Installation Instructions
E300 / E200 Operator Stations
(Cat 193-EOS-SCS; 193-EOS-SDS)
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Follow NFPA 70E requirements. Install in suitable enclosure. Keep free from contaminants.
Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by suitably trained personnel in accordance with applicable code of practice. In case of
malfunction or damage, no attempts at repair should be made. The product should be returned to the manufacturer for repair. Do not dismantle the product.
Additional Resources:
1) Go to http://www.literature.rockwellautomation.com; 2) Go to Search. Type in publication number: 193-UM015
Features
Power LED
Trip / Warn LED
Power LED
Trip / Warn LED
Escape
Up
Select
Start Forward / Speed 1
Start Reverse / Speed 2
Local / Remote
Installation
1
1
LOCAL
REMOTE
Stop
LOCAL
REMOTE
Reset
0
RESET
Start Forward / Speed 1
Start Reverse / Speed 2
Local / Remote
Stop
LOCAL
REMOTE
ESC
Reset
SELECT
0
RESET
Enter
Down
193-EOS-SCS 193-EOS-SDS (Requires control module rmware v3.000 or higher)
2
2
1.7 N.m
(15 lb-in)
ESC
SELECT
0
RESET
800F-AW2
3
For use on a at surface of a Type 4X Enclosure
1
Click
2
Copy Cat (read and write complete device congurations
to and from the operator station)
Power LED
ESC
SELECT
LOCAL
REMOTE
0
RESET
Local / Remote
Stop
Read
1) Press for 3 seconds (Local / Remote + Stop)
2) Power LED blinks Red / Green
3) Blinking Green = Successful
4) Blinking Red = Unsuccessful
Power LED
ESC
SELECT
LOCAL
REMOTE
0
RESET
Stop
Reset
Write
1) Press for 3 seconds (Stop + Reset)
2) Power LED blinks Red / Green
3) Blinking Green = Successful
4) Blinking Red = Unsuccessful
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Diagnostics Specications
Power LED
Blinking Green
Solid Green
Solid Red
Blinking Red
Blinking Red / Green
Trip / Warn LED
Blinking Red
Blinking Yellow
Overload
Phase Loss
Ground Fault
Stall
Jam
Underload
Current Imbalance
L1 Under Current
L2 Under Current
Current
L3 Under Current
L1 Over Current
L2 Over Current
L3 Over Current
L1 Line Loss
L2 Line Loss
L3 Line Loss
Under Volt L-L
Over Volt L-L
Voltage Unbalance
Phase Rotation
Under Frequency
VoltagePowerControlAnalog
Over Frequency
Under Real Pwr
Over Real Pwr
Under Con kVAR
Over Con kVAR
Under Gen kVAR
Over Gen kVAR
Under Power kVA
Over Power kVA
Under PF Lagging
Over PF Lagging
Under PF Leading
Over PF Leading
Test Trip
PTC
DLX
Operator Station Trip
Remote Trip
Start Inhibit
Hardware Fault
Invalid Conguration
Option Match
Feedback Timeout
Expansion Bus
Number of Starts
Operating Hours
Non-Volatile Memory 3 14
Test Mode Trip 3 15
Analog Input11
Analog Input12
Analog Input13
Analog Input21
Analog Input22
Analog Input23
Analog Input31
Analog Input32
Analog Input33
Analog Input41
Analog Input42
Analog Input43
Device Ready
Device Active (Current Detected)
Operator Station Error
Communication Error
Copy Cat in Progress
Trip
Warning
Long Blink Pattern Short Blink Pattern
0
0
0
0
0
0
0
08
0
0
0
0
0
0
0
016
1
1
1
1
1
1
2
2
2
2
2
2
2
28
2
2
2
2
3
3
3
3
3
3
3
38
3
3
3
3
313
4
4
4
4
4
4
4
48
4
4
4
4
IP Rating: IP65
UL Type: Type 4X
Ambient: 55º C Max.
1
2
3
4
5
6
7
9
10
11
12
13
14
15
1
2
3
4
5
6
1
2
3
4
5
6
7
9
10
11
12
1
2
3
4
5
6
7
9
10
11
12
1
2
3
4
5
6
7
9
10
11
12
Publication 193-IN061D-EN-P - September 2014
Copyright © 2014 Rockwell Automation, Inc. All Rights Reserved. Printed in Malaysia.
DIR 10000518537 (Version 03)
Loading...