Alliance Laundry Systems CA120L, SU120E, SU200L, DR170G2-BA170L, DR170G2-BA170N Installation Operation & Maintenance
...
Tumble Dryers
TMB1268C_SVG
120 Pound (55 Kilogram) Capacity
170 Pound (77 Kilogram) Capacity
200 Pound (90 Kilogram) Capacity
Starting Serial No. 0907003062
Refer to Page 8 for Model Identification
Installation/Operation/Maintenance
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com
Part No. 70458101ENR10
August 2015
Installation must conform with local codes or, in the absence of local codes, with:
In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/ NFPA 54 “National Fuel Gas
Code” and Standard ANSI/NFPA 70 “National Electric Code.”
In Canada, installation must comply with Standards CAN/CSA-B149.1 or Natural Gas and Propane Installation Code and CSA C22.1,
latest edition, Canadian Electric Code, Part I.
In Australia and New Zealand, installation must comply with the Gas Installations Standard AS/NZS 5601 Part 1: General Installations.
WARNING
FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion
or to prevent property damage, personal injury or death.
W033
WARNING
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building or area of all occupants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or the gas supplier.
IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the user
smells gas. These instructions must be posted in a prominent location. Step-by-step instructions of the above
safety information must be posted in a prominent location near the tumble dryer for customer use.
IMPORTANT: The installer must fully test the tumble dryer after installation and demonstrate to the owner how to
operate the machine.
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
W052
3 Part No. 70458101ENR10
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumble dryer before servicing.
• Close gas shut-off valve to gas tumble dryer before servicing.
• Close steam valve to steam tumble dryer before servicing.
• Never start the tumble dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure
that the tumble dryer is properly grounded.
W002R1
WARNING
• Installation of unit must be performed by a qualified installer.
• Install tumble dryer according to manufacturer’s instructions and local codes.
• DO NOT install a tumble dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with tumble
dryer. Refer to section on connecting exhaust system. Flexible venting materials are known to collapse, be
easily crushed, and trap lint. These conditions will obstruct tumble dryer airflow and increase the risk of
fire.
The following information applies to the state of Massachusetts, USA.
• This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.
• This appliance must be installed with a 36 inch [91 cm] long flexible gas connector.
• A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.
• This appliance must not be installed in a bedroom or bathroom.
W752R1
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4 Part No. 70458101ENR10
Table of Contents
Introduction........................................................................................... 8
Model Identification .......................................................................................8
Contact Information...................................................................................... 10
Safety Information................................................................................12
Explanation of Safety Messages..................................................................... 12
Important Safety Instructions......................................................................... 12
Specifications and Dimensions.............................................................. 14
Specifications and Dimensions ...................................................................... 14
120 Series Tumble Dryer Dimensions and Exhaust Outlet Locations ................ 16
170 and 200 Series Tumble Dryer Dimensions and Exhaust Outlet Locations.....17
Electric and Gas Connection Locations for Gas Models Through 3/10/13...........18
Electric and Gas Connection Locations for Gas Models Starting 3/11/13............19
Electric and Steam Connection Locations for Steam Models Through 3/10/13....20
Electric and Steam Connection Locations for Steam Models Starting 3/11/13.....21
Electric Connection Location for Electric Models............................................ 23
Installation........................................................................................... 24
Pre-Installation Inspection............................................................................. 24
Location Requirements..................................................................................24
Position and Level the Tumble Dryer..............................................................25
Mounting..................................................................................................... 25
Fire Suppression System (Optional Equipment)............................................... 26
Check Local Codes and Permits..................................................................26
Water Requirements.................................................................................. 26
Water Connections.................................................................................... 26
Electrical Requirements............................................................................. 28
Auxiliary Alarm........................................................................................ 28
Before Placing Tumble Dryer into Service...................................................... 28
Required for CE Models Only.................................................................... 30
Installing CE Gas Drying Tumble Dryer......................................................... 30
General Information.................................................................................. 30
CE Orifices...............................................................................................31
Properties of CE Gases.............................................................................. 33
Changing Gas Configuration...................................................................... 33
Specific Conversion Procedures..................................................................34
Exhaust Requirements..........................................................................36
Exhaust Requirements...................................................................................36
©
Copyright 2015, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5 Part No. 70458101ENR10
Layout......................................................................................................... 36
Make-Up Air................................................................................................36
Venting........................................................................................................36
Alternate Venting for 120 Series Tumble Dryers.......................................... 37
Individual Venting.....................................................................................38
Manifold Venting...................................................................................... 39
Gas Requirements.................................................................................42
Gas Requirements.........................................................................................42
Gas Supply Pipe Sizing and Looping.............................................................. 44
Low Pressure Gas Pipe Sizes......................................................................44
High Pressure Gas Pipe Sizes..................................................................... 46
High Altitude Orifice Sizing ......................................................................... 48
Electrical Requirements........................................................................51
Electrical Requirements.................................................................................51
Wiring Diagram............................................................................................51
Grounding Instructions..................................................................................51
For CE Models Only..................................................................................52
Service/Ground Location........................................................................... 52
To Connect Electrical Service To The Tumble Dryer....................................... 54
Jumper Configuration Instructions..................................................................54
Ferrite Ring Installation ................................................................................54
Electrical Specifications ............................................................................... 57
Steam Requirements.............................................................................59
Steam Requirements......................................................................................59
Piping Recommendations.............................................................................. 63
Installing Steam Trap and Making Condensate Return Connections...................63
Thermal Oil Prep.......................................................................................... 63
Operating Instructions..........................................................................64
Operating Instructions................................................................................... 64
Emergency Stop Button On CE Models.......................................................... 64
Operating Instructions................................................................................... 64
Reversing Operation......................................................................................65
Control Instructions.......................................................................................65
Dual Digital Timer Control........................................................................ 65
Electronic OPL Micro Control....................................................................67
LED OPL Control .................................................................................... 68
UniLinc Control ....................................................................................... 69
DX4 OPL Control..................................................................................... 70
Diagnostic Microprocessor Control ............................................................ 71
DMP OPL Models.....................................................................................71
Ignition Control Operation and Troubleshooting for Models Starting 3/11/13..... 73
Internal Control Failure..............................................................................74
Troubleshooting........................................................................................ 74
Proper Electrode Location..........................................................................75
Flame Current Measurement.......................................................................75
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 Part No. 70458101ENR10
Ignition Control Operation for Non-CE Models Through 3/10/13...................... 75
Ignition Control Operation for CE Models Through 3/10/13............................. 75
System Tests.............................................................................................76
Diagnostic LED (DGN LED)/Error Codes...................................................76
Adjustments......................................................................................... 78
Adjustments................................................................................................. 78
Gas Burner Air Shutter.................................................................................. 78
Airflow Switch ............................................................................................ 79
Loading Door Switch.................................................................................... 79
Loading Door Catch (120 and 170 Series Models)........................................... 79
Loading Door Strike (200 Series Models)........................................................80
Belt Drive ................................................................................................... 80
Maintenance......................................................................................... 82
Daily........................................................................................................... 82
Monthly....................................................................................................... 82
Quarterly......................................................................................................82
Bi-Annually................................................................................................. 83
Annually...................................................................................................... 83
Fire Suppression System (Optional Equipment) Maintenance Test.................... 83
Before You Call for Service...................................................................85
Removing Tumble Dryer from Service..................................................86
Disposal of Unit.................................................................................... 87
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 Part No. 70458101ENR10
Introduction
Model Identification
Information in this manual is applicable to these models. Refer
to the machine serial plate for the model number.
Gas Steam/Thermal Oil Electric
Introduction
120 Series
(55 Kg)
CA120L
CA120N
CK120N
CT120L
CT120N
CU120L
CU120N
DR120G2-BA120L
DR120G2-BA120N
DR120G2-BK120N
DR120G2-BT120L
DR120G2-BT120N
DR120G2-BU120L
DR120G2-BU120N
HA120L
HA120N
HK120N
HU120L
HU120N
IPD120G2
IT120L
IT120N
LA120L
LA120N
LK120N
LT120L
LT120N
LU120L
LU120N
PA120L
PA120N
PK120N
PT120L
PT120N
SA120L
SA120N
SK120N
ST120L
ST120N
SU120L
SU120N
UA120L
UA120N
UK120N
UT120L
UT120N
UU120L
UU120N
XT120L
XT120N
XU120L
CT120S
CT120T
CU120S
CU120T
DR120S2-BT120S
DR120S2-BT120T
DR120S2-BU120S
DR120S2-BU120T
HT120S
HT120T
HU120S
HU120T
IPD120S2
IT120S
IT120T
LT120S
LT120T
PT120S
PT120T
PU120S
PU120T
ST120S
ST120T
SU120S
SU120T
UT120S
UT120T
UU120S
UU120T
XT120S
XT120T
XU120S
XU120T
YT120S
CT120E
CU120E
DR120E2-BT120E
DR120E2-BU120E
HT120E
HU120E
IT120E
LT120E
LU120E
PT120E
PU120E
ST120E
SU120E
UT120E
UU120E
YT120E
YU120E
HT120L
HT120N
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
PU120L
PU120N
XU120N
YT120L
YT120N
YU120L
YU120N
LU120S
LU120T
8 Part No. 70458101ENR10
YT120T
YU120S
YU120T
Table continues...
Gas Steam/Thermal Oil Electric
Introduction
170 Series
(77 Kg)
CA170L
CA170N
CK170N
CT170L
CT170N
CU170L
CU170N
DR170G2-BA170L
DR170G2-BA170N
DR170G2-BK170N
DR170G2-BT170L
DR170G2-BT170N
DR170G2-BU170L
DR170G2-BU170N
HA170L
HA170N
HK170N
HT170L
HT170N
HU170L
HU170N
IPD170G2
IT170L
IT170N
LA170L
LA170N
LK170N
LT170L
LT170N
LU170L
LU170N
PA170L
PA170N
PK170N
PT170L
PT170N
PU170L
PU170N
SA170L
SA170N
SK170N
ST170L
ST170N
SU170L
SU170N
UA170L
UA170N
UK170N
UT170L
UT170N
UU170L
UU170N
XT170L
XT170N
XU170L
XU170N
YT170L
YT170N
YU170L
YU170N
CT170S
CT170T
CU170S
CU170T
DR170S2-BT170S
DR170S2-BT170T
DR170S2-BU170S
DR170S2-BU170T
HT170S
HT170T
HU170S
HU170T
IPD170S2
IT170S
IT170T
LT170S
LT170T
LU170S
LU170T
PT170S
PT170T
PU170S
PU170T
ST170S
ST170T
SU170S
SU170T
UT170S
UT170T
UU170S
UU170T
XT170S
XT170T
XU170S
XU170T
YT170S
YT170T
YU170S
YU170T
Not Applicable
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Table continues...
9 Part No. 70458101ENR10
Introduction
Gas Steam/Thermal Oil Electric
200 Series
(90 Kg)
CA200L
CA200N
CT200L
CT200N
CU200L
CU200N
DR200G2-BA200L
DR200G2-BA200N
DR200G2-BT200L
DR200G2-BT200N
DR200G2-BU200L
DR200G2-BU200N
HA200L
HA200N
HT200L
HT200N
HU200L
HU200N
IT200L
IT200N
LA200L
LA200N
LT200L
LT200N
LU200L
LU200N
PA200L
PA200N
PT200L
PT200N
PU200L
PU200N
SA200L
SA200N
ST200L
ST200N
SU200L
SU200N
UA200L
UA200N
UT200L
UT200N
UU200L
UU200N
CT200S
CT200T
CU200S
CU200T
DR200S2-BT200S
DR200S2-BT200T
DR200S2-BU200S
DR200S2-BU200T
HT200S
HT200T
HU200S
HU200T
IT200S
IT200T
LT200S
LT200T
LU200S
LU200T
PT200S
PT200T
PU200S
PU200T
ST200S
ST200T
SU200S
SU200T
UT200S
UT200T
UU200S
UU200T
Not Applicable
Explanation of digit in 6th position of model number:
E = Electric
L = Liquid Petroleum (L.P.) Gas
N = Natural Gas
S = Steam
T = Thermal Oil
Includes models with the following control suffixes
R3 – reversing DX4 OPL RE – reversing LED OPL RQ – reversing dual digital timer
RD – reversing DMP OPL RM – reversing OPL micro RU – reversing UniLinc OPL
U.S.A.
Contact Information
If service is required, contact the nearest Factory Authorized
Service Center.
If you are unable to locate an authorized service center or are unsatisfied with the service performed on your unit, contact:
Alliance Laundry Systems
www.alliancelaundry.com
Phone: +1 (920) 748-3121 Ripon, Wisconsin
+32 56 41 20 54 Wevelgem, Belgium
When calling or writing about your unit, PLEASE GIVE THE
MODEL AND SERIAL NUMBERS. The model and serial numbers are located on the serial plate. The serial plate will be in the
location shown in Figure 1 .
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
Date Purchased ______________________________
Model Number ______________________________
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10 Part No. 70458101ENR10
TMB2288N_SVG
1
120 170/200
1
Introduction
Serial Number _______________________________
Please include a copy of your bill of sale and any service receipts
you have.
WARNING
To reduce the risk of serious injury or death, DO
NOT repair or replace any part of the unit or attempt
any servicing unless specifically recommended in
the user-maintenance instructions or in published
user-repair instructions that you understand and
have the skills to carry out.
W329
If replacement parts are required, contact the source from where
you purchased your unit or call +1 (920) 748-3950 or +32 56 41
20 54 for the name and address of the nearest authorized parts
distributor.
1. Serial Plate
Figure 1
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11 Part No. 70458101ENR10
Safety Information
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,” and
“CAUTION”), followed by specific instructions, are found in this
manual and on machine decals. These precautions are intended
for the personal safety of the operator, user, servicer, and those
maintaining the machine.
DANGER
Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.
WARNING
Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.
CAUTION
Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or
property damage.
Additional precautionary statements (“IMPORTANT” and
“NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor
machine damage will occur if the procedure is not followed.
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock, serious injury or death to persons when using your tumbler,
follow these basic precautions.
W776
Save These Instructions
• Read all instructions before using the tumble dryer.
• Install the tumble dryer according to the INSTALLATION instructions. Refer to the EARTHING (grounding) instructions
for the proper earthing (grounding) of the tumble dryer. All
connections for electrical power, earthing (grounding) and gas
supply must comply with local codes and be made by licensed
personnel when required. It is recommended that the machine
be installed by qualified technicians.
• Do not install or store the tumble dryer where it will be exposed to water and/or weather. The tumble dryer cannot be
used in a closed room where the air supply is insufficient. If
necessary, ventilation grids must be installed in the doors or
the windows.
• This appliance must not be activated without lint/foam filter.
• When you perceive a gas odor, immediately switch off the gas
supply and ventilate the room. Do not switch on electrical appliances and do not pull electrical switches. Do not use
matches or lighters. Do not use a phone in the building. Warn
the fitter, and if so desired, the gas company, as soon as possible.
• To avoid fire and explosion, keep surrounding areas free of
flammable and combustible products. Regularly clean the
dryer drum and exhaust tube should be cleaned periodically
by competent maintenance personnel. Daily remove piled up
dust from filter and inside of filter compartment.
• Do not use or store flammable materials near this appliance.
• Do not dry articles that have been previously cleaned in,
washed in, soaked in or spotted with gasoline or machine oils,
vegetable or cooking oils, cleaning waxes or chemicals, drycleaning solvents, thinner or other flammable or explosive
substances as they give off vapors that could ignite, explode
or cause fabric to catch on fire by itself.
• Do not spray aerosols in the vicinity of this appliance while it
is in operation.
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows
filled with foam rubber pads should not be dried in the tumble
dryer. Do not use the appliance to dry materials with a low
melting temperature (PVC, rubber, etc.).
• Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder
with a damp cloth to remove particles of fiberglass.
• Do not allow children on or in the tumble dryer. This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.
• Do not reach into the tumble dryer if the cylinder is revolving.
• Use tumble dryer only for its intended purpose, drying fabrics. Always follow the fabric care instructions supplied by
the textile manufacturer and only use the dryer drum to dry
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12 Part No. 70458101ENR10
Safety Information
textiles that have been washed in water. Only insert spin-dried
linen in the dryer.
• Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns,
keep them out of the reach of children at all times (preferably
in a locked cabinet).
• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener
or product.
• Remove laundry immediately after tumble dryer stops.
• DO NOT operate the tumble dryer if it is smoking, grinding
or has missing or broken parts or removed guards or panels.
DO NOT tamper with the controls or bypass any safety devices.
• Tumble dryer will not operate with the loading door open. DO
NOT bypass the door safety switch to permit the tumble dryer
to operate with the door open. The tumble dryer will stop
tumbling when the door is opened. Do not use the tumble dryer if it does not stop tumbling when the door is opened or
starts tumbling without pressing or turning the START mechanism. Remove the tumble dryer from use and call for service.
• Tumble dryer(s) will not operate with lint panel open. DO
NOT bypass lint panel safety switch to permit the tumble dryer to operate with the lint panel open.
• Do not modify this appliance.
• Always clean the lint filter daily. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and dirt. The interior of the tumble
dryer and the exhaust duct should be cleaned periodically by
qualified service personnel.
• Solvent vapors from dry-cleaning machines create acids when
drawn through the heater of the drying unit. These acids are
corrosive to the tumble dryer as well as the laundry load being
dried. Be sure make-up air is free of solvent vapors.
• At the end of each working day, close off all main supplies of
gas, steam and current.
• Do not repair or replace any part of the tumble dryer, or attempt any servicing unless specifically recommended in the
user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry
out. ALWAYS disconnect and lockout the electrical power to
the tumble dryer before servicing. Disconnect power by shutting off appropriate breaker or fuse.
• Before the tumble dryer is removed from service or discarded,
remove the door to the drying compartment and the door to
the lint compartment.
• Failure to install, maintain, and/or operate this tumble dryer
according to the manufacturer’s instructions may result in
conditions which can produce bodily injury and/or property
damage.
NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the
tumble dryer.
Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do not understand.
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13 Part No. 70458101ENR10
Specifications and Dimensions
Specifications and Dimensions
Specifications and Dimensions
Refer to machine serial plate for additional specifications.
Specifications 120 Series 170 Series 200 Series
Heat dissipation of surface area exposed
to conditioned air: Btu/ft2 [Joules/m2]
Noise level measured during operation
at operator position of 3.3 feet (1 meter)
in front of machine and 5.2 feet (1.6 meters) from floor.
Cylinder Size: Inches [mm] 44 x 41 [1,118 x 1,041] 50.75 x 42.5 [1,289 x
Cylinder Capacity dry weight: Pounds
[kg]
Standard Packaging Weight:
Pounds [kg]
Standard Packaging Shipping Dimensions: Inch [mm]
Slat Crate Packaging Weight:
Pounds [kg]
Slat Crate Shipping Dimensions: Inch
[mm]
Gas and Electric 1,338 [607] 1,667 [756] 1,818 [825]
Steam 1,446 [656] 1,776 [806] 1,885 [855]
Gas and Electric 1,447 [656] 1,791 [812] 1,931 [876]
Steam 1,547 [702] 1,891 [858] 1,998 [906]
60 [681,392] 60 [681,392] 60 [681,392]
66 dBA 66 dBA 66 dBA
1,080]
120 [55] 170 [77] 200 [90]
48.5 x 71.5 x 90 [1,232 x
1,816 x 2,286]
53 x 74.5 x 90.75 [1,346 x
1,892 x 2,305]
55.63 x 73.75 x 99 [1,413
x 1,873 x 2,515]
60.13 x 76.75 x 99.75
[1,527 x 1,949 x 2,534]
50.75 x 50 [1,289 x 1,270]
55.63 x 81.25 x 99 [1,413
x 2,064 x 2,515]
60.13 x 84.25 x 101 [1,527
x 2,140 x 2,565]
Cylinder Motor: HP [kW] 0.75 [0.560] 0.75 [0.560] 0.75 [0.560]
Fan Motor: HP [kW] 1 [0.746] 3 [2.238] 3 [2.238]
Air Outlet Diameter: Inches [mm] 10 [254] 12 [300] 12 [300]
Maximum Static Back Pressure: W.C.I.
[mbar, kPa]
Maximum Airflow: C.F.M. [L/sec.] 1,600 [755] 2,450 [1,156] 2,450 [1,156]
Gas Models
Net Weight (approximate): Pounds [kg] 1,275 [578] 1,575 [716] 1,741 [790]
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
0.8 [2.0, 0.2] 0.8 [2.0, 0.2] 0.8 [2.0, 0.2]
Table continues...
14 Part No. 70458101ENR10
Specifications and Dimensions
Specifications 120 Series 170 Series 200 Series
Gas Connection Models through 3/10/13:
1 in. NPT 1 in. NPT
3/4 in. NPT
Models Starting 3/11/13: 1
in. NPT
Gas Burner Rating:
270,000 [285, 79.13] 395,000 [417, 115.77] 425,000 [448, 124.56]
Btu/hr. [Mj/hr., kW]
Steam Models
Net Weight (approximate): Pounds [kg] 1,375 [624] 1,675 [761] 1,808 [820]
Steam Connection 3/4 in. NPT inlet
3/4 in. NPT outlet
Steam Coil Rating at 100 psig:
405,000 [183.1] 648,000 [294.2] 648,000 [294.2]
3/4 in. NPT inlet
1 in. NPT outlet
3/4 in. NPT inlet
1 in. NPT outlet
Btu/hr. [kg/hr.] (recommended operating
pressure 80-100 psig)
Electric Models
Net Weight (approximate): Pounds [kg] 1,275 [578] Not Applicable Not Applicable
Heating Element Rating: Kilowatts
60 kW Not Applicable Not Applicable
(kW)
NOTE: All machines are shipped with extra nipple to
convert to metric thread (from Standard).
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15 Part No. 70458101ENR10
TMB2423N_SVG
H
U
C
D
E
Y
Z
F
K
G
J
X
I
V
W
B
A
1
Specifications and Dimensions
120 Series Tumble Dryer Dimensions and Exhaust Outlet Locations
1. Top View of Exhaust Duct
Cabinet Dimensions
Models A B C D E
120L/N/E 31.38 in. [797
mm]
120S 31.38 in. [797
mm]
Cabinet Dimensions
Models F G H I* J* K*
120L/N/E 46.38 in. [1,178
mm]
120S 46.38 in. [1,178
mm]
85.7 in. [2,177
mm]
85.58 in. [2,174
mm]
* Fire suppression system optional - may not be on machine. Refer to Position and Level the Tumble Dryer to temporarily re-
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
32.5 in. [826 mm] 46.5 in. [1,181
mm]
32.5 in. [826 mm] 46.5 in. [1,181
mm]
70 in. [1,778
mm]
70 in. [1,778
mm]
duce the heights of these models.
16 Part No. 70458101ENR10
41.6 in. [1,057
mm]
41.6 in. [1,057
mm]
49.91 in. [1,268
mm]
49.91 in. [1,268
mm]
43.2 in. [1,097
mm]
43.2 in. [1,097
mm]
67.92 in. [1,725
mm]
67.92 in. [1,725
mm]
61.5 in. [1,562
mm]
61.5 in. [1,562
mm]
TMB2424N_SVG
V
Y
X
W
F
K
G
I
J
E
D
C
H
B
A
1
Specifications and Dimensions
Exhaust Outlet Dimensions and Locations
Models U V W X Y Z
120L/N/E 63.45 in. [1,612
mm]
120S 60.7 in. [1,542
mm]
8.44 in. [214
mm]
8.44 in. [214
mm]
10 in. [254
mm]
10 in. [254
mm]
8.18 in. [208
mm]
8.18 in. [208
mm]
6.82 in. [173
mm]
6.82 in. [173
mm]
8.18 in. [208
mm]
8.18 in. [208
mm]
170 and 200 Series Tumble Dryer Dimensions and Exhaust Outlet Locations
1. Top View of Exhaust Duct
Cabinet Dimensions
Models A B C D E
170L/N/S 33.86 in. [860
mm]
200L/N/S 32.1 in. [815 mm] 35.6 in. [ 904 mm] 55.83 in. [1,418
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
32.5 in. [ 826 mm] 48.33 in. [1,228
mm]
mm]
17 Part No. 70458101ENR10
51.75 in. [1,314
mm]
59.25 in. [1,505
mm]
68.85 in. [1,749
mm]
76.35 in. [1,939
mm]
TMB2255N_SVG
D
B
C
A
B
D
C
A
21
TMB2382N_SVG
A
D
B
C
3
Specifications and Dimensions
Cabinet Dimensions
Models F G H I* J* K*
170L/N/S 53.12 in. [1,349
mm]
200L/N/S 53.12 in. [1,349
mm]
94 in. [2,388
mm]
94 in. [2,388
mm]
75.12 in. [1,908
mm]
75.12 in. [1,908
mm]
48.86 in. [1,241
mm]
48.86 in. [1,241
mm]
50.45 in. [1,281
mm]
50.45 in. [1,281
mm]
62.5 in. [1,588
mm]
62.5 in. [1,588
mm]
* Fire suppression system optional - may not be on machine. Refer to Position and Level the Tumble Dryer to temporarily re-
duce the heights of these models.
Exhaust Outlet Dimensions and Locations
Models V W X Y
170L/N/S 42.38 in. [1,076 mm] 6.75 in. [171 mm] 12 in. [305 mm] 7 in. [178 mm]
200L/N/S 42.38 in. [1076 mm] 6.75 in. [171 mm] 12 in. [305 mm] 7 in. [178 mm]
Electric and Gas Connection Locations for Gas Models Through 3/10/13
1. 120L/N
2. 170L/N
3. 200L/N
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18 Part No. 70458101ENR10
Electrical Connection Gas Connection
TMB2400N_SVG
B
D
D
B
C
C
A
A
21
Specifications and Dimensions
Models
120L/N 18.34 in. [466
170L/N 21 in. [533 mm] 81 in. [2,057 mm] 14.85 in. [377
200L/N 21 in. [533 mm] 81 in. [2,057 mm] 13.7 in. [348 mm] 77.4 in. [1,966
A B C D Diameter
mm]
77.84 in. [1,977
mm]
12.5 in. [318 mm] 70.5 in. [1,791
mm]
77.4 in. [1,966
mm]
mm]
3/4 in. NPT
1 in. NPT
1 in. NPT
mm]
Electric and Gas Connection Locations for Gas Models Starting 3/11/13
1. 120L/N
2. 170L/N and 200L/N
Electrical Connection Gas Connection
Models
120L/N 18.34 in. [466
A B C D Diameter
mm]
170L/N 21 in. [533 mm] 81 in. [2,057 mm] 14.85 in. [377
200L/N 21 in. [533 mm] 81 in. [2,057 mm] 14.85 in. [377
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
77.84 in. [1,977
mm]
12.5 in. [318 mm] 70.5 in. [1,791
1 in. NPT
mm]
77.4 in. [1,966
mm]
mm]
77.4 in. [1,966
mm]
19 Part No. 70458101ENR10
mm]
1 in. NPT
1 in. NPT
TMB2401N_SVG
B2
B2
B1
B1
D
D
E
E
F
F
A2
A2
A1
A1
C
C
21
TMB2383N_SVG
B2
B1
D
3
E
F
A2
A1
C
Specifications and Dimensions
Electric and Steam Connection Locations for Steam Models Through 3/10/13
1. 120S
2. 170S
3. 200S
Steam Inlet
Models
Diameter A1 A2 F
120S 3/4 in. NPT 35.875 in. [911 mm] 13.375 in. [340 mm] 82.75 in. [2,102 mm]
170S 3/4 in. NPT 37.625 in. [956 mm] 15.25 in. [387 mm] 88 in. [2,235 mm]
200S 3/4 in. NPT 37.625 in. [956 mm] 15.25 in. [387 mm] 88 in. [2,235 mm]
Steam Outlet
Models
120S 3/4 in. NPT 34.625 in. [879 mm] 13.125 in. [333 mm] 68.5 in. [1,740 mm]
170S 1 in. NPT 44.625 in. [1,133 mm] 8.75 in. [222 mm] 71.75 in. [1,822 mm]
Diameter B1 B2 D
200S 1 in. NPT 44.625 in. [1,133 mm] 8.75 in. [222 mm] 71.75 in. [1,822 mm]
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20 Part No. 70458101ENR10
Electrical Connection
TMB2401N_SVG
B2
B2
B1
B1
D
D
E
E
F
F
A2
A2
A1
A1
C
C
21
Specifications and Dimensions
Models
C E
120S 18.34 in. [466 mm] 77.84 in. [1,977 mm]
170S 21 in. [533 mm] 81 in. [2,057 mm]
200S 21 in. [533 mm] 81 in. [2,057 mm]
Electric and Steam Connection Locations for Steam Models Starting 3/11/13
1. 120S
2. 170S and 200S
Steam Inlet
Models
Diameter A1 A2 F
120S 3/4 in. NPT 35.875 in. [911 mm] 13.375 in. [340 mm] 82.75 in. [2,102 mm]
170S 3/4 in. NPT 37.625 in. [956 mm] 15.5 in. [394 mm] 87.625 in. [2,226 mm]
200S 3/4 in. NPT 37.625 in. [956 mm] 15.5 in. [394 mm] 87.625 in. [2,226 mm]
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
21 Part No. 70458101ENR10
Specifications and Dimensions
Steam Outlet
Models
Diameter B1 B2 D
120S 3/4 in. NPT 34.625 in. [879 mm] 13.125 in. [333 mm] 68.5 in. [1,740 mm]
170S 1 in. NPT 44.125 in. [1,133 mm] 9 in. [229 mm] 72.125 in. [1,832 mm]
200S 1 in. NPT 44.125 in. [1,133 mm] 9 in. [229 mm] 72.125 in. [1,832 mm]
Electrical Connection
Models
C E
120S 18.34 in. [466 mm] 77.84 in. [1,977 mm]
170S 21 in. [533 mm] 81 in. [2,057 mm]
200S 21 in. [533 mm] 81 in. [2,057 mm]
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
22 Part No. 70458101ENR10
Electric Connection Location for Electric Models
TMB2336N_SVG
A
B
Specifications and Dimensions
Models A B
120E 35.81 in. [910 mm] 85.64 in. [2,175 mm]
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
23 Part No. 70458101ENR10
Installation
Installation
Pre-Installation Inspection
Upon delivery, visually inspect the crate, carton and parts for any
visible shipping damage. If the crate, carton, or cover is damaged
or signs of possible damage are evident, have the carrier note the
condition on the shipping papers before the shipping receipt is
signed, or advise the carrier of the condition as soon as it is discovered.
Remove the crate and protective cover as soon as possible and
check the items listed on the packing list. Advise the carrier of
any damaged or missing articles as soon as possible. A written
claim should be filed with the carrier immediately if articles are
damaged or missing.
IMPORTANT: Remove the shipping tape from the two
back draft dampers located in the exhaust outlet.
IMPORTANT: Warranty is void unless tumble dryer is
installed according to instructions in this manual. Installation should comply with minimum specifications
and requirements detailed in this manual and applicable local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, and any other relevant statutory regulations. Due
to varied requirements, applicable local codes should
be thoroughly understood and all pre-installation work
arranged for accordingly.
Materials Required (Obtain Locally)
All Models One Single Pole fused disconnect switch or
circuit breaker on 1 Phase models.
Circuit breaker on 3 Phase models.
Gas Models One gas shut-off valve for gas service line
to each tumble dryer.
Steam Models One steam shut-off valve for steam service
line to be connected upstream of solenoid
steam valve.
Two steam shut-off valves for each condensate return line.
Table continues...
Materials Required (Obtain Locally)
Flexible steam hoses with a 125 psig
[pounds per square inch gauge] [8.79 kg/sq.
cm] working pressure for connecting steam
coils. Refer to Figure 21 and Figure 22 for
sizing and connection configurations.
Two steam traps for steam coil outlets to
condensate return line.
Optional – Two vacuum breakers for condensate return lines.
IMPORTANT: 3 Phase Only – Each tumble dryer must
be connected to its own individual branch circuit
breaker, not fuses, to avoid the possibility of “single
phasing” and causing premature failure of the motor(s).
Location Requirements
The tumble dryer must be installed on a level floor. Floor covering materials such as carpeting or tile should be removed.
To assure compliance, consult local building code requirements.
The tumble dryer must not be installed or stored in area where it
will be exposed to water and/or weather.
IMPORTANT: DO NOT block the airflow at the rear of
the tumble dryer with laundry or other articles. Doing
so would prevent adequate air supply to the combustion chamber of the tumble dryer.
A typical tumble dryer enclosure is shown in Figure 2 .
IMPORTANT: Install tumble dryers with sufficient clearance for servicing and operation, refer to Figure 2 .
WARNING
To reduce the risk of severe injury, clearance of tumbler cabinet from combustible construction must
conform to the minimum clearances, and/or local codes and ordinances.
W770
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
24 Part No. 70458101ENR10
TMB2020N_SVG
4
3
1
5
6
7
8
2
Installation
NOTE: Shaded areas indicate adjacent structure.
1. 0.5 in. [13 mm] recommended between machines for removal or installation
2. Allow 2-4 in. [51-102 mm] opening at top of machine to aid in removal or installation. A removable trim piece may be used to
conceal the opening; zero clearance allowed for trim.
3. 4 in. [102 mm] maximum header thickness
4. Minimum clearance permitted for remainder:
120 Gas/Electric 4 in. [101.6 mm]
120 Steam 6 in. [152.4 mm]
170/200 Gas 4 in. [101.6 mm]
170/200 Steam 8 in. [203.2 mm]
5. Guard
6. Provision for make-up air
7. 24 in. [610 mm] minimum, 36 in. [914 mm] recommended for maintenance purposes
8. 0.25 in. [6 mm] recommended for removal or installation purposes, zero clearance allowed
Figure 2
Level the tumble dryer to within 0.125 inch [3 mm] from front-
Position and Level the Tumble Dryer
to-rear (level on cylinder rib), and side-to-side (level on top panel). Shim under corners to level and stabilize unit. Tumble dryer
The tumble dryer may be moved with or without the skid. To remove the skid, unscrew the four shipping bolts, and discard them.
To fit a 170 and 200 series tumble dryer (with shipping skid)
must not rock.
Mounting
through a 8 foot [2.43 meters] high door, you must remove the
front access panel. The upper 3 inches [76 mm] of the stove must
also be removed on 170 series gas tumble dryers. Removing the
entire gas or steam heater assembly and the shipping skid, will reduce the height of the 120 series tumble dryer to 70 inches [1,778
Where local code requires the unit to be securely mounted, use
the shipping bolt frame holes found on the tumble dryer frame.
Use either epoxy 1/2 in. [13 mm] bolts or equivalent 1/2 in. [13
mm] concrete anchors, such as expandable bolts.
mm], and the 170 and 200 series tumble dryer to 75 inches [1,905
mm].
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
25 Part No. 70458101ENR10
Installation
Fire Suppression System (Optional
Equipment)
WARNING
Electrical shock can result in death or serious injury.
If the water dispensing system is activated, do not
attempt to operate the tumble dryer. If the water dispensing system is activated, have the tumble dryer
inspected by a qualified agency before operating the
tumble dryer.
Check Local Codes and Permits
Call your local water company or the proper municipal authority
for information regarding local codes.
IMPORTANT: It is your responsibility to have ALL
plumbing connections made by a qualified professional to assure that the plumbing is adequate and conforms to local, state, and federal regulations or codes.
IMPORTANT: It is the installation or owner’s responsibility to see that the necessary or required water, water
pressure, pipe size, or connections are provided. Manufacturer assumes no responsibility if the fire suppression system is not connected, installed, or maintained
properly.
Water Requirements
W879
and a maximum of 120 psi [827 kPa] of pressure at all times.
Flowrate must be no less than, but approximately 15 gallons [57
liters] per minute.
NOTE: Water pressure under 20 psi [138 kPa] will
cause low flow and water leakage at water solenoid
valve.
If the rear of the tumble dryer or the water supply is located in an
area where it will be exposed to cold/freezing temperatures, pro-
visions must be made to protect these water lines from freezing.
IMPORTANT: Temperature of the water supply must be
kept between 40°F and 120°F [4.4°C and 48.9°C] . If wa-
ter in the supply line or water solenoid valve freezes,
the fire suppression system will not operate.
IMPORTANT: If temperature sensors inside the tumble
dryer register a temperature below 40F° [4.4°C] , the
fire suppression system control will lock out. This fea-
ture protects against operation of the tumble dryer with
a possible frozen water supply. Only when the temper-
ature sensors register a temperature above 40F°
[4.4°C] will the machine reset for operation.
IMPORTANT: Flexible supply line/coupling must be
used. Solenoid valve failure due to hard plumbing con-
nections will void the warranty. It is recommended that
a filter or strainer be installed in the water supply line.
Water Connections
Connect machine to a backflow preventer (vacuum breaker) be-
fore connecting to the public water main in all countries where
local regulations require specific water approval certificates.
IMPORTANT: Water must be supplied to the fire suppression system, or the fire suppression system will
not operate as intended.
Connection point to the electric water solenoid valve is a 3/4 inch
[19 mm] hose. The fire suppression system equipped tumble dryer must be supplied with a minimum water pipe size of 1/2 inch
[12.7 mm] and be provided with a minimum of 20 psi [138 kPa]
Two hoses and a Y-valve are provided with the tumble dryer to
allow for connection of water supply to tumble dryer. The water
connections are made to the bushings of the water solenoid valve,
located on the rear of the tumble dryer. The Y-valve provides a
single female hose connection (Standard US 3/4-11 1/2 NH
thread). Refer to Figure 3 and Figure 4 .
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
26 Part No. 70458101ENR10
TMB2012N_SVG
2
1
3
3
170/200
120
1. Fire Suppression System Control Box
TMB2008N_SVG
3
2
4
5
2
1
2. Water Solenoid Valve
3. Opening for Auxiliary Alarm Cable
Installation
To connect the two hoses (supplied with tumble dryer), insert
rubber washers (from literature pack) in water inlet hose couplings. Refer to Figure 4 .
1. Lock
2. Hose Couplings
3. Y Valve
4. Inlet Hoses
5. Opening for Auxiliary Alarm Cable
Figure 4
Connect inlet hoses to water supply. Flush the lines for approximately two minutes to remove any foreign materials that could
clog the screens in the water mixing valve. This is especially important when installing a tumble dryer in a newly constructed or
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
Figure 3
renovated building. Then connect the hoses to the Y-valve; con-
nect the Y-valve to the connections at the rear of the tumble dry-
er.
IMPORTANT: Thread hose couplings onto valve con-
nections finger tight, then turn 1/4 turn with pliers. Do
not cross thread or overtighten couplings.
IMPORTANT: Hoses and other natural rubber parts de-
teriorate after extended use. Hoses may develop
cracks, blisters or material wear from the temperature
and constant high pressure they are subjected to. All
hoses should be checked on a yearly basis for any visi-
ble signs of deterioration. Any hose showing the signs
of deterioration listed above should be replaced imme-
diately. All hoses should be replaced every five years.
NOTE: Longer inlet hoses are available (as optional
equipment at extra cost) if the hoses supplied with the
tumble dryer are not long enough for installation. Order
hoses as follows:
Part No. 20617 Inlet hose 8 feet [2.44 m]
Part No. 20618 Inlet hose 10 feet [3.05 m]
NOTE: Replacement outlet hoses are available (at extra
cost). Order 44073302 Hose, 21 in. [53 cm ] for 120 ser-
ies and 44073303, 31 in. [79 cm] for 170 and 200 series.
27 Part No. 70458101ENR10
Loading...