Page 1
Installation Instructions
MicroLogix 1762-IQ32T DC Input Module
Catalog Number 1762-IQ32T
Table of Contents
Topic Page
Important User Information 2
North American Hazardous Location Approval 4
Additional Resources 5
Overview 6
Module Description 7
Mount the Module 8
Field Wiring Connections 11
Wiring Options for the I/O Module 13
Labeling for the 1492 Interface Module 14
Assemble the Wire Contacts 15
Specifications 17
Page 2
2 MicroLogix 1762-IQ32T DC Input Module
WARNING
IMPORTANT
ATTENTION
SHOCK HAZARD
BURN HAZARD
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment.
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication
SGI-1.1
available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com
equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot
assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
) describes some important differences between solid state
Publication 1762-IN019B-EN-P - June 2013
Identifies information that is critical for successful application and understanding of
the product.
Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you identify a hazard,
avoid a hazard and recognize the consequences.
Labels may be on or inside the equipment (for example, drive or motor) to alert people
that dangerous voltage may be present.
Labels may be on or inside the equipment (for example, drive or motor) to alert people
that surfaces may reach dangerous temperatures.
Page 3
Environment and Enclosure
ATTENTION
ATTENTION
This equipment is intended for use in a Pollution Degree 2 industrial
environment, in overvoltage Category II applications (as defined in IEC 60664-1),
at altitudes up to 2000 m (6562 ft) without derating.This equipment is
considered Group 1, Class A industrial equipment according to IEC/CISPR 11.
Without appropriate precautions, there may be difficulties with electromagnetic
compatibility in residential and other environments due to conducted and
radiated disturbances.
This equipment is supplied as open-type equipment. It must be mounted within
an enclosure that is suitably designed for those specific environmental
conditions that will be present and appropriately designed to prevent personal
injury resulting from accessibility to live parts. The enclosure must have suitable
flame-retardant properties to prevent or minimize the spread of flame,
complying with a flame spread rating of 5VA, V2, V1, V0 (or equivalent) if
non-metallic. The interior of the enclosure must be accessible only by the use of
a tool. Subsequent sections of this publication may contain additional
information regarding specific enclosure type ratings that are required to comply
with certain product safety certifications.
In addition to this publication, see:
• Industrial Automation Wiring and Grounding Guidelines, for additional
installation requirements, Allen-Bradley publication 1770-4.1
• NEMA Standards 250 and IEC 60529, as applicable, for explanations of
the degrees of protection provided by different types of enclosure.
MicroLogix 1762-IQ32T DC Input Module 3
.
Preventing Electrostatic Discharge
This equipment is sensitive to electrostatic discharge, which can cause internal
damage and affect normal operation. Follow these guidelines when you handle
this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.
Publication 1762-IN019B-EN-P - June 2013
Page 4
4 MicroLogix 1762-IQ32T DC Input Module
WARNING
AVERTISSEMENT
North American Hazardous Location Approval
The following modules are North American Hazardous Location approved: 1762-IQ32T
The following information applies when
operating this equipment in hazardous
locations:
Products marked "CL I, DIV 2, GP A, B, C, D" are
suitable for use in Class I Division 2 Groups A, B, C,
D, Hazardous Locations and nonhazardous
locations only. Each product is supplied with
markings on the rating nameplate indicating the
hazardous location temperature code. When
combining products within a system, the most
adverse temperature code (lowest "T" number) may
be used to help determine the overall temperature
code of the system. Combinations of equipment in
your system are subject to investigation by the
local Authority Having Jurisdiction at the time of
installation.
EXPLOSION HAZARD
• Do not disconnect equipment
unless power has been removed or
the area is known to be
nonhazardous.
• Do not disconnect connections to
this equipment unless power has
been removed or the area is known
to be nonhazardous. Secure any
external connections that mate to
this equipment by using screws,
sliding latches, threaded
connectors, or other means
provided with this product.
• Substitution of components may
impair suitability for Class I,
Division 2.
• If this product contains batteries ,
they must only be changed in an
area known to be nonhazardous.
• All wiring must comply with N.E.C.
article 501-4(b).
• The interior of the enclosure must
be accessible only by the use of a
tool.
• For applicable equipment (relay
modules, etc.), exposure to some
chemicals may degrade the sealing
properties of materials used in the
following devices: Relays, Epoxy. It
is recommended that the User
periodically inspect these devices
for any degradation of properties
and replace the module if
degradation is found.
Informations sur l’utilisation de cet
équipement en environnements dangereux:
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne
conviennent qu'à une utilisation en environnements de
Classe I Division 2 Groupes A, B, C, D dangereux et non
dangereux. Chaque produit est livré avec des
marquages sur sa plaque d'identification qui indiquent
le code de température pour les environnements
dangereux. Lorsque plusieurs produits sont combinés
dans un système, le code de température le plus
défavorable (code de température le plus faible) peut
être utilisé pour déterminer le code de température
global du système. Les combinaisons d'équipements
dans le système sont sujettes à inspection par les
autorités locales qualifiées au moment de l'installation.
RISQUE D’EXPLOSION
• Couper le courant ou s’assurer que
l’environnement est cl assé non
dangereux avant de débrancher
l'équipement.
• Couper le courant ou s'assurer que
l'environnement est classé non
dangereux avant de débrancher les
connecteurs. Fixer tous les connecteurs
externes reliés à cet équipement à
l'aide de vis, loquets coulissants,
connecteurs filetés ou autres moye ns
fournis avec ce produit.
• La substitution de composants peut
rendre cet équipement inadapté à u ne
utilisation en environnement de Classe
I, Division 2.
• S’assurer que l’environnement est
classé non dangereux avant de changer
les piles.
Publication 1762-IN019B-EN-P - June 2013
Page 5
MicroLogix 1762-IQ32T DC Input Module 5
Additional Resources
Resource Description
MicroLogix 1100 Programmable Controllers User
Manual, publication 1763-UM001
MicroLogix 1200 Programmable Controllers User
Manual, publication 1762-UM001
MicroLogix 1400 Programmable Controllers User
Manual, publication 1766-UM001
MicroLogix 1100 Programmable Controllers
Installation Instructions, publication 1763-IN001
MicroLogix 1200 Programmable Controllers
Installation Instructions, publication 1762-IN006
MicroLogix 1400 Programmable Controllers
Installation Instructions, publication 1766-IN001
Industrial Automation Wiring and Grounding
Guidelines, publication 1770-4.1
.
.
.
.
A more detailed description of how to install and use
your MicroLogix 1100 programmable controller and
expansion I/O system.
A more detailed description of how to install and use
your MicroLogix 1200 programmable controller and
expansion I/O system.
A more detailed description of how to install and use
your MicroLogix 1400 programmable controller and
expansion I/O system.
Information on installing and using the
.
MicroLogix 1100 programmable controller.
Information on installing and using the
.
MicroLogix 1200 programmable controller.
Information on installing and using the
.
MicroLogix 1400 programmable controller.
More information on proper wiring and grounding
techniques.
If you would like a manual, you can:
• download a free electronic version from the Internet:
http://literature.rockwellautomation.com
• purchase a printed manual by contacting your local Allen-Bradley distributor or
Rockwell Automation representative
Publication 1762-IN019B-EN-P - June 2013
Page 6
6 MicroLogix 1762-IQ32T DC Input Module
ATTENTION
ATTENTION
Debris strip
44909
Overview
The 1762 input module is suitable for use in an industrial environment when installed in
accordance with these instructions. Specifically, this equipment is intended for use in clean, dry
environments (Pollution degree 2
(3)
(IEC 60664-1)
.
Install your module using these installation instructions.
1762 Input Module
(1)
) and to circuits not exceeding Over Voltage Category II
(2)
(1)
(2)
(3)
Publication 1762-IN019B-EN-P - June 2013
Do not remove the protective debris strip until after the module and all other
equipment in the panel near the module are mounted and wiring is complete.
Once wiring is complete, remove protective debris strip. Failure to remove strip
before operating can cause overheating.
Electrostatic discharge can damage semiconductor devices inside the module.
Do not touch the connector pins or other sensitive areas.
Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a
temporary conductivity caused by condensation shall be expected.
Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are
controlled and do not exceed the impulse voltage capability of the product’s insulation.
Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.
Page 7
MicroLogix 1762-IQ32T DC Input Module 7
ATTENTION
4491144910
Left side view
Front view
1a
1b
2
4
5
6
8
8
3
7
9
This equipment is sensitive to electrostatic discharge (ESD).
Follow ESD prevention guidelines when handling this equipment.
Module Description
Description Description
1a Upper panel mounting tab 5 Bus connector cover
1b Lower panel mounting tab 6 Bus connector with male pins
2 Pull loop 7 DIN rail latch
3 MIL-C-083503 connector 8 Flat ribbon cable with bus connector (female pins)
4 Module door with terminalidentification label 9 I/O Diagnostic LEDs
To comply with UL restrictions, this equipment must be powered from a source
compliant with Class 2 or Limited Voltage/Current.
Publication 1762-IN019B-EN-P - June 2013
Page 8
8 MicroLogix 1762-IQ32T DC Input Module
ATTENTION
44912
Measurements do not include mounting feet or DIN rail latches.
90 mm
(3.5 in.)
87 mm
(3.43 in.)
40.4 mm (1.59 in.)
Mount the Module
General Considerations
Most applications require installation in an industrial enclosure to reduce the effects of electrical
interference and environmental exposure. Locate your controller as far as possible from power
lines, load lines, and other sources of electrical noise such as hard-contact switches, relays, and
AC motor drives. For more information on proper grounding guidelines, see the Industrial
Automation Wiring and Grounding Guidelines, publication 1770-4.1
This product is intended to be mounted to a well-grounded mounting surface
such as a metal panel. Additional grounding connections from the power
supply's mounting tabs or DIN rail (if used) are not required unless the mounting
surface cannot be grounded. Refer to Industrial Automation Wiring and
Grounding Guidelines, Allen-Bradley publication 1770-4.1
information.
Mounting Dimensions
.
, for additional
Publication 1762-IN019B-EN-P - June 2013
Page 9
MicroLogix 1762-IQ32T DC Input Module 9
TIP
Top
Bottom
Side
44913
Side
44566
End anchor
End anchor
Module Spacing
Maintain spacing from objects such as enclosure walls, wireways and adjacent equipment. Allow
50.8 mm (2 in.) of space on all sides for adequate ventilation, as shown:
MicroLogix
1100/1200/1400
1762 I/O
1762 I/O
1762 I/O
DIN Rail Mounting
The module can be mounted using the following DIN rails: 35 x 7.5 mm (EN 50 022 - 35 x 7.5)
or 35 x 15 mm (EN 50 022 - 35 x 15).
Before mounting the module on a DIN rail, close the DIN rail latch. Press the DIN rail
mounting area of the module against the DIN rail. The latch will momentarily open and lock
into place.
Use DIN rail end anchors (Allen-Bradley part number 1492-EA35 or 1492-EAH35) for
vibration or shock environments.
For environments with greater vibration and shock concerns, use the panel
mounting method described below, instead of DIN rail mounting.
Publication 1762-IN019B-EN-P - June 2013
Page 10
10 MicroLogix 1762-IQ32T DC Input Module
TIP
90
(3.54)
100.06
(3.939)
40.4
(1.59)
40.4
(1.59)
14.2
(0.568)
MicroLogix
1100/1200/1400
1762 I/O
1762 I/O
1762 I/O
95 (3.74)
44914
For more than two I/O modules: measure (number of modules - 1) x 40 mm (1.59 in.)
NOTE: All dimensions are in mm (in.). Hole spacing tolerance: ±0.4 mm (0.016 in.).
44569
Bus connector covers
1762 expansion
bus connector
cover
Panel Mounting
Use the dimensional template shown below to mount the module. The preferred mounting
method is to use two M4 (#8) panhead screws per module. M3.5 (#6) panhead screws may also
be used, but a washer may be needed to ensure a good mechanical contact. Mounting screws are
required on every module.
System Assembly
The expansion I/O module is attached to the controller or another I/O module by means of a
flat ribbon cable after mounting as shown below.
Publication 1762-IN019B-EN-P - June 2013
Use the pull loop on the connector to disconnect modules. Do not pull on the
ribbon cable.
Page 11
MicroLogix 1762-IQ32T DC Input Module 11
WARNING
ATTENTION
WARNING
Field Wiring Connections
Grounding the Module
In solid-state control systems, grounding and wire routing helps limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the ground screw of the
controller to the ground bus prior to connecting any devices. Use AWG #14 wire. For
AC-powered controllers, this connection must be made for safety purposes.
You must also provide an acceptable grounding path for each device in your application. For
more information on proper grounding guidelines, refer to the Industrial Automation Wiring
and Grounding Guidelines, publication 1770-4.1
EXPLOSION HAZARD
• In Class I, Division 2 applications, the bus connector must be fully seated and
the bus connector cover must be snapped in place.
• In Class I, Division 2 applications, all modules must be mounted in direct
contact with each other as shown on page 10. If DIN rail mounting is used, an
end anchor must be installed ahead of the controller and after the last 1762
I/O module.
.
To comply with the CE Low Voltage Directive (LVD), all connected I/O must be
powered from a source compliant with the Safety Extra Low Voltage (SELV) or
Protected Extra Low Voltage (PELV).
If you connect or disconnect wiring while the field-side power is on, an electrical
arc can occur. This could cause an explosion in hazardous location installations.
Be sure that power is removed or the area is nonhazardous before proceeding.
Publication 1762-IN019B-EN-P - June 2013
Page 12
12 MicroLogix 1762-IQ32T DC Input Module
ATTENTION
44920
44923
Input Wiring
Basic wiring of input devices to the 1762-IQ32T is shown below.
Basic Input Wiring to the 1762-IQ32T Module
Simplified Input Circuit Diagram
A write-on label is provided with the module. Mark the identification of each terminal with
permanent ink, and slide the label back into the door.
Publication 1762-IN019B-EN-P - June 2013
VCC
ASIC
Signal
GND
Sinking/Sourcing Inputs - Sourcing/sinking describes the current flow between
the I/O module and the field device. Sourcing I/O circuits supply (source) current
to sinking field devices. Sinking I/O circuits are driven by a current sourcing field
device. Field devices connected to the negative side (DC Common) of the field
power supply are sinking field devices. Field devices connected to the positive
side (+V) of the field supply are sourcing field devices.
Page 13
MicroLogix 1762-IQ32T DC Input Module 13
TIP
ATTENTION
Keyed female
connector (1746-N3)
Included with 32-point
input modules
44924
32-point input module
Keyed male
MIL-C-083503
connector
Panel lights, buttons,
sensors
Contact pins provided with
female connector can
accept 22...26 AWG wires.
User terminal connector
Wiring Options for the I/O Module
Included with your 32-point input module is a keyed 40-pin female connector and crimp type
pins. These components allow you to wire I/O devices to the module using a 40-conductor cable
or individual wires. Refer to Assemble the Wire Contacts on page 15 for more information on
connector/pin assembly instructions.
When assembled, align the female connector over the module’s male header using the keying slot
as a guide. Firmly lock them together with the upper and lower retaining arms.
Wire the 1746-N3 Connector
If you decide to build your cable using another 1746-N3 to terminate the cable at the
1492 Interface Module end, wire it in the following manner: Pin 1 to Pin 1, Pin 2 to
Pin 2, Pin 3 to Pin 3, and so on.
Maximum user cable length is dependent on how much voltage drop (current x
(ohms/ft.) x (feet)) the user’s system can tolerate. The user’s system should take
into account the minimum turn-on voltage required by external loads connected
to the 32-point output module, the minimum turn-on voltage required by the
32-point input module and all of the voltage drops associated with wiring to and
from the load, sensors, terminal connector, power sources and the module itself.
Publication 1762-IN019B-EN-P - June 2013
Page 14
14 MicroLogix 1762-IQ32T DC Input Module
Labeling for the 1492 Interface Module
Several different stick-on label sets are provided on a single card with 1492 Interface Modules.
Each label set is identified with an I/O module catalog number and words upper and lower to
identify which terminal strip the label should be affixed to.
The following table identifies the 1762-IQ32T 32-point labels and their location on the
interface module. Peel off the appropriate label and apply it to the interface module.
Terminal Connector Labels
Bottom Terminal Connector Top Terminal Connector
COM 1 COM 3
COM 1 COM 3
IN 00 IN 16
IN 01 IN 17
IN 02 IN 18
IN 03 IN 19
IN 04 IN 20
IN 05 IN 21
IN 06 IN 22
IN 07 IN 23
IN 08 IN 24
IN 09 IN 25
IN 10 IN 26
IN 11 IN 27
IN 12 IN 28
IN 13 IN 29
IN 14 IN 30
IN 15 IN 31
COM 2 COM 4
COM 2 COM 4
Publication 1762-IN019B-EN-P - June 2013
Page 15
MicroLogix 1762-IQ32T DC Input Module 15
ATTENTION
44916
Wire stop
Wire barrel
Tang
Stripped wire
44921
Insulation barrel
Stripped wire
Tang
44922
Terminal connector
Terminal sockets
Wire contact
Assemble the Wire Contacts
1. Strip the wire insulation to expose 4 mm (5/32 in.) of wire. Crimp pins can accept
22...26 AWG wire.
Be careful when stripping wires. Wire fragments that fall into the module could
cause damage. Once wiring is complete, be sure the module is free of all metal
fragments before removing the protective debris strip. Failure to remove the
strip before operating can cause overheating.
2. Insert the wire into the crimp pin as far as the wire stop.
4 mm
(5/32 in.)
3. Crimp the wire barrel around the wire using small needle nose pliers.
4. Crimp the insulation barrel around the wire insulation using small needle nose pliers.
5. Solder wire and wire barrel together using lead-free solder and soldering pencil.
6. Insert the assembled wire contact into the terminal socket. Push the wire contact in until
the tang latches. Make sure the tang is properly latched by lightly pulling on the wire.
Publication 1762-IN019B-EN-P - June 2013
Page 16
16 MicroLogix 1762-IQ32T DC Input Module
I1:x.0/0
Slot number
(1)
Data file
Input
Slot delimiter
Word delimiter
Bit delimiter
Bit (0...15)
Word
(1)
I/O located on the controller (embedded I/O) is slot 0. I/O added to the controller (expansion I/O) begins with slot 1.
I/O Memory Mapping
For each input module, slot x, words 0...1 in the input data file contain the current state of the
field input points.
Input Data File
Bit Position
Word1514131211109876543210
0 rrrrrrrrrrrrrrrr
1 rrrrrrrrrrrrrrrr
Where: r = read
1762 Expansion I/O Addressing
The addressing scheme for 1762 Expansion I/O is represented in the following figure.
Publication 1762-IN019B-EN-P - June 2013
Page 17
MicroLogix 1762-IQ32T DC Input Module 17
Specifications
General Specifications
Attribute Value
Number of inputs 32
Dimensions
HxWxD
Shipping weight, approx. 200 g (7.05 oz)
Bus current draw, max 170 mA @ 5V DC
Heat dissipation See Derating Charts on page 19
Wire size 22, 24, 26 AWG solid or stranded copper wire rated @ 90°C (194 °F)
Wiring category
Pilot duty rating Not rated
Enclosure type rating IP20
North American temp code T3C
(1)
Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring and
Grounding Guidelines, publication 1770-4.1
(1)
90 x 40.4 x 87 mm
(3.54 x 1.59 x 3.43 in.)
0 mA @ 24V DC
2 - on signal ports
.
Input Specifications
Attribute Value
Isolated groups Group 1: Inputs 0...7
Group 2 : Inputs 8...15
Group 3 : Inputs 16...23
Group 4 : Inputs 24...31
Input group to backplane isolation Verified by one of the following dielectric tests:
1,200V AC for 2 s or 1,697V DC for 2 s
75V DC working voltage (IEC Class 2 reinforced insulation)
Vendor I.D. code 1
Product type code 7
Product code 99
Voltage category 24V DC sink/source
Operating voltage range 10...26.4V DC
10...30V DC See Derating Charts on page 19
Signal delay, max Turn-on = 8.0 ms
Turn-off = 8.0 ms
On-state voltage, min 10 V DC
Publication 1762-IN019B-EN-P - June 2013
Page 18
18 MicroLogix 1762-IQ32T DC Input Module
Input Specifications
Attribute Value
Off-state voltage, max 5 V DC
Off-state current, max 1.0 mA
On-state current, min 1.6 mA @ 10V DC
2 mA @ 15V DC
On-state current, max 5.7 mA @ 26.4V DC
Nominal impedance 4.7 kΩ
IEC input compatibility Type 1
6.5 mA @ 30.0V DC
Environmental Specifications
Attribute Value
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20... 60 °C (-4...140 °F) See Derating Charts on page 19
Temperature, storage IEC 60068-2-1 (Test Ab, Unpackaged Non-operating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Non-operating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Non-operating Thermal Shock):
-40…85 °C (-40…185 °F)
Relative humidity IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5...95% non-condensing
Vibration IEC 60068-2-6 (Test Fc, Operating):
Altitude, operating max 2000 m (6562 ft)
Shock, operating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Shock, nonoperating IEC 60068-2-27 (Test Ea, Unpackaged Shock):
Emissions CISPR 11
ESD immunity IEC 61000-4-2:
Radiated RF immunity IEC 61000-4-3:
5 g @ 10... 500 Hz
30 g
Panel mount - 50 g
DIN mount - 40 g
Group 1, Class A
4 kV contact discharges
8 kV air discharges
4 kV indirect
10V/m with 1 kHz sine-wave 80% AM from 80…2700 MHz
Publication 1762-IN019B-EN-P - June 2013
Page 19
Environmental Specifications
°C
point
3.9W
4.1W
@Vin=26.4V
5.4W
4.8W
5.2W
60
20
3040
44917 44918
Attribute Value
EFT/B immunity IEC 61000-4-4:
±2 kV at 5 kHz on signal ports
Surge transient immunity IEC 61000-4-5:
±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports
Conducted RF immunity IEC 61000-4-6:
10V rms with 1 kHz sine-wave 80% AM from 150 kHz...80 MHz
Derating Charts for each input
32
31
28
24
23
60
26
55
40
30
MicroLogix 1762-IQ32T DC Input Module 19
point
4.8W
@Vin=30.0V
4.1W
3.9W
55
°C
6.8W
32
24
22
19
18
5.1W
Certifications
Certification (when
product is marked)
c-UL-us UL Listed Industrial Control Equipment, certified for US and Canada. See UL File
CE European Union 2004/108/EC EMC Directive, compliant with:
C-Tick Australian Radiocommunications Act, compliant with:
KC Korean Registration of Broadcasting and Communications Equipment,
(1)
See the Product Certification link at http://www.rockwellautomation.com/products/certification for Declaration of
Conformity, Certificates, and other certification details.
Value
(1)
E65584.
UL Listed for Class I, Division 2 Group A,B,C,D Hazardous Locations, certified for
U.S. and Canada. See UL File E194810.
EN 61326-1; Meas./Control/Lab., Industrial Requirements
EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
AS/NZS CISPR 11; Industrial Emissions
compliant with:
Article 58-2 of Radio Waves Act, Clause 3
Publication 1762-IN019B-EN-P - June 2013
Page 20
Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its products. At
http://www.rockwellautomation.com/support/
technical and application notes, sample code and links to software service packs, and a MySupport feature that
you can customize to make the best use of these tools.
For an additional level of technical phone support for installation, configuration and troubleshooting, we offer
TechConnect support programs. For more information, contact your local distributor or Rockwell Automation
representative, or visit http://www.rockwellautomation.com/support/
, you can find technical manuals, a knowledge base of FAQs,
.
Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the information that's
contained in this manual. You can also contact a special Customer Support number for initial help in getting your
product up and running.
United States or
1.440.646.3434
Canada
Outside United
States or
Canada
Use the Worldwide Locator
at
http://www.rockwellautomation.com/support/americas/phone_en.html, or
contact your local Rockwell Automation representative.
New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the
manufacturing facility. However, if your product is not functioning and needs to be returned, follow these
procedures.
United States Contact your distributor. You must provide a Customer Support case
number (call the phone number above to obtain one) to your distributor
to complete the return process.
Outside United States Please contact your local Rockwell Automation representative for the
return procedure.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to
improve this document, complete this form, publication RA-DU002
http://www.rockwellautomation.com/literature/
Allen-Bradley, Rockwell Automation, MicroLogix, and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
.
, available at
Publication 1762-IN019B-EN-P - June 2013
Supersedes Publication 1762-IN019A-EN-P - August 2009 Copyright © 2013 Rockwell Automation, Inc. All rights reserved.
Loading...