NOTES:
Read the Safety Instructions Sheet and Safety Warning information printed on mixer9s rear
and base panels BEFORE operating.
For full details, please refer to the XONE:PX5 User Guide online at: www.allen-heath.com
Register your XONE:PX5 with Allen & Heath online at: www.allen-heath.com/register
A limited one year manufacturer9s warranty applies to this product, the conditions of which
can be found in the XONE:PX5 User Guide, and online at: www.allen-heath.com/legal
By using software designed for use for and with this Allen & Heath product you agree to be
bound by the terms of the relevant End User Licence Agreement (EULA), a copy of which
can be found at: www.allen-heath.com/legal
Copyright © 2016 Allen & Heath Limited. All rights reserved.
Allen & Heath Limited, Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
www.allen-heath.com
QUICK START GUIDE
Publication AP10316_2
Thank you for purchasing the Allen & Heath XONE:PX5, 4+1 Analogue DJ mixer, featuring:
- Four stereo, 3-source, PHONO/LINE/USB input channels plus dedicated MIC/AUX/USB RETURN.
- Internal XONE:FX engine for performance effects with FX SEND/RETURN, INSERT and DUAL mode.
- 20 channel, 24Bit/96kHz, Hi-Speed USB internal soundcard with MIDI Control and X:Link connectivity.
- Classic XONE:VCF Voltage Controlled Filter and 60mm linear VCA channel faders.
- Dedicated connections for external FX SEND/RETURN, MASTER INSERT and MIDI SYNC/OUT.
Please take the time to familiarise yourself with all controls.
20 19 18
REAR PANEL OVERVIEW cont. FRONT PANEL OVERVIEW
17
1
2
3
4
5
6
7
11 10 9 8 12
Input Select Switches
1
Switch Channel A between XLR MIC, CH5 USB RTN soundcard input, or auxiliary CH A LINE
sources. Switch CH 1 - 4 inputs between RCA PHONO, CH 1 - 4 USB RTN soundcard inputs,
or alternative RCA LINE sources.
Channel GAIN Controls
2
Adjusts the Channel input sensitivity to compensate for different audio signal source levels
-∞/+10dB.
Channel Equalizer
3
Each main Channel is equipped with a powerful 3 band isolator EQ, providing a controlled +6dB
boost when fully clockwise and full attenuation (8kill9) on each band when fully anti-clockwise.
X-FADE Assign Switch, CH 1 - 4
4
Used to assign the Channel to either the X (Left), or Y (Right) side of the cross-fader, or direct to
LR MIX bus (OFF).
Channel FILTER Select Switches, CH A / CH 1 - 4 / EXT RTN
5
Press to route post-GAIN / post-EQ / post-Fade level Channel audio to the FILTER.
17
16
14
15
14
13
16
15
13 12 11 10 9 14
MASTER INSERT
9
Provides INSERT points for LR MIX output to connect hardware dynamics processors such as a
limiter, compressor, or graphic equaliser.
Or, connect FX hardware in-line with MIX output for external MASTER INSERT FX.
BOOTH Outputs
10
Balanced LINE level stereo output feed to DJ9s local monitor.
X:LINK
11
Connect XONE:K Series Controllers to the XONE:PX5 for remote software MIDI Control and
saving use of computer USB ports.
USB Soundcard
12
20 Channel (5 Stereo IN / 5 Stereo OUT), 24Bit/96kHz, Hi-Speed USB internal soundcard.
Mac OS X CoreAudio/CoreMIDI class compliant.
MIDI SYNC / OUT
13
MIDI Clock and MIDI Tx (transmit) signal output for syncing to external MIDI hardware.
AC Mains Input
14
Connect (supplied) cable with moulded plug compatible to local AC mains supply.
Turn AC supply to the mixer ON / OFF.
K-Slot
15
Security slot to connect locking, Kensington® type, anti-theft cable.
RECORD Outputs
16
Unbalanced RCA. Pre-MASTER level, LR MIX output for connection to external hardware recording devices.
USB 9-10 Send Select Switch
17
Set CH5 USB SND to MST or FX to route LR MIX or FX SEND output via USB. For pre-MASTER
level stereo LR MIX recording to computer, or using FX SEND for software effects plug-ins.
For full details, please refer to the XONE:PX5 User Guide online at: www.allen-heath.com
XONE:FX CONTROL SECTION
SETUP EXAMPLES
FX ASSIGN Switch
1
Rotary selector used to assign internal XONE:FX engine routing as
Channel INSERT, Master INSERT, or SEND / RETURN to LR MIX.
FX SEND PRE / POST Switch
2
Used to configure Internal and External FX SEND from Channels
to pre-Fade, or post-Fade levels..
FX X-FADE Assign Switch
3
Used to assign the XONE:FX to X (left), Y (right) position of the crossfader to enable fading between Wet (effected) or Dry (un-effected)
signal, or OFF (centre).
TFT Screen
4
Displays XONE:FX settings, BPM and other MENU options.
FX SELECT Encoder
5
Scroll between XONE:FX and CONFIG options. Push ONCE to enter
FX MENU, Scroll then PRESS to select FX. Push + HOLD for CONFIG.
BEAT Adjust / Tempo BEND / MIDI Transport
6
BEAT - Adjust beat fraction of any time based effect (Delay, Reverb,
Flanger, etc).
BEND - Press to speed up or slow down BPM Clock, or to lock-in sync.
MIDI - Transport sends START, STOP & CONTINUE messages for USB
and MIDI SYNC / OUT.
MODE Button Switch
7
3 layer functionality. Push to increment; BEAT / BEND / MIDI CLOCK.
TAP Tempo Button
8
Guide the tempo of the BPM clock manually by tapping to the beat.
INTERVAL / DECAY / FOCUS Controls
9
Adjust preset parameters for currently selected XONE:FX.
INTERVAL - Illuminates WHITE when active.
DECAY - Illuminates RED when active.
FOCUS - Illuminates RED or BLUE when active and GREEN in central
position.
XONE:FX LEVEL Control
10
Adjust XONE:FX output level to LR MIX in SEND mode,
Blend level between Channel audio and selected XONE:FX in INSERT
mode.
Illuminates CYAN for SND/RTN and RED for INSERT.
XONE:FX ON / OFF Switch
11
Turns the FX channel on/off. Illuminates GREEN when active.
XONE:FX CUE Switch
12
Press to listen to the FX channel pre-fade signal level from PHONES
outputs and to view its level on the main MIX meters. Illuminates RED when active.
For full details, please refer to the XONE:PX5 User Guide online at: www.allen-heath.com
2
4
7 8
10
11
6
1
3
5
9
12
STANDARD MIX : ANALOGUE + DIGITAL + MC
VINYL & MEDIA PLAYER (RCA) / LAPTOP (USB) / MIC (XLR)
KEY:
RCA (PHONO)
USB (TYPE A-B)
EXT FX (¼= JACK)
X:LINK (CAT-5)
INSERT (TRS)
MIC (XLR)
ADVANCED MIX : ANALOGUE + DIGITAL + HARDWARE FX + CONTROL
VINYL & MEDIA PLAYER (RCA) / LAPTOP (USB) / EXT FX (INSERT & SND-RTN) / X:LINK
REAR PANEL OVERVIEW
6
6 5 4 3 1 2
7
8
9
8 7
External Effects Connectors, EXT RTN / LINE/Hi-Z / FX SEND
1
Connect external effects device outputs to EXT RTN inputs and use EXT RTN control to adjust
FX signal level sent to main LR MIX or VCF FILTER.
Set input impedance for external FX between LN, or Hi-Z suitable for guitar FX pedals or legacy
hardware. Connect your external FX device inputs to FX SEND and use FX SEND controls to
send Channel audio to the FX unit.
USB LINE / PHONO Select Switches, CH 1 - 4
2
Set CH1 - 4 USB SND to LN or PH. For LINE or RIAA signal level input to internal soundcard.
For recording Channel input audio via USB, or CD / Vinyl timecode control.
LINE Inputs, CH 1 - 4
3
Connect stereo LINE level media players to the LINE input. Do not connect turntables requiring
RIAA equalisation. You can also connect to LINE level jack sources using RCA to jack adapter/
cable.
Chassis Earth Terminals
4
2 x Screw terminals are provided for connecting the earth straps from turntables to prevent
ground hum.
PHONO Inputs, CH 1 - 4
5
Connect turntables with magnetic cartridges requiring RIAA equalisation to PHONO inputs.
For non-RIAA turntables plug into the LINE input instead.
MIC Input, CH A
6
Use a good quality low impedance dynamic mic, wired; Pin1=Ground, Pin2=Hot(+), Pin3=Cold(-)
Do NOT use high impedance or unbalanced microphones, or condenser mics requiring phantom
power.
LINE Inputs, CH A
7
Connect auxiliary or balanced LINE level music sources to the CH A LINE input.
MASTER Outputs
8
Master1. Main stereo LR MIX outputs that feed the club PA system, or balanced active speakers.
Master2. Alternative stereo MIX output to feed consumer amplifier or unbalanced active speakers.
10
11
12
13
14
15
16
17
18
19
20
Channel CUE Switches, CH A / CH 1 - 4 / XONE:FX
Press to listen to the Channel pre-Fade audio levels from PHONES and BOOTH DJ monitor
outputs and to view its level on the main (MIX) Meters.
Headphone Section
Stereo 1/4= TRS Jack and 3.5mm mini-Jack sockets with level control, CUE / MIX control and
SPLIT CUE ON / OFF.
Channel ON/OFF Switch, CH A
Turns the Channel ON or OFF, allowing audio to be routed to the main LR MIX. Useful if an
un-switched microphone is used to easily switch in and out of a mix.
This does not affect CH A signal output to CUE.
Channel Faders, CH 1 - 4
60mm linear VCA Channel Faders adjust the Channel audio levels from fully off to fully on.
X-FADER
Fade between audio from CH 1 - 4 assigned to the X (Left), or Y (Right) side of the cross-fader.
Channel Meters, CH 1 - 4
Channel audio input is metered at post-EQ
on input levels before routing audio to the LR MIX.
FILTER Section
Classic analogue XONE Voltage Controlled Filter section: RESONANCE (Mild to Wild) control,
HPF / BPF / LPF select switches, FREQ (Frequency Sweep) control and FILTER ON / OFF switch.
FADER Curve Switches, CH1 - 4 / X-FADE
Sets the response for Channel 1 - 4 up-faders and VCA cross-fader.
Choose settings to best suit your performance style.
XONE:FX Control Section
Please refer to the XONE:FX Control Section overleaf for more information.
EXT RTN Level Control
Adjusts the level of audio input from effects hardware connected via FX SEND/ EXT RTN and
routed to the XONE:VCF FILTER or LR MIX outputs.
MIX / MONITOR Meters
The main meters follow the selected monitor source. In SPLIT cue mode, Left (L) MIX meter
displays cued Channel audio levels and Right (R) MIX meter displays MIX output level.
XONE:FX ASSIGN Section Controls
Pre/Post-Fade FX SEND, Channel FX ASSIGN, and FX: X-FADE Assign switches.
Please refer to the XONE:FX Section Overview for more information.
MASTER / BOOTH Level Controls
MASTER adjusts level for the LR MIX feeding MASTER 1 and MASTER 2 outputs.
MASTER Level adjustment does not affect the BOOTH output or the meter reading.
BOOTH adjusts the level output to DJ9s local monitor output. This does not affect PHONES level.
FX SEND Controls, CH A / CH 1 - 4
Controls the amount of Channel audio sent to the XONE:FX bus and/or external effects
hardware connected via rear panel EXT RTN inputs.
Channel FX Mode Select Switches, CH A / CH 1 - 4
Selects option for Channel FX SEND routing to INT, EXT, or DUAL.
For SEND to internal XONE:FX engine, external effects hardware connected via EXT RTN inputs,
or to both for simultaneous use with internal and external effects.
and pre-Fade level, to display affect of EQ adjustment
Loading...