b le 5 to turn on or turn off the preprogrammed daylight savings option, wash temperature display option, infra-red access option,

the appropriate configuration value from Table 5. Enter the appropriate value in step 5 on the previous page.

decimal point option, manual programming and the automatic collect option in NetMaster.

Daylight Savings This option automatically sets the clock in NetMaster to account for the time change during

Daylight Savings. OFF = Turns off the automatic daylight savings option programmed in NetMaster. ON = Turns on the automatic daylight savings option programmed in NetMaster.

Wash Temperature This option determines if the temperature LEDs indicate the selected wash temperature during the

entire cycle or indicates fill temperature during each rinse. SELECT (OFF)= Selected wash temperature remains on for entire cycle. ACTUAL (ON)= LEDs indicate actual water temperature during every fill step. LEDs will be off during distribute and spin steps.

Infra-red Access This option determines if a Micro-Wand can access or program NetMaster.

OFF = Turns off the infra-red access by the Micro-Wand. ON = Turns on the infra-red access by the Micro-Wand.

Decimal Point This option determines if a decimal point is used when displaying the vend price (i.e., machines

using token currency may choose to remove the decimal point). OFF = Turns off the decimal point from appearing in the VFD. ON = Turns on the decimal point to appear in the VFD.

Automatic Collect This option automatically collects all audit data information whenever the Micro-Wand

communicates with the control. Turn off Automatic Collect to prevent access to collection information when using an outside source to program NetMaster. OFF = Turns off the automatic collect with the Micro-Wand. ON = Turns on the automatic collect with the Micro-Wand.

Manual Programming This option allows special programming functions to be accessed manually rather than requiring the

use of a Micro-Wand or other communication source. OFF = Turns off Manual Programming. ON = Turns on Manual Programming.

F232151

Page 97

“+081”

Programming NetMaster

Config. Value

Auto

Collect

Manual

Progr.

Access

Decimal

Point

IR Access Wash Temp

0 OFF OFF OFF OFF OFF OFF

1 OFF OFF OFF OFF OFF ON

2 OFF OFF OFF OFF ON OFF

3 OFF OFF OFF OFF ON ON

4 OFF OFF OFF ON OFF OFF

5 OFF OFF OFF ON OFF ON

6 OFF OFF OFF ON ON OFF

7 OFF OFF OFF ON ON ON

8OFFOFFON OFF OFF OFF

9OFFOFFON OFF OFF ON

10 OFF OFF ON OFF ON OFF

11 OFF OFF ON OFF ON ON

12 OFF OFF ON ON OFF OFF

13 OFF OFF ON ON OFF ON

14 OFF OFF ON ON ON OFF

15 OFF OFF ON ON ON ON

16 OFF ON OFF OFF OFF OFF

17 OFF ON OFF OFF OFF ON

18 OFF ON OFF OFF ON OFF

19 OFF ON OFF OFF ON ON

20 OFF ON OFF ON OFF OFF

21 OFF ON OFF ON OFF ON

22 OFF ON OFF ON ON OFF

23 OFF ON OFF ON ON ON

24 OFF ON ON OFF OFF OFF

25 OFF ON ON OFF OFF ON

26 OFF ON ON OFF ON OFF

27 OFF ON ON OFF ON ON

28 OFF ON ON ON OFF OFF

29 OFF ON ON ON OFF ON

30 OFF ON ON ON ON OFF

31 OFF ON ON ON ON ON

32 ON OFF OFF OFF OFF OFF

33 ON OFF OFF OFF OFF ON

34 ON OFF OFF OFF ON OFF

35 ON OFF OFF OFF ON ON

Daylight Savings

F232151

Table 5 (Continued)

Page 98

Programming NetMaster

Table 5 (Continued)

“+081”

Config. Value

Auto

Collect

Manual

Progr.

Access

Decimal

Point

IR Access Wash Temp

36 ON OFF OFF ON OFF OFF

37 ON OFF OFF ON OFF ON

38 ON OFF OFF ON ON OFF

39 ON OFF OFF ON ON ON

40 ON OFF ON OFF OFF OFF

41 ON OFF ON OFF OFF ON

42 ON OFF ON OFF ON OFF

43 ON OFF ON OFF ON ON

44 ON OFF ON ON OFF OFF

45 ON OFF ON ON OFF ON

46 ON OFF ON ON ON OFF

47 ON OFF ON ON ON ON

48 ON ON OFF OFF OFF OFF

49 ON ON OFF OFF OFF ON

50 ON ON OFF OFF ON OFF

51 ON ON OFF OFF ON ON

52 ON ON OFF ON OFF OFF

53 ON ON OFF ON OFF ON

54 ON ON OFF ON ON OFF

55 ON ON OFF ON ON ON

56 ON ON ON OFF OFF OFF

57 ON ON ON OFF OFF ON

58 ON ON ON OFF ON OFF

59 ON ON ON OFF ON ON

60 ON ON ON ON OFF OFF

61 ON ON ON ON OFF ON

62 ON ON ON ON ON OFF

63 ON ON ON ON ON ON

Daylight Savings

F232151

Page 99

Programming NetMaster

114. Lucky Option “+114”

This option allows the owner to program the machine to provide a free vend cycle to customers after a certain number of machine cycles have occurred.

For coin models, “FrEE” will be displayed five minutes after the completion of the programmed number of cycles has occurred. The cycle can then be started by pressing the START (enter) pad.

For card models, when a card is inserted, the VFD will display “bAL” followed by the card balance. When the user presses the START pad, a zero vend will be deducted from the card. The VFD will display “WAIT”. The VFD will then display “FrEE” for five seconds and then the cycle time will be displayed. When the card is removed, the VFD will flash the remaining balance for three seconds and will then revert back to the cycle time.

How to Program Lucky Option

1. Control must be in Manual Mode. Refer to Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-) keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

5. Locate the desired number in the first column of Table 6 below.

“+114”

Lucky Option

Value

1 – 127 OFF 1 – 127

129 ON 1

130 ON 2

131 – 255 ON 3 – 127

Lucky Cycle

ON/OFF

Table 6

Number of

Cycles

6. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number until correct. Refer to Figure 188.

C762I

Figure 186

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until

“+114” appears in the VFD. Refer to Figure 187.

CHM12R

Figure 187

4. When “+114” appears in the VFD, press the START (enter) keypad. A number will appear in the VFD. This number corresponds to the current Lucky Option Programming Value.

B029R

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 188

7. Press the START (enter) keypad when the correct number appears in the VFD. The next option, “+115”, will appear in the VFD.

NOTE: To program “+115” (Special Cycle Option), refer to option 115 in Programming NetMaster in the Enhanced Programming Guide, available at extra cost. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

F232151

Page 100

Programming NetMaster

118. Auto-Flush Option “+118”

This option programs the control to automatically flush the dispenser compartments at set times and intervals to keep the compartments clean.

The owner can select Auto-Flush to occur after one (1) to 127 cycles and can determine the time and days of week Auto-Flush will occur. If zero (0) is selected for cycles, the Auto-Flush will always occur on the selected time and day.

How to Program Auto-Flush Cycle Option

1. Control must be in Manual Mode. Refer to

Entering the Manual Mode.

2. Press the DELICATES (+) or the COLD (-)

keypad until “PrOg” appears in the VFD. Press the START (enter) keypad and “+001” will appear in the VFD.

6. Press the DELICATES (+) or the COLD (-) keypad to increase or decrease the current number until correct. Refer to Figure 191.

1 Press this pad (+) to scroll forward or increase a value 2 Press this pad (enter) to choose a selected value or

option

3 Press this pad (-) to scroll back or decrease a value

Figure 191

neednew#2

B029R

Figure 189

3. Press the DELICATES (+) or the COLD (-) keypad to scroll through the programmable options until “+118” appears in the VFD. Refer to Figure 190.

CHM13R

Figure 190

4. When “+118” appears in the VFD, press the START (enter) keypad. A number will appear in the VFD. This number corresponds to the current Auto-Flush Option Programming Value.

5. Locate the desired number in Table 7.

C762I

7. Press the START (enter) keypad when the correct number appears in the VFD. The next option, “+119”, will appear in the VFD.

NOTE: To program “+119” (Auto-Flush Hour), refer to option 119. To program other options, refer to the appropriate section.

How to Exit Programming Feature

1. Be sure the control shows a programmable option, not a value.

2. While pressing and holding the NORMAL keypad with one hand, press the PERM PRESS keypad with the other hand. The control will revert back to the Ready Mode. Refer to Figure 2.

“+118”

Auto-Flush

Option Value

0 – 127 OFF 0 – 127

128 ON 0

129 ON 1

130 ON 2

131 – 255 ON 3 – 127

Auto-Flush

ON/OFF

Number of

Cycles

Table 7

F232151