ALLIANCE A135 ARIES, A180 ARIES, A105, IA80 ARIES, A80 ARIES Installation Operation & Maintenance

Washer-Extractors

Cabinet Hardmount

Refer to Page 8 for Model Identification

Installation/Operation/Maintenance

Original Instructions
Keep These Instructions for Futur

(If this machine changes ownership, this manual must accompany machine.)

e Reference.

www.alliancelaundry.com

Part No. D1634ENR4

January 2016

Table of Contents

Safety Information..................................................................................5

Explanation of Safety Messages....................................................................... 5

Important Safety Instructions........................................................................... 5

Safety Decals................................................................................................. 7

Operator Safety.............................................................................................. 7

Introduction........................................................................................... 8

Model Identification........................................................................................8

Delivery Inspection.........................................................................................8

Replacement Parts ......................................................................................... 8

Customer Service............................................................................................9

Specifications and Dimensions.............................................................. 10

General Specifications...................................................................................10

Machine Dimensions.....................................................................................15

Mounting Bolt Hole Locations – 8 kg / 20 lb. / 80 L, 11 kg / 25 lb. / 105 L and 14

kg / 30 lb. / 135L; 18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and 28 kg / 70

lb. / 280 L with 100 G Extraction................................................................17

Mounting Bolt Hole Locations – 18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and

28 kg / 70 lb. / 280 L with 175 G Extraction; 35 kg / 80 lb. / 332 L and 52 kg /

115 lb. / 520 L...........................................................................................18

Floor Mounting Layout .................................................................................19

Installation........................................................................................... 20

Pallet Removal............................................................................................. 20

Machine Installation......................................................................................21

Machine Foundation and Pad Installation.....................................................21

Machine Installation on Floor or Steel Base................................................. 23

Drain Connection..........................................................................................25

Drain Valve...............................................................................................26

Drain Pump, 8 kg / 20 lb. / 80 L Models...................................................... 29

Water Connection Requirements.....................................................................30

Water Reuse Connection............................................................................ 31

Reused Water Treatment............................................................................ 32

Water Reuse Tank Properties...................................................................... 32

Electrical Installation Requirements................................................................33

Residual Current Device (RCD) - Models Outside of North America............. 34

Supply Protection Device...........................................................................34

Supply Cable............................................................................................ 35

Machine Protective Earth Connection and Equipotential Bonding.................. 37

Input Power Conditioning..............................................................................38

©

Copyright 2016, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

3 Part No. D1634ENR4

Input Voltage Requirements........................................................................38

Circuit Breakers and Quick Disconnects......................................................... 38

Connection Specifications..............................................................................39

Single Phase Connection............................................................................39

Three Phase Connection.............................................................................39

Phase Adder..............................................................................................40

Thermal Overload Protector....................................................................... 40

Electrical Specifications.............................................................................40

Steam Requirements (Steam Heat Option Only)...............................................50

Steam Valve Installation.............................................................................51

Supply Dispensing........................................................................................ 51

Connection of External Liquid Supplies.......................................................... 51

Electrical Connection of External Liquid Soap Supply System.......................... 52

Operation............................................................................................. 53

Operating Instructions................................................................................... 53

Power Cut.................................................................................................... 54

Automatic Door-lock Unlocking Module........................................................ 54

Maintenance......................................................................................... 55

Maintenance.................................................................................................55

Daily........................................................................................................... 55

Beginning of Day...................................................................................... 55

End of Day............................................................................................... 55

Quarterly......................................................................................................56

Every 6 Months............................................................................................ 56

Care of Stainless Steel...................................................................................58

Disposal of Unit.................................................................................... 59

Disconnecting the Machine............................................................................59

Disposal of Unit............................................................................................59

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

4 Part No. D1634ENR4

Safety Information

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,” and
“CAUTION”), followed by specific instructions, are found in this
manual and on machine decals. These precautions are intended
for the personal safety of the operator, user, servicer, and those
maintaining the machine.

DANGER

Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.

WARNING

Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.

CAUTION

Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or
property damage.

Additional precautionary statements (“IMPORTANT” and
“NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used to in­form the reader of specific procedures where minor
machine damage will occur if the procedure is not fol­lowed.

NOTE: The word “NOTE” is used to communicate in­stallation, operation, maintenance or servicing informa­tion that is important but not hazard related.

Important Safety Instructions

WARNING

To reduce the risk of fire, electric shock, serious in­jury or death to persons when using your washer,
follow these basic precautions:

W023

• Read all instructions before using the washer.

• Install the washer according to the INSTALLATION instruc­tions. Refer to the Earthing (grounding) instructions in the IN­STALLATION manual for the proper earthing (grounding) of
the washer. All connections for water, drain, electrical power
and earthing (grounding) must comply with local codes and
be made by licensed personnel when required. It is recom­mended that the machine be installed by qualified technicians.

• Do not install or store the washer where it will be exposed to
water and/or weather.

• To prevent fire and explosion, keep the area around machine
free from flammable and combustible products. Do not add
the following substances or textiles containing traces of the
following substances to the wash water: gasoline, kerosene,
waxes, cooking oils, vegetable oils, machine oils, dry-clean­ing solvents, flammable chemicals, thinners, or other flamma­ble or explosive substances. These substances give off vapors
that could ignite, explode or cause the fabric to catch fire by
itself.

• Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using a
washing machine or combination washer-dryer, turn on all hot
water faucets and let the water flow from each for several mi­nutes. This will release any accumulated hydrogen gas. The
gas is flammable, do not smoke or use an open flame during
this time.

• To reduce the risk of an electric shock or fire, DO NOT use an
extension cord or an adapter to connect the washer to the elec­trical power source.

• Do not allow children to play on or in the washer. Close su­pervision of children is necessary when the washer is used
near children. This appliance is not intended for use by young
children or infirm persons without supervision. Young chil­dren should be supervised to ensure that they do not play with
the appliance. This is a safety rule for all appliances.

• DO NOT reach and/or climb into the tub or onto the washer,
ESPECIALLY if the wash drum is moving. This is an immi­nently hazardous situation that, if not avoided, will cause se­vere personal injury or death.

• Never operate the washer with any guards, panels and/or parts
removed or broken. DO NOT bypass any safety devices or
tamper with the controls.

• Use washer only for its intended purpose, washing textiles.
Never wash machine parts or automotive parts in the ma­chine. This could result in serious damage to the basket or
tub.

• Use only low-sudsing, no-foaming types of commercial deter­gent. Be aware that hazardous chemicals may be present.
Wear hand and eye protection when adding detergents and
chemicals. Always read and follow manufacturer’s instruc-

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

5 Part No. D1634ENR4

Safety Information

tions on packages of laundry and cleaning aids. Heed all
warnings or precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of children at all
times [preferably in a locked cabinet].

• Do not use fabric softeners or products to eliminate static un­less recommended by the manufacturer of the fabric softener
or product.

• To avoid machine corrosion and component failure, do not
use corrosive chemicals in the machine. Warranty claims rela­ted to damage caused by corrosive chemicals will be denied.

• Always follow the fabric care instructions supplied by the tex­tile manufacturer.

• Loading door MUST BE CLOSED any time the washer is to
fill, tumble or spin. DO NOT bypass the loading door switch
by permitting the washer to operate with the loading door
open. Do not attempt to open the door until the washer has
drained and all moving parts have stopped.

• Be aware that hot water is used to flush the supply dispenser.
Avoid opening the dispenser lid while the machine is running.

• Do not attach anything to the supply dispenser's nozzles, if
applicable. The air gap must be maintained.

• Do not operate the machine without the water reuse plug or
water reuse system in place, if applicable.

• Be sure water connections have a shut-off valve and that fill
hose connections are tight. CLOSE the shut-off valves at the
end of each wash day.

• Keep washer in good condition. Bumping or dropping the
washer can damage safety features. If this occurs, have wash­er checked by a qualified service person.

• DANGER: Before inspecting or servicing machine, power
supply must be turned OFF. The servicer needs to wait for at
least 10 minutes after turning the power OFF and needs to
check for residual voltage with a voltage meter. The inverter
remains charged with high voltage for some time after power­ing OFF. This is an imminently hazardous situation that, if not
avoided, will cause severe personal injury or death. Before
starting inspection of the inverter, check for residual voltage
across main circuit terminals + and -. This voltage must be
below 30 VDC before the servicer can access the inverter for
inspection.

• Do not repair or replace any part of the washer, or attempt any
servicing unless specifically recommended in the user-mainte­nance instructions or in published user-repair instructions that
the user understands and has the skills to carry out. ALWAYS
disconnect the washer from electrical, power and water sup­plies before attempting any service.

• Disconnect the power by turning off the circuit breaker or by
unplugging the machine. Replace worn power cords.

• Before the washer is removed from service or discarded, re­move the door to the washing compartment.

• Failure to install, maintain, and/or operate this washer accord­ing to the manufacturer’s instructions may result in conditions
which can produce bodily injury and/or property damage.

NOTE: The WARNING and IMPORTANT SAFETY IN­STRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Observe and be aware of other labels and pre­cautions that are located on the machine. They are in­tended to provide instruction for safe use of the ma­chine. Common sense, caution and care must be exer­cised when installing, maintaining, or operating the
washer.

Always contact your dealer, distributor, service agent or the man­ufacturer on any problems or conditions you do not understand.

NOTE: For European Union member states only: Elec­trical safety of the washers described in this manual is
in compliance with the requirements of the European
standard EN60204-1.

DANGER

Electrical shock hazard will result in death or serious
injury. Disconnect electric power and wait ten (10)
minutes before servicing.

W911

WARNING

Dangerous voltages are present inside the machine.
Only qualified personnel should attempt adjustments
and troubleshooting. Disconnect power from the ma­chine before removing any cover and guards, and
before attempting any service procedures.

W736

WARNING

Machine installations must comply with minimum
specifications and requirements stated in the appli­cable Installation Manual, any applicable municipal
building codes, water supply requirements, electrical
wiring regulations and any other relevant statutory
regulations. Due to varied requirements and applica­ble local codes, this machine must be installed, ad­justed, and serviced by qualified maintenance per­sonnel familiar with applicable local codes and the
construction and operation of this type of machinery.
They must also be familiar with the potential hazards
involved. Failure to observe this warning may result
in personal injury, property damage, and/or equip­ment damage, and will void the warranty.

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

W820

6 Part No. D1634ENR4

IMPORTANT: Ensure that the machine is installed on a
level floor of sufficient strength. Ensure that the recom­mended clearances for inspection and maintenance are
provided. Never allow the inspection and maintenance
space to be blocked.

WARNING

Safety Information

WARNING

NEVER insert hands or objects into basket until it
has completely stopped. Doing so could result in se­rious injury.

SW012

Never touch internal or external steam pipes, con­nections, or components. These surfaces can be ex­tremely hot and will cause severe burns. The steam
must be turned off and the pipe, connections, and
components allowed to cool before the pipe can be
touched.

SW014

WARNING

Install the machine on a level floor of sufficient
strength. Failure to do so may result in conditions
which can produce serious injury, death and/or prop­erty damage.

W703

WARNING

NEVER INTERFERE WITH THE SETTING OF THE
DOOR HANDLE. NEVER TRY TO MODIFY THE SET­TING OR REPAIR THE HANDLE! ANY INTERFER­ENCE WITH ITS SETTING MAY LEAD TO SERIOUS
RISK FOR THE OPERATOR! A DAMAGED OR INCOR­RECTLY FUNCTIONING DOOR HANDLE MUST AL­WAYS BE IMMEDIATELY REPLACED WITH A NEW
ORIGINAL PART.

C014

The following maintenance checks must be performed daily:

1. Verify that all warning labels are present and legible, replace
as necessary.

2. Check door interlock before starting operation of the ma­chine:

a. Attempt to start the machine with the door open. The ma-

chine should not start.

b. Close the door without locking it and start the machine.

The machine should not start.

c. Attempt to open the door while a cycle is in progress. The

door should not open.

If the door lock and interlock are not functioning properly, dis­connect power and call a service technician.

3. Do not attempt to operate the machine if any of the following
conditions are present:

a. The door does not remain securely locked during the en-

tire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly grounded circuit.

Do not bypass any safety devices in the machine.

WARNING

Operating the machine with severe out-of-balance
loads could result in personal injury and serious
equipment damage.

W728

Safety Decals

Safety decals appear at crucial locations on the machine. Failure
to maintain legible safety decals could result in injury to the oper­ator or service technician.

Use manufacturer-authorized spare parts to avoid safety hazards.

Operator Safety

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

7 Part No. D1634ENR4

Introduction

Model Identification

Information in this manual is applicable to these models:

Introduction

Models

A105

A105_ARIES

A135

A135_ARIES

A180

A180_ARIES

A80

A80_ARIES

IA80_ARIES

IA80_ARIES-ELITE

IA105_ARIES

IA105_ARIES-ELITE

IA135_ARIES

IA135_ARIES-ELITE

IA180_ARIES

IA180_ARIES-ELITE

IA240_ARIES

IAB180J

IAB180R

IAG080J

IAG080R

IAG105J

IAG105R

IAG135J

IAG135R

IAG180J

IAG180R

IAG240J

IAG240R

IAG280J

IAG280R

IAG332J

IAG332R

IAG520J

IAU080J

IAU080R

IAU105J

IAU105R

IAU135J

IAU135R

IAU180J

IAU180R

IAU240J

IAU240R

IAU280J

IAU280R

IAU332J

IAU332R

IAU520J

IAU520R

IAW080J

WMA103E

WMA103E_ARIES

WMA123E

WMA123E_ARIES

WMA153E

WMA153E_ARIES

WMA203E

WMA203E_ARIES

WMA253E

WMA253E_ARIES

WMA303E

WMA303E_ARIES

WMA403E

WMA403E_ARIES

WMA73E

WMA73E_ARIES

WMA83E

IA240_ARIES-ELITE

IA280_ARIES

IA280_ARIES-ELITE

IA332_ARIES

IA332_ARIES-ELITE

IA520_ARIES

IA520_ARIES-ELITE

IAG520R

IAGU080J

Delivery Inspection

Upon delivery, visually inspect crate, protective cover, and unit
for any visible shipping damage. If signs of possible damage are
evident, have the carrier note the condition on the shipping pa­pers before the shipping receipt is signed, or advise the carrier of
the condition as soon as it is discovered.

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

IAW080R

IAW105J

IAW105R

IAW135J

IAW135R

IAW180J

IAW180R

IAW240J

IAW240R

WMA83E_ARIES

Replacement Parts

If literature or replacement parts are required, contact the source
from which the machine was purchased or contact Alliance Laun­dry Systems at [phone] for the name and address of
the nearest authorized parts distributor.

8 Part No. D1634ENR4

Customer Service

For technical assistance, contact your local distributor or contact:

Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
U.S.A.
www.alliancelaundry.com
Phone: [phone] Ripon, Wisconsin
Alliance International: [phone] Wevelgem, Belgium

Introduction

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

9 Part No. D1634ENR4

Specifications and Dimensions

General Specifications

Specifications and Dimensions

8 kg /

20 lb. /
Specifi­cations

Overall Dimensions

Overall
width, in.
[mm]

Overall
height, in.
[mm]

Overall
depth, in.
[mm]

Weight and Shipping Information

Net weight,
lbs. [kg]
(100G)

80 L

Models

25.98 [660] 29.53 [750] 29.53 [750] 35.03 [890] 35.03 [890] 35.03 [890] 41.73

43.89
[1115]

30.91 [785] 30.91 [785] 35.43 [900] 36.02 [915] 41.73

298 [135] 375 [170] 419 [190] 563 [255] 606 [275] 639 [290] 904 [410] 1146 [520]

11 kg /
25 lb. /
105 L
Models

48.22
[1225]

14 kg /
30 lb. /
135 L
Models

48.22
[1225]

18 kg /
40 lb. /
180 L
Models

55.51
[1410]

24 kg /
55 lb. /
240 L
Models

55.51
[1410]

[1060]

28 kg /
70 lb. /
280 L
Models

55.51
[1410]

44.68
[1135]

35 kg /
80 lb. /
332 L
Models

[1060]

59.05
[1500]

40.55
[1030]

52 kg /
115 lb. /
520 L
Models

41.73
[1060]

59.05
[1500]

51.77
[1315]

Net weight,
lbs. [kg]
(150G)

Net weight,
lbs. [kg]
(175G)

Shipping
weight, lbs.
[kg](100G)

Shipping
weight, lbs.
[kg](150G)

Shipping
weight, lbs.
[kg](175G)

N/A N/A N/A N/A N/A N/A 904 [410] N/A

298 [135] 375 [170] 419 [190] 695 [315] 728 [330] 783 [355] N/A N/A

320 [145] 408 [185] 441 [200] 595 [270] 639 [290] 672 [305] 992 [450] 1257 [570]

N/A N/A N/A N/A N/A N/A 1147 [520] N/A

320 [145] 408 [185] 441 [200] 739 [335] 783 [355] 849 [385] N/A N/A

Table continues...

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

10 Part No. D1634ENR4

Specifications and Dimensions

8 kg /

20 lb. /
Specifi­cations

Shipping
dimensions
(WxDxH),
in. [mm]

80 L

Models

27.95 x

32.87 x

49.02 [710
x 835 x
1245]

Wash Cylinder Information

Cylinder

20.87 [530] 24.40 [620] 24.40 [620] 29.53 [750] 29.53 [750] 29.53 [750] 35.98 [914] 35.98 [914]
diameter
in. [mm]

Cylinder

13.78 [350] 13.78 [350] 17.72 [450] 16.14 [410] 21.46 [545] 24.41 [620] 19.88 [505] 31.10 [790]
depth in.
[mm]

Cylinder
volume ft

2.6 [75] 3.7 [105] 4.8 [135] 6.4 [180] 8.5 [240] 9.9 [280] 11.7 [332] 20.47 [520]

3

[l]

11 kg /
25 lb. /
105 L
Models

31.50 x

32.87 x

53.35 [800
x 835 x
1355]

14 kg /
30 lb. /
135 L
Models

31.50 x

37.40 x

53.35 [800
x 950 x
1355]

18 kg /
40 lb. /
180 L
Models

36.42 x

38.19 x

61.02 [925
x 970 x
1550]

24 kg /
55 lb. /
240 L
Models

36.42 x

44.49 x

61.02 [925
x 1130 x
1550]

28 kg /
70 lb. /
280 L
Models

36.42 x

46.85 x

61.02 [925
x 1190 x
1550]

35 kg /
80 lb. /
332 L
Models

43.31 x

43.31 x

66.93
[1100 x
1100 x
1700]

52 kg /
115 lb. /
520 L
Models

43.31 x

54.53 x

66.93
[1100 x
1385 x
1700]

Door Opening Information

Door open-

13 [330] 16.14 [410] 16.14 [410] 18.11 [460] 18.11 [460] 18.11 [460] 19.84 [504] 19.84 [504]
ing size, in.
[mm]

Height of

13.74 [349] 13.46 [342] 13.46 [342] 18.31 [465] 18.31 [465] 18.31 [465] 18.31 [465] 18.31 [465]
door bot­tom above
floor, in.
[mm]

Drive Train Information

Number of

1 1 1 1 1 1 1 1
motors in
drive train

Motor Size,

0.67 [0.5] 0.67 [0.5] 1 [0.75] 1 [0.75] 1.48 [1.1] 1.5 [2.01] 2.95 [2.2] 5.36 [4]
hp [kW]
(100G)

Motor Size,

N/A N/A N/A N/A N/A N/A 2.95 [2.2] N/A
hp [kW]
(150G)

Motor Size,

0.67 [0.5] 0.67 [0.5] 1 [0.75] 1.48 [1.1] 2.01 [1.5] 2.01 [1.5] N/A N/A
hp [kW]
(175G)

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

Table continues...

11 Part No. D1634ENR4

Specifications and Dimensions

Specifi­cations

Motor Size,

0.67 [0.5] 0.74 [0.55] 1 [0.75] 1.48 [1.1] 2.01 [1.5] 2.01 [1.5] N/A N/A
hp [kW]
(200G)

Cylinder Speeds

Wash,

50 46 46 42 42 42 38 38

RPM

Extraction,

580 540 540 490 490 490 440 440
RPM
(100G)

Extraction,

N/A N/A N/A N/A N/A N/A 540 N/A
RPM
(150G)

Extraction,

770 710 710 645 645 645 N/A N/A
RPM
(175G)

8 kg /
20 lb. /
80 L
Models

11 kg /
25 lb. /
105 L
Models

14 kg /
30 lb. /
135 L
Models

18 kg /
40 lb. /
180 L
Models

24 kg /
55 lb. /
240 L
Models

28 kg /
70 lb. /
280 L
Models

35 kg /
80 lb. /
332 L
Models

52 kg /
115 lb. /
520 L
Models

Heating

Electric,
kW

Steam, psi
[bar]

Hot water,
°F [°C]

Noise Emissions

Wash se­quence, dB
(100 G)

Wash se­quence, dB
(150 G)

Wash se­quence, dB
(175 G)

Extract se­quence, dB
(100G)

6 / 9 (4.6) 6 / 9 / 12 9 / 12 12 / 18 18 21.9 27 40.6

15-116

[1-8]

15-116
[1-8]

15-116
[1-8]

15-116
[1-8]

15-116
[1-8]

15-116
[1-8]

15-116
[1-8]

15-116
[1-8]

90 [194] 90 [194] 90 [194] 90 [194] 90 [194] 90 [194] 90 [194] 90 [194]

49 49 50 48 50 50 50 50

N/A N/A N/A N/A N/A N/A 50 N/A

49 49 50 50 50 50 N/A N/A

53 53 65 55 65 65 65 65

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

Table continues...

12 Part No. D1634ENR4

Specifications and Dimensions

Specifi­cations

Extract se-

N/A N/A N/A N/A N/A N/A 65 N/A
quence, dB
(150G)

Extract se-

53 53 65 65 65 65 N/A N/A
quence, dB
(175G)

Floor Load Data

Maximum

427 [1.9] 495 [2.2] 607 [2.7] 764 [3.4] 877 [3.9] 944 [4.2] 1461 [6.5] 1888 [8.4]
static load
on floor,
lbs. [kN]
(100G)

Maximum

N/A N/A N/A N/A N/A N/A 1461 [6.5] N/A
static load
on floor,
lbs. [kN]
(150G)

8 kg /
20 lb. /
80 L
Models

11 kg /
25 lb. /
105 L
Models

14 kg /
30 lb. /
135 L
Models

18 kg /
40 lb. /
180 L
Models

24 kg /
55 lb. /
240 L
Models

28 kg /
70 lb. /
280 L
Models

35 kg /
80 lb. /
332 L
Models

52 kg /
115 lb. /
520 L
Models

Maximum
static load
on floor,
lbs. [kN]
(175G)

Maximum
dynamic
load on
floor, lbs.
[kN]
(100G)

Maximum
dynamic
load on
floor, lbs.
[kN]
(150G)

Maximum
dynamic
load on
floor, lbs.
[kN]
(175G)

427 [1.9] 495 [2.2] 607 [2.7] 899 [4.0] 1012 [4.5] 1101 [4.9] N/A N/A

360 ± 337

[1.6 ± 1.5]

N/A N/A N/A N/A N/A N/A 1191

427 ± 450
[1.9 ± 2.0]

495 ± 562
[2.2 ± 2.5]

607 ± 719
[2.7 ± 3.2]

674 ± 967
[3.0 ± 4.3]

719 ± 1124
[3.2 ± 5.0]

1191
± 1866 [5.3
± 5.5]

1506
± 1843 [6.7
± 8.2]

N/A
± 1866 [5.3
± 8.3]

360 ± 562
[1.6 ± 2.5]

427 ± 764
[1.9 ± 3.4]

495 ± 989
[2.2 ± 4.4]

764 ± 1259
[3.4 ± 5.6]

832 ± 1664
[3.7 ± 7.4]

877 ± 1956
[3.9 ± 8.7]

N/A N/A

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

Table continues...

13 Part No. D1634ENR4

Specifications and Dimensions

Specifi­cations

Frequency
of dynamic
load, Hz
(100G)

Frequency
of dynamic
load, Hz
(150G)

Frequency
of dynamic
load, Hz
(175G)

General Data

Ambient
Tempera­ture, °F
[°C]

8 kg /
20 lb. /
80 L
Models

11 kg /
25 lb. /
105 L
Models

14 kg /
30 lb. /
135 L
Models

18 kg /
40 lb. /
180 L
Models

24 kg /
55 lb. /
240 L
Models

28 kg /
70 lb. /
280 L
Models

35 kg /
80 lb. /
332 L
Models

52 kg /
115 lb. /
520 L
Models

9.7 8.9 8.9 8.2 8.2 8.2 9 7.4

N/A N/A N/A N/A N/A N/A 9 N/A

12.8 11.8 11.8 10.8 10.8 10.8 N/A N/A

41-95 [5-35]

Relative
Humidity

Height
above sea
level ft.
[m]

Storage
Tempera­ture, °F
[°C]

30%-90% without condensation

up to 3280 [up to 1000]

34-131 [1-55]

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

14 Part No. D1634ENR4

Machine Dimensions

1

A

B

C

D

E

F

2

3

G

H

I

J

K

L

M

N

O

P

Q

R

S

4

5

6

7

8

9

10

11

121314 15 16

17

18

19

20

21

22

CHM2465N_SVG

Specifications and Dimensions

1. Control panel

2. Soap dispenser

3. Centralstop button

4. Steam connection

5. Air relieve

6. Liquid soap connection

7. Recyled water inlet

8. Steam valve connection

9. Recycled water valve cable inlet

10. Cold water inlet, soft

11. Cold water inlet, hard

12. Electrical connection

13. Hot water inlet

14. Main switch

15. Heating change-over switch

16. Liquid soap pump eletrical connection

17. Fuses

18. USB port

19. PC programming connection

20. Discharge water cable inlet

21. Drain valve - 3 in. 76 mm

22. Drain valve - 3 in. 76 mm (80 and 115 lb. [332 and 520 L] Models only)

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

Figure 1

15 Part No. D1634ENR4

Specifications and Dimensions

8 kg /
20 lb. /
80 L

Models,
Specifi­cation

in.

[mm]

A 25.98 [660] 29.53 [750] 29.53 [750] 35.03 [890] 35.03 [890] 35.03 [890] 41.73

11 kg /
25 lb. /
105 L
Models,
in.
[mm]

14 kg /
30 lb. /
135 L
Models,
in.
[mm]

18 kg /
40 lb. /
180 L
Models,
in.
[mm]

24 kg /
55 lb. /
240 L
Models,
in.
[mm]

28 kg /
70 lb. /
280 L
Models,
in.
[mm]

35 kg /
80 lb. /
332 L
Models,
in.
[mm]

[1060]

52 kg /
115 lb. /
520 L
Models,
in.
[mm]

41.73
[1060]

B 13.74 [349] 13.46 [342] 13.46 [342] 18.31 [465] 18.31 [465] 18.31 [465] 18.31 [465] 18.31 [465]

C 43.89

[1115]

48.22
[1225]

48.22
[1225]

55.51
[1410]

55.51
[1410]

55.51
[1410]

59.05
[1500]

59.05
[1500]

D 7.08 [180] 7.56 [192] 7.56 [192] 4.72 [120] 4.72 [120] 4.72 [120] 5.71 [145] 5.71 [145]

E 30.91 [785] 30.91 [785] 35.43 [900] 36.02 [915] 41.73

[1060]

F 26.61 [676] 26.61 [676] 31.14 [791] 32.13 [816] 37.83 [961] 40.79

G 40.35

[1025]

44.68
[1135]

44.68
[1135]

51.85
[1317]

51.85
[1317]

44.68
[1135]

[1036]

51.85
[1317]

40.55
[1030]

51.77
[1315]

36.89 [937] 48.11
[1222]

55.63

[1413]

52.44
[1332]

H 39.76

[1010]

I 36.22 [920] 40.55

44.09
[1120]

[1030]

44.09
[1120]

40.55
[1030]

51.06
[1297]

47.72
[1212]

51.06
[1297]

47.72
[1212]

51.06
[1297]

47.72
[1212]

53.78

[1366]

52.21

[1326]

54.09
[1374]

55.67
[1414]

J 21.06 [535] 18.89 [480] 18.89 [480] 20.79 [528] 20.79 [528] 20.79 [528] 20.79 [528] 20.79 [528]

K 3.46 [88] 3.85 [98] 3.95 [98] 5.12 [130] 5.12 [130] 5.12 [130] 4.72 [120] 4.72 [120]

L 6.53 [166] 8.85 [225] 8.85 [225] 11.02 [280] 11.02 [280] 11.02 [280] 12.52 [318] 12.52 [318]

M N/A N/A N/A N/A N/A N/A 18.98 [482] 18.98 [482]

N 40.15

[1020]

44.48
[1130]

44.48
[1130]

50 [1270] 50 [1270] 50 [1270] 53.11

[1349]

53.11
[1349]

O 1.89 [48] 1.65 [42] 1.65 [42] 2.13 [54] 2.13 [54] 2.13 [54] 2.60 [66] 2.60 [66]

P 11.53 [293] 13.31 [338] 13.31 [338] 11.93 [303] 11.93 [303] 11.93 [303] 15.08 [383] 14.29 [363]

Q 16.34 [415] 19.88 [505] 19.88 [505] 24.61 [625] 24.61 [625] 24.61 [625] 26.42 [671] 26.41 [671]

R 8.58 [218] 8.58 [218] 8.58 [218] 8.58 [218] 8.58 [218] 8.58 [218] 9.76 [248] 8.78 [223]

S 4.44 [113] 4.44 [113] 4.44 [113] 4.44 [113] 4.44 [113] 4.44 [113] 4.45 [113] 3.46 [88]

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

Table 1

16 Part No. D1634ENR4

CHM2467N_SVG

F

EE

D D

C C

B

A

1

G

C C

Specifications and Dimensions

Mounting Bolt Hole Locations – 8 kg / 20 lb. / 80 L, 11 kg / 25 lb. / 105 L and 14

kg / 30 lb. / 135L; 18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and 28 kg / 70 lb. / 280
L with 100 G Extraction

8 kg / 20 lb. / 80 L, 11 kg / 25 lb. / 105 L and 14 kg / 30 lb. / 135 L; 18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and
28 kg / 70 lb. / 280 L with 100 G Extraction)

1. Front of machine

Figure 2

Mounting Bolt Hole Locations – 8 kg / 20 lb. / 80 L, 11 kg / 25 lb. / 105 L and 14 kg / 30 lb. / 135 L; 18 kg / 40 lb. /

180L, 24 kg / 55 lb. / 240 L and 28 kg / 70 lb. / 280 L with 100 G Extraction, in. [mm]

Spec
ifica-

tion

8 kg / 20 lb. /

80 L

11 kg / 25 lb. /

105 L

14 kg / 30 lb. /

135 L

18 kg / 40 lb. /

180 L (100G)

24 kg / 55 lb. /

240 L (100G)

28 kg / 70 lb. /

280 L (100G)

A 20.55 [522] 24.21 [615] 24.21 [615] 29.57 [751] 29.57 [751] 29.57 [751]

B 18.66 [474] 18.66 [474] 22.59 [574] 22.40 [569] 28.11 [714] 31.06 [789]

C 2.71 [69] 2.85 [67.5] 2.65 [67.5] 2.74 [69.5] 2.74 [69.5] 2.74 [69.5]

D 5.47 [139] 5.47 [139] 6.06 [154] 8.68 [220.5] 8.68 [220.5] 8.68 [220.5]

E 2.26 [57.5] 2.26 [57.5] 2.26 [57.5] 1.97 [50] 1.97 [50] 1.97 [50]

F 25.98 [660] 29.52 [750] 29.52 [750] 35.04 [890] 35.04 [890] 35.04 [890]

G 26.39 [670.5] 26.39 [670.5] 30.92 [785.5] 33.01 [838.5] 38.76 [984.5] 41.71 [1059.5]

Table 2

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

17 Part No. D1634ENR4

CHM2468N_SVG

G

F

E E

D D

C C

C C

B

A

1

H H

H H

Specifications and Dimensions

Mounting Bolt Hole Locations – 18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and 28

kg / 70 lb. / 280 L with 175 G Extraction; 35 kg / 80 lb. / 332 L and 52 kg / 115 lb. /
520 L

18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and 28 kg / 70 lb. / 280 L with 175 G Extraction; 35 kg / 80 lb. / 332 L
and 52 kg / 115 lb. / 520 L

1. Front of machine

Mounting Bolt Hole Locations – 18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and 28 kg / 70 lb. / 280 L with 175 G
Extraction; 35 kg / 80 lb. / 332 L and 52 kg / 115 lb. / 520 L

in. [mm]

Speci-

fica-

tion

18 kg / 40 lb. /

180 L (175G)

A 29.57 [751] 29.57 [751] 29.57 [751] 36.22 [920] 36.22 [920]

B 22.40 [569] 28.11 [714] 31.06 [789] 25.16 [639] 36.38 [924]

C 2.74 [69.5] 2.74 [69.5] 2.74 [69.5] 2.76 [70] 2.76 [70]

D 8.68 [220.5] 8.68 [220.5] 8.68 [220.5] 10.69 [271.5] 10.69 [271.5]

E 1.97 [50] 1.97 [50] 1.97 [50] 1.97 [50] 1.97 [50]

F 35.04 [890] 35.04 [890] 35.04 [890] 41.73 [1060] 41.73 [1060]

G 33.01 [838.5] 38.76 [984.5] 41.71 [1059.5] 37.82 [960.5] 49.04 [1245.5]

H 3.23 [82] 3.23 [82] 3.23 [82] 3.23 [82] 3.23 [82]

24 kg / 55 lb. /

240 L (175 G)

Figure 3

28 kg / 70 lb. /

280 L (175G)

Table 3

835 kg / 80 lb. /

332 L

52 kg / 115 lb. /

520 L

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

18 Part No. D1634ENR4