Model 104S Instructions
English - Page 1
WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury—do not use rack on any
vehicle on which it can not be properly mounted as described in this instruction sheet.
Top hooks must be completely hooked over solid metal edges at top/ front of trunk lid or rear door—never hook to
rain gutters, roof racks, vertical glass, rubber or plastic moldings.
Mount rack only with bottom feet on a rigid surface of car (never on glass), and with bottom foot assembly com-
pletely extended. Never use rack on trailers or on the front of vehicles.
Never carry more than 4 bicycles (MAX CAPACITY: 140 LB) - no tandems, mopeds, or recumbents. Car tail light s
must remain visible. Bikes must be securely tied to rack. Use bike tie-downs, or additional straps if necessary.
Drive conservatively, especially over bumps. Never use off-road.
Do not use if any part of the rack is damaged, worn, or missing. Contact R. A. Allen Co., Inc. for replacement parts.
ETTING UP RACK:
S
A.
NOTE: DRAWINGS BELOW SHOWS MODEL 103S
1. FOLD OUT TOP FOOT/ CARRY-
ARM ASSEMBLY.
2. SET-UP PINS WILL
NAP” INTO
“S
PLACE.
3. COMPLETELY FOLD OUT
B.
OTTOM FOOT ASSEMBLY.
B
B
EFORE INSTALLING RACK:
1. MAKE SURE THAT CONTACT SURFACES BE-
CAR AND RUBBER FEET ARE THOR-
TWEEN
OUGHLY
THAT ALL RUBBER
FEET ARE PROPERLY
SPACED.
CLEAN AND FREE OF DIRT, AND
2. MAKE SURE THAT
TOP BUCKLES ARE
THREADED AS
SHOWN ON RIGHT.
K
O
O
H
O
T
3. I
NSPECT ALL
STRAPS TO MAKE SURE THAT THEY ARE NOT
WORN OR DAMAGED IN ANY WAY.
IMPORTANT IN-
STALLATION
TICE
1. BOTTOM FOOT ASSEMBLY MUST BE
COMPLETELY EXTENDED. IF TOP FEET
ARE MOUNTED ON THE HORIZONTAL
SURFACE OF THE REAR TRUNK,
BOTTOM FEET MUST BE SUP-
BY THE TOP
PORTED
HORIZONTAL SURFACE
OF THE
BUMPER.
2. NEVER INSTALL RACK WITH ITS BOT-
FEET ON THE OUTSIDE VERTICAL
TOM
SURFACE OF THE BUMPER.
3. NEVER INSTALL RACK WITHOUT
BOTTOM FOOT IN A COMPLETELY
EXTENDED POSITION
NO-
:
C. INSTALLING RACK ON VEHICLE:
1. TOP HOOKS MUST BE COMPLETELY HOOKED OVER METAL EDGES AT TOP OF TRUNK, REAR DOOR, OR
HATCHBACK. NEVER HOOK TO RAIN GUTTERS, ROOF
RACKS, VERTICAL GLASS OR PLASTIC MOLDINGS.
PEN TRUNK/ HATCH SLIGHTLY FOR EASIEST ATTACH-
O
OF HOOKS.
MENT
BIND WHEN TRUNK/ HATCH IS OPENED
HOOKS WILL DAMAGE VEHICLE
ECURING TOP HOOKS ON VEHICLES WITHOUT ADE-
S
QUATE
CLEARANCE AT THE TOP EDGE OF REAR
TRUNK/ HATCH: UNTHREAD TOP STRAPS FROM
METAL BUCKLES AND OPEN REAR TRUNK/ HATCH.
LACE TOP HOOKS INSIDE OF VEHICLE (JUST INSIDE
P
OF TOP EDGE OF REAR TRUNK/ HATCH).
CLOSE REAR TRUNK/ HATCH ON TOP STRAPS, MAKING
CERTAIN HOOKS DO NOT BIND BETWEEN FRAME AND
REAR DOOR. IMPORTANT: WITH REAR DOOR
CLOSED, PULL TOP STRAPS TO BRING HOOKS TIGHT
AGAINST INSIDE OF VEHICLE. RE-THREAD TOP
STRAPS AS SHOWN IN SECTION B. MOUNT RACK TO VEHICLE.
ET LENGTH OF TOP STRAPS TO POSITION RACK WITH ITS CARRY ARMS INCLINED SLIGHTLY UP-
2. S
WARDS
, AND HIGH ENOUGH TO KEEP BIKES AWAY FROM ROAD AND EXHAUST.
3. ONCE THE LENGTH OF THE TOP STRAPS ARE SET, THE
BOTTOM FOOT ASSEMBLY SHOULD BE HELD AGAINST
THE VEHICLE IN ITS COMPLETELY OPEN POSITION. IT
IS IMPORTANT THAT THE BOTTOM GRAY RUBBER PADS
ARE INSTALLED ON THE VEHICLE IN A LOCATION
WHERE THERE IS PROPER SUPPORT.
FEET SHOULD NEVER BE INSTALLED ON GLASS
AKE SURE THAT THE BOTTOM AND SIDE STRAPS ARE
4. M
PROPERLY THREADED THROUGH PLASTIC BUCKLES.
OTTOM STRAPS: COMPLETELY HOOK BOTTOM HOOKS
5. B
TO A METAL EDGE BELOW BUMPER, OR AT THE BOTTOM
OF THE TRUNK/ REAR DOOR.
EDGE BELOW BUMPER, SEE ALTERNATE METHOD FOR
BOTTOM HOOK ATTACHMENT ON THE NEXT PAGE
OMPLETELY TIGHTEN BOTTOM STRAPS BY PULLING ON
6. C
FREE END OF STRAPS UNTIL ELASTIC PORTION OF
STRAPS ARE COMPLETELY STRETCHED.
IDE STRAPS: COMPLETELY HOOK SIDE HOOKS TO THE LEFT AND RIGHT OF REAR DOOR, AND
7. S
TIGHTEN STRAPS BY PULLING ON THE FREE END OF STRAP UNTIL THE ELASTIC PORTION OF S TRAP
IS COMPLETELY STRETCHED.
BE
CAREFUL THAT HOOKS DO NOT
CAUTION: Use Allen 104S only in accordance with local motor vehicle and traffic regulations.
To avoid damage to rear door or trunk, do not open trunk or
rear door when hooks or rack are in place.
Install rack and load bicycles only at a safe distance away
from moving traffic.
Only rubber feet of rack should come into contact with car.
Make sure that all of rack and bicycles are kept at a safe dis-
tance from road and hot exhaust.
Remove rack from car when not in use
NOTE: DRAWING BELOW SHOWS MODEL 102S
INDING
BOTTOM
.
.
.
C
THE
IF
THERE IS NO METAL
. B
ARFEULLY
Model 104S Instructions
English - Page 2
ALTERNATE METHOD #1 FOR
D.
BOTTOM STRAPS:
USE IF THERE IS NO METAL EDGE BELOW BUMPER FOR
ATTACHMENT OF HOOKS
REMOVE BOTTOM STRAPS FROM BOTTOM HORIZONTAL CROSS-BAR, AND
LOOP BOTTOM STRAP AROUND CARRY-ARMS NEAR TOP METAL BUCKLES.
TTACH HOOKS TO LOWER EDGE OF TRUNK/ REAR HATCH. TIGHTEN
A
NOTE: DRAWING BELOW SHOWS MODEL 102S
BOTTOM STRAP
HOOK
BOTTOM STRAPS.
F.
LOADING BICYCLES ON RACK:
1. REMOVE ALL LOOSE ITEMS FROM BICYCLES (PUMPS, BAGS, ETC.), AND CHECK THAT ALL QUICK RELEASE HUBS
ARE TIGHT.
2. L
OAD FIRST BICYCLE WITH ITS CHAIN AND GEARS FACING AWAY FROM RACK. MAKE SURE THAT BICYCLES DO
NOT COME IN CONTACT WITH VEHICLE.
3. L
OAD SUBSEQUENT BICYCLES IN ALTERNATING DIRECTIONS. FOR BEST WEIGHT DISTRIBUTION, LOAD HEAVIEST
BICYCLES FIRST, WITH LIGHTER BICYCLES ON THE OUTSIDE. ADD PADDING BETWEEN BICYCLE CONTACT
POINTS, IF NECESSARY.
4. A
FTER BICYCLES ARE LOADED, CHECK THAT ENTIRE RACK IS SECURE AND THAT THE RACK IS STILL FIRMLY IN
PLACE. VISION OUT OF REAR WINDOW MAY BE RESTRICTED—USE SIDE MIRRORS ACCORDINGLY WHEN BACKING
UP.
SPECIAL NOTE ON INSTALLING WOMEN’S STYLE FRAMES:
P
LACE ONE CARRY ARM UNDER FRONT TOP TUBE. WITH THE OTHER CARRY ARM, ROTATE TIE-DOWN CRADLE,
AND PLACE CARRY IN SPACE BEHIND SEAT TUBE AND BELOW REAR DOWN-STAY. THE ALLEN 900B ADAPTOR
B
AR IS ALSO RECOMMENDED FOR THIS APPLICATION.
G.
SECURING BIKES TO RACK:
1. PLACE BICYCLE IN
CRADLE.
ALL BIKES MUST BE SECURELY TIED TO RACK. USE INDIVIDUAL
TIE-DOWN STRAPS, OR ADDITIONAL STRAPS IF NECESSARY.
HREAD STRAPS.
2. T
ALTERNATE METHOD #2 FOR BOT-
E.
TOM
STRAPS:
USE IF THERE IS NO METAL EDGE BELOW BUMPER OR ON TRUNK
FOR ATTACHMENT OF HOOKS
BEFORE INSTALLING
RACK ON VEHICLE,
REMOVE BOTTOM
STRAPS OPEN TRUNK
SLIGHTLY AND PLACE
BOTTOM HOOKS JUST
INSIDE OF TRUNK/
HATCH. CAREFULLY
CLOSE TRUNK ON
BOTTOM STRAP.
P
ULL STRAPS TO
BRING HOOKS
OF TRUNK. MOUNT RACK ONTO CAR AS DESCRIBED IN SECTION C.
R
ETHREAD BOTTOM STRAPS AND TIGHTEN.
AGAINST THE INSIDE
3. PULL STRAP TIGHT.
I
F AN ALLEN BIKE RACK IS FOUND TO HAVE A DEFECT IN WORKMANSHIP OR MATERIAL OVER THE LIFETIME OF THE
ORIGINAL PURCHASER, ALLEN WILL REPAIR OR REPLACE THE RACK FREE OF CHARGE.
ALLEN LIFETIME WARRANTY:
R. A. ALLEN CO., INC.
505 B
EACHLAND BLVD.—SUITE 5
VERO BEACH, FL 32963
(800) 722-5536
FAX: (772) 234-5796
WWW.ALLENRACKS.COM - CUSTOMERSERVICE@ALLENRACKS.COM