AllerAir AirTube Jr, AirTube Supreme User Manual

REPLACING FILTER ASSEMBLY- AirTube Jr.

Step 2

Step 1

Turn Power Off and
unplug receptacle.

Step 5

To replace the electrostatic HEPA
filter,gently remove the filter from
carbon canister and replace with a
new one.

Gently lay unit up-side down. With
a screw driver,remove all 4 screws.

Step 3

Remove lid by pulling slightly on
cover.

Step 6

Replace all filters with new ones
then reassemble by inserting the
Carbon filter.

Step 4

Remove Carbon filter by placing
hands on the inner side of the filter.

Then pull up gently until totally out.

Step 7

Place lid back to its proper position
by aligning screw holes.

Step 8

With a screw driver, place 4
screws back into their positions.

Operation and Maintenance Manual for

Air Tube Series

REPLACEMENT PARTS

MODELS Air Tube Jr. Air Tube Air Tube Supreme

Carbon (Exec Models)
Carbon ( Vocarb Models)
Micro-HEPA Wrap
PRE-FILTER --------------------­Motor A2EL0040 A2EL0040 A2EL0040
Switch CMEL0046 CMEL0046 CMEL0046
Cord A3EL0046 A3EL0046 A3EL0046
Handle A4HD8414 A4HD8414 A4HD8414

9" A2FCW301 9" A3FCW302 12" A3FCB401
9" A2FCW302 9" A3FCW303 12" A3FCB403
A2FMR002 9 x 21 A3FH0410 HEPA A3FH0420 HEPA

A3FMP009 A3FMP012

AllerAir Industries Inc.

AirTube

AirTube Supreme

AirT ube Jr.

T oll free: 1-888-852-8247 / Fax: [phone] www.allerair .com

AllerAir Industries Inc.

AirTube Series

Congratulations, you are moments away from fresher,cleaner indoor air.
Your new AllerAir unit will combat many of the chemicals, gases, odors and
particles responsible for poor indoor air qualit y, and in turn, health concerns
such as allergies, asthma, sick building syndrome and multiple chemical
sensitivity. As with any air cleaner, proper maintenance of your unit is a vital
part of keeping it operating at peak efficiency.

Operation:

Your unit is shipped fully assembled and ready for use. Plug into 120V­15amp outlet. For best results situate your unit close to your sitting,
sleeping or work area.

NOTE: Please save your packaging. Original packaging will be required for
all warranty returns.

WARNING !

Before removing the top or bottom of the unit for any
reason, always unplug the cord from the power supply.

Maintenance:

REPLACING FILTER ASSEMBLY-

AirTube & Air Tube Supreme

Step 1

Turn Power Off and
unplug receptacle.

Step 2

Gently lay unit up-side down. With
a screw driver,remove all 4 screws.

Step 3

Remove lid by pulling slightly on
cover.

A

B

AirTube & Air Tube Supreme

The HEPA Filter (Model AirTube HEPA)

Should be changed after
approximately 24 months of use
in an average home environment.
A noticeable lessoning of air flow
is a sign that it may be time to
replace this filter.

The Carbon Filter (Model AirTube Carbon)

Should be changed after
approximately 12 months of use
in an average home environment.
A noticeable decrease in air
quality could also be a sign that it
may be time to replace this filter.

The Pre-filter (Model AirTube Prefilter)

Replace or vacuum from the
outside of the unit ever y 2-3
months.

AirTube Jr.

The Electrostatic HEPA Filter

(Model AirTube Jr. Electrostatic HEPA)

Should be changed after
approximately 12 months of use in
an average home environment.
A noticeable lessoning of air flow
is a sign that it may be time to
replace this filter.

The Carbon Filter (Model AirTube Jr. Carbon)

Should be changed after
approximately 9-12 months of use
in an average home environment.
A noticeable decrease in air
quality could also be a sign that it
may be time to replace this filter.

Step 4

First remove HEPA filter by placing
your hand on the inner side of the
filter.

Then pull up gently until totally out.

Step 7

Replace all filters with new ones
then reassemble by inserting the
Carbon filter first then the HEPA.

Step 5

Now remove Carbonfilterbyplacing
hands on the inner side of the filter.

Then pull up gently until totally out.

Step 8

Place lid back to its proper position
by aligning screw holes.

Step 6

A- To replace pre-filter,gently

remove pre-filter from Carbon
canister and replace with new one.

B- To replace Anti-microbial filter,
peel off filter liner.

Step 9

With a screw driver, place 4
screws back into their positions.