Allen Sports 102AB User Manual

English Instructions

Allen

Model 102A Bike Rack

Pg. 1

WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury - do not use

rack on any vehicle on which it can not be properly mounted as described in this instruction sheet.

• Top hooks must be completely hooked over solid metal edges at top/front of trunk lid or rear door - never hook

to rain gutters, roof racks, vertical rear glass, rubber or plastic moldings.

• Mount rack only with bottom feet on a rigid surface of car (never on glass), and with bottom foot assembly

completely extended. Never use on trailers or front of vehicle.

•

Never carry more than 2 bikes (max. capacity: 70 lb.) - no tandems, mopeds, or recumbents. Bikes must be securely tied to rack - use excess strap extending from top metal buckles or additional straps if necessary. Car tail lights must remain visible.

• Drive conservatively, especially over bumps (never off-road). Check periodically during use that all straps are

tight and bikes are secure.

• Do not use if any part of rack is damaged or missing. Contact R. A. Allen Co., Inc. for replacement parts.

Caution: Use Allen 102A only in accordance with local motor vehicle and traffic regulations.

• To avoid damage to rear door or trunk, do not open trunk or rear door when hooks or rack are in place.

• Install rack and load bicycles only at a safe distance away from moving traffic.

•

Only rubber feet and hooks should come into contact with car. Do not allow metal parts of rack or bicycles to scratch car’s finish.

• Make sure that all of rack and bicycles are kept at a safe distance from road and hot exhaust.

• Remove rack from car when not in use.

Setting up

rack:

1. Fold out top-foot/ carry arm assembly.

2. Insert pins at ends of

wire struts into holes in top

foot assembly.

3. Completely fold out

bottom-foot assembly.

4. Set length of top straps to position rack with its carry-arms inclined slightly upwards (above the horizontal), and high enough to keep bikes away from road and exhaust [for drawing of rack on sedan style vehicle, see page 2 of instructions].

5. After length of top-strap is set, tie a half-hitch knot at

each metal buckle as shown in

Drawing A.

6. Once rack is installed, bottom foot

assembly must be held against

vehicle in its completely open

position.

Drawing

Note: Make sure that bottom straps

are threaded through plastic buckles only as shown in Drawing C.

7. Completely hook bottom hook to a

metal edge below the bumper or at the

bottom of the trunk.

8. Completely tighten bottom strap by pulling on free end of strap until elastic portion of strap is completely stretched. After straps are tightened, tie a half-hitch knot in each strap near the buckle.

Mounting rack on vehicle:

1. Make sure that contact surfaces between car and rubber feet are thoroughly clean and free of any dirt, and that all rubber feet remain

Drawing A

Note: It is okay to position top feet on glass; NEVER install rack with bottom

feet on glass.

properly spaced during use.

2. Only thread top straps through metal buckles as

shown in Drawing A. Never thread straps through fist slot in metal buckles as shown in

Drawing B.

3. Top hooks must be completely hooked over

solid metal edges at top of trunk, rear door, or hatchback. Never hook to rain gutters, roof racks, vertical rear glass or plastic moldings. Open

trunk/ hatch slightly for easiest attachment of

hooks. Be careful that hooks do not

bind when trunk/ hatch is opened or

closed.

3A. To secure top hooks on

vehicles without adequate clearance

at the top edge of rear trunk/ hatch: Un-

thread top straps from metal buckles and open rear trunk/ hatch. Place top hooks inside of vehicle (just inside of top edge of rear trunk/ hatch). Carefully close rear trunk/ hatch on top straps, making certain that hooks do not bind between frame and rear door. Important: with rear door closed, pull top straps to bring hooks up tight against inside of vehicle. Re-thread top straps through metal buckles as shown in Drawing A. Mount rack on vehicle.

Drawing B

Allen

Model 102A Bike Rack

English Instructions

Page 2.

Alternate method #1 for Bottom Strap:

Use if there is no metal edge below bumper for attachment of hooks.

Loop bottom strap around carry-arms near the top metal buckles. Attach hook to lower edge of rear trunk/ hatch; tighten straps as described in section B.

Mounting rack onto spare tires:

Never use rack on oversized tires, or trailers. Make sure that spare tire is securely mounted to vehicle and that it is fully inflated. Before mounting rack, remove any spare tire cover that may be damaged by rack.

Hook bike rack’s top-foot assembly over top of spare tire so that top feet are positioned completely behind tire. Top straps go down each side of tire. Secure all 3 hooks to a metal edge below spare tire. Completely tighten all straps. With off-center spare tires, make sure that bikes do not extend beyond side of car.

Alternate method #2 for Bottom Straps:

Use if there is no metal edge below bumper or on the trunk for

attachment of lower hooks.

Remove bottom strap from rack. Open trunk

slightly and place bottom hooks just inside

trunk/hatch. Carefully close trunk on

bottom strap. Pull strap to bring hook

against inside of trunk. Mount rack

onto car, rethread strap and tighten as described in section B.

Mounting rack onto pickup trucks:

Make sure that tailgate is securely latched.

Position top 2 rubber feet so that they will be against the top edge of the tailgate.

Hook rack’s top-foot assembly over tailgate. Secure all 3 hooks to bottom edge of tailgate, then completely tighten all straps.

Loading bicycles onto rack:

Remove all loose items from bikes (pumps, bags, etc.) and check that all quick-release hubs are tight.

Never carry more than 2 bikes (max. capacity: 70 lb..). Car tail lights must remain visible.

Load first bike with its chain and gears facing away from rack. Make sure that bikes do not come

into contact with car (rotate inside pedal if necessary). Place carry arm behind seat tube for

Load subsequent bikes in alternating directions. For best weight distribution, load heaviest bikes first

with lighter bikes on outside. Add padding between bike contact points, if necessary.

After bikes are loaded, check and retighten all straps, making sure that rack is still firmly held against car.

Vision out of rear window may be restricted - use side mirrors accordingly, especially when backing up.

Securing bikes to rack:

1. Loop excess of top strap around each bicycle and carry arm.

women’s style frames.

All bikes must be securely tied to rack. Use excess of top straps extending from knots tied at metal buckles, or use additional straps if necessary .

2. Tie a snug clove hitch knot at last (outside) bicycle.

3. Pull tight.

R. A. Allen Co., Inc. P. O. Box 221 Lincoln, MA 01773

U. S. Patents 4518108, 4709840, 5361959 - Foreign & Other Patents Pending

www.allenracks.com

Tel: (800) 722-5536

Fax: (781) 259-4116

email:customerservice@allenracks.com