Allen Sports XLT-X2 User Manual
INSTRUCTIONAL
OWNER’S MANUAL
MODEL XLT-X2 BIKE TRAILER
Owner’s Manual should be kept for future reference
1. Completely read and understand Owner’s Manual before assembling or operating this product.
2. This product should be assembled by an adult
IMPORTANT SAFETY INFORMATION
• Failure to follow these warnings and assembly instructions could result in serious injury or death!
• Immediately discard all plastic bags and plastic wrapping materials!
• Maximum total weight capacity for one child is 50 pounds, and for two children is 100 pounds!
• Never use this trailer/stroller if it becomes damaged!
• To avoid serious injury, children should always wear the seat belt and the shoulder straps!
• Never leave children unattended in or around this product!
• Never allow children to assemble, fold, or disassemble this unit!
• Accessories or parcels placed in trailer/stroller may cause it to become unstable!
• Not for use with children under 12 months old! Children must be able to support their own heads!
• Before riding, check that all parts are assembled according to the manufacturer instructions!
• Tires should be inflated to 25-35 PSI for maximum comfort! Check tire pressure before each use!
• Use a foot pump or hand pump to inflate tires! Pressurized air hoses can cause over inflation!
• Periodically re-check all fasteners to make sure they are tight!
• Clean trailer only with soap and water. Do not use solvents!
WARNING
1
WARNING
SAFETY TOWING TIPS
• Make sure your bike brakes work properly! Braking distance is increased when pulling a trailer!
• This trailer is wide! Allow extra clearance near curbs, signs, parked cars, and other obstacles!
• A bicycle with trailer attached requires a wide turning radius! Do not turn sharply!
• Children must wear an approved safety helmet when using this product in trailer mode!
• Never remove protective canopy when pulling children in the trailer!
• Always use the safety flag when pulling this trailer!
• When pulling one child in the trailer, seat him/her in the enter!
• Do not ride over curbs! Avoid bumps and holes! Always signal your turns!
• Use extra caution when turning on uneven pavement, and going downhill!
• Not for use at high speeds! Do not exceed 10 MPH!
• NEVER use this trailer at night!
• Install a rearview mirror on your bike to check on children in trailer!
• Dress children appropriately to prevent them from getting chilled or overheated while riding!
Protect against wind-chill in cold temperatures, and provide adequate ventilation and hydration
WARNING
during warmer temperatures.
WARNING
INSTRUCTIONAL
OWNER’S MANUAL
FULLY ASSEMBLED TRAILER
2
PARTS LIST
QUANTITY DESCRIPTION
1 Frame w/ Canopy, Sling
Seat with 5 point safety
harness, tow bar, tow
bar coupler and rear
wheel bracket attached
2 20” Rear wheels
1 Safety flag
INSTRUCTIONAL
OWNER’S MANUAL
MAIN CABIN FRAME AND ASSEMBLY
3
STEP 1:
NOTE: 1. Set the walking kit small swivel wheel aside, as you will
install this later.
2. Lay the trailer on the ground with the black fabric
side down.
STEP 2:
STEP 3:
STEP 4:
Remove the trailer, wheels, hitch arm and walking kit from the box.
To open frame, first, lift front cabin tube up, and then lift rear cabin tube (Fig 2), allowing the rear cabin
tube to meet and rest in the plastic cradle of the front tube, (Fig 3, 4).
Next, lift the handlebar, rotating it toward the back of the trailer, and press down until the latches engage (Fig 5).
Finally, close the black paddle latch in the center of the handlebar assembly to lock the frame in place (Fig 6).
FIGURE A
FIGURE 1.
FIGURE 4.
WARNING!: You must make certain the frame is locked before using the trailer. Failure to do so could result in
serious injury to you or your child. Make sure the secondary paddle latch is engaged prior to use. Both
latches are necessary for safe operation.
FIGURE 2.
FIGURE 5.
FIGURE 3.
FIGURE 6.
INSTRUCTIONAL
OWNER’S MANUAL
WHEEL INSTALLATION
Your Allen Sports trailer uses simple and convenient push button quick-release wheels.
4
STEP 1:
STEP 2:
STEP 3:
STEP 4:
WARNING!: Check the wheels periodically during and before each use to be sure they have not become
loose. Failure to do so could result in serious injury to you or your child.
Push the button on the outside of the wheel hub.
Insert the axle through the hanger bracket on the frame as shown (Fig. 7).
Push all the way in and release the pushbutton. The wheel is automatically
locked in place.
Give each wheel a tug to make sure they are secure.
FIGURE 7
TOW ARM
STEP 1:
STEP 2:
Locate the hitch arm, and position on the left side of the trailer, as shown (Fig. 8). The hitch arm is held in
place by a spring pin and a quick release pin.
Depress the spring pin and insert the hitch arm in the bracket on the frame as shown (Fig. 8).
STEP 3:
STEP 4:
FIGURE 8 FIGURE 9
WARNING!: Check this pin periodically during and before each use to be sure it has not become loose.
Failure to do so could result in serious injury to you or your child.
Once the spring pin locks in place in the hole in the bracket, Locate the quick release pin, located on the trailer
frame, then Insert the pin through the bracket and into the hole in the tow arm (Fig. 9 & 10). The pin should go
completely through the tow arm and bracket.
Give the pin a tug to be sure it is secure.
FIGURE 10
Loading...