This product is warranted to be free from defects in materials or
workmanship for period of one year from the date of purchase by the
original owner.
To ensure a high level of performance and reliability for which this
equipment has been designed and manufactured, read this User Guide
before operating. In the event of a failure, notify and return the
defective unit to ALLEN & HEATH Limited or its authorised agent as
soon as possible for repair under warranty subject to the following
conditions
Conditions Of Warranty
The equipment has been installed and operated in accordance with the
instructions in this User Guide.
The equipment has not been subject to misuse either intended or
accidental, neglect, or alteration other than as described in the User
Guide or Service Manual, or approved by ALLEN & HEATH.
Any necessary adjustment, alteration or repair has been carried out by
ALLEN & HEATH or its authorised agent.
This warranty does not cover fader wear and tear.
The defective unit is to be returned carriage prepaid to ALLEN &
HEATH or its authorised agent with proof of purchase.
Units returned should be packed to avoid transit damage.
In certain territories the terms may vary. Check with your ALLEN &
HEATH agent for any additional warranty which may apply.
This product complies with the European Electro magnetic Compatibility
directives 89/336/EEC & 92/31/EEC and the European Low Voltage
Directives 73/23/EEC & 93/68/EEC.
This product has been tested to EN55103 Parts 1 & 2 1996 for use in
Environments E1, E2, E3, and E4 to demonstrate compliance with the
protection requirements in the European EMC directive 89/336/EEC.
During some tests the specified performance figures of the product were
affected. This is considered permissible and the product has been passed as
acceptable for its intended use. Allen & Heath has a strict policy of
ensuring all products are tested to the latest safety and EMC standards.
Customers requiring more information about EMC and safety issues can
contact Allen & Heath.
Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
http://www.allen-heath.com http://www.xone.co.uk
Allen & Heath 2 XONE:S2 User Guide
PACKED ITEMS
Check that you have received the following:
Xone:S2mixer
Shorting
Jumper
USB
TO PC
LR
Mains Lead
Check that the correct
mains plug is fitted.
Safety Sheet
Important ! Read this sheet
before starting.
Retain for future reference.
Type A-B USB Lead
To connect the Xone:S2 to
your computer.
90 degree 3.5mm
jack adapter
Spare knobs
and buttons
Registration Card
Complete and return
to Allen & Heath to
register your product.
Allen & Heath 3 XONE:S2 User Guide
CONTENTS
Congratulations on purchasing the Allen & Heath Xone:S2 performance DJ
mixer. To ensure that you get the maximum benefit from the unit please
spare a few minutes familiarizing yourself with the controls and setup
procedures outlined in this user guide. For further information please
refer to the additional information available on our web site, or contact
our technical support team.
REPLACE FU SE WI TH SAME TYPE A N D
RATING.
UN DES MEMES CARACTERISTIQUES.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
+9dB
- 4d B
RLINEL
CAUTION
INPUT
1
0dB
CHANNEL 1
PHONOLR
+9dB
- 4d B
RLINEL
+IN
INSERT
MIC/LINE 2
MIC INPUT
2
INSERT
1
GND
- IN
TIP SEND
RING RETURN
INSERT
MIC/LINE 1
RLINEL
RLINEL
Front Panel
Fader Plates
USB
TO PC
LR
The Xone: S2 can be ordered with either rotary or linear
faders. The plates are interchangeable and can be ordered
separately.
Linear Fader Plate— Xone:S2-Linear
Rotary Fader Plate— Xone:S2-Rotary
Allen & Heath 5 XONE:S2 User Guide
INTRODUCTION TO THE XONE:S2
The Xone:S2 is a 19” rack mounted 4U analogue DJ mixer featuring four stereo dual input channels, two
Mono Mic/Stereo Line channels, and is available with either 45mm linear, or rotary VCA faders.
This mixer is designed for use in clubs, wine bars, and professional mobile DJ road shows, and incorporates many features to aid the installer, protect the sound system from overload, and enhance the DJs
performance. The Xone:S2 is the most feature laden 19” mixer available.
Each of the four main stereo channels is equipped with a high performance three band equalizer providing
a safe +6dB of boost and total kill for complete frequency isolation.
Nine point metering on each channel allows for precise matching of signal levels, and smooth VCA faders
help to ensure a perfect mix. Individual channels can be routed to either side of the high performance
VCA crossfader with adjustable curve control for smooth constant level mixes or virtually instant attack
suitable for scratching.
Two high quality MIC channels, each with two channel +/-15dB EQ, soft switched channel ON buttons,
insert points and smooth 60mm faders are included. These channels can also accept stereo line inputs.
The booth monitor is automatically ducked when a MIC channel is active, whist an adjustable voice over
control can be set to automatically duck the main music channels as soon as an announcement is made.
The Xone:S2 is also equipped with the legendary Xone Filter system. A rotary selector allows each of
the four main channels to be individually routed to the filter, or the filter can be set to “External” allowing
the filter to be connected to outboard equipment, or to be patched into the mixer insert point for global
filtering of the main mix.
Three basic filter types can be selected, hi-pass, band-pass and low-pass. These filter types can be added
together to create other filter types; e.g. hi-pass and low-pass together create a notch filter. Each filter
type can be swept from 20Hz to 20 kHz by the rotary frequency control, whilst resonance can be set
from “mild” to “wild”.
Uniquely on a mixer of this type, the Xone:S2 is equipped with a USB audio interface enabling easy integration of digital media. The USB interface can be used for playback and recording to/from the Xone:S2
and a computer, or can be patched into the mixer insert point and used like a hardware effects unit,
(with the appropriate software).
An additional stereo input (RCA) is accessible on the front panel enabling guest DJs to patch in additional
music sources without having to gain access to the rear connectors. This input is equipped with individual
level and cue controls.
The master section has individual controls for the main mix and booth, each with separate mono
switches. A global balance control can be used to correct source imbalance or as a panning effect.
Stereo nine point output meters display the post master level output, or the pre-fade source level when a
cue is selected. In split mode the left meter displays the cue level and the right meter the master output.
A powerful headphone amp ensures more than adequate monitor level, while no less than three separate
headphone sockets are provided; 3.5mm and ¼” Jack on the front panel and one ¼” Jack on the rear.
A split Cue feature allows the cue signal to be monitored in the left headphone and the main Mix in the
right.
Allen & Heath 6 XONE:S2 User Guide
SPECIFICATIONS
Input
RIAA input sensitivity 7-100mV 47K/330pF
Line Inputs -10dB to +15dB RCA
Mic Sensitivity -57 to –27dBu Balanced XLR
USB Audio In 0dBu RCA
Alarm Input 0dBu Phoenix connector
Mix Insert Return -2dBu RCA
Channel Insert Return 0dBu 1/4” TRS Jack
Filter External In 0dBu RCA
Output
Main Outputs +4dBu XLR
Monitor -2dBu RCA
Record -8dBu RCA
Zone +4dBu Balanced 1/4” TRS Jack
Operating Levels
Mono +4dBu Impedance Balanced XLR Sub Filter
Range 30Hz—250Hz
USB Audio Out 0dBu RCA
Mix Insert Send -2dBu RCA
Filter External Out 0dBu RCA
Channel Insert Send 0dBu 1/4” TRS Jack
Frequency response Line in to Mix out 10Hz to 20kHz +/- 0dB (-1.5dB @ 50kHz)
Distortion at 1kHz Line in at +0Vu out Typically < -0.05% Channel In to Mix out
Main Mix noise 22Hz—22kHz unweighted < -73 dBu (-77dB S/N)
The console is fitted with rubber feet for desktop operation.
Width Height Depth Weight
Mixer 482 mm (19“) 177 mm (7“) 123 mm (4.8”) 4.75 kg (10.5 lbs)
Packed 600 mm (23.6”) 300 mm (11.8”) 250 mm (9.8”) 7.5 kg (16.5 lbs)
Allen & Heath 7 XONE:S2 User Guide
XONE:S2
FADER START CCT
STEREO INPUTS
1,2,3,4
PHONO
R
L
RIAA
RIAA
LINE
DISABLE
R
L
MIC/LINE INPUTS
1,2
RTN
SND
INSERT
MIC
2= +
+
-
LINE
L
R
USB AUDIO
USB
TO PC
USB AUDIO IN
L
POST BALANCE L
POST BALANCE R
BLOCK DIAGRAM
LEVEL TRIM
LEVEL
LINE
L
LEVEL
2 BAND EQ
HI
LO
R
PHONO/LINE
MIC/LINE
EXTERNAL INPUT
AUDIO SOURCE
OPTION JUMPER
METER
3 BAND EQ
HF
OFF
+6
+
MF
OFF
+6
LF
OFF
+6
CUE
CUE
-15dB MONITOR DUCK DC
METER
+
CUE
LEVEL
FADER
ON
USB AUDIO INTERFACE
BLOCK DIAGRAM
FILTER MIX
CUE DC
CUE MIX
AUTO DUCK MIX
MONITOR DUCK DC
ALARM DC
LIMIT DC
DUCK DC
Y DC
X DC
FILTER SELECT DC
ROTARY
OPTION
FADER
+
CROSSFADER
X Y SELECT
DC
VCA
FILTER ACTIVE
LEVEL
CUE
USB AUDIO OUT
LR
-2dBu
R
LR MIX VCA
LR MIX
FILTER EXTERNAL
INPUT
SELECT DC
FILTER MIX
ASSIGNMENT
CH 4
CH 3
CH 2
CH 1
RESONANCE
FREQ
FILTER
DISABLE
FILTER EXTERNAL OUTPUT
LR MIX
VCA
DUCK MIX
ALARM DC
CUE DC
CUE MIX
CURVE
X / Y DC
EXTERNAL DC
FILTER
EXTERNAL
HPF
BPF
LPF
ON
EXTERNAL ACTIVE
FX LOOP ON
FX INSERT
LIMIT DC
THRESHHOLD
Adj + 6dB - + 18d B
DUCKING CCT
RELEASE SPEED
FAST/SLOW
OFF
DUCK ACTIVE (ALARM)
DEPTH
ALARM OVERRIDE SWITCHED INPU T
EXTERNAL ALARM MESSAGE
XY
CROSSFADER
RECORD OUT
-15dB MONITOR DUCK DC
BALANCE
LEVEL DETECT CCT
CUE ACTIVE
PRE MASTER
LEVEL
-10dBV
LIMITER ON
L
R
MONITOR
LR SUM
+
SPLIT CUE
VCA
EXT LEVEL CONTROL
POST BALANCE L
POST BALANCE R
MONO
MONO
MIX
LR SUM
+
L
R
BAL
AUDIO LIGHT FEED
TO USB
INTERFACE
BAL
SUB FILTER
Adj 30Hz - 250Hz
SUB ON
HEADPHONES
2= +
+4dBu
2= +
REMOTE
L
MONITOR
-2dBu
R
2=+
+4dBu
2=+
+4dBu
MASTER
METERS
L
R
PHONES 1/4"
L
R
PHONES 1/4"
L
R
PHONES 3.5mm
L
ZONE
OUT
R
0- 10 VOLTS
-2dBu
OUT
L
MIX
OUT
R
MONO
OUT
Allen & Heath 8 XONE:S2 User Guide
MIC / LINE INPUT CHANNEL
5
3
1
2
4
1
2
3
Mic Input Socket
Standard 3-Pin XLR socket wired as Pin 1 = Ground, Pin
2 = hot (+), Pin 3 = cold (-).
Mic / Line Select Switch
Selects either the XLR microphone input or the alternative RCA stereo line input. In the up position MIC is
selected, when pressed LINE is selected.
Channel Level Control
This control has a range of -∞ to +9dB for LINE inputs
and a range of -57 dBU to –27dBu for MIC inputs. Use
it to adjust the signal level of an audio source to give a
nominal 0dB reading on the channel meter, with the
peak level at or below 6dB. Turn LEVEL down if the
+10 peak meter starts flashing.
4
5
Channel Equaliser
The Mic/Line input channel is equipped with a 2 band EQ
stage providing +15dB of boost when fully clockwise and
–15dB attenuation when fully anti-clockwise.
Cue Switch
Press the Cue switch to listen to the channel pre-fade
signal in the headphones and see its level on the main
meters. The LED indicator next to the switch lights
when selected. The Cue LED indicator in the monitor
section also lights to warn that you are monitoring the
channel signal rather than the main mix. Press the
switch to deselect cue.
Allen & Heath 9 XONE:S2 User Guide
MIC / LINE INPUT CHANNEL
6
8
7
6
7
8
Channel Meter
Displays the channel signal level. It is post EQ and prefader. This means it is not affected by the fader position.
The channel level control should be set so that the meter averages around ‘0’ with loudest peaks no higher
than ‘+6’. Turn down the level control if the +10 peak
indicator lights.
Channel Fader
60mm smooth travel fader adjusts the channel signal
level from fully off to fully on.
Mic On Switch
Press the Mic switch to send the channel audio to the
mix. When selected, the LED indicator switch will illuminate yellow and the monitor output will be automatically ducked by –15dB.
The Mic On switch has two operating modes—single
press or press and hold. When the switch senses a single press it will latch the channel on, when it senses a
press and hold it will turn the channel off when the
switch is released. This operation is ideal for making
short announcements.
Allen & Heath 10 XONE:S2 User
PHONO / LINE INPUT CHANNEL
5
6
4
2
1
3
1
2
3
Phono / Line Select Switch
Selects either the RCA phono input or the alternative
RCA stereo line input. In the up position PHONO is
selected, when pressed LINE is selected.
Channel Level Control
This control has a range of –10 to +4dB dependant upon
the channel trim. Use it to adjust the signal level of an
audio source to give a nominal 0dB reading on the channel meter, with the peak level at or below 6dB. Turn
LEVEL down if the +10 peak meter starts flashing.
Channel Equalizer / Isolator
The Xone:S2 is equipped with a very powerful 3 band
EQ stage providing a controlled +6dB of boost when
fully clockwise, but full isolation (cut) of each band for
dramatic effect when fully anti-clockwise. Centre
frequencies are set at:
The Filter On LED will illuminate when the filter is assigned to the selected channel.
Cue Switch
Press the Cue switch to listen to the channel pre-fade
signal in the headphones and see its level on the main
meters. The LED indicator next to the switch lights
when selected. The Cue LED indicator in the monitor
section also lights to warn that you are monitoring the
channel signal rather than the main mix. Press the
switch to deselect cue.
Allen & Heath 11 XONE:S2 User
PHONO / LINE INPUT CHANNEL
Channel Meter
6
Displays the channel signal level. It is pre-EQ and prefader, allowing the input level to be displayed even if the
EQ is set to off on all bands. To view the post EQ level,
press the cue switch and use the mix/monitor meters.
The channel level control should be set so that the meter averages around ‘0’ with loudest peaks no higher
than ‘+6’. Turn down the level control if the +10 peak
indicator lights.
8
7
7
8
Channel Fader
A high quality, 45mm smooth travel dual-rail fader or
rotary potentiometer adjusts the channel signal level
from fully off to fully on.
XFade Switch
Used to assign the channel to either the X (left) or Y
(right) side of the cross-fader. Works in conjunction
with the XFADER On switch in the master section.
A bi-colour LED indicator illuminates either red (X) or
yellow (Y) to show which side of the cross-fader has
been selected.
Allen & Heath 12 XONE:S2 User
FILTER SECTION
2
3
4
5
1
1
2
Filter Assign Selector
Selects the channel to be routed through the filter. The
FILTER LED in the selected channel section will light
when selected. The EXTERNAL LED will light when the
selector is set to EXTERNAL.
NOTE: To prevent accidental assignment of the filter
there is a delay when selecting an individual channel. For
smoothest operation, use the filter on/off button before
selecting another channel rather than relying on the
switching delay.
Resonance Control
This produces the classic analogue VCF sound by feeding
some of the filter output back to its input. The control
ranges from ‘mild’ producing a very subtle effect, to
‘wild’ producing a dramatic phase effect with feedback
just short of oscillation.
3
4
5
HPF Button
Turns on the high pass (bass cut) filter slope. The light
ring around the button illuminates when selected.
BPF Button
Turns on the band pass (bell shaped) filter slope. The
light ring around the button illuminates when selected.
LPF Button
Turns on the low pass (treble cut) filter slope. The light
ring around the button illuminates when selected.
Allen & Heath 13 XONE:S2 User
FILTER SECTION
6
7
Frequency Sweep Control
This control sets the –3dB cut-off frequency of the filter.
It ranges from very low frequency (20Hz) to very high
frequency (20kHz).
NOTE: Both BPF and HPF filters are band limited to
prevent them going above 10kHz.
Filter On Switch
Switches the filter on and off. The light ring around the
button illuminates when the filter is active.
The Filter On switch has two operating modes—single
press or press and hold. When the switch senses a single press it will latch the filter on, when it senses a press
and hold it will turn the filter off when the switch is released.
6
7
Allen & Heath 14 XONE:S2 User
USB / HEADPHONE SECTION
1
4
USB
TO PC
2
3
1
2
USB Connector
USB (Universal Serial Bus) V1.1 is an external peripheral
interface standard for data transmission. Xone:S2 USB
works at 12Mbps and provides two stereo uncompressed audio channels. It is fully compatible with USB2.
The USB connection is used to send and receive audio
data between the Xone:S2 and a connected computer.
Use a standard type A to B lead to connect to your
computer.
In the default configuration, the USB input to PC is from
the RCA Phono connectors on the rear of the mixer.
Internal option links can be set to change this to the
pre-fade mix output.
Headphone Outputs
Stereo 1/4” TRS jack and 3.5mm mini-jack. Plug in good
quality stereo headphones intended for DJ monitoring.
Use closed-ear headphones that provide maximum
acoustic isolation when cueing your sources. We recommend that you use high quality headphones rated between 30 to 100 ohms impedance. 8 ohm headphones
are not recommended.
3
4
USB Cue Switch
Press the USB Cue switch to listen to the USB pre-level
signal in the headphones and see its level on the main
meters. The Cue LED indicator in the monitor section
lights to warn that you are monitoring the USB signal
rather than the main mix. Press the switch to deselect
cue.
USB Level Control
Sets the level of the USB signal. The USB level control
ranges from -∞ to +6dB based on the input level and is
sent to the main LR mix.
Allen & Heath 15 XONE:S2 User
USB / HEADPHONE SECTION
USB
TO PC
5
Headphone Level Control
Adjusts the level of the headphone signal.
82!
6
Split Cue Switch
Press the Split Cue Switch to activate split cue mode. In
split cue mode the cue signal is fed to the left side of the
headphones and is displayed on the left output meter.
The mix remains in the right ear and its level is displayed
on the right output meter.
The Split Cue LED will light when in split cue mode.
Warning ! To avoid damage to your
hearing do not operate the headphones
or sound system at excessively high
volume. Continued exposure to high
volume sound can cause frequency
selective or wide range hearing loss.
5
6
7
7
Cue Active LED
The Cue active LED will light when any channel or input
cue button is selected.
Allen & Heath 16 XONE:S2 User
HEADPHONE CABLE CLIPS
1
LR
Wire Clips
1
Two wire clips are provided for the purpose of securing the headphone cabling
away from the front panel controls of the mixer.
NOTE: A third headphone socket is available on the rear of the mixer. This
connection may be used for mounting a headphone extension lead into a blank
19” panel underneath the mixer in a fixed installation.
1
Allen & Heath 17 XONE:S2 User
EXTERNAL INPUT / AUTO DUCK / EFFECT LOOP
External Input Sockets
LR
1
1
Front-panel mounted stereo RCA sockets for easy connection of external line level audio sources.
External Input Level Control
2
The external input level control ranges from -∞ to +6dB
based on the input level.
2
4
5
3
4
5
External Input Cue Switch
Press the external input cue switch to listen to the external input pre-level signal in the headphones and see
its level on the main meters. The Cue LED indicator in
the monitor section lights to warn that you are monitoring the external input signal rather than the main mix.
Press the switch to deselect cue.
Mic Auto Duck Level
Selects the level of ducking on the music channels when
a signal is present on the microphone inputs. Ranges
from no attenuation (fully anti-clockwise) to –15dB of
attenuation (fully clockwise).
Fast / Slow Release Switch
Changes the time taken for the main audio channels to
return to their normal level after the DJ has finished
speaking.
Use a fast release time for quick punchy announcements
and slow release for more relaxed talk overs.
Allen & Heath 18 XONE:S2 User
EXTERNAL INPUT / AUTO DUCK / EFFECT LOOP
6
LR
6
7
Ducker Active LED
Lights when the main outputs are being ducked. Also
lights when the external alarm input switch closure is
active.
Effect Loop Switch
Switches in the FX insert circuit. The LED indicator
around the switch lights when selected.
NOTE: If nothing is connected to the insert connectors,
switching on the FX loop will break the main audio signal path.
7
Allen & Heath 19 XONE:S2 User
1
2
3
MASTER SECTION
Mix / Monitor Meters
1
The main meters follow the selected monitor source.
The default display is the post master level, which is
overridden with an input channel level if the channel cue
switch is selected.
In split cue mode, the left master meter will display the
cued channel signal level and the right master meter will
display the mix level. The cued mix audio is pre level to
prevent mismatch due to the position of the master
level control.
The mixer should be operated with these meters averaging around ‘0’ with loudest peaks no higher than ‘+6’.
4
5
2
3
4
Output Limit Active LED
If the output limiter has been engaged this LED will illuminate to indicate that the threshold has been exceeded
and the limiter is active. The limiter is POST the Master
Level control.
Mix Master Level Control
A rotary master control adjusts the level of the main
mix XLR outputs feeding the house sound system. This
does not affect the monitor output or the meter reading.
Mix Mono Switch
Sums the left and right signal levels to produce a mono
mix from both outputs.
5
Allen & Heath 20 XONE:S2 User
Monitor Master Level Control
Adjusts the level of the signal to the stereo monitor
RCA output. This does not affect the headphones. The
monitor output could be used for a booth monitor, recording or an additional zone feed.
MASTER SECTION
6
6
7
Monitor Mono Switch
Sums the left and right signal levels to produce a mono
mix from both outputs.
Balance Control
Use to compensate for poor signal balance between left
and right or as a panning effect. The balance control is
disabled if the outputs are set to mono.
7
Allen & Heath 21 XONE:S2 User
CROSSFADER
1
2
3
Crossfader Curve Control
1
This control adjusts the crossfader curve between dipped response, ideal for
seamless beat mixing, and fast-attack, suitable for scratch or cut mixing .
Crossfader On Switch
2
In its normal (out) position the crossfader is active. Push the switch to turn the
crossfader off—the channel LED indication will also be switched off.
Crossfader
3
This lets you fade between signals routed to either side, typically to fade
smoothly into a new music track or to creatively layer sounds when scratch or
cut mixing.
The crossfader is a VCA controller which affects the level of signals routed via
the filters. Make sure the toggle switches on the channels you wish to fade are
set to X or Y as appropriate.
Please contact your Allen and Heath approved service centre for crossfader service or replacement.
Allen & Heath 22 XONE:S2 User
1 2 3 4 5
OUTPU T LIM ITER
MONITOR
LR
RECOR D
MIX OUT
+10
+12
LEFT
RIGHT
+6+8
+18
LEFT
+4dBu
OUTPUT
THRESHOLD
dBu
RIGHT
+4dBu
-2dBu
-10dBV
(-8dBu)
PRE MAST ER LEVEL
ZONE OUT
DO NOT SHORT RING TO GROUND
FOR UNBALA NCED OPERATION
CONNECT TO TIP ONLY
FADER STA RT 4FADER START 3FA DE R STA R T 2FADE R STA RT 1
HEAD PH ONE 3
LEVEL TRIM 4LEVEL TRIM 3LEVEL TRIM 2LEVEL TRI M 1
AUDIO LIGHT FEE D
EXTERNAL
RL
SERIAL No:
FILTER
OUTLR
+9dB
0dB
- 4dB
CHANNEL 4
PHONOLR
INP UT
4
AC MAINS IN ~
100 - 240V~
47-63Hz ~ 30W MAX
RLINEL
MADE IN THE UK BY ALLEN & HEATH LIMITED
RINL
0
OFF
I
ON
CHANNEL 3
INP UT
3
T500mAL 250V 20mm
0dB
PHONOLR
FUSE
+9dB
- 4dB
RLINEL
INP UT
2
CHANNEL 2
+9dB
0dB
- 4dB
PHONOLR
RLINEL
REPLACE FUSE WITH SAME TYPE
AND RATING.
UN DES MEMES
CARACTERISTIQUES.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
CAUTION
INPUT
1
0dB
CHANNEL 1
PHONOLR
+9dB
MIC INPUT
1
2
+IN
GND
- IN
INSERT
TIP SEND
RING RETURN
INSERT
- 4dB
MIC/LINE 2
RLINEL
RLINEL
INSERT
MIC/LINE 1
RLINEL
1
2
3
4
Mix Output
Balanced XLR. This is the main output that feeds the house PA system. Plug into the house
processor/amplifier system using balanced cables. Use balanced cables and equipment.
When the main meter LEDs are at “0dB” the output will nominally be at +4dBu. Do not
unbalance this output by shorting one phase to ground—for unbalanced operation use pin 2
only.
Output Threshold Selector
Sets the output threshold level - adjustable from +6 to +18 dBu. This control is a recessed
preset pot—use a thin flat blade screwdriver to adjust. Turning the pot clockwise increases
the sensitivity of the limiter and reduces the maximum output level.
Output Limiter Switch
Using a thin screwdriver, pressing this recessed switch turns the output limiter on.
Mono Output
Impedance balanced XLR nominal +4dBu. The mono output can also be configured to be a
sub bass output. This output follows the master level control.
5
Sub Filter Switch
Pressing this recessed switch engages a 12dB/Oct low pass filter making this output ideal as a
feed for a sub bass system.
Allen & Heath 23 XONE:S2 User
REAR CONNECTORS
6
7 8 9 10
+OUT
2
DO NOT SHORT PIN 3 TO GROUND
-OUT
FOR UNBALANCED OPERATION
CONNECT TO PIN 2 ONLY
GND
1
USB AUDIO
OUT
LR
IN
CW
5KRD
HEAD PH ONE 3
AUDIO LIGHT FEE D
EXTERNAL
RL
SERIAL No:
FILTER
OUTLR
RINL
0
OFF
I
ON
FADER STA RT 4FADER START 3FA DE R STA R T 2FADE R STA RT 1
LEVEL TRIM 4LEVEL TRIM 3LEVEL TRIM 2LEVEL TRI M 1
+9dB
0dB
- 4dB
CHANNEL 4
INP UT
4
AC MAINS IN ~
100 - 240V~
47-63Hz ~ 30W MAX
PHONOLR
CHANNEL 3
INP UT
3
RLINEL
T500mAL 250V 20mm
MADE IN THE UK BY ALLEN & HEATH LIMITED
0dB
PHONOLR
FUSE
+9dB
- 4dB
RLINEL
+9dB
0dB
- 4dB
CHANNEL 2
PHONOLR
INP UT
2
RLINEL
REPLACE FUSE WITH SAME TYPE
AND RATING.
UN DES MEMES
CARACTERISTIQUES.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
CAUTION
INPUT
1
0dB
CHANNEL 1
PHONOLR
+9dB
MIC INPUT
1
2
+IN
GND
- IN
INSERT
TIP SEND
RING RETURN
INSERT
- 4dB
MIC/LINE 2
RLINEL
RLINEL
OUTPU T LIM ITER
MONITOR
LR
RECOR D
MIX OUT
+10
+12
LEFT
RIGHT
LEFT
+4dBu
OUTPUT
+6+8
THRESHOLD
+18
dBu
RIGHT
+4dBu
-2dBu
-10dBV
(-8dBu)
PRE MAST ER LEVEL
SUB FILTER
150Hz
120Hz
90Hz
FX INSERT
ZONE OUT
TIP +
TIP
+4dBu
RING -
RING
DO NOT SHORT RING TO GROUND
FOR UNBALA NCED OPERATION
CONNECT TO TIP ONLY
This sets the crossover point of the low pass filter allowing tuning of the sub bass system.
The (-3dB) cut off point can be set between 30Hz and 250Hz. A graduated scale shows the
approximate cut off point.
INSERT
MIC/LINE 1
RLINEL
7
8
9
10
Headphone 3
Third headphone socket, stereo 1/4” TRS jack.
Sound To Light
A high impedance, ground isolated mono output designed to provide an audio feed for lighting systems.
Channel Level Trim
This recessed control trims the channel pre-amplifier gain level to prevent overload of the
PA, or to adjust to special input levels. This control works in conjunction with the front
panel level control.
For instance with the trim fully anti-clockwise (-4) and the level fully clockwise (+4) the
maximum channel gain will be 0dB (unity).
Channel Fader Start
3.5mm TRS jack follows the convention of Start—tip pulsed high and Stop—sleeve pulsed
high, as used in products such as the Pioneer CDJ series.
Allen & Heath 24 XONE:S2 User
REAR CONNECTORS
11 12 13
+OUT
2
DO NOT SHORT PIN 3 TO GROUND
-OUT
OUTPU T LIM ITER
MONITOR
LR
RECOR D
MIX OUT
+10
+12
LEFT
RIGHT
LEFT
+4dBu
OUTPUT
+6+8
THRESHOLD
+18
dBu
RIGHT
+4dBu
-2dBu
-10dBV
(-8dBu)
PRE MAST ER LEVEL
SUB FILTER
150Hz
120Hz
90Hz
FX INSERT
ZONE OUT
TIP +
TIP
+4dBu
RING -
RING
DO NOT SHORT RING TO GROUND
FOR UNBALA NCED OPERATION
CONNECT TO TIP ONLY
FADER STA RT 4FADER START 3FA DE R STA R T 2FADE R STA RT 1
LEVEL TRIM 4LEVEL TRIM 3LEVEL TRIM 2LEVEL TRI M 1
+9dB
0dB
- 4dB
CHANNEL 4
PHONOLR
INP UT
4
AC MAINS IN ~
100 - 240V~
47-63Hz ~ 30W MAX
RLINEL
MADE IN THE UK BY ALLEN & HEATH LIMITED
RINL
OFF
ON
CHANNEL 3
INP UT
3
T500mAL 250V 20mm
0dB
PHONOLR
FUSE
+9dB
- 4dB
RLINEL
+9dB
0dB
- 4dB
CHANNEL 2
PHONOLR
INP UT
2
RLINEL
REPLACE FUSE WITH SAME TYPE
AND RATING.
UN DES MEMES
CARACTERISTIQUES.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
CAUTION
INPUT
1
0dB
CHANNEL 1
PHONOLR
+9dB
- 4dB
RLINEL
+IN
INSERT
MIC/LINE 2
MIC INPUT
2
INSERT
1
GND
- IN
TIP SEND
RING RETURN
INSERT
MIC/LINE 1
RLINEL
RLINEL
11
12
13
Monitor Output
RCA phono (–2dBu nominal). Provides a line level stereo feed to the DJ local monitor amplifier system. It is not affected by the master fader or cue system.
FX Insert Point
RCA phono. Provides for insertion of effects into the main out audio path. Selected using
the FX Loop On switch.
NOTE: If nothing is connected to the insert, selecting the FX Loop on will break the main
signal path. Always fit the supplied shorting jumpers if the insert isn’t being used—the insert
send is always active.
USB Audio I/O
RCA phono. Allows external connection to USB interface. Internal link option sets the USB
to internal post balance pre level mix out if required. The default setting is for external input allowing the USB interface to be connected to the insert point and used as an effects
unit with suitable software (such as Ableton Live). To record a mix using the USB In, connect to either the Record Out socket or the FX Send.
The USB interface is compatible with Windows™ 98/98SE, ME, WIN2000 and XP, MAC
OS9.1, OSX (10.0) or later (but not Japanese OS 10.1).
For lowest latency with Windows, an ASIO driver is recommended such as ASIO4ALL by
Michael Tippach — www.asio4all.com
Allen & Heath 25 XONE:S2 User
REAR CONNECTORS
MONITOR
MONITOR
RECOR D
RECOR D
14
MIX OUT
MIX OUT
+10
+10
+12
+12
OUTPU T LIM ITER
OUTPU T LIM ITER
LR
LR
LEFT
LEFT
RIGHT
RIGHT
LEFT
LEFT
+4dBu
+4dBu
OUTPUT
OUTPUT
+6+8
+6+8
THRESHOLD
THRESHOLD
+18
+18
dBu
dBu
RIGHT
RIGHT
+4dBu
+4dBu
-2dBu
-2dBu
-10dBV
-10dBV
(-8dBu)
(-8dBu)
PRE MAST ER LEVEL
PRE MAST ER LEVEL
SUB FILTER
SUB FILTER
150Hz
150Hz
120Hz
120Hz
90Hz
90Hz
FX INSERT
FX INSERT
ZONE OUT
ZONE OUT
TIP +
TIP
TIP +
TIP
+4dBu
+4dBu
RING -
RING
RING -
RING
DO NOT SHORT RING TO GROUND
DO NOT SHORT RING TO GROUND
FOR UNBALA NCED OPERATION
FOR UNBALA NCED OPERATION
CONNECT TO TIP ONLY
CONNECT TO TIP ONLY
ZONE OUT
ZONE OUT
MON O
MON O
FREQUE NC Y
FREQUE NC Y
SENDLR
SENDLR
+4dBu
+4dBu
250Hz
250Hz
30Hz
30Hz
50Hz
50Hz
RRTNL
RRTNL
EXT LEVEL CTRL
EXT LEVEL CTRL
ALARM INPUT
ALARM INPUT
ALARM
ALARM
ALARM N/O
ALARM N/O
ALARM AUDIO
ALARM AUDIO
+10V EXT
+10V EXT
LEVEL 0 -10V
LEVEL 0 -10V
EXT
EXT
+OUT
+OUT
2
2
DO NOT SHORT PIN 3 TO GROUND
DO NOT SHORT PIN 3 TO GROUND
-OUT
-OUT
FOR UNBALANCED OPERATION
FOR UNBALANCED OPERATION
CONNECT TO PIN 2 ONLY
CONNECT TO PIN 2 ONLY
GND
GND
1
1
USB AUDIO
USB AUDIO
OUT
OUT
LR
LR
IN
IN
CW
CW
5KRD
5KRD
14 15
HEAD PH ONE 3
HEAD PH ONE 3
AUDIO LIGHT FEE D
AUDIO LIGHT FEE D
FILTER
FILTER
EXTERNAL
EXTERNAL
OUTLR
OUTLR
INP UT
INP UT
4
4
RL
RL
SERIAL No:
SERIAL No:
RINL
RINL
AC MAINS IN ~
0
0
I
I
AC MAINS IN ~
OFF
OFF
ON
ON
100 - 240V~
100 - 240V~
47-63Hz ~ 30W MAX
47-63Hz ~ 30W MAX
FADER STA RT 4FADER START 3FA DE R STA R T 2FADE R STA RT 1
FADER STA RT 4FADER START 3FA DE R STA R T 2FADE R STA RT 1
LEVEL TRIM 4LEVEL TRIM 3LEVEL TRIM 2LEVEL TRI M 1
LEVEL TRIM 4LEVEL TRIM 3LEVEL TRIM 2LEVEL TRI M 1
+9dB
+9dB
0dB
0dB
- 4dB
- 4dB
CHANNEL 4
CHANNEL 4
PHONOLR
PHONOLR
RLINEL
RLINEL
MADE IN THE UK BY ALLEN & HEATH LIMITED
MADE IN THE UK BY ALLEN & HEATH LIMITED
CHANNEL 3
CHANNEL 3
INP UT
INP UT
3
3
T500mAL 250V 20mm
T500mAL 250V 20mm
0dB
0dB
PHONOLR
PHONOLR
FUSE
FUSE
+9dB
+9dB
- 4dB
- 4dB
RLINEL
RLINEL
+9dB
+9dB
0dB
0dB
- 4dB
- 4dB
CHANNEL 2
CHANNEL 2
PHONOLR
PHONOLR
INP UT
INP UT
2
2
RLINEL
RLINEL
REPLACE FUSE WITH SAME TYPE
REPLACE FUSE WITH SAME TYPE
AND RATING.
AND RATING.
UN DES MEMES
UN DES MEMES
CARACTERISTIQUES.
CARACTERISTIQUES.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
CAUTION
CAUTION
INPUT
INPUT
1
1
0dB
0dB
CHANNEL 1
CHANNEL 1
PHONOLR
PHONOLR
16 17
+9dB
+9dB
- 4dB
- 4dB
RLINEL
RLINEL
+IN
+IN
INSERT
INSERT
MIC/LINE 2
MIC/LINE 2
MIC INPUT
MIC INPUT
2
2
INSERT
INSERT
1
1
GND
GND
- IN
- IN
TIP SEND
TIP SEND
RING RETURN
RING RETURN
RLINEL
RLINEL
Filter External I/O
RCA Phono. Allows external connection to the filter circuitry. External source selected
using Filter Assignment Selector. To use the filter as a global effect, patch the external filter
sockets into the FX Insert points (Send to Filter In, Return to Filter Out).
INSERT
INSERT
MIC/LINE 1
MIC/LINE 1
RLINEL
RLINEL
18
15
16
17
CH 1-4 Phono Input
RCA phono 7 –100 mV 47k impedance 380 pF. Plug in turntables with magnetic cartridges
requiring RIAA equalisation. For non-RIAA turntables plug into the LINE input instead. Do
not plug in line level sources to the phono inputs as these will overload the preamp and
cause severe high level distortion.
Mic / Line Channel Line Input
Stereo RCA Phono input for line source on Mic / Line channels. Connect stereo line level
music sources such as CD, MD, DAT, drum machines, keyboards or other instruments. Do
not connect turntables which require RIAA equalisation.
Chassis Earth Terminal
A screw terminal is provided for connecting the earth straps from turntables. This connection earths the metal parts of the turntable to reduce hum, buzz or similar audible noise getting into the system.
18
Mic Channel Insert Point
An insert point is provided on the Mic Input Channels wired as Tip (send) and Ring (return)
on a 1/4” TRS jack.
Allen & Heath 26 XONE:S2 User
REAR CONNECTORS
19
19
OUTPU T LIM ITER
MONITOR
LR
RECOR D
MIX OUT
+10
+12
LEFT
RIGHT
LEFT
+4dBu
OUTPUT
+6+8
THRESHOLD
+18
dBu
RIGHT
+4dBu
-2dBu
-10dBV
(-8dBu)
PRE MAST ER LEVEL
SUB FILTER
150Hz
120Hz
90Hz
FX INSERT
ZONE OUT
TIP +
TIP
+4dBu
RING -
RING
DO NOT SHORT RING TO GROUND
FOR UNBALA NCED OPERATION
CONNECT TO TIP ONLY
FADER STA RT 4FADER START 3FA DE R STA R T 2FADE R STA RT 1
LEVEL TRIM 4LEVEL TRIM 3LEVEL TRIM 2LEVEL TRI M 1
+9dB
0dB
- 4dB
CHANNEL 4
PHONOLR
INP UT
4
RINL
AC MAINS IN ~
OFF
ON
100 - 240V~
47-63Hz ~ 30W MAX
INP UT
3
RLINEL
MADE IN THE UK BY ALLEN & HEATH LIMITED
0dB
CHANNEL 3
PHONOLR
FUSE
T500mAL 250V 20mm
21
+9dB
- 4dB
RLINEL
+9dB
0dB
- 4dB
CHANNEL 2
PHONOLR
INP UT
2
RLINEL
REPLACE FUSE WITH SAME TYPE
AND RATING.
UN DES MEMES
CARACTERISTIQUES.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE.
CAUTION
INPUT
1
0dB
CHANNEL 1
PHONOLR
+9dB
MIC INPUT
2
+IN
- IN
INSERT
INSERT
- 4dB
MIC/LINE 2
RLINEL
RLINEL
Record Output
RCA Phono, nominal –10dBv (-8dBu). Pre-level mix output for connection to external recording devices.
1
GND
TIP SEND
RING RETURN
INSERT
MIC/LINE 1
RLINEL
20
21
AC Mains Input
IEC cable with moulded mains plug suitable for your local supply.
Important: Read the SAFETY INSTRUCTIONS sheet included with the
Xone:S2 and printed on the rear panel.
Check that the correct mains lead with moulded plug has been supplied with your console.
The power supply accepts mains voltages within the range 100-240V without changing any
fuses or settings. Ensure that the IEC mains plug is pressed fully into the rear panel socket
before switching on.
Note: It is standard practice to turn connected power amplifiers down or off before
switching the console on or off. This prevents any potential damage to speaker systems due
to switch-on transients.
CH 1-4 Line Input
RCA phono. Connect stereo line level music sources such as CD, MD, DAT, drum machines, keyboards or other instruments. Do not connect turntables which require RIAA
equalisation. Alternatively, you can connect to jack sources using a cable with RCA to jack
adapters. Avoid using low grade cables such as those often supplied with domestic equipment as these can quickly prove unreliable in use.
Allen & Heath 27 XONE:S2 User
REAR CONNECTORS - ZONE OUT
22 23
LEFT
RIGHT
22
Zone Output
Balanced TRS Jack outputs for separate zone—nominal +4dBu. This output is ideal for feeding a separate room or bar area.
Do not unbalance this output by shorting one phase to ground. For unbalanced operation
connect to Tip only.
PRE MASTER LEVE L
ZONE OUT
TIP +
TIP
+4dBu
RING -
RING
DO NOT SHORT RING TO GROUND
FOR UNBALANCED OPERATI ON
CONNECT TO TIP ONLY
ZONE OUT
24 25
EXT LEVEL CTRL
ALARM INPUT
ALARM
ALARM N/ O
ALARM AUDIO
+ 10V EXT
L EVEL 0 -10V
EXT
CW
5KRD
23
24
25
Zone Pre Master Level Switch
Set this switch to source the zone output Pre Master level so that the level is not affected by
the Master level control.
Zone External Level Control Switch
Set this switch to engage the external level control circuitry. If external control is not connected this will mute the zone output.
External Level Control
The zone output can be easily remote controlled with a simple three-wire interface to a
suitable potentiometer. Almost any potentiometer will work but for the best control we
recommend a 5kΩ Reverse Log Law. The external
+10V EXT
LEVEL
0-10V
control will also interface with any controller that
follows the standard 0-10V convention such as
AMX ™ or Crestron™ controllers.
EXT
Allen & Heath 28 XONE:S2 User
REAR CONNECTORS - ZONE OUT
26 27
26
LEFT
RIGHT
PRE MASTER LEVE L
ZONE OUT
TIP +
TIP
+4dBu
RING -
RING
DO NOT SHORT RING TO GROUND
FOR UNBALANCED OPERATI ON
CONNECT TO TIP ONLY
EXT LEVEL CTRL
ALARM INPUT
ALARM
ALARM N/ O
ALARM AUDIO
+ 10V EXT
CW
L EVEL 0 -10V
EXT
5KRD
ZONE OUT
Alarm Override Switch Input
To interface to safety alarm systems , shorting these two connections together will mute the
four main music channels but leave the Mic channels open. The Duck LED on the front
panel also illuminates to show that the alarm has been activated.
27
External Alarm Audio
High impedance input for interfacing to a pre-recorded safety message (0dBu nominal).
NOTE: Poor routing of this input could cause noise or hum.
Allen & Heath 29 XONE:S2 User
USER LINK OPTIONS
CAUTION: The following service instructions are for use by qualified personnel
only.
To reduce the risk of electric shock do not perform any servicing other than
that described in the operating instructions unless you are qualified to do so.
Refer all servicing to qualified service personnel.
Input Channel PCB
Remove jumper links JP1 and JP2 to convert the RIAA stage to line level.
JP1
JP2
Allen & Heath 30 XONE:S2 User
Filter PCB
USER LINK OPTIONS
Remove JP1to disable the Filter On
switch.
Headphone PCB
To change the USB Audio input feed
from the RCA sockets on the rear panel
(default) to the internal left/right mix
buss, move jumper links CN8 and CN9
from pins 2-3 to 1-2.
Allen & Heath 31 XONE:S2 User
REPLACING THE CROSSFADER / FACE PLATE
Replacing the Crossfader
Use a medium size cross-point screwdriver to undo and remove the two outer screws on the
crossfader plate. Do not remove the inner screws. Carefully pull the crossfader assembly away
from the front panel. Unplug the cable from the old crossfader and plug in the new assembly.
Check that the connector is correctly aligned and pushed on. Replace the assembly making sure the
cable faces the left side of the console. Refit the screws and test operation.
Standard Alpha Crossfader Part Number— 003-724
Penny and Giles Crossfader Option Part number— 003-726 JIT
Replacing the Fader Plate
To convert the Xone:S2 from linear faders to rotary or from rotary to linear, undo the four crosspoint screws and carefully pull fader plate away from the front panel. Gently pull the wire harness
of the fader PCB (be very careful not to pull the other end of the harness off the slave PCB).
Replacement is the reversal.
Rotary Fader Plate - Xone:S2—Rotary
Linear Fader Plate - Xone:S2—Linear
Allen & Heath 32 XONE:S2 User
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.