Alliance Laundry Systems 9001014R7 User Manual

Washer-Extractors

Cabinet Freestanding

Basic Installation/Operation

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

Part No. 9001014R7

June 2010

Basic Installation/Operation

Table of

Contents

Introduction......................................................................................... 2

Model Identification ............................................................................. 2

Safety Information .............................................................................. 3

Explanation of Safety Messages........................................................... 3

Important Safety Instructions ............................................................... 3

Safety Decals ........................................................................................ 5

Operator Safety..................................................................................... 6

Specifications and Dimensions........................................................... 7

Installation........................................................................................... 22

Dimensional Clearances................................................................... 22

Machine Foundation ........................................................................ 23

Mechanical Installation......................................................................... 24

Frame Dimensions and Mounting Bolt Location

for 18, 25, 33, 35, 40, 55, 75, 100, 135, 165 and 200 Models........ 24

Mounting Bolt Installation (If Required).............................................. 27

Electrical Specifications ....................................................................... 28

Operation............................................................................................. 30

Control Identification............................................................................ 30

Load the Machine ................................................................................. 31

Disposal of Unit................................................................................... 32

means without the expressed written consent of the publisher.

9001014

1

Basic Installation/Operation

Introduction

Model Identification

Information in this manual is applicable to these models:

HX18PV HX100PV SX25PV SX135PV UX33PV UX100PV

HX25PV HX135PV SX35PV SX165PV UX35PV UX135PV

HX35PV HX165PV SX55PV SX200PV UX40PV UX165PV

HX55PV HX200PV SX75PV UX18PV UX55PV UX200PV

HX75PV SX18PV SX100PV UX25PV UX75PV

2

9001014

Safety Information

DANGER indicates the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the danger is ignored.

DANGER

WARNING indicates the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

WARNING

CAUTION indicates the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

CAUTION

To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer, follow these basic precautions:

W023

WARNING

Basic Installation/Operation

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine.

Important Safety Instructions

1. Read all instructions before using the washer.

2. Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION manual for the proper grounding of the washer.

3. Do not wash textiles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed.

NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.

5. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. The gas is flammable, do not smoke or use an open flame during this time.

6. Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. This is a safety rule for all appliances.

7. Before the washer is removed from service or discarded, remove the door to the washing compartment.

8. Do not reach into the washer if the wash drum is moving.

9001014

3

Basic Installation/Operation

9. Do not install or store the washer where it will be exposed to water and/or weather.

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions that the user understands and has the skills to carry out.

12. To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the washer to the electrical power source.

13. Use washer only for its intended purpose, washing textiles.

14. Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket.

15. ALWAYS disconnect the washer from electrical supply before attempting any service. Disconnect the power cord by grasping the plug, not the cord.

16. Install the washer according to the INSTALLATION INSTRUCTIONS. All connections for water, drain, electrical power and grounding must comply with local codes and be made by licensed personnel when required.

17. To reduce the risk of fire, textiles which have traces of any flammable substances such as vegetable oil, cooking oil, machine oil, flammable chemicals, thinner, etc., or anything containing wax or chemicals such as in mops and cleaning cloths, must not be put into the washer. These flammable substances may cause the fabric to catch on fire by itself.

20. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

21. Be sure water connections have a shut-off valve and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day.

22. Loading door MUST BE CLOSED any time the washer is to fill, tumble or spin. DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open.

23. Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times (preferably in a locked cabinet).

24. Always follow the fabric care instructions supplied by the textile manufacturer.

25. Never operate the washer with any guards and/or panels removed.

26. DO NOT operate the washer with missing or broken parts.

27. DO NOT bypass any safety devices.

28. Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.

NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer.

18. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

19. Keep washer in good condition. Bumping or dropping the washer can damage safety features. If this occurs, have washer checked by a qualified service person.

4

Any problems or conditions not understood should be reported to the dealer, distributor, service agent or the manufacturer.

9001014

IMPORTANT: Ensure that the recommended

This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty.

SW004

WARNING

Install the machine on a level floor of sufficient strength. Failure to do so may result in conditions which can produce serious injury, death and/or property damage.

W703

WARNING

Be careful around the open door, particularly when loading from a level below the door. Impact with door edges can cause personal injury.

SW025

CAUTION

Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot and will cause severe burns. The steam must be turned off and the pipe, connections, and components allowed to cool before the pipe can be touched.

SW014

WARNING

clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

Basic Installation/Operation

Safety Decals

Safety decals appear at crucial locations on the machine. Failure to maintain legible safety decals could result in injury to the operator or service technician.

To provide personal safety and keep the machine in proper working order, follow all maintenance and safety procedures presented in this manual. If questions regarding safety arise, contact the manufacturer immediately.

Use manufacturer-authorized spare parts to avoid safety hazards.

9001014

5

Basic Installation/Operation

NEVER insert hands or objects into basket until it has completely stopped. Doing so could result in serious injury.

SW012

WARNING

Never operate the machine with a bypassed or disconnected balance system. Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage.

SW039

WARNING

Operator Safety

To ensure the safety of machine operators, the following maintenance checks must be performed daily:

1. Prior to operating the machine, verify that all warning signs are present and legible. Missing or illegible signs must be replaced immediately. Make certain that spares are available.

2. Check door interlock before starting operation of the machine:

a.Attempt to start the machine with the door

open. The machine should not start with the door open.

b.Close the door without locking it and attempt to

start the machine. The machine should not start with the door unlocked.

Do not bypass any safety devices in the machine.

c.Close and lock the door and start a cycle.

Attempt to open the door while the cycle is in progress. The door should not open.

If the door lock and interlock are not functioning properly, call a service technician.

3. Do not attempt to operate the machine if any of the following conditions are present:

a.The door does not remain securely locked

during the entire cycle.

b.Excessively high water level is evident.

c.Machine is not connected to a properly

grounded circuit.

6

9001014

Specifications and Dimensions

General Specifications

Model 1825333540

Overall Dimensions

Overall width 660 mm

(26 in.)

Overall height 1031 mm

(40.6 in.)

Overall depth 780 mm

(30.7 in.)

Weight and Shipping Information

Net weight †

211 kg

(465 lb.)

Net weight †† 236 kg

(520 lb.)

Shipping weight † 233 kg

(514 lb.)

Shipping weight †† 283 kg

(624 lb.)

Shipping volume 0.8 m

3

(22.5 ft.3)

Wash Cylinder Information

Cylinder diameter 530 mm

(20.9 in.)

Cylinder depth 345 mm

(13.6 in.)

Cylinder volume 76 l

3

(2.7 ft.

)

Perforation size 3 mm

(0.1 in.)

Door Opening Information

Door opening size

300 mm

(11.8 in.)

Height of door bottom above floor

279 mm

(11 in.)

† For Models with A or M in the 8th position in the model number (e.g. *X18PVXA6)

†† For Models with U in the 8

th

position in the model number (e.g *X18PVXU6)

660 mm

(26 in.)

1031 mm (40.6 in.)

870 mm

(34.3 in.)

236 kg

(520 lb.)

241 kg

(531 lb.)

258 kg

(569 lb.)

290 kg

(639.5 lb.)

3

0.9 m

(24.5 ft.3)

530 mm

(20.9 in.)

440 mm

(17.3 in.)

97 l

(3.43 ft.3)

3 mm

(0.1 in.)

300 mm

(11.8 in.)

279 mm

(11 in.)

(continued)

780 mm

(30.71 in.)

1376 mm

(54.15 in.)

840 mm

(33.07 in.)

368 kg

(811.30 lb.)

N/A

383 kg

(844.37 lb.)

N/A

1.21 m

(42.83 ft.3)

680 mm

(26.77 in.)

400 mm

(15.75 in.)

145 l

(5.12 ft.3)

3 mm

(0.1 in.)

400 mm

(15.75 in.)

472 mm

(18.58 in.)

Basic Installation/Operation

783 mm

(30.8 in.)

1194 mm

(47 in.)

960 mm

(37.8 in.)

358 kg

(789 lb.)

347 kg

(765 lb.)

388 kg

(855 lb.)

467 kg

(1030 lb.)

3

1.3 m

3

(34.7 ft.3)

650 mm

(25.6 in.)

500 mm

(19.7 in.)

167 l

(5.9 ft.3)

3 mm

(0.1 in.)

300 mm

(11.8 in.)

395 mm

(15.6 in.)

780 mm

(30.71 in.)

1376 mm

(54.15 in.)

940 mm

(37.01 in.)

391 kg

(862.01 lb.)

N/A

418 kg

(921.53 lb.)

N/A

3

1.3 m

(45.98 ft.3)

680 mm

(26.77 in.)

500 mm

(19.69 in.)

181 l

(6.39 ft.3)

3 mm

(0.1 in.)

400 mm

(15.75 in.)

472 mm

(18.58 in.)

9001014

7

Basic Installation/Operation

(continued)

General Specifications

Model 1825333540

Drive Train Information

Number of motors in drive train 11111

Drive motor power 0.75 kW

(1 HP)

0.75 kW (1 HP)

2.2 kW

(2.95 HP)

1.5 kW (2 HP)

2.2 kW

(2.95 HP)

Cylinder Speeds

Wash/reverse speed 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM

Distribution/drain speed 82 RPM 82 RPM 85 RPM 74 RPM 85 RPM

Extract speed 250-1000 RPM 250-1000 RPM 250-1000 RPM 250-1000 RPM 250-1000 RPM

Centrifugal Force Data

Wash/reverse centrifugal force 0.03-0.74 Gs 0.03-0.74 Gs 0.37-0.94 Gs 0.04-0.91 Gs 0.37-0.94 Gs

Extract centrifugal force 19-296 Gs 19-296 Gs 24-377 Gs 23-363 Gs 24-377 Gs

Balance Detection

Vibration safety switch installed Standard Standard Standard Standard Standard

Direct Steam Heating (Optional)

Steam inlet connection size 10 mm

(0.38 in.)

10 mm

(0.38 in.)

10 mm

(0.375 in.)

10 mm

(0.38 in.)

10 mm

(0.375 in.)

Number of steam inlets 11111

Electrical Heating (Optional)

Total electrical heating capacity 9 kW 9 kW 18 kW 18 kW 18 kW

Electrical heating elements 33666

Electrical heat element size 3 kW 3 kW 3 kW 3 kW 3kW

8

9001014

Model 55 75 100 135 165 200

Overall Dimensions

Basic Installation/Operation

General Specifications

Overall width 900 mm

(35.4 in.)

Overall height 1544 mm

(60.8 in.)

Overall depth 1016 mm

(40 in.)

Weight and Shipping Information

Net weight 570 kg

(1247 lb.)

Shipping weight 630 kg

(1380 lb.)

Shipping volume 1.5 m

3

(54.9 ft.3)

Wash Cylinder Information

Cylinder diameter 750 mm

(29.5 in.)

Cylinder depth 530 mm

(20.9 in.)

Cylinder volume 234 l

(8.27 ft.

3

)

1060 mm (41.8 in.)

1560 mm (61.4 in.)

1168 mm

(46 in.)

865 kg

(1907 lb.)

995 kg

(2194 lb.)

3

2.1 m

(74 ft.3)

850 mm

(33.5 in.)

537 mm

(21.1 in.)

305 l

(10.76 ft.3)

1200 mm (47.3 in.)

1920 mm (75.6 in.)

1330 mm (52.4 in.)

1520 kg

(3351 lb.)

1697 kg

(3741 lb.)

3

3.3 m

(115 ft.3)

980 mm

(38.6 in.)

597 mm

(23.5 in.)

451 l

(15.92 ft.3)

1200 mm (47.3 in.)

1920 mm (75.6 in.)

1500 mm (59.1 in.)

1645 kg

(3626 lb.)

1822 kg

(4017 lb.)

3

3.7 m

(131 ft.3)

980 mm

(38.6 in.)

775 mm

(30.5 in.)

585 l

(20.66 ft.3)

1300 mm (51.8 in.)

2100 mm (82.7 in.)

1620 mm (63.8 in.)

2100 kg

(4630 lb.)

2319 kg

(5113 lb.)

3

4.4 m

(162 ft.3)

1095 mm (43.1 in.)

775 mm

(30.5 in.)

730 l

(25.8 ft.3)

1300 mm (51.8 in.)

2100 mm

(82.68 in.)

1808 mm

(71.18 in.)

2900 kg

(6393.41 lb.)

3000 kg

(6613.86 lb.)

3

6.17 m

(217.89 ft.3)

1095 mm (43.1 in.)

957 mm

(37.68 in.)

930 l

(31.748 ft.3)

Perforation size 3 mm

(0.1 in.)

Door Opening Information

Door opening size

395 mm

(15.6 in.)

Height of door bottom above floor

559 mm

(22 in.)

3 mm

(0.1 in.)

395 mm

(15.6 in.)

559 mm

(22 in.)

(continued)

3 mm

(0.1 in.)

500 mm

(19.7 in.)

648 mm

(25.5 in.)

3 mm

(0.1 in.)

500 mm

(19.7 in.)

648 mm

(25.5 in.)

3 mm

(0.1 in.)

622 mm

(24.5 in.)

710 mm

(28 in.)

3 mm

(0.1 in.)

622 mm

(24.5 in.)

603 mm

(23.74 in.)

9001014

9

Basic Installation/Operation

(continued)

General Specifications

Model 55 75 100 135 165 200

Drive Train Information

Number of motors in drive train 1 1 1 1 1 1

Drive motor power 3 kW

(4 HP)

4 kW

(5.4 HP)

5.5 kW

(7.4 HP)

7.5 kW

(10 HP)

11.5 kW (15 HP)

15 kW

(20 HP)

Cylinder Speeds

Wash/reverse speed 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM 10-50 RPM

Distribution/drain speed 69 RPM 65 RPM 61 RPM 61 RPM 100 RPM 80 RPM

Extract speed 250-1000

RPM

250-1000

RPM

250-800

RPM

250-800

RPM

250-750

RPM

250-750

RPM

Centrifugal Force Data

Wash/reverse centrifugal force 0.04-1.05 Gs0.05-1.19 Gs0.06-1.37 Gs0.06-1.37 Gs0.06-1.52 Gs0.06-1.52

Gs

Extract centrifugal force 26-418 Gs 30-475 Gs 34-350 Gs 34-350 Gs 34-344 Gs 34-342 Gs

Balance Detection

Vibration safety switch installed Standard Standard Standard Standard Standard Standard

Direct Steam Heating (Optional)

Steam inlet connection size 10 mm

(0.38 in.)

10 mm

(0.38 in.)

10 mm

(0.38 in.)

10 mm

(0.38 in.)

10 mm

(0.38 in.)

19 mm

(0.75 in.)

Number of steam inlets 1 1 1 1 1 1

Electrical Heating (Optional)

Total electrical heating capacity 18 kW 18 kW 27 kW 27 kW N/A 36 kW

Electrical heating elements 6 6 9 9 N/A 9

Electrical heat element size 3 kW 3 kW 3 kW 3 kW N/A 4 kW

10

9001014

Basic Installation/Operation

CFD530 N

CFS464N

CFS465N

18 AND 25 POUND CAPACITY MODELS WITH U IN THE 8TH POSITION (E.G. *X18PVXU6)

1031 mm

(40.6 in.)

518 mm

(20.4 in.)

660 mm

(26 in.)

CFD530N

CFS464N

CFS465N

229 mm

(9 in.)

152 mm

(6 in.)

74 mm

(2.9 in.)

140 mm

(5.5 in.)

780 mm

(30.7 in.)

742 mm

(29.2 in.)

41 mm

(1.6 in.)

389 mm

(15.3 in.)

158 mm (6.2 in.)

51 mm

(2 in.)

181 mm

(7.1 in.)

1

4

6

3

2

10

279 mm

(11 in.)

18: 787 mm (31 in.)

25: 884 mm (34.8 in.)

881 mm

(34.7 in.)

7

9

5

486 mm

(19.13 in.)

18: 560 mm

(22.05 in.)

25: 660 mm

(25.98 in.)

8

1011 mm (39.8 in.)

Figure 1

1 Fill and Supply Ventilation 6 External Liquid Supply Inlets 2 Cold Water Inlet (Required) 7 Electrical Power Input 3 Hot Water Inlet (Required) 8 External Supply Signal Input 4 Cold Water Inlet (Required) 9 Drain Outlet 5 Flushing Supply Dispenser 10 Steam Connection Input (Optional)

9001014

11

Basic Installation/Operation

CFD521N

CFD522N

1038 mm (40.87 in.)

1011 mm (39.8 in.)

279 mm

(10.98 in.)

530 mm (20.87 in.)

65 mm

(2.56 in.)

660 mm (25.98 in.)

65 mm

(2.56 in.)

887 mm (34.92 in.)

791 mm (31.14in.)

485 mm (19.1 in.)

70 mm (2.76 in.)

44. mm

(1.73 in.)

180 mm (7.09 in.)

660 mm (25.98 in.)

11

10

4

2

1

9

33 mm

(1.3 in.)

18: 590 mm (23.23 in.) 25: 690 mm (27.16 in.)

747 mm (29.41 in.)

8

3

33 mm

(1.3 in.)

30 mm

(1.18 in.)

220 mm

(8.66 in.)

7

CFD521N

18: 670 mm (26.38 in.) 25: 770 mm (30.31 in.)

18: 727 mm (28.62 in.) 25: 827 mm (32.56 in.)

30 mm

(1.18 in.)

696,2 mm (27.41 in.)

109 mm

(4.3 in.)

226 mm (8.9 in.)

151 mm (5.94 in.)

75 mm (2.95 in.)

65 mm

(2.72 in.)

CFD522N

6

5

18 AND 25 POUND CAPACITY MODELS WITH A OR M IN THE 8TH POSITION (E.G. *X18PVXM6)

CFD528N

1 Fill and Supply Ventilation 7 Electrical Power Input 2 Cold Water Inlet (Required) 8 Drain Outlet 3 External Liquid Supply Inlets 9 Steam Connection Input (Optional) 4 Hot Water Inlet (Required) 10 Cold Water Inlet (Required) 5 Ventilation Tub 11 Flushing Supply Dispenser 6 Main Switch

Figure 2

12

9001014

Basic Installation/Operation

CFD539N

CFD538N

1376 mm (54.15 in.)

1348 mm (53.07 in.)

472 mm (18.58 in.)

680 mm (26.77 in.)

50 mm

(1.97 in.)

780 mm (30.71 in.)

50 mm

(1.97 in.)

1141 mm (44.9 in.)

1108 mm (43.6 in.)

704 mm (27.7 in.)

185 mm (7.29 in.)

170 mm (6.69 in.)

3

2

1

10

665 mm (26.18 in.)

1066 mm (41.95 in.)

9

4

86.5 mm (3.41 in.)

220 mm (8.66 in.)

7

CFD537N

34 mm

(1.34 in.)

1015 mm (39.96 in.)

1.38 in.

(35 mm)

332 mm (13.05 in.) 267 mm (10.49 in.)

202 mm (7.93 in.)

4.3 in.

(109 mm)

CFD538N

6

5

33 MODEL

88 mm

(3.47 in.)

34 mm

(1.34 in.)

733 mm (28.86 in.)

753 mm (29.65 in.)

105 mm (4.13 in.)

8

CFD537N

9001014

1 Fill and Supply Ventilation 6 Connection Clamps 2 External Liquid Supply Inlets 7 Ventilation Tub 3 Cold Water Inlet (Required) 8 Electrical Power Inputs 4 Cold Water Inlet (Required) 9 Drain Valve 5 Hot Water Inlet (Required) 10 Steam Connection Input (Optional)

Figure 3

13

Basic Installation/Operation

CFD531N

CFS467N

CFD531N

CFS467N

119 4 m m

(47 in.)

620 mm

(24.4 in.)

782 mm

(30.8 in.)

CFS468N

328 mm

(12.9 in.)

264 mm

(10.4 in.)

934 mm

(36.75 in.)

960 mm

(37.8 in.)

155 mm

(6.1 in.)

889 mm

(35 in.)

203 mm

(8 in.)

1001 mm

(39.4 in.)

112 mm

(4.4 in.)

394 mm

(15.5 in.)

5

508 mm

(20 in.)

965 mm

(38 in.)

1041 mm

(41 in.)

89 mm

(3.5 in.)

1

3

2

4

8

7

9

10

6

639 mm

(25.16 in.)

770 mm

(30.31 in.)

35 POUND CAPACITY MODELS WITH U IN THE 8TH POSITION (E.G. *X35PVXU6)

1176 mm (46.3 in.)

1 Fill and Supply Ventilation 6 External Liquid Supply Inlets 2 Cold Water Inlet (Required) 7 Electrical Supply Signal Input 3 Hot Water Inlet (Required) 8 External Supply Signal Input 4 Cold Water Inlet (Required) 9 Drain Outlet 5 Flushing Supply Dispenser 10 Steam Connection Input (Optional)

Figure 4

14

9001014

Basic Installation/Operation

CFD524N

CFD525N

CFD529N

CFD524N

CFD525N

1202 mm (47.32 in.)

1176 mm (46.3 in.)

66 mm

(2.6 in.)

CFD529N

34 mm

(1.34 in.)

267 mm (10.49 in.)

893 mm (35.16 in.)

88 mm

(3.47 in.)

332 mm (13.05 in.)

530 mm (20.87 in.)

200 mm

(7.87 in.)

70 mm (2.76 in.)

843 mm (33.17 in.)

376 mm

(14.78 in.)

11

60 mm

(2.36 in.)

935 mm (36.81 in.)

968 mm (38.11 in.)

202 mm (7.93 in.)

1

3

2

4

7

9

10

6

648 mm (25.51 in.)

36.5 mm (1.44 in.)

35 POUND CAPACITY MODELS WITH A OR M IN THE 8TH POSITION (E.G.. *X35PVXM6)

780 mm (30.71 in.)

66 mm

(2.6 in.)

34 mm

(1.34 in.)

220 mm (8.66 in.)

36.5 mm (1.44 in.)

765 mm (30.12 in.)

860 mm (33.86 in.)

916 mm (36.06 in.)

82 mm

(3.23 in.)

105 mm (4.13 in.)

109.2 mm (4.3 in.)

8

5

35 mm (1.38 in.)

1 Fill and Supply Ventilation 7 Drain Outlet 2 Hot Water Inlet (Required) 8 Steam Connection Input (Optional) 3 Cold Water Inlet (Required) 9 External Liquid Supply Inlets 4 Main Switch 10 Cold Water Inlet (Required) 5 Ventilation Tub 11 Flushing Supply Dispenser 6 Electrical Power Input

9001014

Figure 5

15

Basic Installation/Operation

CFD539N

CFD537N

CFD538N

1376 mm (54.15 in.)

1348 mm (53.07 in.)

472 mm (18.58 in.)

680 mm (26.77 in.)

50 mm

(1.97 in.)

780 mm (30.71 in.)

50 mm

(1.97 in.)

1141 mm (44.9 in.)

1108 mm (43.6 in.)

704 mm (27.7 in.)

185 mm (7.29 in.)

170 mm (6.69 in.)

3

2

1

10

765 mm (30.12 in.)

1066 mm (41.95 in.)

9

4

86.5 mm (3.41 in.)

220 mm

(8.66 in.)

7

CFD537N

34 mm

(1.34 in.)

1015 mm (39.96 in.)

35 mm

(1.38 in.)

332 mm (13.05 in.) 267 mm (10.49 in.)

202 mm (7.93 in.)

109 mm

(4.3 in.)

CFD538N

6

5

40 MODEL

88 mm

(3.47 in.)

34 mm

(1.34 in.)

833 mm (32.8 in.)

853 mm (33.58 in.)

105 mm (4.13 in.)

8

1 Fill and Supply Ventilation 6 Connection Clamps 2 External Liquid Supply Inlets 7 Ventilation Tub 3 Cold Water Inlet (Required) 8 Electrical Power Inputs 4 Cold Water Inlet (Required) 9 Drain Valve 5 Hot Water Inlet (Required) 10 Steam Connection Input (Optional)

Figure 6

16

9001014

Basic Installation/Operation

CFD509N

CFS470N

&)61

CFD509N

1544 mm

(60.8 in.)

859 mm

(33.8 in.)

900 mm

(35.43 in.)

1499 mm

(59 in.)

CFS470N

1016 mm

(40 in.)

CFS471N

55 MODEL

158 mm

(6.2 in.)

254 mm

(10 in.)

91 mm

(13.6 in.)

99 mm

(3.9 in.)

191 mm (7.5 in.)

165 mm

(6.5 in.)

104 mm

(4.1 in.)

1389 mm (54.7 in.)

721 mm

(28.4 in.)

36 mm

(1.4 in.)

1

3

4

9

11

559 mm

(22 in.)

5

2

104 mm

(4.1 in.)

165 mm

(6.5 in.)

1283 mm

(50.5 in.)

8

7

10

102 mm

(4 in.)

6

252 mm

(9.9 in.)

740 mm

(29.13 in.)

830 mm

(32.68 in.)

1 Fill and Supply Ventilation 7 Electrical Power Input 2 Cold Water Inlet (Required) 8 External Supply Signal Input 3 Hot Water Inlet (Required) 9 Drain Outlet 4 Cold Water Inlet (Required) 10 Reuse Drain Outlet (Optional) 5 Flushing Supply Dispenser 11 Steam Connection Input (Optional) 6 External Liquid Supply Inlets

Figure 7

9001014

17

Basic Installation/Operation

&)61

CFD510N

CFS473N

CFD510N

1575 mm

(62 in.)

853 mm

(33.6 in.)

1532 mm

(60.3 in.)

116 8 m m

(46 in.)

CFS473N

CFS474N

75 MODEL

229 mm

(9 in.)

488 mm

(19.2 in.)

94 mm

(3.7 in.)

175 mm

(6.9 in.)

170 mm

(6.7 in.)

104 mm

(4.1 in.)

1407 mm

(55.4 in.)

582 mm

(22.9 in.)

43 mm

(1.7 in.)

2

3

4

9

11

5

102 mm

(4 in.)

559 mm

(22 in.)

1060 mm

(41.73 in.)

1

7

8

104 mm

(4.1 in.)

10

246 mm

(9.7 in.)

6

1315 mm

(51.75 in.)

870 mm

(34.25 in.)

960 mm

(37.8 in.)

366 mm

(14.4 in.)

1 Fill and Supply Ventilation 7 Electrical Power Input 2 Cold Water Inlet (Required) 8 External Supply Signal Input 3 Hot Water Inlet (Required) 9 Drain Outlet 4 Cold Water Inlet (Required) 10 Reuse Drain Outlet (Optional) 5 Flushing Supply Dispenser 11 Steam Connection Input (Optional) 6 External Liquid Supply Inlets

Figure 8

18

9001014

Basic Installation/Operation

CFD511N

CFS476N

CFD511N

1951 mm (76.8 in.)

960 mm

(37.8 in.)

1040 mm

(40.94 in.)

1200 mm

(47.24 in.)

CFS476N

100: 1331 mm (52.4 in.) 135: 1506 mm (59.3 in.)

CFS477N

305 mm

(12 in.)

2362 mm

(9.3 in.)

175 mm

(6.9 in.)

104 mm (4.1 in.)

114 mm (4.5 in.)

165 mm

(6.5 in.)

221 mm

(8.7 in.)

170 mm

(6.7 in.)

51 mm

(2 in.)

249 mm (9.8 in.)

696 mm

(27.4 in.)

216 mm

(8.5 in.)

216 mm

(8.5 in.)

185 mm

(7.3 in.)

6

648 mm

(25.5 in.)

102 mm

(4 in.)

89 mm

(3.5 in.)

1575 mm

(62 in.)

12

2

3

5

4

1

9

13

8

10

11

7

100: 1010 mm

(39.76 in.)

135: 1185 mm

(46.65 in)

100 AND 135 MODELS

1 Fill and Supply Ventilation 8 Electrical Power Input 2 Cold Water Inlet (Required) 9 External Supply Signal Input 3 Hot Water Inlet (Required) 10 Drain Outlet 4 Cold Water Inlet (Required) 11 Reuse Drain Outlet (Optional) 5 Cold Water Inlet (Required) 12 Steam Connection Input (Optional) 6 Flushing Supply Dispenser 13 Service Power Disconnect 7 External Liquid Supply Inlets

Figure 9

9001014

19

Basic Installation/Operation

CFD511N

2100 mm

(82.7 in.)

1020 mm (40.2 in.)

114 0 m m (44.9 in.)

1300 mm (51.2 in.)

CFS477N

360 mm

(14.25 in.)

273 mm

(10.75 in.)

198 mm (7.8 in.)

114 mm (4.5 in.)

172 mm

(6.75 in.)

221 mm (8.7 in.)

197 mm

(7.75 in.)

51 mm

(2 in.)

260 mm

(10.24 in.)

696 mm

(27.4 in.)

254 mm

(10 in.)

6

641 mm

(25.25 in.)

122 mm

(4.8 in.)

1854 mm

(73 in.)

12

2

3

5

4

1

9

13

8

10

11

7

254 mm

(10 in.)

CFD15N

1620 mm

(63.8 in.)

102 mm

(4 in.)

118 5 m m

(46.7 in.)

165 MODEL

236 mm (9.3 in.)

1 Fill and Supply Ventilation 8 Electrical Power Input 2 Cold Water Inlet (Required) 9 External Supply Signal Input 3 Hot Water Inlet (Required) 10 Drain Outlet 4 Cold Water Inlet (Required) 11 Reuse Drain Outlet (Optional) 5 Cold Water Inlet (Required) 12 Steam Connection Input (Optional) 6 Flushing Supply Dispenser 13 Service Power Disconnect 7 External Liquid Supply Inlets

20

Figure 10

9001014

CFD533N

2100 mm

(82.7 in.)

993 mm

(39 in.)

1138 mm (44.8 in.)

CFD535N

81 mm

(3.19 in.)

1300 mm (51.18 in.)

323 mm

(12.72 in.)

248 mm

(9.76 in.)

257 mm

(10.12 in.)

486 mm

(19.13 in.)

899.5 mm (35.37 in.)

6

603 mm

(23.75 in.)

408 mm

(16.06 in.)

12

2

3

5

4

1

9

13

8

10

11

7

CFD534N

44 mm

(1.73 in.)

175.2 mm (68.96 in.)

260 mm

(10.24 in.)

260 mm

(10.24 in.)

81 mm

(3.19 in.)

169.5 mm (6.67 in.)

173 mm

(6.81 in.)

237 mm

(9.33 in.)

117 mm

(4.61 in.)

262 mm

(10.31 in.)

117 mm

(6.97 in.)

81 mm

(3.19 in.)

1453 mm (57.2 in.)

1365 mm (53.74 in.)

26.5 mm

(1.04 in.)

44 mm

(1.73 in.)

272 mm

(10.71 in.)

56.5 mm (2.23 in.)

174 mm (6.85 in.)

200 MODEL

Basic Installation/Operation

1 Fill and Supply Ventilation 8 Electrical Power Input 2 Cold Water Inlet (Required) 9 External Supply Signal Input 3 Hot Water Inlet (Required) 10 Drain Outlet (Standard) 4 Cold Water Inlet (Required) 11 Dual Drain Outlet (Optional) 5 Cold Water Inlet (Required) 12 Steam Connection Input (Optional) 6 Flushing Supply Dispenser 13 Service Power Disconnect 7 External Liquid Supply Inlets

Figure 11

9001014

21

Basic Installation/Operation

Installation

Dimensional Clearances

Table 1 shows recommended minimum clearances on all sides of the washer-extractor.

Recommended Minimum Clearances

Model 18 25 33 35 40 55 75 100 135 165 200

Minimum rear clearance

Minimum clearance between machine and wall

Minimum clearance between machines (side)

Minimum front clearance (door swing)

600 mm

(24 in.)

150 mm

(6 in.)

25.4 mm (1 in.)

419 mm

(16.5 in.)

600 mm

(24 in.)

150 mm

(6 in.)

25.4 mm (1 in.)

419 mm

(16.5 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

533 mm

(21 in.)

600 mm

(24 in.)

150 mm

(6 in.)

25.4 mm (1 in.)

419 mm

(16.5 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

533 mm

(21 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

533 mm

(21 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

533 mm

(21 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

660 mm

(26 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

660 mm

(26 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

660 mm

(26 in.)

600 mm

(24 in.)

150 mm

(6 in.)

30 mm

(1.2 in.)

660 mm

(26 in.)

Table 1

22

9001014

Basic Installation/Operation

Ensure that the machine is installed on a level floor of sufficient strength and that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

W488

CAUTION

Machine Foundation

The washer-extractor must be placed on a smooth level surface so that the entire base of the machine is

Thoroughness of detail must be stressed with all

supported and rests on the mounting surface.

foundation work to ensure a stable unit installation. eliminating possibilities of excessive vibration during extract.

The standard installation does not require anchoring unless mandated by state or local codes.

Static and dynamic loads on the floor or foundation are shown in Table 2.

Table 2 can be used as a reference when designing floors and foundations.

Floor Load Data

Model 18253335405575100135165200

Kinetic Energy of the Cylinder, (N/m)

Dynamic Bottom Load, (N/Hz)

1386 1730 2736 3240 4105 6640 12404 18361 23257 29581 29581

700/16 750/16 1200/16 1200/16 1200/16 1700/15 2000/15 2960/13 3900/13 4960/13 6100/13

Table 2

9001014

23

Basic Installation/Operation

&)61

18 MODEL

660 mm

(26 in.)

560 mm

(22.05 in.)

670 mm

(26.38 in.)

55 mm

(2.17 in.)

486 mm

(19.13 in.)

87 mm

(3.43 in.)

55 mm

(2.17 in.)

87 mm

(3.43 in.)

CFS478N

660 mm

(26 in.)

660 mm

(25.98 in.)

87 mm

(3.43 in.)

55 mm

(2.17 in.)

770 mm

(30.31 in.)

87 mm

(3.43 in.)

486 mm

(19.13 in.)

55 mm

(2.17 in.)

25 MODEL

34 mm

(1.34 in.)

665 mm (25.18 in.)

680 mm (26.77 in.)

50 mm

(1.97 in.)

733 mm (28.86 in.)

50 mm

(1.97 in.)

780 mm (30.71 in.)

22 mm

(.87 in.)

33 MODEL

34 mm (1.34 in.)

CFS480N

35 MODEL

782 mm

(30.8 in.)

860 mm

(33.85 in.)

71 mm

(2.78 in.)

45 mm

(1.77 in.)

770 mm

(30.31 in.)

639 mm

(25.16 in.)

45 mm

(1.77 in.)

71 mm

(2.78 in.)

Mechanical Installation

Frame Dimensions and Mounting Bolt

Location for 18, 25, 33, 35, 40, 55, 75, 100, 135, 165 and 200 Models

CFS479N

CFD541N

Figure 14

Figure 12

CFS480N

Figure 15

CFS478N

Figure 13

24

9001014

Figure 16

CFD542N

34 mm

(1.34 in.)

765 mm (30.12 in.)

680 mm (26.77 in.)

50 mm

(1.97 in.)

633 mm (32.8 in.)

50 mm

(1.97 in.)

780 mm (30.71 in.)

22 mm

(0.87 in.)

40 MODEL

34 mm (1.34 in.)

CFS481N

55 MODEL

898 mm

(35.35 in.)

830 mm

(32.68 in.)

930 mm

(36.61 in.)

740 mm

(29.13 in.)

80 mm

(3.15 in.)

50 mm

(1.97 in.)

50 mm

(1.97 in.)

80 mm

(3.15 in.)

75 MODEL

1060 mm

(41.73 in.)

1080 mm (42.52 in.)

95 mm

(3.74 in.)

960 mm

(37.8 in.)

60 mm

(2.36 in.)

870 mm

(34.25 in.)

60 mm

(2.36 in.)

95 mm

(3.74 in.)

100 MODEL

1200 mm

(47.24 in.)

1090 mm

(42.91 in.)

80 mm

(3.15 in.)

1010 mm

(39.76 in.)

1040 mm

(40.94 in.)

40 mm

(1.57 in.)

40 mm

(1.57 in.)

80 mm

(3.15 in.)

Basic Installation/Operation

CFD542N

CFS483N

Figure 18

9001014

CFS481N

Figure 17

CFS482N

Figure 19

25

Basic Installation/Operation

135 MODEL

1200 mm

(47.24 in.)

1270 mm

(50 in.)

1185 mm

(46.65 in.)

80 mm

(3.15 in.)

1040 mm

(40.94 in.)

80 mm

(3.15 in.)

42,5 mm (1.67 in.)

165 MODEL

1300 mm

(51.2 in.)

1251 mm

(49.25 in.)

80 mm

(3.15 in.)

80 mm

(3.15 in.)

1185 mm

(46.7 in.)

114 0 m m (44.9 in.)

33 mm

(1.3 in.)

33 mm

(1.3 in.)

CFD536N

44 mm

(1.73 in.)

1300 mm (51.18 in.)

61 mm

(3.19 in.)

44 mm

(1.73 in.)

61 mm

(3.19 in.)

)

1138 mm (44.8 in.)

1300 mm (51.18 in.)

200 MODEL

1135 mm(44.8 in.)

Figure 20

CFd536N

Figure 22

CFS484N

26

CFS484N

Figure 21

9001014

Basic Installation/Operation

&)61

152 mm

(6 in.)

1

2

4

3

Mounting Bolt Installation (If Required)

1 Base Frame 2 Bolt 3 Washer 4 Anchor Bolt/Plug

4. To level machine, fill the spaces between the machine base and floor with machinery grout. Grout completely under all frame members. Remove front and rear panels to gain access to all frame members. Force grout under the machine base until all voids are filled.

5. Remove the spacers carefully, allowing the machine to settle into the wet grout.

6. Position washers and locknuts on machinery anchor bolts and finger-tighten to machine base.

7. After the grout is completely dry, tighten the locknuts by even increments – one after the other – until all are tightened evenly and the machine is fastened securely to the floor.

8. Remove the four red transport brackets which secure the moving components of the machine during shipping. Refer to Installation manual for typical transport bracket locations.

CFS485N

Figure 23

After the concrete has cured and the anchors are installed, proceed as follows:

1. Place the washer-extractor adjacent to the foundation. Do not attempt to move it by pushing on the sides. Always insert a pry bar or other device under the bottom of the frame of the washer-extractor to move it.

2. Place the washer-extractor carefully over the anchors.

3. Put bolts through the machine in the anchors and fasten them. (For the 18-25 and 35 models, the diameter of the bolt must be minimum 1/2-13 or 12 mm; for the 33-40-55-75-100-135-165 and 200 models, the diameter of the bolt must be minimum 5/8-11 or 16 mm.)

9001014

27

Basic Installation/Operation

Electrical Specifications

Voltage Designation Standard Electric Heat

2

Code

Model

Voltage

Cycle

Phase

Wire

Full

Load

Amps

Circuit

Breaker

AWG

18 N 440-480 50/60 3 3+PE 6 15 14/2.5 20 25 10/6.0

P 380-415 50/60 3 3+N+PE Not available 17 20 12/4.0

Q 200-240 50/60 3 3+PE Not available 28 30 10/6.0

X 200-240 50/60 1/3 2/3+PE 10 15 14/2.5 Not available

N 440-480 50/60 3 3+PE 6 15 14/2.5 21 25 10/6.0

25

P 380-415 50/60 3 3+N+PE Not available 18 20 12/4.0

Q 200-240 50/60 3 3+PE Not available 29 30 10/6.0

X 200-240 50/60 1/3 2/3+PE 10 15 14/2.5 Not available

N 440-480 50/60 3 3+PE 6 15 14/2.5 32 40 8/10.0

33

P 380-415 50/60 3 3+N+PE 18 20 12/4.0 44 50 8/10.0

Q 200-240 50/60 3 3+PE 18 20 12/4.0 63 70 4/25.0

X 200-240 50/60 1/3 2/3+PE 18 20 12/4.0 Not available

N 440-480 50/60 3 3+PE 12 15 14/2.5 41 50 8/10.0

35

P 380-415 50/60 3 3+N+PE Not available 36 40 8/10.0

Q 200-240 50/60 3 3+PE Not available 58 60 6/16.0

X 200-240 50/60 1/3 2/3+PE 12 15 14/2.5 Not available

N 440-480 50/60 3 3+PE 6 15 14/2.5 32 40 8/10.0

40

P 380-415 50/60 3 3+N+PE 18 20 12/4.0 44 50 8/10.0

Q 200-240 50/60 3 3+PE 18 20 12/4.0 63 70 4/25.0

X 200-240 50/60 1/3 2/3+PE 18 20 12/4.0 Not available

N 440-480 50/60 3 3+PE 12 15 14/2.5 41 50 8/10.0

55

P 380-415 50/60 3 3+N+PE Not available 36 40 8/10.0

Q 200-240 50/60 3 3+PE Not available 58 60 6/16.0

X 200-240 50/60 1/3 2/3+PE 16 20 14/2.5 Not available

N 440-480 50/60 3 3+PE 12 15 14/2.5 41 50 8/10.0

75

P 380-415 50/60 3 3+N+PE 12 15 14/2.5 36 40 8/10.0

Q 200-240 50/60 3 3+PE 15 20 12/4.0 58 60 6/16.0

N 440-480 50/60 3 3+PE 17 20 12/4.0 62 70 4/25.0

100

P 380-415 50/60 3 3+N+PE 17 20 12/4.0 55 60 6/16.0

Q 200-240 50/60 3 3+PE 18 25 10/6.0 88 90 3/35.0

N 440-480 50/60 3 3+PE 17 25 10/6.0 62 70 4/25.0

135

P 380-415 50/60 3 3+N+PE 17 25 10/6.0 55 60 6/16.0

Q 200-240 50/60 3 3+PE 20 30 10/6.0 88 90 3/35.0

N 440-480 50/60 3 3+PE 20 25 10/6.0 Not available

165

P 380-415 50/60 3 3+N+PE 20 25 10/6.0 Not available

Q 200-240 50/60 3 3+PE 32 40 8/10.0 Not available

Table 3 (continued)

/mm

Full

Load

Amps

Circuit

Breaker

AWG

2

/mm

28

9001014

Basic Installation/Operation

Table 3 (continued)

Electrical Specifications

Voltage Designation Standard Electric Heat

2

200

Code

Model

Voltage

Cycle

Phase

Wire

Full

Load

Amps

Circuit

Breaker

AWG

/mm

Full

Load

Amps

N 440-480 50/60 3 3+PE 19 25 10/6.0 Not available

P 380-415 50/60 3 3+N+PE 18 25 10/6.0 Not available

Q 200-240 50/60 3 3+PE 27 40 8/10.0 Not available

Table 3

Circuit

Breaker

AWG

/mm

9001014

29

Basic Installation/Operation

3

1

5

4

2

Control Identification

Operation

1 Keypad 4 Key Switch 2 Display 5 Serial Port 3 Emergency Stop Button

Figure 24

30

9001014

Basic Installation/Operation

Load the Machine

For models: 18PV-75PV

1. Pull the door handle towards you to open the door.

NOTE: Some models may have a door handle with a button that must be pressed.

2. Load the drum to the specified capacity.

3. Close the door by pushing the door handle towards the machine.

For models: 100PV-200PV

1. Push on the doorlock system to open the door.

2. Load the drum to the specified capacity.

3. Close the door by pushing the door handle towards the machine.

9001014

31

Basic Installation/Operation

Disposal of Unit

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Refer to Figure 25. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Ensuring this product is disposed of correctly will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact the local city office, household waste disposal service, or the source from which the product was purchased.

MIX1N

Figure 25

32

9001014

Alliance Laundry Systems 9001014R7 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual