Allen-Bradley 2080-SERIALISOL, 2080-LC50-24QWB, 2080-LC50-24AWB, 2080-LC10-12QWB, 2080-LC30-16QWB Owners Manual

...
Page 1
User Manual
Original Instructions
Micro800 Plug-in Modules
Catalog Numbers 2080-IQ4, 2080-IQ4OB4, 2080-IQ4OV4, 2080-OB4, 2080-OV4, 2080-OW4I, 2080-IF2, 2080-IF4, 2080-OF2, 2080-TC2, 2080-RTD2, 2080-MEMBAK-RTC, 2080-MEMBAK-RTC2, 2080-TRIMPOT6, 2080-SERIALISOL, 2080-DNET20, 2080­MOT-HSC
Page 2

Important User Information

Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT Identifies information that is critical for successful application and understanding of the product.
Labels may also be on or inside the equipment to provide specific precautions.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
Page 3

Preface

Read this preface to familiarize yourself with the rest of the manual. It provides information concerning:
who should use this manual
the purpose of this manual
related documentation
supporting information for Micro800™ plug-in modules and accessories

Who Should Use this Manual

Purpose of this Manual

Conformal Coated Catalogs

Use this manual if you are responsible for designing, installing, programming, or troubleshooting control systems that use Micro800 controllers.
You should have a basic understanding of electrical circuitry and familiarity with relay logic. If you do not, obtain the proper training before using this product.
This manual is a reference guide for Micro800 controllers, plug-in modules and accessories. It describes the procedures you use to install, wire, and troubleshoot your controller. This manual:
explains how to install and wire your plug-ins
gives you an overview of the Micro800 plug-in modules and accessories
Refer to the additional resources for more information on other element of the Micro800 system.
Catalog numbers with the suffix ‘K’ are conformal coated and their specifications are the same as non-conformal coated catalogs.

Additional Resources

These documents contain additional information concerning related Rockwell Automation products.
Resource Description
Micro820 Programmable Controllers Installation Instructions, publication 2080-IN009
Micro830 Programmable Controllers Installation Instructions, publication 2080-IN002
Micro830 Programmable Controllers Installation Instructions, publication 2080-IN003
Micro830 Programmable Controllers Installation Instructions, publication, 2080-IN004
Micro830 Programmable Controllers Installation Instructions, publication 2080-IN005
Micro850 Programmable Controllers Installation Instructions, publication, 2080-IN007
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 iii
Information on mounting and wiring the Micro820™ 20-point controllers.
Information on mounting and wiring the Micro830® 10-point controllers.
Information on mounting and wiring the Micro830 16-point controllers.
Information on mounting and wiring the Micro830 24-point controllers.
Information on mounting and wiring the Micro830 48-point controllers.
Information on mounting and wiring the Micro850® 24-point controllers.
Page 4
Preface
Resource Description
Micro850 Programmable Controllers Installation Instructions, publication 2080-IN008
Micro870 Programmable Controllers Installation Instructions, publication 2080-IN008
Micro820 Programmable Controller User Manual, publication 2080-UM005
Micro830, Micro850, and Micro870 Programmable Controllers User Manual, publication 2080-UM002
Micro800 Programmable Controller External AC Power Supply Installation Instructions, publication 2080-IN001
Micro800 Remote LCD Installation Instructions, publication 2080-IN010
Micro800 RS232/485 Isolated Serial Port Plug-in Module Wiring Diagrams, publication 2080-WD002
Micro800 Non-isolated Unipolar Analog Input Plug-in Module Wiring Diagrams, publication 2080-WD003
Micro800 Non-isolated Unipolar Analog Output Plug-in Module Wiring Diagrams, publication 2080-WD004
Micro800 Non-isolated RTD Plug-in Module Wiring Diagrams, publication 2080-WD005
Micro800 Non-isolated Thermocouple Plug-in Module Wiring Diagrams, publication 2080-WD006
Micro800 Memory Backup and High Accuracy RTC Plug-In Module Wiring Diagrams, publication 2080-WD007
Micro800 6-Channel Trimpot Analog Input Plug-In Module Wiring Diagrams, publication 2080-WD008
Micro800 Digital Relay Output Plug-in Module Wiring Diagrams, publication 2080-WD010
Micro800 Digital Input, Output, and Combination Plug-in Modules Wiring Diagrams, publication 2080-WD011
Micro800 High-speed Counter Plug-in Module Wiring Diagrams, publication 2080-WD012
Micro800 DeviceNet Plug-in Module Wiring Diagrams, publication 2080-WD013
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1
Application Considerations for Solid-State Controls, publication SGI-1.1
National Electrical Code - Published by the National Fire Protection Association of Boston, MA.
Allen-Bradley Industrial Automation Glossary, publication AG-7.1
Information on mounting and wiring the Micro850 48-point controllers.
Information on mounting and wiring the Micro870™ 24-point controllers.
Information on features, installation, wiring and usage of the Micro820 controllers.
Information on features, installation, wiring and usage of your Micro830, Micro850, and Micro870 programmable controllers.
Information on mounting and wiring the optional external power supply.
Information on mounting and wiring the Micro800 Remote LCD module.
Information on mounting and wiring the Micro800 RS232/485 isolated serial port plug-in module.
Information on mounting and wiring the Micro800 non-isolated unipolar analog input plug-in module.
Information on mounting and wiring the Micro800 non-isolated unipolar analog output plug-in module.
Information on mounting and wiring the Micro800 non-isolated RTD plug-in module.
Information on mounting and wiring the Micro800 non-isolated thermocouple plug-in module.
Information on mounting and wiring the Micro800 memory backup and high accuracy RTC plug-in module.
Information on mounting and wiring the Micro800 6-channel trimpot analog input plug-in module.
Information on mounting and wiring the Micro800 digital relay output plug-in module.
Information on mounting and wiring the Micro800 digital input, output, and combination plug-in module.
Specifications and information on wiring the Micro800 high-speed counter plug-in module.
Specifications and information on wiring the Micro800 DeviceNet plug-in module.
Provides general guidelines for installing a Rockwell Automation industrial system.
A description of important differences between solid-state programmable controller products and hard-wired electromechanical devices.
An article on wire sizes and types for grounding electrical equipment.
A glossary of industrial automation terms and abbreviations.
iv Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 5
Preface
You can view or download publications at http://www.rockwellautomation.com/
literature/. To order paper copies of technical documentation, contact your local
Rockwell Automation distributor or sales representative.
You can download the latest version of Connected Components Workbench for your Micro800 at the URL below.
http://ab.rockwellautomation.com/Programmable-Controllers/Connected­Components-Workbench-Software.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 v
Page 6
Preface

Notes:

vi Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 7
Preface

Table of Contents

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Who Should Use this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Purpose of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Conformal Coated Catalogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Chapter 1
Micro800 Plug-in Modules
Install and Wire Your Module
Digital Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
12/24V Digital Plug-ins — 2080-IQ4, 2080-IQ4OB4, 2080-
IQ4OV4, 2080-OB4, 2080-OV4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
AC/DC Relay Output Module — 2080-OW4I. . . . . . . . . . . . . . . . . . . 3
Analog Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Non-isolated Unipolar Analog Input and Output — 2080-IF2,
2080-IF4, 2080-OF2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Specialty Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Non-isolated Thermocouple and RTD — 2080-TC2 and 2080-
RTD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Memory Backup and High Accuracy RTC — 2080-MEMBAK-RTC
and 2080-MEMBAK-RTC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Six-channel Trimpot — 2080-TRIMPOT6 . . . . . . . . . . . . . . . . . . . . . . 4
High Speed Counter — 2080-MOT-HSC . . . . . . . . . . . . . . . . . . . . . . . 4
Communication Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
RS232/RS485 Isolated Serial Port — 2080-SERIALISOL . . . . . . . . . 4
DeviceNet Scanner — 2080-DNET20 . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2
Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Insert Module into Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Wiring Considerations and Applications for 2080-TC2 . . . . . . . . . . . . . 13
Type of CJC Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wire the CJC Thermistor on the 2080-TC2 Module. . . . . . . . . . . . 13
Wiring Considerations and Applications for 2080-RTD2 . . . . . . . . . . . 15
Two-wire and Three-Wire Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Wire the RTD Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Wire the RTD Module and RTD Sensor in the Field . . . . . . . . . . . . 16
Wiring Applications for 2080-MOT-HSC . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3 Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and 2080-RTD2
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 vii
Thermocouple Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Thermocouple Sensor Types and Ranges . . . . . . . . . . . . . . . . . . . . . . . 19
RTD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RTD Sensor Types and Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connected Components Workbench Global Variables
Data Maps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Temperature Conversion – Data to Degree Celsius (°C) . . . . . . . . . 23
Page 8
Table of Contents
Chapter 4 High Speed Counter – 2080­MOT-HSC
DeviceNet Plug-in – 2080­DNET20
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Differences Between Embedded HSC and Plug-in Module. . . . . . . . . . . 26
Counter Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Number of Counters: 1 to 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Up Counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Counter with External Direction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Understanding Rates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
User Defined Function Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
RA_HSCPlugIn. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Use the 2080-MOT-HSC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Chapter 5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Network Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Network Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
DeviceNet Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
User Defined Function Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RA_DNET_MASTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RA_DNET_NODE_STATUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
RA_DNET_LDX_DISCRETE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
RA_DNET_LDX_ANALOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
RA_DNET_LDX_TC_RTD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
RA_PF_DNET_STANDARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
RA_PF_DNET_MULTIDRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
RA_DNET_OVERLOAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
RA_DNET_GENERIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Send Explicit Messages to 2080-DNET20 Plug-in Using Micro800 Pass
Through. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Error Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Use the 2080-DNET20 Plug-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Appendix A
Specifications
viii Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Digital Plug-in Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Analog Plug-in Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Specialty Plug-in Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Communication Plug-in Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Page 9
Appendix B
Chapter 1
Quickstart
Add and Configure Plug-ins in Connected Components Workbench 83
Browse Your 2080-DNET20 Plug-in Using RSLinx. . . . . . . . . . . . . . . . . 85
Browse Using the DeviceNet Network . . . . . . . . . . . . . . . . . . . . . . . . . 86
Browse Using the Micro800 Pass Through . . . . . . . . . . . . . . . . . . . . . 87
Flash Upgrade Your
2080-DNET20 Plug-in Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Quickstart Project for
2080-DNET20 Plug-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Setup and Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Build and Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Execute Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Quickstart Projects for
2080-MOT-HSC Plug-in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Setup and Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Configuration for UDFB 1: RA_HSCPlugIn . . . . . . . . . . . . . . . . . . 99
Build and Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Execute the Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Configuration for UDFB 2: RA_EncoderFDBK . . . . . . . . . . . . . . 101
Build and Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Execute the Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Configuration for HSC UDFB 3: RA_ServoFDBK . . . . . . . . . . . . 104
Build and Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Execute the Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Error Codes
Index
Appendix C
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Error Codes for Micro800 Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Calling Rockwell Automation for Assistance . . . . . . . . . . . . . . . . . . . . . . 110
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 ix
Page 10
Table of Contents
Notes:
x Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 11
Micro800 Plug-in Modules
Chapter
1
Plug-in modules enhance the functionality of a base unit controller. With these modules, you can:
Extend the functionality of embedded I/O without increasing the footprint of your controller.
Improve performance by adding additional processing power or capabilities.
Add additional communication functionality.
Micro800 controllers support the following plug-in modules:
Micro800 Plug-in Modules
Module Type Description
2080-IQ4 Digital 4-point, 12/24V DC Sink/Source input
2080-IQ4OB4 Digital 8-point, Combo, 12/24V DC Sink/Source input
2080-IQ4OV4 Digital 8-point, Combo, 12/24V DC Sink/Source input
2080-OB4 Digital 4-point, 12/24V DC Source output
2080-OV4 Digital 4-point, 12/24V DC Sink output
2080-OW4I Digital 4-point, AC/DC Relay output
2080-IF2 Analog 2-channel, Non-isolated unipolar voltage/current
2080-IF4 Analog 4-channel, Non-isolated unipolar voltage/current
12/24V DC Source output
12/24V DC Sink output
analog input
analog input
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 1
Page 12
Chapter 1 Micro800 Plug-in Modules
Micro800 Plug-in Modules
Module Type Description
2080-OF2 Analog 2-channel, Non-isolated unipolar voltage/current
analog output
2080-TC2 Specialty 2-channel, non-isolated thermocouple module
2080-RTD2 Specialty 2-channel, non-isolated RTD module
2080-MEMBAK-RTC
2080-MEMBAK-RTC2
(1)
Specialty Memory backup and high accuracy RTC, 1 MB
(1)
Specialty Memory backup and high accuracy RTC, 4 MB
2080-TRIMPOT6 Specialty 6-channel trimpot analog input
2080-MOT-HSC Specialty High speed counter
2080-DNET20 Communication 20-node DeviceNet scanner
2080-SERIALISOL Communication RS232/485 isolated serial port
(1) 2080-MEMBAK-RTC and 2080-MEMBAK-RTC2 are not supported on Micro820 controllers.
2080-MEMBAK RTC is not supported on Micro870 controllers.
Number of support for Micro800 plug-ins on the controllers are summarized in the following table.
Plug-in Slots on Micro800 Controllers
Controller Number of Plug-in Slots
Micro810 0
Micro820 2
Micro830 2 (10/16 points)
3 (24 points) 5 (48 points)
Micro850 3 (24 points)
5 (48 points)
Micro870 3
ATTENTION: Removal and Insertion Under Power (RIUP) is not supported on all Micro800 plug-in modules, except on the 2080-MEMBAK-RTC and 2080-MEMBAK-RTC2 modules.
ATTENTION: Micro800 plug-in modules can be installed on any plug-in slot on the controller, except for the 2080-MEMBAK-RTC and 2080-MEMBAK-RTC2 modules which can only be installed on the leftmost plug-in slot.
2 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 13
Micro800 Plug-in Modules Chapter 1

Digital Plug-ins

Analog Plug-ins

12/24V Digital Plug-ins — 2080-IQ4, 2080-IQ4OB4, 2080-IQ4OV4, 2080-OB4, 2080-OV4
These digital plug-in modules provide transistor outputs for switching a variety of 12/24V DC voltages to field loads and for detecting 12/24V signals from field devices.
AC/DC Relay Output Module — 2080-OW4I
The 2080-OW4I is a 4-channel relay output and provides dry contact relay closure outputs for switching a variety of AC and DC voltages to field loads.
The following analog plug-ins are supported by most Micro800 controllers.
Non-isolated Unipolar Analog Input and Output — 2080-IF2, 2080-IF4, 2080-OF2

Specialty Plug-ins

These plug-in modules add extra embedded non-isolated unipolar (0...10V,
0...20 mA) analog I/O and offer 12-bit resolution.
Non-isolated Thermocouple and RTD — 2080-TC2 and 2080-RTD2
These non-isolated plug-in modules help to make temperature control possible when used with PID (Proportional Integral Derivative).
See Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and
2080-RTD2 on page 19 for more information.
Memory Backup and High Accuracy RTC — 2080-MEMBAK-RTC and 2080-MEMBAK-RTC2
These plug-in modules allows you to make a backup copy of the project in your controller, and adds precision real-time clock function without needing to calibrate or update periodically.
They can also be used to clone/update Micro800 application code. The 2080-MEMBAK-RTC2 has larger memory to support clone/update for Micro870 application code. However, these plug-in modules cannot be used as additional Run-Time Program or Data Storage for recipe and datalog.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 3
Page 14
Chapter 1 Micro800 Plug-in Modules
45068
Channels
012
345
Status Indicators
State Description
Solid red (2 s) Startup cycle test in progress.
Flashing red Back up in progress.
Solid red (continuous) Battery low.
Project Backup and Restore
The project can be backed up and restored using Connected Components Workbench software.
Six-channel Trimpot — 2080-TRIMPOT6
This trimpot plug-in offers an affordable method of adding six analog presets for speed, position and temperature control.
High Speed Counter — 2080-MOT-HSC
This plug-in module provides enhanced high speed counter capabilities to the Micro800 controller. It supports the same functionalities of an embedded HSC on the Micro800 controllers but is enhanced to support up to 250 KHz 5V differential line driver for improved noise immunity and provides additional dedicated I/O.
For more information, see High Speed Counter – 2080-MOT-HSC

Communication Plug-ins

RS232/RS485 Isolated Serial Port — 2080-SERIALISOL
The 2080-SERIALISOL plug-in supports CIP Serial (RS-232 only), Modbus RTU (RS232 and RS485), and ASCII (RS232 and RS485
(1)
the embedded Micro800 serial port, this port is electrically isolated, making it ideal for connecting to noisy devices, such as variable frequency and servo drives,
(1) RS-485 support is only available from Connected Components Workbench revision 6.
4 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
on page 25.
) protocols. Unlike
Page 15
Micro800 Plug-in Modules Chapter 1
IMPORTANT
as well as for communications over long cable lengths. Depending on the application and baud rate setting, you can extend this length.
2080-SERIALISOL is suitable for communication over longer cable length of up to 1000 m using RS485, with up to 19200 bps baud rate.
The electrical characteristics of cable used and good wiring practices are very critical in achieving reliable communication performance over longer cable length. A shielded twisted pair RS485 22AWG cable (example: 3106A from Belden) is recommended. Terminate both ends of the cable with 120 ohm resistance.
DeviceNet Scanner — 2080-DNET20
The Micro800 DeviceNet plug-in module serves as a scanner and client for explicit messaging to remote devices including I/O and drives, using a proven and well-accepted fieldbus/network. It also provides better performance than using serial and Ethernet (EtherNet/IP Class 3) communications.
For more information, see the DeviceNet Plug-in – 2080-DNET20
on page 41.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 5
Page 16
Chapter 1 Micro800 Plug-in Modules

Notes:

6 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 17
Chapter
45010
terminal block
mounting screw hole
mounting
screw hole
20 (0.79)
31.5 (1.24)
62 (2.44)
Measurements in millimeters (inches)
45811
Side view Front view
2080-RTD2 shown
45012
Install and Wire Your Module
This chapter provides hardware features, installation, and wiring connection diagrams for all the Micro800 plug-in modules.
2

Hardware Features

The plug-in modules, except for the 2080-MEMBAK-RTC and 2080-MEMBAK-RTC2, can be plugged into any plug-in slots on the Micro800 controllers.

Insert Module into Controller

Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 7
Follow the instructions to insert and secure the plug-in module to the controller.
Page 18
Chapter 2 Install and Wire Your Module
IMPORTANT
Back
A
B
Front
Twelve-pin Female Terminal Block
A1
A2
A3
A4
A5A6B1B2B3B4B5
B6
1. Position the plug-in module with the terminal block facing the front of the controller as shown.
2. Snap the module into the module bay.
3. Using a screwdriver, tighten the 10…12 mm (0.39…0.47 in.) M3 self
tapping screw to torque specifications. See Specifications
Analog I/O performance depends on the application. For better noise immunity, cable length should ideally be less than 3 m because the plug­ins are non-isolated. For longer cable length requirements, use the 2085 expansion I/O modules instead.
on page 61 for torque specifications.

Wiring

The following plug-in modules have 12-pin female terminal blocks:
2080-IQ4,
2080-IQ4OB4, 2080-IQ4OV4
2080-OB4, 2080-OV4, 2080-OW4I
2080-IF2, 2080-IF4
2080-TC2, 2080-RTD2
Pin Designations for 12-Pin Female Terminal Block Modules
Pin 2080-IQ4 2080-IQ4OB4,
2080-IQ4OV4
I-02 I-02 Not used COM3 COM COM CH0+ CH0+
I-03 I-03 Not used O-3 Not used VI-2 CH0- CH0-
COM COM -24V DC Not used Not used CI-2 CJC+ CH0L (Sense)
COM -24V DC -24V DC Not used COM COM Not used Not used
Not used O-02 O-02 Not used Not used VI-3 Not used Not used
Not used O-03 O-03 Not used Not used CI-3 Not used Not used
2080-OB4, 2080-OV4
2080-OW4I 2080-IF2 2080-IF4 2080-TC2 2080-RTD2
1 2 3 4
1 2 3 4
5 6
5 6
8 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
I-00 I-00 Not used COM0 VI-0 VI-0 CH1+ CH1+
I-01 I-01 Not used O-0 CI-0 CI-0 CH1- CH1-
COM COM +24V DC COM1 COM COM CJC- CH1L (Sense)
COM +24V DC +24V DC O-1 VI-1 VI-1 Not used Not used
Not used O-00 O-00 COM2 CI-1 CI-1 Not used Not used
Not used O-01 O-01 O-2 COM COM TH Not used
Page 19
Example Wiring for 2080-IQ4OB4
+24V DC
-24V DC
+24V DC (Sinking)
-24V DC (Sourcing) CR
Sourcing output
DC input
B
A
CR
CR
CR
-24V DC (Sinking)
+24V DC (Sourcing)
+24V DC
-24V DC
+24V DC (Sinking)
-24V DC (Sourcing) CR
Sinking output
DC input
B
A
CR
CR
CR
-24V DC (Sinking)
+24V DC (Sourcing)
1 2 3 4
1 2 3 4
5 6
5 6
Voltage transmitter
Shielded cable
B
A
Current transmitter
Shielded cable
Voltage transmitter
Current transmitter
Shielded cable
Shielded cable
Install and Wire Your Module Chapter 2
Example Wiring for 2080-IQ4OV4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
5 6
5 6
5 6
5 6
Example Wiring for 2080-IF4
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 9
Page 20
Chapter 2 Install and Wire Your Module
Back
Front
B
A
Eight-pin female terminal block
0-
A-
B-
Z-
A+
B+
Z+
0+
DC(+)
DC(-)
CR
CR
0-
A-
B-
Z-
A+
B+
Z+
0+
DC(+)
DC(-)
Sinking Output Wiring
Sourcing Output Wiring
A1A2A3A4B1B2B3
B4
Voltage transmitter
Shielded cable
B
A
Current transmitter
Shielded cable
1 2 3 4
1 2 3 4
The following plug-in modules have eight-pin female terminal blocks:
2080-OF2
2080-SERIALISOL
2080-MOT-HSC
Pin Designations for 8-Pin Female Terminal Block Modules
Pin 2080-OF2 2080-SERIALISOL 2080-MOT-HSC
COM RS485 B+ O-
COM GND A-
COM RS232 RTS B-
COM RS232 CTS Z-
VO-0 RS232 DCD O+
CO-0 RS232 RXD A+
(1) (2)
VO-1 RS232 TXD B+
CO-1 RS485 A- Z+
(1) IMPORTANT: Individually shielded, twisted-pair cable (or the type recommended by the encoder or sensor
manufacturer) should be used for the 2080-MOT-HSC plug-in.
(2) Sinking Output/Sourcing Output wiring for the 2080-MOT-HSC plug-in is shown below.
Example Wiring for 2080-OF2
10 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
1 2 3 4
1 2 3 4
Page 21
Install and Wire Your Module Chapter 2
DTE Device (Micro800 RS232 Isolated Serial Port Plug-in Module)
DCE Device (Modem, and so on)
8-Pin 25-Pin 9-Pin
B3 TXD TXD 2 3
B2 RXD RXD 3 2
A2 GND GND 7 5
A1 B(+) DCD 8 1
B4 A(-) DTR 20 4
B1 DCD DSR 6 6
A4 CTS CTS 5 8
A3 RTS RTS 4 7
Serial Port to Modem Cable Pinout
When connecting Micro800 to a modem using an RS-232 cable, the maximum that the cable length may be extended is 15.24 m (50 ft).
ATTENTION: Do not connect to pins A1 and B4 for RS-232 connections. This connection will cause damage to the RS-232/485 communication port.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 11
Page 22
Chapter 2 Install and Wire Your Module
IMPORTANT
Color Chips (dots)
Red Dot
Black Dot
Blue Dot
White Dot
10-position Plug
5-position Plug
D D D D D
Linear Plug
10-position
Drop Line or
DeviceNet
Trunk Cable
Red
White Bare
Blue
Black
DeviceNet Port Pinout
V+ (RED)
CANH (WHITE)
SHIELD
CANL (BLUE)
V- (BLACK)
20474
Esc
Sel
Micro800 controller
CompactBlock LDX
COMM power supply
Component on DeviceNet network
PowerFlex Drive 523 via 25-COMM-D
COMM power supply
1 KwikLink Lite IP20 flat media 2 Trunk line connector 3 Drop line connector 4 Terminating resistor 5 5-pin open style connector 6 Power tap with terminating resistor
46220
2080-DNET20 – 6-pin Female Terminal Block
2080-DNET20: Sample network wiring using KwikLink™ Lite Flat media
Individually shielded, twisted-pair cable (or the type recommended by the encoder or sensor manufacturer) should be used for the 2080-MOT-HSC plug-in.
12 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 23
Install and Wire Your Module Chapter 2
IMPORTANT
6.5 max
50 ± 2
0.25
2.41 max
5mm
5mm
B3
A3
1. Connect the thermocouples to
channel 0 and 1, respectively. Then, connect and screw the thermistor to terminals A3 and B3.
2. Once fitted, bend the black bead
of the thermistor such that it makes contact with the A2 screw securely.
A1 A2 A3 A4 A5 A6
B1 B2 B3 B4 B5 B6
CJC- (Black)
CJC+ (Red)
TH
Thermistor

Wiring Considerations and Applications for 2080-TC2

ATTENTION: The module currently ships with the CJC thermistor fixed to
the module. Do not remove or unscrew the CJC thermistor. The following sections apply to the previous version of the module.
Type of CJC Sensor
The CJC sensor is a non-polarized, passive negative temperature co-efficient thermistor (EPCOS B57869S0502F140). It is readily available in the market with most third party suppliers/vendors.
CJC Channel Error
The CJC channel on 2080-TC2 has a worst-case error of ±1.2 °C @ 25 °C. This error does not include the manufacturer-specified sensor error ±0.2 °C @ 25 °C.
Wire the CJC Thermistor on the 2080-TC2 Module
The position for the thermistor, as illustrated, helps to compensate for thermoelectric voltages developed at screw junction equally for thermocouples connected to channels 0 and 1. If the bead is not in proper contact with the screw,
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 13
there will be deviation in readings due to inadequate isothermal compensation.
Page 24
Chapter 2 Install and Wire Your Module
Measuring point insulated (ungrounded)
Measuring point not insulated (grounded)
Thermocouple Measuring point Thermocouple Measuring point
Sheath Sheath
2080-TC2
1 2 3 4 5 6
1 2 3 4 5 6
Red
Blue
Green
Red
Blue
Process temperature measurement
Shielded/sheathed thermocouple sensor
45790
+
-
Cable tray/conduit
Tip designs of thermocouple sensors
Wire the Thermocouple Module and Thermocouple Sensor in the Field
Connect the thermocouple sensors directly to the module terminals.
Direct sensor wiring
ATTENTION: Direct wiring is the preferred method of wiring for
thermocouples.
14 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 25
Install and Wire Your Module Chapter 2
3 Wire
2 Wire
45772
white
red
Ch0+
Ch0-
Ch0L
white
red
red
green
black
black
white
red
red
Ch1+
Ch1-
Ch1L
Ch0-
Ch0L
Ch0+
Ch0-
Ch0L
Ch0+
2-wire sensor connection
3-wire single sensor connection
3-wire dual sensor connection
45778
NOTE: This illustration provides for channel 0 only for 2- and 3­wire single sensor connections. The wire colors illustrate a particular type of RTD sensor available in market.

Wiring Considerations and Applications for 2080-RTD2

Two-wire and Three-Wire Wiring
1 23
12 3
Wire the RTD Sensors
In an RTD sensor, the sensing element is always connected between two wires of different colors. Wires of the same color are shorted and form the compensation leads. Measuring resistance between these wires confirms the position of sensing element and compensation elements. Compensation elements will always show 0ohms.
Wire the Sensors
For better accuracy in noisy industrial environments, 3- or 4-wire RTD sensors are mostly used. While using these sensors, the resistance added by lead lengths is compensated by an additional third wire in case of 3-wire RTD and two additional wires, in bridge configuration, in case of 4-wire RTD. For 2-wire RTD sensor in this module, this lead compensation is provided by using an external 50 mm 22 AWG shorting wire between terminals A2, A3 and B2, B3 for channel 0 and 1, respectively. Shielded twisted pair cables are to be utilized for remote use of these sensors with cable shield grounded at controller end.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 15
Page 26
Chapter 2 Install and Wire Your Module
IMPORTANT
Process temperature Measurement
Shielded twisted wire cable
Field screw junction box
3-wire RTD
Oil filled thermowell
45779
3-wire RTD shown
Cable tray/conduit
Wire the RTD Module and RTD Sensor in the Field
2080-RTD2
Red
Black
Blue
2
1
3
The RTD sensing element should always be connected between terminals B1(+) and B2(-) for channel 1, and A1(+) and A2(-) for channel 0 in the module. Terminals B3 and A3 should always be shorted to B2 and A2, respectively, to complete the constant current loop. Mismatch in wiring can cause erroneous, over, or underrange readings.
Green
Black
Blue
B
1 2 3 4 5 6
1 2 3 4 5 6
A
Red
Cabling used with the 2080-TC2/RTD2 modules have to be shielded twisted cores with the shield wire shorted to chassis ground at controller end. It is advisable to use 22 AWG wires to connect the sensors to the module. Use sensors dipped in oil-filled thermowells for stable and uniform readings. Recommended cable type: Alpha wire P/N 5471C.
Performance is dependent on the application. For better noise immunity, cable length should ideally be less than 3 m because the plug-ins are non-isolated. For longer cable length requirements, use the 2085 expansion I/O modules instead.
16 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 27
Install and Wire Your Module Chapter 2
Micro830/Micro850 QBB (24 pts)
PTO
I/O Connector
49 = 24V_PULS+ 12 = PLUS­14 = SIGN­25 = 24V_SIGN+
I/O Connector
29 = AM+ 30 = AM­31 = BM+ 32 = BM-
49
12 14
25
FEEDBACK
A+ A-
B+
B-
O-00
-CM0
-CM1
O-03
29
30
31
32

Wiring Applications for 2080-MOT-HSC

The following diagrams show wiring applications for the 2080-MOT-HSC plug-in with Kinetix® Servo drives.
Kinetix 3 in feedback configuration to 2080-MOT-HSC
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 17
Page 28
Chapter 2 Install and Wire Your Module
Micro830/Micro850 QBB (24 pts)
PTO
I/O Connector
49 = 24V_PULS+ 12 = PLUS­14 = SIGN-
25 = 24V_SIGN+
I/O Connector
29 = AM+ 30 = AM­31 = BM+ 32 = BM-
1
2
3 4
FEEDBACK
A+ A-
B+ B-
O-00
-CM0
-CM1
O-03
7
8
9
10
Kinetix 300 in feedback configuration to 2080-MOT-HSC
18 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 29
Chapter
3
Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and 2080-RTD2
The Thermocouple (2080-TC2) and RTD (2080-RTD2) plug-in modules allow for temperature measure and control when used with PID.
This plug-in can be used in any slot of your Micro800 controller. Removal and Insertion Under Power (RIUP) is not supported.

Thermocouple Module

The 2080-TC2 two-channel plug-in module supports thermocouple measurement. It digitally converts and transmits temperature data from any combination of up to eight types of thermocouple sensors. Each input channel is individually configurable through the Connected Components Workbench software for a specific sensor, filter frequency.
Thermocouple Sensor Types and Ranges
The module supports B, E, J, K, N, R, S, T types of thermocouple sensors. The module channels are referred to as Channel 0, Channel 1, and CJC, respectively. The cold junction compensation is provided by an external NTC thermistor, which comes with the module. The thermistor has to be fitted to the screw terminals A3 and B3 of the module. This CJC is common to channel 0 and 1 thermocouple sensors and provides open-circuit, overrange and underrange detection and indication.
Overrange and Underrange Conditions
If the channel temperature input is below the minimum value of its normal temperature range for the represented sensor, the module reports an underrange error through the Connected Components Workbench global variables. If the channel reads above the maximum value of its normal temperature range for the represented sensor, an over-range error is flagged.
The table below defines thermocouple types and their associated full-scale temperature ranges.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 19
Page 30
Chapter 3 Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and 2080-RTD2
Thermocouple Sensor Types and Temperature Ranges
Thermocouple Ty pe
B 40 (104) 1820
E -270 (-454) 1000
J -210 (-346) 1200
K -270 (-454) 1370
N -270 (-454) 1300
R -50 (-58) 1760
S -50 (-58) 1760
T -270 (-454) 400
Temperature Range
° C (°F)
Min Max ±1.0 °C ±3.0 °C
(3308)
(1832)
(2192)
(2498)
(2372)
(3200)
(3200)
(752)
90…1700 (194…3092)
-200…930 (-328…1706)
-130…1100 (-202…2012)
-200…1300 (-328…2372)
-200…1200 (-328…2192)
40…1640 (104…2984)
40…1640 (104…2984)
-220…340 (-364…644)
Accuracy
° C (°F)
< 90 (194) > 1700 (3092)
< -200 (-328) > 930 (1706)
< -130 (-202) > 1100 (2012)
< -200 (-328) > 1300 (2372)
< -200 (-328) > 1200 (2192)
< 40 (104) > 1640 (2984)
< 40 (104) > 1640 (2984)
< -220 (-364) > 340 (644)
ADC Update Rate in Hz (Accuracy °C)
4.17, 6.25, 10, 16.7 (±1.0)
19.6, 33, 50, 62,
123, 242, 470 (±3.0)
To configure Thermocouple type and update rate in Connected Components Workbench software, refer to the section Quickstart
on page 83.

RTD Module

The 2080-RTD2 module supports RTD measurement applications that support up to two channels. The module digitally converts analog data and transmits the converted data in its image table.
The module supports connections from any combination of up to eleven types of RTD sensors. Each channel is individually configurable through the Connected Components Workbench software. When configured for RTD inputs, the module can convert the RTD readings into temperature data. Refer to
Conversion – Data to Degree Celsius (°C) on page 23
, for converting temperature
Tem p e r a tu r e
data to actual temperature degree.
RTD Sensor Types and Ranges
Each channel provides open-circuit (all wires), short-circuit (excitation and return wires only), and over- and under-range detection and indication. The 2080-RTD2 module supports 11 types of RTD sensors:
Pt100 385 PT1000 385 PT500 392 Ni120 672
PT200 385 PT100 392 PT1000 392 NiFe604 518
PT500 385 PT200 392 Cu10 427
20 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 31
Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and 2080-RTD2 Chapter 3
It supports two- and three-wire type of RTD sensor wiring.
RTD Compatibility
An RTD consists of a temperature-sensing element connected by two, three, or four wires that provide resistance input to the module. The following table lists the RTD types that you can use with the module, including their temperature range, accuracy, and ADC update rate.
Overrange and Underrange Conditions
If the channel temperature input is below the minimum value of its normal temperature range for the represented sensor, the module reports an underrange error through the Connected Components Workbench global variables. If the channel temperature input is above the maximum value of its normal temperature range for the represented sensor, an over-range error is flagged.
RTD Sensor Types and Temperature Ranges
RTD Type Temperature
PT100 385 -200
PT200 385 -200
PT500 385 -200
PT1000 385 -200
PT100 392 -200
PT200 392 -200
PT500 392 -200
PT1000 392 -50
Cu10 427
Ni120 672 -80
NiFe604 518 -200
(1)
Range ° C (°F)
Min Max ±1.0 °C ±3.0 °C
(-328)
(-328)
(-328)
(-328)
(-328)
(-328)
(-328)
(-58)
-100 (-148)
(-112)
(-328)
660 (1220)
630 (1166)
630 (1166)
630 (1166)
660 (1220)
630 (1166)
630 (1166)
500 (932)
260 (500)
260 (500)
200 (392)
Accuracy ° C (°F) ADC Update
-150…590 (-238…1094)
-150…570 (-238…1058)
-150…580 (-238…1076)
-150…570 (-238…1058)
-150…590 (-238…1094)
-150…570 (-238…1058)
-150…580 (-238…1076)
-20…450 (-4…842)
-50…220 (-58…428)
-170…170 (-274…338)
< -150 (-238) > 590 (1094)
< -150 (-238) > 570 (1058)
< -150 (-238) > 580 (1076)
< -150 (-238) > 570 (1058)
< -150 (-238) > 590 (1094)
< -150 (-238) > 570 (1058)
< -150 (-238) > 580 (1076)
< - 20 (-4) > 450 (842)
< -70 (-94) > 220 (428)
< -50 (-58) > 220 (428)
< -170 (-274) > 170 (338)
Rate in Hz (Accuracy °C)
3-wire others
4.17, 6.25, 10, 16.7,19.6, 33, 50 (±1.0)
62, 123, 242, 470 (±3.0)
2- and 3-wire Cu10
4.17, 6.25, 10, 16.7 (>±1.0 < ±3.0)
19.6, 33, 50, 62, 123, 242, 470 (> ±3.0)
2-wire others
4.17, 6.25, 10, 16.7 (±1.0)
19.6, 33, 50, 62, 123, 242,
470 (±3.0)
(1)
(1) For Cu10 427, accuracy range is within >±1.0 < ±3.0 for -70…220 °C (-94…428 °F). Above this temperature
range, it is > ±3.0 °C as shown in the table.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 21
Page 32
Chapter 3 Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and 2080-RTD2
Connected Components Workbench Global
The following bit/words describe the information read from the Thermocouple and RTD plug-in modules in the Connected Components Workbench Global Vari ab le s.
Variables Data Maps
Mapping Table
Word Offset Bit
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
00 (example: _IO_P1_AI_00) Channel 0 Temperature Data
01 (example: _IO_P1_AI_01) Channel 1 Temperature Data
02 (example: _IO_P1_AI_02) Channel 0 Information
UKT UKR Reserved Reserved OR UR OC DI CC Reserved
03 (example: _IO_P1_AI_03) Channel 1 Information
UKT UKR Reserved Reserved OR UR OC DI CC Reserved
04 (example: _IO_P1_AI_04) System Information
Reserved SOR SUR COC CE Reserved
Bit Definitions
Bit Name Description
Channel Temperature Data The temperature count mapped from temperature Celsius degree
UKT (Unknown Type) Bit set to report an unknown sensor type error in configuration.
UKR (Unknown Rate) Bit set to report an unknown update rate error in configuration.
OR (Overrange) Bit set to indicate overrange on channel input. The Channel
UR (Underrange) Bit set to indicate the channel input underrange happens. The
OC (Open Circuit) Bit set to indicate open-circuit on the channel input sensor.
DI (Data Illegal) The data in the channel data field is illegal and cannot be used
CC (Code Calibrated) Bit set indicates temperature data is calibrated by the system
SOR (System Overrange) Bit set to indicate system overrange error with environment
SUR (System Underrange) Bit set to indicate system underrange error with environment
COC (CJC open-circuit) Bit set to indicate CJC sensor not connected for thermocouple
CE (Calibration Error) Bit set indicates that the module is not accurate. This bit is set to
with one decimal. Please check the section, Temperature
Conversion – Data to Degree Celsius (°C) on page 23, for the
mapping formula.
Temperature Data shows maximum temperature count for individual type of sensor used and the value does not change until overrange error is clear.
Channel Temperature Data will show minimum temperature count for individual type of sensor used and the value does not change until underrange error is clear.
by user. This bit is set when temperature data is not ready for use.
calibration coefficient.
temperature over 70 °C.
temperature under -20 °C.
module, open circuit. This bit is for thermocouple module only.
0 by default and should remain as 0. Contact Technical Support when the value is otherwise.
22 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 33
Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and 2080-RTD2 Chapter 3
IMPORTANT
IMPORTANT
Temperature Conversion – Data to Degree Celsius (°C)
To keep the precision of temperature value from the Thermocouple and RTD plug-in modules, there is a general data mapping conversion in the firmware before the actual temperature is sent to the Connected Components Workbench software.
The following equation shows how the Connected Components Workbench software data count is mapped from temperature Celsius degree by the firmware:
Connected Components Workbench software Data Count = (Temp (°C) +
270.0)*10;
This conversion formula applies to all types of Thermocouple and RTD sensors.
This equation illustrates how the Connected Components Workbench data count does not use full range of 0…65535 of data word.
Derive Actual Temperature °C From Connected Components Workbench Data Count:
The following formula shows how to derive temperature Celsius degree from temperature data word in the Connected Components Workbench software:
Temp (°C) = (Data - 2700)/10;
Examples:
1234 (1234 - 2700)/10 -146.6 °C 8000 (8000 - 2700)/10 530.0°C
Underrange, overrange error reporting checking is not based on Connected Components Workbench temperature data count, but the actual temperature (°C) or the voltage going into the plug-in module.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 23
Page 34
Chapter 3 Non-isolated Thermocouple and RTD Plug-in Modules – 2080-TC2 and 2080-RTD2

Notes:

24 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 35
High Speed Counter – 2080-MOT-HSC
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT
Chapter
4

Overview

The 2080-MOT-HSC plug-in module provides enhanced high speed counter capabilities to the Micro800 controller. It supports the same functionalities of an embedded high-speed counter on the Micro800 controllers but is enhanced to support up to 250 KHz 5V differential line driver for improved noise immunity and provides additional dedicated I/O.
The 2080-MOT-HSC module supports most commercial encoders (5V differential or 24V single-ended).
To configure the plug-in module, you need to download and use the HSC UDFBs from the Sample Code Library:
http://www.rockwellautomation.com/go/scmicro800
From Connected Components Workbench Release 7.0 onwards, the sample code is included in the installation and is located in the folder: \documents\public documents\ccw\samples\rockwell automation\udfb
See Quickstart Projects for 2080-MOT-HSC Plug-in step-by-step instructions on how to use the plug-in with a sample project.
From Connected Components Workbench Release 8.0 onwards, support has been added for a HSC Feedback Axis which uses the same instructions as the PTO Motion Axis. UDFBs are still supported (you can use either one but you cannot select both for the same plug­in).
on page 97 for
From Connected Components Workbench Release 11.0 onwards, support has been added for native HSCE instructions which can be used in place of the UDFBs.
With native HSCE instructions, you can configure the plug-in offline using a graphical user interface. With UDFBs, configuration is done at runtime using instructions.
2080-MOT-HSC modules with hardware revision 1.xxx only supports a value of one for Number of Pulses for rate calculation. 2080-MOT-HSC modules with hardware revision 2.xxx enhances support by enabling you to choose a value from 1...255. The hardware revision is found on the label on the module.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 25
Page 36
Chapter 4 High Speed Counter – 2080-MOT-HSC
IMPORTANT

Differences Between Embedded HSC and Plug-in Module

Counter Specifications

The following table lists the differences between the embedded HSC and the 2080-MOT-HSC plug-in module.
Embedded HSC 2080-MOT-HSC Plug-in Module
Limited to 100 kHz Up to 250 kHz
12/24V input 12/24V input or 5V differential line driver
None Embedded rate calculation using “Per Pulse” and
“Cyclic” methods
Dedicated preset and hold inputs Configure either preset or hold inputs
None One 5/24V output
When using the 2080-MOT-HSC module, the high and low preset status does not automatically reset. When using the embedded HSC, it automatically resets when the high and low preset condition no longer exists.
Filter and decode inputs: 3 input points A, B, Z
These input points may come from different types and configurations of sensors. The user must configure the module to respond to the type of sensor connected to the module as described below. This can be configured in the 2080-MOT­HSC UDFB. From Connected Components Workbench Release 8.0 onwards, if you have configured the plug-in for Feedback Axis, you can also edit the input filter values in the plug-in configuration module properties.
Nominal Filter Settings Maximum Guaranteed
Block Pulse Width
No Filter – Default
250 kHz (DC 2 µs) 617 kHz (DC 0.81 µs) 263kHz (DC 1.9 µs)
200 kHz (DC 2.5 µs) 352 kHz (DC 1.42 µs) 201 kHz (DC 2.48 µs)
80 kHz (DC 6.25 µs) 135 kHz (DC 3.7 µs) 86.2 kHz (DC 5.8 µs)
40 kHz (DC 12.5 µs) 62.5 kHz (DC 8.0 µs) 42.5 kHz (DC 11.76 µs)
13.3 kHz (DC 37.6 µs) 20.8 kHz (DC 24.1 µs) 14.1 kHz (DC 35.5 µs)
10 kHz (DC 50 µs) 15.7 kHz (DC 31.8 µs) 10.5 kHz (DC 47.2 µs)
4 kHz (DC 125 µs) 6.3 kHz (DC 79.3 µs) 4.2 kHz (DC 119 µs)
2 kHz (DC 250 µs) 3.2 kHz (DC 156 µs) 2.1 kHz (DC 237 µs)
1 kHz (DC 0.5 ms) 1.6 kHz (DC 0.31 ms) 1.0 kHz (DC 0.5 ms)
500 Hz (DC 1 ms) 778 Hz (DC 0.642 ms) 526 Hz (DC 0.95 ms)
250 Hz (DC 2 ms) 389 Hz (DC 1.285 ms) 263 Hz (DC 1.9 ms)
125 Hz (DC 4 ms) 195 Hz (DC 2.6 ms) 131 Hz (DC 3.81 ms)
62.5 Hz (DC 8 ms) 97.3 Hz (DC 5.14 ms) 65.8 Hz (DC 7.6 ms)
31.25 Hz (DC 16 ms) 48.5 Hz (DC 10.3 ms) 32.9 Hz (DC 15.2 ms)
50% duty
Minimum Guaranteed Pass Pulse Width
26 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 37
High Speed Counter – 2080-MOT-HSC Chapter 4
IMPORTANT
IMPORTANT
A
B
Z
Counter
HSC_Mode = 2 to 11
A
Z
Counter
HSC_Mode = 0, 1, 12, and 13
Counter
B
For low frequency pulses, filter times should be set appropriately to avoid extra pulses from a noisy environment. For high frequency pulses, shielded cable must always be used.
When the controller is power cycled, the value of the counters are reset to zero.
The counters are not reset to zero for program download. For example, if using the feedback axis, use the MC_SetPosition function block to reset the position to zero.
Number of Counters: 1 to 2
The module may be configured, using HSC_Mode, to use the inputs as 1 or 2 counters. 1 counter: A, B, Z = Counter 0 2 counters: A, Z = Counter0; B = Counter 1
Counter Pin Usage
Input Operational Modes
Mode Description
0 Up Counter – The accumulator is immediately cleared (0) when it reaches the high
1 Up Counter with external reset and hold – The accumulator is immediately cleared (0)
2 Counter with external direction.
3 Counter with external direction, reset, and hold.
4 Two input counter (up and down).
5 Two input counter (up and down) with external reset and hold.
6 Quadrature counter (phased inputs A and B).
7 Quadrature counter (phased inputs A and B) with external reset and hold.
8 Quadrature X4 counter (phased inputs A and B).
9 Quadrature X4 counter (phased inputs A and B) with external reset and hold.
10 Quadrature X2 counter (phased inputs A and B).
preset. A low preset cannot be defined in this mode.
when it reaches the high preset. A low preset cannot be defined in this mode.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 27
Page 38
Chapter 4 High Speed Counter – 2080-MOT-HSC
Input A
Input B
Input Z
Encoder or Sensor
Increment Pulse (count up)
1
2
3
4
5
6
7
8
Counter 0
(Input A)
PresentCount 1
Encoder or Sensor
Increment Pulse (count up)
Input Operational Modes
Mode Description
11 Quadrature X2 counter (phased inputs A and B) with external reset and hold.
12 Down Counter.
13 Down Counter with external reset and hold.
Up Counter
Pulses on A will cause the up counter (Counter 0). Also Pulses on B will cause the up counter (Counter 1).
Counter with External Direction
Pulses on A cause the counter to increment when B is low and decrement when B is high. When B is open or undriven, the counter will increment. See Pulse
External Direction Counting on page 29.
28 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 39
Pulse External Direction Counting
INPUT A
INPUT B
INPUT Z
Direction control
Count pulse
Incrementing Encoder or Sensor
Sensor or Switch
Count Pulse
(Input A)
Direction Control
(Input B)
Present Count
1
2
3
2
1
0
1
2
High Speed Counter – 2080-MOT-HSC Chapter 4
A B Change in Count Value
1 X (don’t care) 0
0 X (don’t care) 0
Two input counter (Up/Down Pulses)
Pulses on A causes the counter to increment. Pulses on B causes the counter to decrement. Pulses may occur at any time. Note that pulses can occur very closely (that is, much faster than plug-in scan time) that the plug-in never notices the change in count. In such cases, both counts may be ignored (the net change being zero anyway). In no case shall a pulse be lost. See the following diagram.
0 (Open or No Connection) +1
1-1
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 29
Page 40
Chapter 4 High Speed Counter – 2080-MOT-HSC
INPUT A
INPUT B
INPUT Z
Increment Pulse
(Input A)
Decrement Pulse
(Input B)
1
2
3
2
1
0 0
1
Increment Pulse (count up)
Decrement Pulse (count down)
Incrementing Encoder or Sensor
Decrementing Encoder or Sensor
Present Count
Up/Down Counting
A B Change in Count Value
0 or 1 +1
0 or 1 -1
0
00 0
Quadrature Counter (X1)
The module is compatible with 2 and 3 signal quadrature, or incremental encoders. The A and B signals are offset by 90 degrees and encode the direction of the rotation. The third signal, Z, occurs once per revolution and is often used as a home reference. The module’s use of this signal is discussed below in the Z input section.
30 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 41
Quadrature Counting
INPUT A
INPUT B
INPUT Z
Quadrature Encoder
A
B
X1
Count
X2
Count
1
2
3
4
5
6
7
8
9
10
11
12
11
10
9
8
7
6
5
4
3
2
1
0
X4
Count
High Speed Counter – 2080-MOT-HSC Chapter 4
Quadrature X4 Counter
Counter shall increment or decrement on each edge of the A and B pulses when the signal is in the positive or negative direction respectively. See previous illustration.
Quadrature X2 Counter
The counter increments or decrements on each edge of the A pulse when the signal is in the positive or negative direction respectively. See previous illustration.
Down Counter
Pulses on A will cause the down counter (Counter 0). Also pulses on B will cause the down counter (Counter 1).
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 31
Page 42
Chapter 4 High Speed Counter – 2080-MOT-HSC
INPUT A
INPUT B
INPUT Z
Decrement Pulse (count down)
Decrement Pulse (count down)
Encoder or Sensor
Encoder or Sensor
-1
-2
-3
-4
-5
-6 -7
-8
-1
-2
-3
-4
-5
-6
-7
-8
Counter 0
(Input A)
PresentCount 1
Counter 0
(Input B)
PresentCount 2
IMPORTANT
Down Counting
Z Input (Gate) Function/Touch Probe
This signal functionality supports:
Tou ch Pr ob e the present count value on the rising edge of IntZ_n to the HSC_Touch Probe term in the backplane input file.
Hold the counter at its present count value while IntZ_n = 1,
Reset the present count value on rising edge of IntZ_n.
If the module gets two or more Z pulses during a single plug-in scan the HSC_TouchProbe will be overwritten with the last stored value. There will be no indication that more than one store has occurred.
Ring or Linear Counter
The counter may be configured with the RingOrLinearCnt_n control bit to rollover at its limits (ring counter) or to stop counting and set a flag (linear counter).
0: ring counter. When the counter is a ring counter and the present count value is equal to MaxCountValue_n, the next input count in the up direction will cause the PresentCount_n to become the MinCountValue_n. This action is known as rollover. And the CountOverflow_n flag will be set to indicate that a rollover has happened. It is reset using the ResetCountOverflow bit.
32 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Conversely, when the PresentCount_n is equal to MinCountValue_n the next input count in the down direction will cause the PresentCount_n to become the MaxCountValue_n. This action is known as rollunder. The CountUnderflow_n
Page 43
High Speed Counter – 2080-MOT-HSC Chapter 4
IMPORTANT
Rollover
MinCountValue
MaxCountValue
Count Up
Count Down
MinCountValue
MaxCountValue
Underflow
Overflow
Count Down
Count Up
0
flag will be set to indicate that a rollunder has occurred. It is reset using the ResetCountUnderflow_n bit.
1: linear counter. When the counter is a linear counter and the present count value is equal to MaxCountValue_n the next input count in the up direction will activate the CountOverflow_n bit and also the PresentCount_n will remain at the MaxCountValue_n. CountOverflow_n is reset using the ResetCountOverflow_n bit.
Conversely, when the PresentCount_n is equal to MinCountValue_n the next input count in the down direction will activate the CountUnderflow_n bit and the PresentCount_n will remain at MinCountValue_n. CountUnderflow_n is reset using the ResetCountUnderflow_n bit.
The counts in overflow and underflow will not be accumulated at all. That is, even if 1000 pulses are applied while in overflow, the first pulse with the opposite direction (down in this case) will cause the counter to be decremented by 1. (The CountOverflow_n bit is only reset using the ResetCountUnderflow_n bit.)
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 33
Page 44
Chapter 4 High Speed Counter – 2080-MOT-HSC
Enabling and Disabling a Counter using the HSC_EN bit
Disabling the counter does not inhibit any HSC_ACC_Bn loading functions (preset or direct write) or any Z function.
The module continuously calculates rates for each of the counters regardless of input operational mode.
Timer
For the first two counters, a timer is used to measure the time between two successive pulses. This value is reported to the backplane as HSC_PULSE_WIDTH_Bn.
Understanding Rates
There are different applications which require rate information but there is no one perfect method for all. Generally, the user must weigh rate accuracy with the need for new information quickly.
Broadly, there are two different ways to calculate rates and optimize accuracy and speed of the rate of calculation:
Per Pulse 1/HSC_PULSE_WIDTH_B (supported through 2080-MOT-HSC plug-in) HSC_PULSE_WIDTH_Bn is reported to the user in the input array
Cyclic Number of Pulses/User Defined Time Interval (supported through Connected Components Workbench) PresentRate_n is reported to the user in the input array.
Per Pulse
The Per Pulse rate method can be very accurate if the time between pulses is large compared to the timer clock (1 µs for 2080-MOT-HSC). A timer is used to measure the time between the two successive pulses. This value is reported to the backplane as HSC_PULSE_WIDTH_Bn after each pulse. The user may invert this value to derive a rate.
Per Pulse rate = 1 / HSC_PULSE_WIDTH_B
However, when the time between pulses shrinks, two factors can distort the Per Pulse calculation of rate values:
The time between pulses is closer to measuring the clock’s frequency, making the granularity of the time increments have a greater effect on rate inaccuracy.
34 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 45
High Speed Counter – 2080-MOT-HSC Chapter 4
1 ms
1 ms
1 ms
1
2
3
4
1
2
1000 Hz
2000 Hz
1
1000 Hz
PresentCount_n
Count
PresentRate_n
0
Also, the rate may be calculated many times over during the course of one backplane scan time. This means that the rate data is obtained at a backplane scan is only that of the very last pair of pulses and disregards the other rate calculations that have happened during that interval. This is especially problematic if the pulses during the update time are unevenly spaced, the reported rate could be based entirely on two pulses which are extremely close together (a very high rate) but a third pulse was separated by a greater time (low rate).
You must understand these limitations when using HSC_PULSE_WIDTH_Bn to derive a rate.
Per Pulse Errors
Real pulses (note 1.9999 can be rounded to 2)
2 1 500 kHz 1 MHz 100%
9 10 111 kHz 100 kHz 11.1%
101 100 9.901 kHz 10.000 kHz 1.00%
1001 1000 999 Hz 1000 Hz 0.10%
9,999 10,000 100.01 Hz 100.00 Hz 0.010%
99,999 100,000 10.00010 Hz 10.00000 Hz 0.001%
(1) This table does not represent accuracy per pulse but repeatability. This repeatability can be applied in No
Filter setting.
(1)
Pulses reported by module
Real Frequency
Reported Frequency
% Error
Maximum Cyclic Rate Errors
Update Time Value Scalar
1 NA NA 20.02% 20.02% 0.210%
10 NA 20.11% 2.020% 0.210% 0.030%
Frequency
100 Hz 1 kHz 10 kHz 100 kHz 1 MHz
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 35
Page 46
Chapter 4 High Speed Counter – 2080-MOT-HSC
IMPORTANT
RA_HSCPlugIn
FBEN SlotID
NoiseFilter Mode
FBENO
IDCheck
Start Stop
Initialized
Accumulator
Rate
Maximum Cyclic Rate Errors

User Defined Function Blocks

Update Time Value Scalar
Frequency
100 Hz 1 kHz 10 kHz 100 kHz 1 MHz
100 20.01% 2.110% 0.220% 0.031% 0.012%
1000 3.010% 0.310% 0.040% 0.013% 0.010%
10,000 1.210% 0.130% 0.022% 0.011% 0.010%
For low frequency pulses, filter times should be set appropriately to avoid extra pulses from a noisy environment. For high frequency pulses, shielded cable must always be used.
UDFBs only apply if UDFB mode is selected in Connected Components Workbench software. It is recommended to use Feedback Axis (Release 8.0 or later) or native HSCE instructions (Release 11.0 or later) to configure the 2080-MOT-HSC plug-in module.
RA_HSCPlugIn
The purpose of this UDFB is to get high speed counter accumulator value and current pulse frequency.
RA_HSCPlugIn: Input and Output Parameters
Parameter Type Data Type Description
FBEN INPUT BOOL Function block Enable input
SlotID INPUT UINT Plug-in slot number.
NoiseFilter INPUT USINT 00: No filter
36 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
HSCMode INPUT USINT 0, 2 , 4, 6, 8, 10, 12
Slot ID = 1…5 (starting with the far left slot 1.)
01: 250 kHz 02: 200 kHz 03: 80 kHz 04: 40 kHz 05: 13.3 kHz 06: 10 kHz 07: 4 kHz 08: 2 kHz 09: 1 kHz 10: 500 Hz 11: 250 Hz 12: 125 Hz 13: 63.5 Hz 14: 31.25 Hz
Page 47
High Speed Counter – 2080-MOT-HSC Chapter 4
RA_EncoderFDBK
FBEN SlotID
HomePos NoiseFilter
FBENO
IDCheck
EncMode TrvPerRev
Initialized CurrentPOS
CurrentSpd
Start Stop
Accumulator
TpPosition
Direction
RA_HSCPlugIn: Input and Output Parameters
Parameter Type Data Type Description
Start INPUT BOOL Start counter.
Stop INPUT BOOL Stop the counter and clear “MaxDPos” and
FBENO OUTPUT BOOL Function block Enable output.
IDCHeck OUTPUT BOOL TRUE: HSC plug-in is at selected slot.
Initialized OUTPUT BOOL TRUE: HSC plug-in initialization finished and ready
Accumulator OUTPUT LINT Accumulator value.
Rate OUTPUT Real Current pulse rate. The rate calculation is based on
“MaxDSpd” value.
FALSE: Wrong plug-in or no plug-in at selected slot.
to execute. FALSE: HSCplug-in initialization not yet finished.
how many pulses have been counted every 10 ms.
RA_EncoderFDBK
RA_EncoderFDBK: Input and Output Parameters
Parameter Type Data
Ty pe
FBEN INPUT BOOL Function block Enable input
SlotID INPUT UINT Plug-in slot number.
HomePos INPUT REAL Home position.
NoiseFilter INPUT USINT 00 - No filter
EncMode INPUT USINT Encoder Mode. 1-X1, 2- X2, 4-X4.
ECntPerRev INPUT REAL User input to indicate how many X1 counts will be
TrvPerRev INPUT REAL The actual distance travelled when motor turns one
Start INPUT BOOL Start counter.
Stop INPUT BOOL Stop the counter and clear MaxDPos and MaxDSpd value
FBENO OUTPUT BOOL Function block enable output.
IDCheck OUTPUT BOOL TRUE: HSC plug-in is at selected slot.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 37
Initialized OUTPUT BOOL TRUE: Indicates HSC initialization has finished.
Description
Slot ID = 1…5 (starting with the far left slot 1)
Same value indicated in MC_Home instruction.
01 - 250 kHz 02 - 200 kHz 03 - 80 kHz 04 - 40 kHz 05 - 13.3 kHz 06 - 10 kHz 07 - 4 kHz 08 - 2 kHz 09 - 1 kHz 10 - 500 Hz 11 - 250 Hz 12 - 125 Hz 13 - 62.5 Hz 14 - 31.25 Hz
generated when Encoder disk turns one revolution.
revolution.
FALSE: Wrong plug-in or no plug-in at selected slot.
FALSE: Indicates HSC initialization has not finished.
Page 48
Chapter 4 High Speed Counter – 2080-MOT-HSC
RA_ServoFDBK
FBEN SlotID
HomePos NoiseFilter
FBENO
IDCheck
EcntPerRev TrvPerRev
Initialized CurrentPOS
CurrentSpd
Start Stop
Accumulator
TpPosition
Direction
RA_EncoderFDBK: Input and Output Parameters
Parameter Type Data
Description
Ty pe
CurrentPos OUTPUT REAL Current position.
CurrentSpd OUTPUT REAL Current speed (Unit = user distance per second).
Accumulator OUTPUT LINT Accumulator value.
TpPosition OUTPUT REAL Position recorded when the latest touch probe is triggered.
Direction OUTPUT SINT 1 = Forward
-1 = Reverse 0 = Not moving
RA_ServoFDBK
RA_ServoFDBK: Input and Output Parameters
Parameter Type Data
Ty pe
FBEN INPUT BOOL Function block Enable input
SlotID INPUT UINT Plug-in slot number.
HomePos INPUT REAL Home position.
NoiseFilter INPUT USINT 00: No filter
EncMode INPUT USINT Encoder Mode. 1-X1, 2- X2, 4-X4.
ECntPerRev INPUT REAL User input to indicate how many X1 counts will be
TrvPerRev INPUT REAL The actual distance travelled when motor turns one
Start INPUT BOOL Start counter.
Stop INPUT BOOL Stop the counter and clear MaxDPos and MaxDSpd value.
FBENO OUTPUT BOOL Function block enable output.
IDCheck OUTPUT BOOL TRUE: HSC plug-in is at selected slot.
Initialized OUTPUT BOOL TRUE: Indicates HSC initialization has finished.
CurrentPos OUTPUT REAL Current position.
38 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
CurrentSpd OUTPUT REAL Current speed (Unit = user distance per second).
Description
Slot ID = 1…5 (starting with the far left slot 1)
Same value indicated in MC_Home instruction.
01: 250 kHz 02: 200 kHz 03: 80 kHz 04: 40 kHz 05: 13.3 kHz 06: 10 kHz 07: 4 kHz 08: 2 kHz 09: 1 kHz 10: 500 Hz 11: 250 Hz 12: 125 Hz 13: 62.5 Hz 14: 31.25 Hz
generated when Encoder disk turns one revolution.
revolution.
FALSE: Wrong plug-in or no plug-in at selected slot.
FALSE: Indicates HSC initialization has not finished.
Page 49
High Speed Counter – 2080-MOT-HSC Chapter 4
RA_ServoFDBK: Input and Output Parameters
Parameter Type Data
Ty pe
Accumulator OUTPUT LINT Accumulator value.
TpPosition OUTPUT REAL Position recorded when the latest touch probe is triggered.
Direction OUTPUT SINT 1 = Forward
Description
-1 = Reverse 0 = Not moving
Use the 2080-MOT-HSC Module
For a step-by-step guide on how to use the Micro800 High Speed Counter plug­in, see Quickstart Projects for 2080-MOT-HSC Plug-in on page 97
.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 39
Page 50
Chapter 4 High Speed Counter – 2080-MOT-HSC

Notes:

40 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 51
DeviceNet Plug-in – 2080-DNET20
IMPORTANT
IMPORTANT
IMPORTANT
Chapter
5

Overview

The DeviceNet plug-in serves as scanner and client for explicit messaging to remote devices. The module is designed to scan devices such as:
CompactBlock™ LDX
PowerFlex® drives
E1Plus overloads
stack lights
User-defined function blocks (UDFB) are required to enable interaction between these devices.
The 2080-DNET20 DeviceNet scanner supports a maximum of 20 nodes. For example, if the scanner ID is configured to zero, the scanner would scan from 1…20. It is supported on Micro800 controllers with available plug-in slots. Only one 2080-DNET20 DeviceNet scanner is supported per controller.
Rockwell Automation recommends that only one 2080-DNET20 DeviceNet scanner be used for each network trunk-line.
If the 2080-DNET20 DeviceNet scanner is control flashed to a new major firmware version (for example, from 1.xxx to 2.xxx or vice versa), once the plug-in is successfully upgraded, power cycle the controller.
If RSLinx browsing is enabled, the CIP client messages can get timed out because the DeviceNet buffers are fully occupied by RSLinx messages. It is recommended not to have RSLinx browsing to the DeviceNet bridge if Client Messaging is required.

Status Indicators

Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 41
The DeviceNet plug-in module supports two standard DeviceNet green and red LED indicators:
Module status
Network status
Page 52
Chapter 5 DeviceNet Plug-in – 2080-DNET20
IMPORTANT
Module Status Indicator
LED state Module status Description
OFF No power There is no power present.
Flashing Green Operational Unit is starting up.
Green Unit operational Device is operating normally.
Flashing Red Minor fault. A recoverable fault is present or the module is
Red Unrecoverable fault. A non-recoverable fault is detected.
Network Status Indicator
LED state Module Status Description
OFF No power or offline There is no network power or device is not operating.
Flashing Green Idle No valid network connection has been made.
Green Online The plug-in module is operating normally and receiving
Flashing Red Connection time out One or more network connections has timed out.
Red Critical link failure The plug-in module has detected an error that makes it
undergoing firmware update.
messages.
incapable of communicating on the link (Bus Off or duplicate MAC_ID).

Network Configuration

In order to configure the DeviceNet plug-in and scan the network, you need to import user-defined function blocks (UDFBs) in your Micro800 project in Connected Components Workbench. Autoscan is used to add nodes into the scan list.
It is recommended that when Autoscan is running for the nodes in range, or for the connection to be established, the nodes should be idle without any pre-occupied connections requests.
Network Wiring
The DeviceNet specifications provide for maximum network distances for the main trunk line and drop lines, depending upon the baud rate used on the network.
Network Specifications
Baud Rate Trunk Line Length Drop Length
Maximum Distance Maximum Cumulative
Meters Feet Meters Feet Meters Feet
125k baud 420 1377 6 20 156 512
250k baud 200 656.17 6 20 78 256
500k baud 75 246 6 20 39 128
42 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 53
IMPORTANT
TIP
ON
1
23
4
5
7
6
8
Dim A
Pos. 1 Designate
Pin #1 Location
1
35
7 9 11 13
15
246
8
10
12
14
16
CONTACT CONFIGURATION
(Pos. 1 denotes Pin # 1)
Maximum power supply drop cable length is 3 m.
Recommended Cable
Flat Cable (Kwiklink lite) – Class 1 cable maximum allowable current 8A (NEC/CECode) – Class 2 cable maximum allowable current 4A (NEC/CECode)
DeviceNet Switches
2080-DNET20 Assembly Diagram
DeviceNet Plug-in – 2080-DNET20 Chapter 5
DeviceNet Address (MAC_ID) Switch Definitions
Node Address SW1 Switch Positions
345678
Switch Position Values
32168421
0 (default) OFF OFF OFF OFF OFF OFF
1 OFF OFF OFF OFF OFF ON
2 OFF OFF OFF OFF ON OFF
3 OFF OFF OFF OFF ON ON
4 OFF OFF OFF ON OFF OFF
5 OFF OFF OFF ON OFF ON
62 ON ON ON ON ON OFF
63 ON ON ON ON ON ON
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 43
Page 54
Chapter 5 DeviceNet Plug-in – 2080-DNET20
IMPORTANT
DeviceNet Baud Rate Switch Definitions
Baud Rate DR (Data Rate) SW1 Switch Position
12
125k OFF OFF
250k OFF ON
500k (default) ON OFF
Autobaud ON ON
For most applications, Rockwell Automation recommends that you use default node and baud rate settings. The DeviceNet scanner plug-in will be at node 0 and the devices will be at nodes 1...20. The baud rate will be at 500k baud and the maximum trunkline length will be 75 m (KwikLink Lite).
Power Supply
The plug-in module gets its power from the Micro800 backplane. However, the DeviceNet interface is isolated from the Micro800 system. Therefore, network power to operate the DeviceNet transceiver on the plug-in module is supplied by an external DeviceNet power supply.
If using a single power supply in the network, calculate the total current requirement of all devices in the network and add +10% for current surge. Recommended power supply is 1606-XLSDNET4.
Power Supply Cable Dropline Length
Dropline Length Allowable Current
1.5 m (5 ft) 3 A
2 m (6 ft) 2 A
3 m (10 ft) 1.5 A
4.5 m (15 ft) 1 A
6 m (20 ft) 0.75 A
44 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 55
DeviceNet Plug-in – 2080-DNET20 Chapter 5
V­Power Supply
V+
CAN_H CAN_L
V­V+
V+ broken between power supplies
only one ground
V­Power Supply
V+
Enclosure
TIP
Single Source Power Supply (End segment) Kwiklink Lite Cable
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00
0.00 0 (0)
60 (197)
120 (394)
180 (591)
240 (787)
300 (984)
360 (1181)
420 (1378)
If two or more power supplies are connected to the Kwinklink lite media (trunk cable) V+ should be broken between the two power supplies.
Grounding the network
If grounding at only one location, it is recommended that you ground at the center of the network.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 45
Single Source Power Supply – Trunkline Length and Maximum Current
Network Length in meter (ft)
0 (0) 8.00
20 (66) 8.00
40 (131) 7.01
60 (197) 4.72
80 (262) 3.56 300 (984) 0.96
100 (238) 2.86 320 (1050) 0.90
Current, max Network Length
in meter (ft)
(1)
(1)
(1)
(1)
220(722) 1.31
240 (787) 1.20
260 (853) 1.11
280 (919) 1.03
Current, max
Page 56
Chapter 5 DeviceNet Plug-in – 2080-DNET20
Dual Source Power Supply (both ends – Kwiklink Lite Cable)
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00
0.00
0 (0)
40 (131)
80 (262)
120 (394)
160 (525)
200 (656)
240 (787)
280 (919)
320 (1050)
360 (1181)
400 (1312)
Single Source Power Supply – Trunkline Length and Maximum Current
120 (394) 2.39 340 (1115) 0.85
140 (459) 2.05 360 (1181) 0.80
160 (525) 1.79 380 (1247) 0.76
180 (591) 1.60 400 (1312) 0.72
200 (656) 1.44 420 (1378) 0.69
(1) Exceeds NEC CL2/CECode 4A limit.
Dual source power supply (both ends – Kwiklink Lite Cable)
Network length in meters (ft)
0 (0) 8.00
20 (66) 8.00 240 (787) 4.30
40 (131) 8.00 260 (853) 3.97
60 (197) 8.00 280 (919) 3.69
80 (262) 8.00 300 (984) 3.44
100 (328) 8.00 320 (1050) 3.23
120 (394) 8.00 340 (1115) 3.04
140 (459) 7.35 360 (1181) 2.87
160 (525) 6.43 380 (1247) 2.72
180 (591) 5.72 400 (1312) 2.59
200 (656) 5.16 420 (1378) 2.46
(1) Exceeds NEC CL2/CECode 4A limit.
Current, max Network length
in meters (ft)
(1)
220 (722) 4.69
Current, max
46 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 57
DeviceNet Plug-in – 2080-DNET20 Chapter 5
IMPORTANT
Calculate Voltage Requirement
SUM {[(Ln * (Rc)) + (Nt * (0.005))] * In} < 4.65 V
Where:
Ln = Length in meter or feet Rc = Resistance of the cable per meter or feet (Kwiklink flat media = 0.019 ohms/meter or 0.0058/feet) Nt = Number of the node starting from 1 close to power supply and increasing.
0.005 = Nominal contact resistance used for every connection to the trunkline In = Current drawn from the cable system by the device.
To calculate for percentage of loading, divide the total voltage calculated from the above formula by 4.65.

User Defined Function Blocks

RA_DNET_MASTER
FBEN
SlotID Run
AutoScan ClearFault
FBENO
NodeAddress
BaudRate
Status
Error
ActiveNodes
ScanList0_62
Download the following 2080-DNET20 user-defined function blocks from the Sample Code Library:
http://www.rockwellautomation.com/go/scmicro800
RA_DNET_MASTER
This UDFB sets the 2080-DNET20 scanner to RUN mode.
RA_DNET_MASTER: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL TRUE: To continue reading and writing
SlotID INPUT UINT Plug-in slot number (1…5)
Run INPUT BOOL TRUE: Set the scanner to RUN mode.
AutoScan INPUT BOOL TRUE: AutoScan is enabled.
ClearFault INPUT BOOL TRUE: Clear scanner fault.
FBENO OUTPUT BOOL Function block enable output.
NodeAddress OUTPUT USINT Scanner node address. Default node
BaudRate OUTPUT USINT Network baud rate:
Status OUTPUT USINT Scanner fault status.
the scanner status. FBEN changed to level Triggered.
FALSE: Scanner is in IDLE mode. AutoScan is enabled.
FALSE: No action.
TRUE upon exit.
address is 0.
0: 125K 1: 250K 2: 500K 3: AutoBaud Default baud rate is 500K.
0: No error.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 47
Page 58
Chapter 5 DeviceNet Plug-in – 2080-DNET20
FBEN
SlotID NodeID
FBENO
RA_DNET_NODE_STATUS
Status
Error
RA_DNET_MASTER: Input and Output Parameters
Variable Name Type Data Type Description
Error OUTPUT STRING Scanner error description.
ActiveNodes OUTPUT USINT Number of slave nodes in the network.
Scanlist0_62 OUTPUT LWORD Details on active node table, bit 0…62.
Bit 0: Represent Node 0. Bit 62: Represent Node 62.
Sequence of Operation: RA_DNET_MASTER
Sequence Run Autoscan Description
1 False False Reinitializes scan list from the plug-in scanner if
FBEN = TRUE.
2 False True Triggers autoscan to scan the network after clearing
scan list.
3 False False Puts scanner to IDLE mode by disabling autoscan if
active node number = number of nodes in network.
4 True False Puts scanner to RUN mode.
Upon powerup, the scanner should be in IDLE Mode for the autoscan to start. Wait until the autoscan process is complete before turning the scanner to RUN Mode (that is, Run bit is TRUE).
Sample Code
RA_DNET_NODE_STATUS
This UDFB is used to read the node status of slave nodes in a DeviceNet network where the 2080-DNET20 scanner is connected.
48 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 59
DeviceNet Plug-in – 2080-DNET20 Chapter 5
FBEN
SlotID NodeID
FBENO
RA_DNET_LDX_DISCRETE
DI_Module1 DI_Module2
Module1 Module2
Module3
DO_Module2 DO_Module3
Module4
DO_Module4
DO_Module1
DI_Module3 DI_Module4
RA_DNET_NODE_STATUS: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
TRUE to enable the function.
SlotID INPUT UINT Plug-in slot number (1…5)
NodeID INPUT USINT Slave node address.
FBENO OUTPUT BOOL Function block enable output.
TRUE upon exit.
Status OUTPUT USINT Scanner fault status.
0: No errors.
Error OUTPUT STRING Description of the node status error.
Sample Code: RA_DNET_NODE_STATUS
RA_DNET_LDX_DISCRETE
This UDFB is used for I/O data exchange with discrete CompactBlock I/O.
RA_DNET_LDX_DISCRETE: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
SlotID INPUT UINT Plug-in slot number (1…5)
NodeID INPUT USINT Node address of the digital Compact I/O slave node.
Module1 INPUT STRING Base module I/O configuration.
Module2 INPUT STRING Expansion module 1 I/O configuration.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 49
TRUE to enable the function block.
INPUT X OUTPUT Channels For example: 16X0 (16 input / 0 output is physically present as base module) Valid String: 32X0, 0X32, 16X0, 0X16, 16X16, 8X8, 8X0, 0X8, 0X6 NOTE: X should always be upper case.
INPUT X OUTPUT channels For example: 16X0 (16 input / 0 output is physically present as base module) Valid String: 32X0, 0X32, 16X0, 0X16, 16X16, 8X8, 8X0, 0X8, 0X6 NOTE: X should always be upper case.
Page 60
Chapter 5 DeviceNet Plug-in – 2080-DNET20
FBEN
SlotID NodeID
FBENO
RA_DNET_LDX_ANALOG
AI_CH0 AI_CH1
AI_CH2
AI_CH3
StatusCH0_3
DI_Module2 DI_Module3
Module1 Module2 Module3
AO_Ch0 AO_Ch1
DO_Module2
DO_Module3
RA_DNET_LDX_DISCRETE: Input and Output Parameters
Variable Name Type Data Type Description
Module3 INPUT STRING Expansion module 2 I/O configuration.
INPUT X OUTPUT Channels For example: 16X0 (16 input / 0 Output is physically present as base module) Valid String: 32X0, 0X32, 16X0, 0X16, 16X16, 8X8, 8X0, 0X8, 0X6 NOTE: X should always be upper case.
Module4 INPUT STRING Expansion module 3I/O configuration.
INPUT X OUTPUT Channels For example: 16X0 (16 input / 0 output is physically present as base module) Valid String: 32X0, 0X32, 16X0, 0X16, 16X16, 8X8, 8X0, 0X8, 0X6 NOTE: X should always be upper case.
DO_Module1 INPUT UDINT Output data for base module.
DO_Module2 INPUT UDINT Output data for expansion module 1.
DO_Module3 INPUT UDINT Output data for expansion module 2.
DO_Module4 INPUT UDINT Output data for expansion module 3.
FBENO OUTPUT BOOL Function block enable output.
TRUE upon exit.
DI_Module1 OUTPUT UDINT Input data from base module (Module 1).
DI_Module2 OUTPUT UDINT Input data from expansion module 1
(Module 2).
DI_Module3 OUTPUT UDINT Input data from expansion module 2
(Module 3).
DI_Module4 OUTPUT UDINT Input data from expansion module 3
(Module 4).
RA_DNET_LDX_ANALOG
This UDFB is used for data exchange with analog CompactBlock I/O.
RA_DNET_LDX_ANALOG: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
SlotID INPUT UINT Plug-in slot number (1…5)
NodeID INPUT USINT Slave node address.
(1)
Module1
Module2
(1)
INPUT STRING Analog base module I/O configuration.
INPUT STRING Digital expansion module 1 I/O configuration.
50 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
TRUE to enable the function.
INPUT X OUTPUT Channels For example: 4X0 (4 input analog module is physically present as base module) Valid String: 0X2, 4X0 NOTE: X should always be upper case.
INPUT X OUTPUT Channels For example: 16X16 (16 input / 16 output is physically present as expansion module 1) Valid String: 16X0, 0X16, 16X16, 8X8, 8X0, 0X8, 0X6 NOTE: X should always be upper case.
Page 61
DeviceNet Plug-in – 2080-DNET20 Chapter 5
FBEN
SlotID NodeID
FBENO
CH0
CH1 CH2
CH3
StatusCH0_3
RA_DNET_LDX_TC_RTD
RA_DNET_LDX_ANALOG: Input and Output Parameters
Variable Name Type Data Type Description
(1)
Module3
AO_Ch0 INPUT WORD Analog Output Channel 0 value.
AO_Ch0 INPUT WORD Analog Output Channel 1 value.
DO_Module2 INPUT UINT Output data for Expansion Module 1.
DO_Module3 INPUT UINT Output Data for Expansion Module 2.
FBENO OUTPUT BOOL Function block enable output.
AI_CH0 OUTPUT WORD Analog Input Channel 0 value.
AI_CH1 OUTPUT WORD Analog Input Channel 1 value.
AI_CH2 OUTPUT WORD Analog Input Channel 2 value.
AI_CH3 OUTPUT WORD Analog Input Channel 3 Value.
StatusCH0_3 OUTPUT WORD Analog input channel 0…3 status
DI_Module2 OUTPUT UINT Digital Expansion Module 1 Input Data.
DI_Module3 OUTPUT UINT Digital Expansion Module 2 Input Data.
INPUT STRING Digital expansion module 2 I/O configuration.
INPUT X OUTPUT channels For example: 16X16 (16 input / 16 output is physically present as expansion module 2) Valid String: 16X0, 0X16, 16X16, 8X8, 8X0, 0X8, 0X6 NOTE: X should always be upper case.
This value is valid only if Module1 = '0X2'
This value is valid only if Module1 = '0X2'
TRUE upon exit.
This value is valid only if Module1 = '4X0'
This value is valid only if Module1 = '4X0'
This value is valid only if Module1 = '4X0'
This value is valid only if Module1 = '4X0'
Applicable only if catalog is with digital inputs.
Applicable only if catalog is with digital inputs.
(1) Use only valid strings combinations as mentioned above. If Module1, Module2, Module3 physical I/O does not
match the physical I/O present in base and expansion, then incorrect sequence will be written.
RA_DNET_LDX_TC_RTD
This UDFB is used to read input data from the Thermocouple/RTD module.
RA_DNET_LDX_TC_RTD: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
SlotID INPUT UINT Plug-in slot number (1…5)
NodeID INPUT USINT Node address of the digital Compact I/O slave node.
FBENO OUTPUT BOOL Function block enable output.
CH0 OUTPUT WORD RTD/Thermocouple input channel 0 value.
CH1 OUTPUT WORD RTD/Thermocouple input channel 1 value.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 51
TRUE to enable function.
Page 62
Chapter 5 DeviceNet Plug-in – 2080-DNET20
FBEN
PlcPortNum
Start Stop
ReferenceSpeed
Jog ClearFault
Fwd_Rev
FBENO
RA_PF_DNET_STANDARD
DriveNodeNum
Status
PF_Feedback
PF_ErrorCode
PF_Ready
PF_Active
PF_Alarm
PF_Fault
PF_AltReference
RA_DNET_LDX_TC_RTD: Input and Output Parameters
Variable Name Type Data Type Description
CH2 OUTPUT WORD RTD/Thermocouple input channel 2 value.
CH3 OUTPUT WORD RTD/Thermocouple input channel 3 value.
StatusCH0_3 OUTPUT WORD RTD/Thermocouple Input channel 0…3 status.
RA_DNET_TOWERLIGHT
FBEN
SlotID NodeID
Light_0_4
FBENO
Status_0_4
RA_DNET_TOWERLIGHT
This UDFB is used for data exchange with a towerlight or stacklight.
RA_DNET_TOWERLIGHT: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
SlotID INPUT UINT Plug-in slot number (1…5)
NodeID INPUT USINT Towerlight node address.
Light_0_4 INPUT USINT Light 0…4, for example:
FBENO OUTPUT BOOL Function block enable output.
Status_0_4 OUTPUT USINT Light 0…4 status.
TRUE to enable the function.
Bit 0: Blue Bit 1: Yellow Bit 2: Red
TRUE upon exit.
RA_PF_DNET_STANDARD
This UDFB is used for I/O data exchange with standard PowerFlex drives configured as single mode.
RA_PF_DNET_STANDARD: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
PlcPortNum INPUT UINT Plug-in slot number (1…5 for plug-in slots).
DriveNodeNum INPUT USINT Slave node address for PowerFlex drive.
Start INPUT BOOL TRUE to start PowerFlex drive.
Stop INPUT BOOL TRUE to stop PowerFlex drive.
ReferenceSpeed INPUT REAL Reference speed for the device.
Jog INPUT BOOL TRUE to enable jog in PowerFlex drive.
ClearFault INPUT BOOL TRUE to clear fault in PowerFlex drive.
Fwd_Rev INPUT BOOL TRUE to configure PowerFlex drive for forward motion.
52 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
FBENO OUTPUT BOOL Function block enable output.
TRUE to enable the function.
Configure PowerFlex drive speed.
FALSE to configure PowerFlex drive for reverse motion.
TRUE upon exit.
Page 63
DeviceNet Plug-in – 2080-DNET20 Chapter 5
IMPORTANT
RA_PFDNET_MULTIDRIVE
FBEN PlcPortNum
NodeNum
Start Stop
ReferenceSpeed
Jog ClearFault
Fwd_Rev
FBENO
PF_Feedback
PF_Ready PF_Active
PF_Alarm
PF_Fault
PF_AltReference
RA_PF_DNET_STANDARD: Input and Output Parameters
Variable Name Type Data Type Description
Status OUTPUT BOOL PowerFlex drive status.
PF_Feedback OUTPUT REAL Feedback from the PowerFlex drive.
PF_ErrorCode OUTPUT INT For future use.
PF_Ready OUTPUT BOOL Ready bit from PowerFlex drive.
PF_Active OUTPUT BOOL Active bit from PowerFlex drive.
PF_Alarm OUTPUT BOOL Alarm bit from PowerFlex drive.
PF_Fault OUTPUT BOOL Fault bit from PowerFlex drive.
PF_AltReference OUTPUT BOOL Alt Reference bit from PowerFlex drive.
Ensure that your PowerFlex drives settings are correct. For basic setup configuration, see the PowerFlex drives user manuals in the
Rockwell Automation Literature Library
.
With PowerFlex 523, you need to multiply the speed reference and divide the speed feedback by a factor of 10.0 in order to get the correct value. Note that the PowerFlex 4 and PowerFlex 5 drives have a different multiplier.
Reference and Feedback for the Different PowerFlex Drives
Drive Type Number Reference Feedback
PowerFlex 4M 132 x10 x0.1
PowerFlex 4 39 x10 x0.1
PowerFlex 40 40 x100 x0.1
PowerFlex 40P 41 x100 x0.01
PowerFlex 400 129 x100 x0.01
PowerFlex 523 8 x100 x0.01
PowerFlex 525 9 x100 x0.01
For example, if you set reference speed at 50, command speed is 50 Hz for PowerFlex 4M and only 5 Hz for PowerFlex 523 and PowerFlex 525.
RA_PF_DNET_MULTIDRIVE
This UDFB is used for I/O data exchange with standard PowerFlex drives, configured as multi-drive.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 53
Page 64
Chapter 5 DeviceNet Plug-in – 2080-DNET20
RA_PF_DNET_MULTIDRIVE: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
TRUE to enable the function.
PlcPortNum INPUT UINT Plug-in slot number (1…5 for plug-in slots).
NodeNum INPUT USINT DeviceNet node address for PowerFlex drive
(connected as master in multi-drive setup).
Start INPUT BOOL[1…5] TRUE to start each element of the array.
Corresponds to each drive. For example: Start[1] for Drive 1 and Start[5] for Drive5.
Stop INPUT BOOL[1…5] TRUE to stop each element of the array.
Corresponds to each drive, for example, Stop [1] for Drive 1 and Stop [5] for Drive5.
ReferenceSpeed INPUT REA[1...5]L Reference speed to set the device speed.
Each element of the array corresponds to each drive, for example, Reference Speed [1]
for Drive 1 and Reference Speed [5] for Drive5.
Jog INPUT BOOL[1...5] TRUE to enable jog in PowerFlex drive.
Each element of the array corresponds to each drive, for example, Reference Jog [1] for Drive 1 and Jog [5] for Drive5.
ClearFault INPUT BOOL[1...5] TRUE to clear fault in PowerFlex drive.
Each element of the array corresponds to each drive, for example, ClearFault [1] for Drive 1 and ClearFault [5] for Drive5.
Fwd_Rev INPUT BOOL[1...5] TRUE to configure PowerFlex drive for forward
motion. FALSE to configure PowerFlex drive for Reverse motion. Each element of the array corresponds to each drive, for example, Fwd_Rev [1] for Drive 1 and Fwd_Rev [5] for Drive5.
FBENO OUTPUT BOOL Function block enable output.
TRUE upon exit.
PF_Feedback OUTPUT REAL[1...5] Speed reference from the PowerFlex drive.
Each element of the array corresponds to each drive, for example, PF_Feedback[1] for Drive 1 and PF_Feedback[5] for Drive5.
PF_Ready OUTPUT BOOL[1...5] Ready bit from PowerFlex drive.
Each element of the array corresponds to each drive, for example, PF_Ready[1] for Drive 1 and PF_Ready[5] for Drive5.
PF_Active OUTPUT BOOL[1...5] Active bit from PowerFlex drive.
Each element of the array corresponds to each drive, for example, PF_Active[1] for Drive 1 and PF_Active[5] for Drive5.
54 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 65
DeviceNet Plug-in – 2080-DNET20 Chapter 5
IMPORTANT
RA_DNET_OVERLOAD
FBEN SlotID
NodeID
OutA TripReset
FBENO
IN1
IN2
Warning
Tripped
AverageFLA
ThernUtilized
OutAStart
RA_DNET_GENERIC
FBEN SlotID
NodeID
OutputData
FBENO
InputData
RA_PF_DNET_MULTIDRIVE: Input and Output Parameters
Variable Name Type Data Type Description
PF_Alarm OUTPUT BOOL[1...5] Alarm bit from PowerFlex drive.
Each element of the array corresponds to each drive, for example, PF_Alarm[1] for Drive 1 and PF_Alarm[5] for Drive5.
PF_Fault OUTPUT BOOL[1...5] Fault bit from PowerFlex drive.
Each element of the array corresponds to each drive, for example, PF_Fault[1] for Drive 1 and PF_Fault[5] for Drive5.
PF_AltReference OUTPUT BOOL[1...5] Alt Reference bit from PowerFlex drive.
Each element of the array corresponds to each drive, for example, PF_AltReference[1] for Drive 1 and PF_AltReference[5] for Drive5.
Ensure that your PowerFlex drives settings are correct. For basic setup configuration, see the PowerFlex drives user manuals in the
Rockwell Automation Literature Library
.
RA_DNET_OVERLOAD
This UDFB is used for I/O data exchange with an overload relay.
RA_DNET_OVERLOAD: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
SlotID INPUT UINT Plug-in slot number (1…5 for plug-in slots).
NodeID INPUT USINT DeviceNet node address of the slave node.
OutA INPUT BOOL TRUE to turn on Output A.
TripReset INPUT BOOL TRUE to enable Trip Reset.
FBENO OUTPUT BOOL Function block enable output.
IN1 OUTPUT BOOL Input 1 from overload relay.
IN2 OUTPUT BOOL Input 2 from overload relay.
Warning OUTPUT BOOL TRUE if warning is enabled.
Tripped OUTPUT BOOL TRUE if tripped.
AverageFLA OUTPUT WORD Average FLA % value from overload relay.
ThermUtilized OUTPUT WORD Therm Utilized value from overload relay.
OutAStatus OUTPUT WORD Average FLA value from overload relay.
TRUE to enable the function.
TRUE upon exit.
RA_DNET_GENERIC
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 55
This UDFB is used for I/O data exchange with generic I/O devices.
Page 66
Chapter 5 DeviceNet Plug-in – 2080-DNET20
IMPORTANT
RA_DNET_EXPLICIT
FBEN SlotID
NodeID CnxnNumber
FBENO
InputData
MsgLength CIPService CIPClass CIPInstance
CIPAttribute
Q
ResponseData
Status
RequestData
RA_DNET_GENERIC: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
TRUE to enable function.
SlotID INPUT UINT Plug-in slot number (1…5 for plug-in slots).
NodeID INPUT USINT Slave node address.
OutputData INPUT USINT[1…64] Slave output data.
FBENO OUTPUT BOOL Function block enable output.
TRUE to enable function.
InputData[1…64] OUTPUT USINT[1…64] Input data from slave.
RA_DNET_EXPLICIT
This UDFB is used for sending explicit message to slave node.
For DNET explicit message, the maximum payload supported is 256 bytes.
RA_DNET_EXPLICIT: Input and Output Parameters
Variable Name Type Data Type Description
FBEN INPUT BOOL Function block enable input.
SlotID INPUT UINT Plug-in slot number (1…5 for plug-in slots).
NodeID INPUT USINT Node address of slave node.
CnxnNumber INPUT USINT Connection number values 1, 2, 3, 4, 5.
MsgLength INPUT USINT Specifies the size of the CIP message in the
CIPService INPUT UINT CIP service code.
CIPClass INPUT UINT CIP Class code (valid values 0…65535).
CIPInstance INPUT UINT CIP instance (valid values 0…65535).
CIPAttribute INPUT UINT CIP attribute (valid values 0…65535).
RequestData INPUT USINT[1…54] Request data from slave.
FBENO OUTPUT BOOL Function block enable output.
Q OUTPUT BOOL TRUE when message is sent out successfully.
Error OUTPUT BOOL TRUE when message transmits error.
ResponseData OUTPUT USINT
[1...50]
TRUE to enable function.
transaction block.
CIP Response error Response Data[1] : Extended Error ID Response Data[2] : Error ID
See Explicit Message Request Format
on page 57.
See Explicit Message Status Codes on page 57.
Status OUTPUT USINT See Explicit Message Status Codes on page 57.
56 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 67
Transaction Block Format
Byte Offset Contents
0Status
1 Transaction ID
2Size
3 Reserved
4MAC ID
5 Service
6…115 Transaction Body (110 bytes)
Explicit Message Request Format
Byte Offset Contents
0 Status
1 Transaction ID
2Size
3 Reserved
4 MAC ID
5 Service
6…7 Class
8…9 Instance
10…115 Service Data (106 Bytes)
DeviceNet Plug-in – 2080-DNET20 Chapter 5
Explicit Message Response Format
Byte Offset Contents
0 Status
1 Transaction ID
2Size
3Reserved
4MAC ID
5Service
Byte Offset Contents Request Data
0 Status Can be read from UDFB status
6…115 ServiceData Can be read from UDFB response data.
Explicit Message Status Codes
Status Code Description
0 Ignore transaction block (block empty).
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 57
Response data shows CIP error Code.
Page 68
Chapter 5 DeviceNet Plug-in – 2080-DNET20
IMPORTANT
Explicit Message Status Codes
1 Transaction completed successfully.
2 Transaction in progress (not ready).
4 Error – node offline
5 Error – DeviceNet port disabled/offline
6 Error – Transaction TXID unknown
7 Error – Duplicate TXID
9 Error – Scanner out of buffers
12 Error – Response data too large for block
14 Error – Invalid size specified
15 Error – Device timed out
16 Block queued.
17 Block allocated
18 Connection in progress
3, 8, 10, 11, 13, 19...255 Reserved

Send Explicit Messages to 2080-DNET20 Plug-in Using Micro800 Pass Through

MSG_CIPGENERIC instruction can be used to send Explicit messages to the 2080-DNET20 plug-in and the Slave nodes on the DeviceNet network.
For DeviceNet messaging using MSG_CIPGENERIC, only unconnected messaging (connection mode 0) is supported. CIP connection type must be configured as 0 – unconnected.
In MSG_CIPGENERIC, configure the target path as mentioned below:
To access the plug-in, the format of the target path is “1, Slot number”.
To access a Slave device through the plug-in, the format of the target path is
“1, Slot number, 2, DeviceNet node address”.
For example, if the 2080-DNET20 plug-in is connected at physical slot 3 and the Slave device of address 40 is present in the DeviceNet network, then:
Using MSG_CIPGENERIC to access the plug-in, the target path would be “1, 3”.
Using MSG_CIPGENERIC to access the Slave node through the plug-in, the target path would be “1, 3, 2, 40”.
Note that the number “1” refers to the Virtual backplane port number and “2” refers to the 2080-DNET20 plug-in's DeviceNet port number. These are fixed values. The slot number starts from 1 up to the maximum number of slots physically present in the controller.
When the controller pass through feature is used in the following example:
Micro850 –> Micro820 [192.168.1.100] –> 2080-DNET20 plug-in [Slot 3] –> Slave device [Node 40]
58 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 69
DeviceNet Plug-in – 2080-DNET20 Chapter 5
IMPORTANT
Using MSG_CIPGENERIC starting from Micro850 to access the plug­in, the target path would be “4, 192.168.1.100, 1, 3”
Using MSG_CIPGENERIC starting from Micro850, the Slave device cannot be accessed because the MSG_CIPGENERIC target path configuration is limited to a single hop. This path will work if you use a Logix controller/PC instead of Micro850.
Note that the number “4” refers to the EtherNet/IP port number (for Serial the port number varies from 2...5. See the controller’s user manual for detailed information).
To use the controller pass through feature, the following firmware revisions are required:
Micro820/Micro830/Micro850 controller firmware revision 8.011 or
higher.
2080-DNET20 plug-in firmware revision 2.011 or higher.

Error Codes

DeviceNet plug-in Error Codes and Descriptions
ErrorID Description
0 No errors.
1 Node number not in scanlist.
65 AutoScan active.
70 Scanner failed DUP MAC check.
71 Illegal value in scanlist.
72 Device stopped communicating.
73 Device does not match scanlist.
74 Scanner has detected data overrun.
75 No network traffic detected.
76 No network traffic detected for scanner.
77 Data size returned does not match scanlist.
78 Device on scanlist not active on subnet.
79 Scanner failed to transmit a message.
80 Scanner is in Idle mode operation.
81 Scanner is in fault mode operation.
82 I/O fragment out of sequence.
83 Device refused to be initialized.
84 Device not yet initialized.
85 Incorrect data size upon connection with device.
86 Device/Slave went into Idle.
87 Shared master has not allocated slave.
88 Shared master has not allocated required choices.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 59
Page 70
Chapter 5 DeviceNet Plug-in – 2080-DNET20
DeviceNet plug-in Error Codes and Descriptions
ErrorID Description
89 Keeper download failed.
90 User has disabled scanner.
91 Bus Off detected on scanner.
92 No network power detected.
93 CRC failure detected on one or more
configuration blocks.
95 Scanner application program flash is being updated.
96 Port is in test mode.
97 Scanner is halted by user.
98 ESC, overflow, divide or other processor error.
99 Scanner watchdog has timed out.
Use the 2080-DNET20 Plug-in
For a step-by-step guide on how to use the DeviceNet plug-in, see Quickstart
Project for 2080-DNET20 Plug-in on page 92.
60 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 71
Specifications
Appendix
A

Digital Plug-in Modules

General Specifications – 2080-OB4, 2080-OV4, 2080-IQ4OB4, 2080-IQ4OV4, 2080-IQ4
Attribute Value
Mounting torque 0.2 Nm (1.48 lb-in.)
Status indicators For input or output modules – 4 yellow
Terminal base screw torque 0.22…0.25 Nm (1.95…2.21 lb-in.)
Enclosure type rating None (open-style)
Isolation voltage For input modules
Wire size 1.3... 0.2 mm
Wire category 2 – on signal ports
North American temp code T4
For combination modules – 8 yellow
using a 2.5 mm (0.10 in.) flat-blade screwdriver
50V (continuous), Basic Insulation Type, Inputs to Backplane Type tested for 60 s @ 720 V DC, Inputs to Backplane
For combination or output modules
50V (continuous), Basic Insulation Type, Inputs to Outputs, I/Os to Backplane
Type tested for 60 s @ 720 V DC, I/Os to Backplane
2
90 °C (194 °F), or greater, insulation max
2 – on power ports
(16...24 AWG) solid or stranded copper wire rated @
Input Specifications – 2080-IQ4, 2080-IQ4OV4, 2080-IQ4OB4
Attribute Value
DC on-state voltage, min 9.0V DC
DC on-state voltage, max 30V DC
DC on-state current, min 2.0 mA @ 9V DC
DC on-state current, nom 3.0 mA @ 24V DC
DC on-state current, max 5.0 mA
DC off-state voltage, max 5V DC
DC off-state current, max 1.5 mA
IEC input compatibility Type 3
Input impedance 0…3V, >4 K
Input filter time ON to OFF 8…10 ms AC/DC
AC on-state voltage, min 10.25V AC (rms)
AC on-state voltage, max 30V AC (rms)
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 61
3…12V, 3.5 K min 12…30V, >4 K <10 K
Page 72
Appendix A Specifications
Input Specifications – 2080-IQ4, 2080-IQ4OV4, 2080-IQ4OB4
Attribute Value
AC on-state current, min 2.0 mA @ 9V AC (rms)
AC on-state current, max 5.0 mA
AC off-state voltage 3.5V AC (rms)
Output Specifications – 2080-OB4, 2080-OV4, 2080-IQ4OB4, 2080-IQ4OV4
Attribute Value
Power supply voltage 10.8V DC, min
30V DC, max
On-state voltage 10V DC, min
24V DC, nom 30V DC, max
On-state current 5.0 mA @ 10V DC, min
0.5 A max, steady state 2 A surge, 2 s min
Off-state leakage current, max 10 µA
Environmental Specifications – 2080-OB4, 2080-OV4, 2080-IQ4OB4, 2080-IQ4OV4, 2080-IQ4
Attribute Value
Temperature, operating IEC60068-2-1 (Test Ad, Operating Cold),
Temperature, surrounding air, max.
Temperature, non-operating IEC60068-2-1 (Test Ad, Operating Cold),
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
Vibration IEC 60068-2-6 (Test Fc, Operating):
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Shock, non-operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Emissions CISPR 11:
ESD Immunity IEC 61000-4-2:
Radiated RF immunity IEC 61000-4-3:
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20...65 °C (-4…149 °F)
65 °C (149 °F)
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-40...85 °C (-40…185 °F)
5…95% noncondensing
2 g @ 10…500 Hz
25 g
25 g
Group 1, Class A
6 kV contact discharges 8 kV air discharges
10 V/M with 1 kHz sine-wave 80%AM from 80…2000 MHz 10 V/M with 200 Hz 50% Pulse 100%AM @ 900 MHz 10 V/M with 200 Hz 50% Pulse 100%AM @1890 MHz 10 V/M with 1 kHz sine-wave 80%AM from 2000…2700 MHz
62 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 73
Specifications Appendix A
Environmental Specifications – 2080-OB4, 2080-OV4, 2080-IQ4OB4, 2080-IQ4OV4, 2080-IQ4
Attribute Value
EFT/B immunity ±2 kV @ 5 kHz on signal ports
Surge transient immunity ±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports
Conducted RF immunity 10V rms with 1 kHz sine-wave 80%AM from 150 kHz…80 MHz
Certifications – 2080-OB4, 2080-OV4, 2080-IQ4OB4, 2080-IQ4OV4, 2080-IQ4
Certification (when product is marked)
(1)
Value
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
CE European Union 2014/30/EU EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
KC Korean Registration of Broadcasting and Communications
Equipment, compliant with: Article 58-2 of Radio Waves Act, Clause 3
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/
for Declarations of Conformity, Certificates, and other certification details.
General Specifications – 2080-OW4I Digital Relay Output Plug-in Module
Attribute Value
Mounting torque 0.2 Nm (1.48 lb-in.)
Status indicators 4 yellow
Terminal base screw torque, max
Wire size 0.05…1.31 mm
0.19 Nm (1.7 lb-in.) using a 2.5 mm [0.10 in.] flat-blade screwdriver
2
(30…16 AWG) solid copper wire
rated @ 90 °C (194 °F ) insulation max
Enclosure type rating None (open-style)
Isolation voltage 240V (continuous), Reinforce Insulation Type, between Output
Channels and Output channels to Backplane Type tested for 60 s @ 1480 V AC Outputs to Outputs, Outputs to
Backplane
Insulation stripping length 5 mm
Wiring category 2 – on signal ports
2 – on power ports
Wire type Copper
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 63
Page 74
Appendix A Specifications
General Specifications – 2080-OW4I Digital Relay Output Plug-in Module
Attribute Value
North American temp code T4
Inrush current <120 mA @ 3.3V
Backplane power 3.3 VDC, 38 mA
Output current, resistive 2 A @ 5…30V DC
Output current, inductive 1.0 A steady state @ 5…28V DC
Output power, resistive, max 250 VA for 125V AC resistive loads
Pilot duty rating C300, R150
Minimum load, per point 10 mA
Initial contact resistance of relay, max
Output delay time, max 10 ms ON or OFF
<120 mA @ 24V
0.5 A @ 48V DC
0.22 A @ 125V DC 2 A @ 125V AC 2 A @ 240V AC
0.93 A steady state @ 30V DC
0.5 A steady state @ 48V DC
0.22 A steady state @ 125V DC
2.0 A steady state, 15 A make @ 125V AC, PF – cos θ = 0.4
2.0 A steady state, 7.5 A make @ 240V AC, PF – cos θ = 0.4
480 VA for 240V AC resistive loads 60 VA for 30V DC resistive loads 24 VA for 48V DC resistive loads
27.5 VA for 125V DC resistive loads
30 m
Relay Contact Ratings (0.35 power factor) – 2080-OW4I
Maximum Volts Amperes Amperes
Continuous
Make Break Make Break
120V AC 15 A 1.5 A 2.0 A 1800 VA 180 VA
240V AC 7.5 A 0.75 A
24V DC 1.0 A 28 VA
125V DC 0.22 A
Volt-Amperes
64 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 75
Relay Life Chart for 2080-OW4I
AC 250 V cos φ = 0.4
AC 125 V cos φ = 0.4
AC 125 V resistive load
AC 250 V resistive load
DC 30 V resistive load
DC 30 V T = 7 ms
0.5 1.0 2.0 3.0
5
3
10
20
30
50
100
Switching capacity (A)
Number of operations (X10)
Relay life
Specifications Appendix A
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 65
Page 76
Appendix A Specifications
Environmental Specifications – 2080-OW4I
Attribute Value
Temperature, operating IEC60068-2-1 (Test Ad, Operating Cold),
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20...65 °C (-4…149 °F)
Temperature, surrounding air,
65 °C (149 °F)
max.
Temperature, non-operating IEC60068-2-1 (Test Ad, Operating Cold),
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-40...85 °C (-40…185 °F)
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5…95% noncondensing
Vibration IEC 60068-2-6 (Test Fc, Operating):
2 g @ 10…500 Hz
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
10 g
Shock, non-operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
DIN rail mounting: 25 g Panel mounting: 35 g
ESD Immunity IEC 61000-4-2:
6kV contact 8 kV air
Radiated RF immunity IEC 61000-4-3
10 V/M with 1 kHz sine-wave 80%AM from 80…2000 MHz 10 V/M with 200 Hz sine-wave 50% Pulse 100%AM @ 900 MHz 10 V/M with 200 Hz sine-wave 50% Pulse 100%AM @1890 MHz 10 V/M with 1 kHz sine-wave 80%AM from 2000…2700 MHz
EFT/B immunity IEC 61000-4-4:
±2 kV @ 5 kHz on signal ports
Surge transient immunity IEC 61000-4-5:
±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1 kHz sine-wave 80%AM from 150 kHz…80 MHz
66 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 77
Certifications – 2080-OW4I
Specifications Appendix A
Certification (when product is marked)
(1)
Value
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
CE European Union 2014/30/EU EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
European Union 2014/35/EU LVD, compliant with:
EN 61131-2; Programmable Controllers (Clause 11)
RCM Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
KC Korean Registration of Broadcasting and Communications
Equipment, compliant with: Article 58-2 of Radio Waves Act, Clause 3
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declarations of Conformity, Certificates, and other certification details.

Analog Plug-in Modules

Input Specifications – 2080-IF2, 2080-IF4
Attribute 2080-IF2 2080-IF4
Number of inputs, single ended
Analog normal operating ranges
Resolution, max. 12 bits unipolar, with software selected option for 50 Hz,
Data range 0…65535
Input impedance Voltage Terminal: > 220K , Current Terminal: 250
Overall accuracy
(1)
Non-linearity (in percent full scale)
Repeatability
(2)
Module error over full temperature range, -20…65°C (-4…149°F)
Input channel configuration Through configuration software or the user program
Field input calibration Not required
Update time 180 ms per enabled channel
24
Voltage: 0…10V DC Current: 0…20 mA
60 Hz, 250 Hz, 500 Hz
Voltage Terminal: ±1% full scale @ 25°C Current Terminal: ±1% full scale @ 25°C
± 0.1%
± 0.1%
Voltage: ± 1.5% Current: ± 2.0%
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 67
Page 78
Appendix A Specifications
Input Specifications – 2080-IF2, 2080-IF4
Attribute 2080-IF2 2080-IF4
Input group to bus isolation No isolation
Channel to channel isloation Non-isolation
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20...65 °C (-4…149 °F)
Temperature, non-operating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat), IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40...85 °C (-40…185 °F)
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5%...95% non-condensing
Vibration IEC 60068-2-6 (Test Fc, Operating):
2g @ 10...500 Hz
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g 35 g (PANEL mount)
Emissions CISPR 11 (IEC 61000-6-4):
Class A
ESD immunity IEC 61000-4-2:
6 kV contact discharges 8 kV air discharges
Radiated RF immunity IEC 61000-4-3:
10V/m with 1kH sine-wave 80% AM from 80...2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1kHz sine-wave 80% AM from 2000...2700 MHz
EFT/B immunity IEC 61000-4-4:
± 2kV @ 5 kHz on shielded ports
Surge transient immunity IEC 61000-4-5:
± 2 kV line-earth(CM) on shielded ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1kHz sine-wave 80% AM from 150 kHz...80 Mhz
Operating altitude 2000 m
Cable length, max. 10 m
(1) Includes offset, gain, non-linearity and repeatability error terms.
(2) Repeatability is the ability of the input module to register the same reading in successive measurements for the
same input signal.
68 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 79
Specifications Appendix A
Output Specifications – 2080-OF2
Attribute 2080-OF2
Number of outputs, single
2
ended
Analog normal operating ranges
Voltage: 10V DC Current: 0…20 mA
Resolution, max. 12 bits unipolar
Output count range 0…65535
D/A Conversion Rate (all
2.5 ms
channels), max.
Step Response to 63%
Current Load ln voltage
(1)
5 ms
10 mA
output, max
Resistive load on current
0…500 (includes wire resistance)
output
Load range on voltage output > 1k @ 10V DC
Max. inductive load
0.01 mH
(current outputs)
Max. capacitive load
0.1 µF
(voltage outputs)
Overall Accuracy
(2)
Voltage Terminal: ±1% full scale @ 25 °C Current Terminal: ±1% full scale @ 25 °C
Non-linearity (in percent full
± 0.1%
scale)
Repeatability
(3)
(in percent
± 0.1%
full scale)
Output error over full temperature range,
Voltage: ± 1.5% Current: ± 2.0%
-20…65°C (-4…149°F)
Open and short-circuit
Yes
protection
Output overvoltage protection Yes
Input group to bus isolation No isolation
Channel to channel isolation Non-isolation
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20...65 °C (-4…149 °F)
Temperature, non-operating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat), IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40...85 °C (-40…185 °F)
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5…95% non-condensing
Vibration IEC 60068-2-6 (Test Fc, Operating):
2g @ 10...500 Hz
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 69
Page 80
Appendix A Specifications
Output Specifications – 2080-OF2
Attribute 2080-OF2
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g 35 g (PANEL mount)
Emissions CISPR 11 (IEC 61000-6-4):
Class A
ESD immunity IEC 61000-4-2:
6 kV contact discharges 8 kV air discharges
Radiated RF immunity IEC 61000-4-3:
10V/m with 1kH sine-wave 80% AM from 80...2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1kHz sine-wave 80% AM from 2000...2700 MHz
EFT/B immunity IEC 61000-4-4:
± 2kV @ 5 kHz on shielded ports
Surge transient immunity IEC 61000-4-5:
± 2 kV line-earth(CM) on shielded ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1kHz sine-wave 80% AM from 150 kHz...80 Mhz
Operating altitude 2000 m
Cable length, max. 10 m
(1) Step response is the period of time between when the D/A converter was instructed to go from minimum to full
range until the device is at 63% of full range.
(2) Includes offset, gain, non-linearity and repeatability error terms.
(3) Repeatability is the ability of the output module to reproduce output readings when the same controller value is
applied to it consecutively, under the same conditions and in the same direction.
Certifications – 2080-IF2, 2080-IF4, 2080-OF2
Certification (when product is marked)
(1)
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
CE European Union 2014/30/EU EMC Directive, compliant with:
RCM Australian Radiocommunications Act, compliant with:
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
Value
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
AS/NZS CISPR 11; Industrial Emissions
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declarations of Conformity, Certificates, and other certification details.
70 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 81

Specialty Plug-in Modules

IMPORTANT
Specifications Appendix A
Specifications – 2080-MEMBAK-RTC, 2080-MEMBAK-RTC2
Attribute Value
Resolution READ_RTC() 1 s
Accuracy ± 5 sec/month @ 25 °C
± 9 sec/month@ -20…65 °C
Power off Battery — 3.5 years from date of manufacture @ 25…65 °C, 2.5
years from date of manufacture @ 0 °C
Temperature, operating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat), IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-20...65 °C (-4…149 °F)
Temperature, nonoperating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat), IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40...85 °C (-40…185 °F)
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5…95% non-condensing
Vibration IEC 60068-2-6 (Test Fc, Operating):
2g @ 10...500 Hz
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g 35 g (PANEL mount)
Emissions CISPR 11 (IEC 61000-6-4):
Class A
ESD immunity IEC 61000-4-2:
6 kV contact discharges 8 kV air discharges
Radiated RF immunity IEC 61000-4-3:
10V/m with 1kH sine-wave 80% AM from 80...2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1kHz sine-wave 80% AM from 2000...2700 MHz
Altitude, operating 2000 m
Battery life does not include controller ON time. For example, if the Controller is ON for 16 hours every day for 365 days, if the module starts being used after 1 year of manufacturing, battery life is 8.5 years (1 year initial time + 2.5 years of Off time out of 7.5 years).
Specifications – 2080-TRIMPOT6
Attribute Value
Data range 0…255
Number of trimpot 6
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20...65 °C (-4…149 °F)
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 71
Page 82
Appendix A Specifications
Specifications – 2080-TRIMPOT6
Attribute Value
Temperature, nonoperating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
Temperature, surrounding air, max
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
Vibration IEC 60068-2-6 (Test Fc, Operating):
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Emissions CISPR 11 (IEC 61000-6-4):
ESD immunity IEC 61000-4-2:
Radiated RF immunity IEC 61000-4-3:
Altitude, operating 2000 m
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat), IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40...85 °C (-40…185 °F)
65 °C (149 °F)
5%...95% non-condensing
2g @ 10...500 Hz
25 g
25 g 35 g (PANEL mount)
Class A
6 kV contact discharges 8 kV air discharges
10V/m with 1kH sine-wave 80% AM from 80...2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1kHz sine-wave 80% AM from 2000...2700 MHz
Certifications – 2080-MEMBAK-RTC, 2080-MEMBAK-RTC2, 2080-TRIMPOT6
Certification (when product is marked)
(1)
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
CE European Union 2014/30/EU EMC Directive, compliant with:
RCM Australian Radiocommunications Act, compliant with:
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declarations of Conformity, Certificates, and other certification details.
Value
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
AS/NZS CISPR 11; Industrial Emissions
72 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 83
Specifications Appendix A
General and Environmental Specifications – 2080-TC2, 2080-RTD2
Attribute 2080-RTD2 2080-TC2
Mounting torque 0.2 Nm (1.48 lb-in.)
Terminal screw torque 0.22…0.25 Nm (1.95…2.21 lb-in.)
using a 2.5 mm (0.10 in.) flat-blade screwdriver
Wire size 0.14…1.5 mm
2
(26…16 AWG) solid copper wire or
0.14…1.0 mm2 (26…17 AWG) stranded copper wire rated @ 90 °C (194 °F ) insulation max
Input impedance > 5 M > 300 K
Common mode rejection ratio 100 dB 50/60Hz
Normal mode rejection ratio 70 dB @ 50/60 Hz
Resolution 14-bit
CJC error ±1.2 °C @ 25 °C (77 °F)
Accuracy ±1.0 °C for TC and RTD @ 25 °C (77 °F)
Channels 2, non-isolated
RTD types supported 100 Platinum 385
— 200 Platinum 385 500 Platinum 385 1000 Platinum 385 100 Platinum 392 200 Platinum 392, 500 Platinum 392 1000 Platinum 392 10 Copper 427 120 Nickel 672 604 Nickel-Iron 518
Thermocouple types
J, K, N, T, E, R, S, B
supported
Open circuit detection time 8…1212 ms 8…1515 ms
Power consumption 3.3 V, 40 mA
Temperature, surrounding air,
65 °C (149 °F)
max.
Temperature, operating IEC60068-2-1 (Test Ad, Operating Cold),
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20...65 °C (-4…149 °F)
Temperature, nonoperating IEC60068-2-1 (Test Ad, Operating Cold),
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-40...85 °C (-40…185 °F)
Vibration IEC 60068-2-6 (Test Fc, Operating):
2g @ 10...500 Hz
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g 35 g (PANEL mount)
Emissions CISPR 11 (IEC 61000-6-4):
Class A
ESD immunity IEC 61000-4-2:
6 kV contact discharges 8 kV air discharges
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 73
Page 84
Appendix A Specifications
General and Environmental Specifications – 2080-TC2, 2080-RTD2
Attribute 2080-RTD2 2080-TC2
Radiated RF immunity IEC 61000-4-3:
10V/m with 1kH sine-wave 80% AM from 80...2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1kHz sine-wave 80% AM from 2000...2700 MHz
EFT/B immunity IEC 61000-4-4:
± 2kV @ 5 kHz on shielded ports
Surge transient immunity IEC 61000-4-5:
± 2 kV line-earth(CM) on shielded ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1kHz sine-wave 80% AM from 150 kHz...80 Mhz
North American temp code T4
Certifications – 2080-TC2, 2080-RTD2
Certification (when product is marked)
(1)
Value
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
CE European Union 2014/30/EU EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
KC Korean Registration of Broadcasting and Communications
Equipment, compliant with: Article 58-2 of Radio Waves Act, Clause 3
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declarations of Conformity, Certificates, and other certification details.
General Specifications – 2080-MOT-HSC
Attribute Value
Dimensions, HxWxD, approx. 62 x 31.5 x 20 mm (2.44 x 1.24 x 0.79 in.)
Terminal screw torque 0.22…0.25 Nm (1.95…2.21 lb-in.)
using a 2.5 mm (0.10 in.) flat-blade screwdriver
Bus current draw 60 mA @ 3.3V DC
Recommended cable Individually shielded, twisted-pair cable (or the type recommended
by the encoder or sensor manufacturer)
74 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 85
Specifications Appendix A
Min Max
Solid 0.14 mm
2
(26 AWG)
1.5 mm2 (16 AWG)
rated @ 90 °C (194 °F) insulation max
Stranded 0.14 mm2
(26 AWG)
1.0 mm2 (18 AWG)
Input A
Input B
Phase separation
General Specifications – 2080-MOT-HSC
Attribute Value
Wire size
Enclosure type rating Meets IP20
Isolation voltage Input module: 50V (continuous), Basic Insulation Type, Inputs/
Wiring Category
(1)
North American Temp Code T4
(1) Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring
and Grounding Guidelines, publication 1770-4.1
Outputs to Backplane Type tested for 60s @ 720V DC, Inputs/Outputs to Backplane
2 – on signal ports
.
Input Specifications – 2080-MOT-HSC
Attribute Value
Number of inputs 1 Quadrature (ABZ) differential input
Maximum count 48 bits
Input voltage range 0…30V DC
On state voltage range 2.6…30V DC
On-state current, min 2.0 mA
Off-state voltage, max 1.0V DC
Off-state leakage current, max 1.5 mA
Input current range 2.0…9.0 mA
Input impedance, nom 3580
Pulse width, min 2 µs
Phase separation, min 500 ns
Input frequency, max 250 kHz (50% duty)
(1) Phase separation is the recognition of phase time of A input and B input.
(1)
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 75
Page 86
Appendix A Specifications
-20
-10 0
10
20
30 40 50 60
70
0
5
10
15
20
25
30
35
Volts (DC)
Ambient Temperature (°C)
Voltage Derating Based on Temperature
26.4V DC @ 65 °C
Volts (DC)
Ambient Temperature (°C)
Voltage Derating Based on Temperature
26.4V DC @ 65 °C
Output Specifications – 2080-MOT-HSC
Attribute Value
Number of outputs 16 (1 physical output; 15 virtual)
Output voltage range 5…30V DC
Output on-state current, max 0.5 A
Output on-state current, min 1 mA
On-state voltage drop, max 0.5V DC
Off-state leakage current, max 0.5 mA
Turn ON time, max 2 ms
Turn OFF time, max 2 ms
Reverse polarity protection None
Temperature Derating
Maximum input voltage – 24V DC operation
Maximum output voltage – 24V DC operation
35
30
25
20
15
10
5
0
-20
-10 0
76 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
10
30 40 50 60
20
70
Page 87
Maximum output currrent per point – 5V DC operation
Current per points (A)
Ambient Temperature (°C)
Current Derating Based on Temperature
Current per points (A)
Ambient temperature (°C)
Current derating based on temperature
1.5
1
0.5
Specifications Appendix A
0
-20
-10 0
10
30 40 50 60
20
70
Maximum output current per point – 24V DC operation
1.5
1
0.5
0
-20
-10 0
10
30 40 50 60
20
70
Environmental Specifications – 2080-MOT-HSC
Attribute Value
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
Temperature, nonoperating IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
Temperature, surrounding air, max
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
Vibration IEC 60068-2-6 (Test Fc, Operating):
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Emissions CISPR 11 (IEC 61000-6-4):
ESD immunity IEC 61000-4-2:
IEC 60068-2-2 (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20…65 °C (-4…149 °F)
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat), IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40…85 °C (-40…185 °F)
65 °C (149 °F)
5…95% noncondensing
2 g @ 10…500 Hz
25 g
25 g 35 g (PANEL mount)
Class A
6 kV contact discharges 8 kV air discharges
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 77
Page 88
Appendix A Specifications
Environmental Specifications – 2080-MOT-HSC
Attribute Value
Radiated RF immunity IEC 61000-4-3:
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
EFT/B immunity IEC 61000-4-4:
±2 kV @ 5 kHz on signal ports
Surge transient immunity IEC 61000-4-5:
±2 kV line-earth(CM) on shielded ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
Certifications – 2080-MOT-HSC
Certification (when product is marked)
(1)
Value
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
CE European Union 2014/30/EU EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
KC Korean Registration of Broadcasting and Communications
Equipment, compliant with: Article 58-2 of Radio Waves Act, Clause 3
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declarations of Conformity, Certificates, and other certification details.
78 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 89
Communication Plug-in
Mounting torque 0.2 Nm
Mounting torque 0.3 Nm
Mounting torque:
0.5…0.6 Nm
46209
Modules
Specifications Appendix A
Specifications – 2080-DNET20
Attribute Value
Screw torque See Torque Specifications for the 2080-DNET20 Plug-in Module on
Dimensions, HxWxD 62 x 31.5 x 20 mm (2.44 x 1.24 x 0.78 in.)
Weight 35 g
DeviceNet communication rate, max
Number of nodes, max 20 nodes for I/O operation
Network Protocol I/O Slave Messaging: Poll Command
DeviceNet Status indicators Module status – red/green
Enclosure type rating Meets IP20
Backplane power consumption 50 mA @ 24V DC
DeviceNet current 24V DC, 300 mA Class 2
Power dissipation, max 1.44 W
Isolation voltage 50V (continuous)
Wire size 0.25... 2.5 mm
Wire category 1 – on power ports
North American temp code T4
Preferred power supply 1606-XLSDNET4
page 79.
125 Kbps – 420 m (1378 ft.) 250 Kbps – 200 m (656 ft.) 500 Kbps – 75 m (246 ft.)
Network status – red/green
Type tested for 60 s @ 500V AC
2
@ 75 °C (167 °F ), or greater, 1.2 mm (3/64 in.) insulation max
(24...14 AWG) solid or stranded copper wire rated
Torque Specifications for the 2080-DNET20 Plug-in Module
ATTENTION: To comply with CE Low Voltage Directive (LVD), this
equipment and all connected I/O must be powered from a source compliant with the following: Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 79
Page 90
Appendix A Specifications
ATTENTION: To comply with UL restrictions, this equipment must be
powered from a source compliant with the following: Class 2 or Limited Voltage/Current.
Environmental Specifications – 2080-DNET20
Attribute Value
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
Temperature, surrounding air, max.
Temperature, nonoperating IEC60068-2-1 (Test Ad, Operating Cold),
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
Vibration IEC 60068-2-6 (Test Fc, Operating):
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Emissions CISPR 11 (IEC 61000-6-4):
ESD Immunity IEC 61000-4-2:
Radiated RF immunity IEC 61000-4-3:
EFT/B immunity IEC 61000-4-4:
Surge transient immunity IEC 61000-4-5:
Conducted RF immunity IEC 61000-4-6:
IEC 60068-2-2 (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20…65 °C (-4…149 °F)
65 °C (149 °F)
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-40...85 °C (-40…185 °F)
5…95% noncondensing
2g @ 10...500 Hz
25 g
25 g 35 g (PANEL mount)
Class A
6 kV contact discharges 8 kV air discharges
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
±2 kV @ 5 kHz on communication ports
±2 kV line-earth(CM) on communication ports
10V rms with 1 kHz sine-wave 80% AM from 150 kHz…80 MHz
80 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 91
Min Max
Solid 0.14 mm
2
(26 AWG)
1.5 mm
2
(16 AWG)
rated @ 90 °C (194 °F ) insulation max
Stranded 0.14 mm
2
(26 AWG)
1.0 mm
2
(18 AWG)
Certifications – 2080-DNET20
Specifications Appendix A
Certification (when product is
(1)
marked)
Valu e
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
CE European Union 2014/30/EU EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
KC Korean Registration of Broadcasting and Communications
Equipment, compliant with: Article 58-2 of Radio Waves Act, Clause 3
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
DeviceNet ODVA conformance tested to DeviceNet specifications.
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declarations of Conformity, Certificates, and other certification details.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 81
General and Environmental Specifications – 2080-SERIALISOL
Attribute Value
Mounting torque 0.2 Nm (1.48 lb-in)
Terminal screw torque 0.22…0.25 Nm (1.95…2.21 lb-in)
Wire size
Isolated voltage 500V AC
Temperature, operating IEC60068-2-1 (Test Ad, Operating Cold),
Temperature, surrounding air, max.
Temperature, non-operating
Vibration IEC 60068-2-6 (Test Fc, Operating):
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
(using a 2.5 mm (0.10 in.) flat-blade screwdriver)
IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20...65 °C (-4…149 °F)
65 °C (149 °F)
IEC60068-2-1 (Test Ad, Operating Cold), IEC60068-2-2, (Test Bd, Operating Dry Heat), IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-40...85 °C (-40…185 °F)
2g @ 10...500 Hz
25 g
Page 92
Appendix A Specifications
General and Environmental Specifications – 2080-SERIALISOL
Attribute Value
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
25 g 35 g (PANEL mount)
Emissions CISPR 11 (IEC 61000-6-4):
Class A
ESD immunity IEC 61000-4-2:
6 kV contact discharges 8 kV air discharges
Radiated RF immunity IEC 61000-4-3:
10V/m with 1kH sine-wave 80% AM from 80...2000 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM @ 1890 MHz 10V/m with 1kHz sine-wave 80% AM from 2000...2700 MHz
EFT/B immunity IEC 61000-4-4:
± 2 kV @ 5 kHz on communication ports
Surge transient immunity IEC 61000-4-5:
± 2 kV line-earth(CM) on communication ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1kHz sine-wave 80% AM from 150 kHz...80 Mhz
North American temp code T4
Certifications – 2080-SERIALISOL
Certification (when product is marked)
(1)
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada.
CE European Union 2014/30/EU EMC Directive, compliant with:
RCM Australian Radiocommunications Act, compliant with:
EAC Russian Customs Union TR CU 020/2011 EMC Technical Regulation
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ Declarations
of Conformity, Certificates, and other certification details.
Value
See UL File E322657.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations,
certified for U.S. and Canada. See UL File E334470.
EN 61326-1; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
AS/NZS CISPR 11; Industrial Emissions
82 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 93
Quickstart
TIP
This chapter provides the following quickstarts.
Topic Page
Add and Configure Plug-ins in Connected Components Workbench 83
Browse Your 2080-DNET20 Plug-in Using RSLinx 85
Flash Upgrade Your 2080-DNET20 Plug-in Firmware 88
Quickstart Project for 2080-DNET20 Plug-in 92
Quickstart Projects for 2080-MOT-HSC Plug-in 97
Appendix
B

Add and Configure Plug-ins in Connected Components Workbench

This section shows you an example of how to configure the plug-ins through the Connected Components Workbench software.
For more information about using Connected Components Workbench, you can check out the Connected Components Workbench Online Help (it comes with the software).
The following steps show a Micro820 controller.
1. Launch the Connected Components Workbench software and open your Micro800 project. On the Project Organizer pane, right-click the project name and select Open.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 83
Page 94
Appendix B Quickstart
The Controller Properties page appears.
2. To add a Micro800 plug-in, you can do any of the following:
Right-click the plug-in slot you would like to configure and choose the plug-in, as shown below.
84 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 95
Quickstart Appendix B
IMPORTANT
Right-click the plug-in slot in the Controller Properties tree and choose the plug-in you would like to add.
.
The device configuration window should show the added plug-in modules:

Browse Your 2080-DNET20 Plug-in Using RSLinx

There are two methods you can use to browse for your 2080-DNET20 plug-in using RSLinx. The first method is browsing directly to the plug-in through the DeviceNet network. The second method is browsing through a Micro820/ Micro830/Micro850 controller using the pass through feature. This allows you to upgrade the firmware of the plug-in.
To use the controller pass through feature, the following firmware revisions are required:
Micro820/Micro830/Micro850 controller firmware revision 8.011 or
higher.
2080-DNET20 plug-in firmware revision 2.011 or higher.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 85
Page 96
Appendix B Quickstart
Right-click on the plug-in and select Properties to view the Device properties
Browse Using the DeviceNet Network
From the computer, the 2080-DNET20 plug-in can be browsed through the DeviceNet network. This requires an additional device to connect the computer to the DeviceNet network. For example, you can use the 1788-EN2DN or 1784-U2DN devices. For instructions on connecting the plug-in to the DeviceNet network, see Setup and Wiring
Browsing the 2080-DNET20 plug-in through the DeviceNet network
on page93.
86 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 97
Quickstart Appendix B
IMPORTANT
Browse Using the Micro800 Pass Through
To use the controller pass through feature, the following firmware revisions are required:
Micro820/Micro830/Micro850 controller firmware revision 8.011 or
higher.
2080-DNET20 plug-in firmware revision 2.011 or higher.
Browsing the 2080-DNET20 plug-in from the controller backplane through EtherNet/IP.
Browsing the 2080-DNET20 plug-in from the controller backplane through USB.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 87
Page 98
Appendix B Quickstart
Browsing the 2080-DNET20 plug-in from the controller backplane through Serial DF1.

Flash Upgrade Your 2080-DNET20 Plug-in Firmware

This quick start will show you how to flash update the firmware in a 2080-DNET20 plug-in using ControlFLASH. ControlFLASH is installed or updated when Connected Components Workbench software is installed on your computer. It is recommended that the controller is in Program mode and the plug-in is in Idle mode when performing the upgrade.
1. Check the firmware revision of the plug-in. To do this, check the Device Properties of the plug-in RSLinx.
88 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Page 99
Quickstart Appendix B
2. Launch ControlFLASH and click Next.
3. In the Catalog Number dialog, select the 2080-DNET20 plug-in and click
Next.
Rockwell Automation Publication 2080-UM004D-EN-E - March 2018 89
Page 100
Appendix B Quickstart
IMPORTANT
4. The Connection Browser dialog appears, select the 2080-DNET20 plug­in and click OK.
To upgrade from firmware revision 1.012 to 2.011, the DeviceNet network should be used. From revision 2.011 onwards, you can upgrade the firmware using the controller pass through feature.
5. Select the firmware revision to flash and click Next.
90 Rockwell Automation Publication 2080-UM004D-EN-E - March 2018
Loading...