Page 1
Installation Instruction
ClearSight RightSightt PHOTOSWITCH
R
Photoelectric Sensors
Sensing Mode Clear object
Sensing Distance 1.2m
Field of View
Transmitting LED Visible Red 660nm
Optical
Sensitivity Adjustment Yes , sing l e tu rn
Supply Voltage 10.8--30V DC (DC models), 21.6--264V AC/DC
Current Consumption 35mA maximum
Protection False pulse on power up, reverse polarity, output
Output Type Dual NPN and PNP (DC models),
Electrical
Output Load Voltage/Current 100mA @ 30V DC (DC models), 100mA @ 264V
Output Energized Light/Dark operate by catalog number
Output Response Time 0.5ms (DC models), 1ms (AC/DC models)
Housing Material Mindel
Lens Material Acrylic
Indicators Yellow: Output, Green: Power, Orange: Margin/SCP
Mechanical
Operating Temperature
Operating Environment NEMA 3R, 4X, 6P; IP67 1200psi washdown
Vibration 10--55Hz, 1mm amplitude, Meets or exceeds IEC
Shock 30G with 1ms pulse duration, Meets or exceeds IEC
Environmental
Relative Humidity Up to 95%
Approvals UL, CSA, CE marked for all applicable directives
Supplied 92--90 Reflector
Optional 889D--F4AC--2 cordset (DC models),
Accessories
1.5_
(AC/DC models)
short-circuit protection, overvoltage
MOSFET (AC/DC models)
AC/DC (AC/DC models)
-- 2 5 _Cto+70_C(--13_F to +158_F)
947--5--2
947--5--2
18mm locknut
889R--F4AEA--2 cordset (AC/DC models)
60--2649 Tilt/Swivel Mounting Bracket
60--2657 Mounting bracket, metal
LED Function Tables
DC Models
Label Color State Status
OFF Output de energized
Output Yel low
Margin Orange
Power Green
AC/DC Models
Label Color State Status
Output Yel low
Margin Orange
Power Green
Short-Circuit Protection Feature (SCP)
RightSight photoelectric sensors provide short-circuit protection (SCP) on the
output leads. This feature is intended to protect the sensor from damage in
the event that the output load is shorted to ground. If this condition does
occur, the SCP will activate and the orange and yellow LEDs will flash (for
AC/DC models only the orange indicator will flash) until the source of the short
isremoved(powermustberesetforAC/DC models). The SCP limits are set
to 100mA over the entire voltage range.
ON Output energized
Flashing Output SCP active
OFF Margin < 2.5
ON Margin >2.5
Flashing Output SCP active
OFF Sensor not powered, output active, SCP active
ON Sensor powered
OFF Output de energized or SCP active
ON Output energized
OFF Margin < 2.5
ON Margin >2.5
Flashing Output SCP active (short circuit)
OFF Sensor not powered
ON Sensor powered or SCP active
1
Page 2
Typical Response Curves
8
Margin Curve Beam Pattern
10
Margin
15
10
5
0
mm
Width,
-- 5
-- 1 0
1
0 1500
500
(19.6)
1000
(39.3)
Sensing Range—mm (in)
Wiring Diagrams
10.8--30V DC Sensors
Models with Dual NPN and PNP Outputs
Note: All wire colors on quick-disconnect models shown refer to Allen-Bradley cordsets.
Brown
White
Black
Blue
+
Load
Load
--
1
Brown
2
White
4
Black
3
Blue
Cable Quick-Disconnect
Load
Load
(59.0)
+
--
1324
DC Micro
2000
(78.7)
-- 1 5
0 1500
500
(19.6)
1000
(39.3)
Sensing Range—mm (in)
21.6--264V AC/DC Sensors
ACWiringfor42EF--___C__--__Models
Cable
Blue
Black
Brown
L1
Load
L2
2
3
1
Quick-Disconnect
DCWiringfor42EF--___C__--__Models
1
3
2
Quick-Disconnect
Cable
Brown
Black
Blue
+
Load
--
Red/White
Red
Red/Black
Red/Black
Red
Red/White
Load
(59.0)
Load
20
(7
L1
3
2
4
1
L2
+
3
2
4
1
--
2
Page 3
Sensor Dimensions—mm (inches)
26.5
20.5
(0.81)
34.5
(1.36)
10
(0.40)
M18 X 1.0 Thread
16.5
(0.65)
9.6
(0.38)
32.7
(1.29)
4
(0.16)
19
(0.75)
2m (6.56ft)
Cable
27
(1.06)
69
(2.72)
49.7
(1.96)
3.6 (0.145) Diameter
Clearance for #6-- 32
Screw (2 Places)
Sensitivity Adjustment
18mm mounting nut
Indicators
10_Adjustment in
Each Direction
57.15
(2.25)
28.6
(1.125)
AC/DC
(1.04)
Accessories
Right Angle Bracket #60--2657 Swivel/Tilt Bracket #60 --2649
DC
(0.40)
34.5
(1.36)
20.5
(0.81)
10
10
(0.40)
M18 X 1.0 Thread
16.5
(0.65)
Notes
1. Damage may occur to sensor housing if
2. Optional mounting kit (60--2716) comes
32.7
(1.29)
9.6
(0.38)
(0.16)
19
(0.75)
torque above 20in-lb is applied to the
18mm locknut.
with two 75012--025-- 01, one
75012--097--01 locknut, internal tooth
star washer, and screws/nuts for
through-hole mounting.
27
(1.06)
46.7
(1.84)
27.5
4
(1.08)
3.6 (0.145) Diameter
Clearance for #6--32
Screw (2 Places)
7.95
(0.31)
50.08
(2.0)
3
Page 4
Configuring the Sensor
All ClearSight RightSight models contain a single turn adjustment knob on the
top cover. This knob controls the sensitivity of the sensor to the light being
reflected back toward it by the reflector. The factory default setting is at
maximum sensitivity
1. Visually align the sensor on the reflector until the yellow output LED turns
ON (light operate models) or turns OFF (dark operate models). Also verify
that the orange margin LED turns ON.
between both positions. The visible red beam of the sensor will be visisble
on the reflector and can be used as an alignment aid.
3. Break the beam with the object to be detected and check if the output
indicator turns ON (dark operate models). If this does not occur, turn down
the sensitivity adjustment until it does. Restore the light beam by r emoving
the object and check if the indicator turns OFF again and that the orange
margin LED comes ON. If this does not occur, increase the size of the
reflector or decrease the distance between the reflector and the sensor.
2. To be certain that the beam is centered, it is required to sweep the sensor
in both the horizontal and vertical planes and determine at what position
the output indicator goes ON and then goes OFF. Set the sensor midway
Accessories—Description Catalog Number
Mounting Kit 60- 2716
Clamp Style Bracket 871A- BP18
Flush Mount Adaptor 60- 2590
Field Mount Terminal Chamber—4-pin DC Micro 871A- TS4- DM
Cordset—2m (6.5 ft), 4-pin DC Micro 889D- F4AC- 2
Cordset—2m (6.5 ft), 4-pin AC Micro 889R- F4AEA-2
Reflector—1.25 inch diameter 92- 47
Reflector—3 inch diameter 92- 39
In some applications it may be necessary to slightly angle the sensor and
reflector into the target to minimize false triggering of the sensor output.
Depending on the type of clear object to be sensed, a sensor with coaxial
optics like the ClearSight 10,000 or ClearSight 9000 models may be required.
PHOTOSWITCHRis a registered trademark of Rockwell Automation.
Visit our web site at www.ab.com.
4
Publication 75039 --096--01(B)
November 2004
Printed in USA
Loading...