Allen-Bradley 140G-G6C3-C63-KJ-MT, 140G-G2C3-C80-KJ Installation Manual

DIR 1000719R0001 Version 02 - 140G-G_ ; 140MG-G_

LENGTH M

73 mm (2.87") M 4

M

M 4

Installation instruction for 140G-G, 140MG-G
Istruzioni di installazione
Installationsanleitung
Instructions pour l’installation
Instrucciones de instalación

Installation - Installazione - Instalación
Instalação - -

WARNING: To prevent electrical shock, disconnect from power source before

installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).

AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).

WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur

Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).

AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation

secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).

ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).

ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).

警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。（NFPA70Eの要件に従ってください）

警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）物

Bul. 140G/140MG

1

CLACK

3p

4p

Mounting hardware

0.13"ø
ø 3.5 mm

from 0.51" to 0.55"

from 13 mm to 14 mm

140G-G-MH3

x2

140G-G-MH4

x3

CH 7

x2x3x2

x3

Phase

barrier

140G-G-PB3M

x4

140G-G-PB4M

x6

End cap kit Carter Insulator

CH 5

LEN GT H M

1 4 m m (0.55" ) M 6

x6

x8

LEN GT H ø

1 2 mm (0.47" ) 3

x2

x2

x2

Insulator

x2

Side

cover

x1

x1

DIR 1000719R0001 Version 02

1

Maximum recommended conductor support distance

7.87"/200 mm7.87"/200 mm

2

- Use cable or insulated busbars/ or perform specific type test on the installation.

- Usare cavi o barre isolate/ o eseguire prove di tipo specifiche sull' installazione.

- Kabel oder isolierte Sammelschienen verwenden/ oder die spezifische Typprüfung auf derInstallation durchführen.

- Utiliser un câble ou des barres isolées/ ou réaliser un test de type spécifique sur installation.

- Utilizar un cable o barras aisladas/ o efectuar una prueba de tipo específico sobre instalacíon.

DIR 1000719R0001 Version 02

(2)

3

A B C D E

III-IV

3.11"

79 mm

1.69"

43 mm

1.85"

47 mm

0.59"

15 mm

0.93"

23.5 mm

III

2.79"

71 mm

1.85"

47 mm

2.87"

73 mm

0.67"

17 mm

1.44"

36.5 mm

IV

2.79"

71 mm

1.85"

47 mm

3.86"

98 mm

0.67"

17 mm

1.44"

36.5 mm

III

2.91"

74 mm

2.16"

55 mm

3.19"

81 mm

0.83"

21 mm

1.59"

40.5 mm

IV

2.91"

74 mm

2.16"

55 mm

4.17"

106 mm

0.83"

21 mm

1.59"

40.5 mm

WITH ESCUTCHEON

WITHOUT ESCUTCHEON

MANDATORY FOR
UL APPLICATIONS
NOT REQUIRED FOR
IEC APPLICATIONS

IV ONL

Ø 0.18"
Ø 4.5 mm-M4

IV ONL

Y

Y

0.49"/12.5 mm

X

2.11"/53.5 mm

Y

IV ONLY

0.98"/25 mm0.98"/25 mm

Y

IV ONL

Y

IV ONL

D

B

X

Y

X

Y

E

C

8,9 lb-in

1,1 Nm

A

2

Y

1.97"/50 mm

X

0.49"/12.5 mm

1

4.21"/107 mm

OK

3

4

4

DIR 1000719R0001 Version 02

Ø 0.26"

Ø 6.5

Ø min 0.26"

min 6,5

min 0.26"

Ø min 6,5

0.2"(5) max

0.14"(3.5) min

A max

max 0.63"

max 16

(3)

0.63"
16

140G-G

140MG-G

A

A

0.29"

7.5

0.24"
6

In

Fixed
Fixed
Fixed
Fixed

Type

Fixed
Fixed

Fixed
Fixed
Fixed
Fixed
Fixed
Fixed

500

100
110
125

160*

50
60
63
70
80
90

500
500
600

1600112Adjustable

30
32
35

I3

500
500
500
500

630

Min Med Max I3

500
500

136 160

I1

15
16
20
25
30

1250

110
125

32
35
40
50
60
63

700
800

900
1000
1100

Type

70
80
90

100

In

15
16
20
25

40

Fixed
Fixed
Fixed

Fixed
Fixed

5

ONLY REQUIRED FOR THROUGH THE DOOR APPLICATION

(WITH DOOR OF THE PANEL ≤0.98"/25 mm FROM THE FRONT)

1

2

6

I1(A)

DIR 1000719R0001 Version 02

100

In=100A

I3(A)

1000

140G-G THERMOMAGNETIC TRIP UNIT

*IEC ONLY

(4)

7

HĊ ĂĖÅ

F G H I

800 900 1000 1100

A B C D E

300 400 500 600 700

1

CLACK

USE FLAT BLADE
SCREW DRIVER

2

140MG-G MAGNETIC ONLY TRIP UNIT

In=200A

A

I

BEH

G

FCD

- Manually trip the breaker prior to any adjustment of the magnetic trip settings.

- E’obbligatorio mettere l'interruttore in posizione Trip test prima di regolare il termomagnetico.

- Der Leistungsschalter muss vor Einstellung des thermomagnetischen Auslösers zwingend in die Prüfstellung geschaltet werden.

- Il est obligatoire de mettre le disjoncteur en position de Test de Déclenchement avant de régler le déclencheur magnétothermique.

- Es obligatorio situar el interruptor en posición “Test de Disparo” antes de realizar el ajuste del relé termomagnético.

I3

In A B C D E F G H I

3 from 4 In to 11 In 12 15 17 20 23 25 28 30 33

7 from 4 In to 11 In 28 34 40 46 53 59 65 71 77
15 from 3 In to 11 In 45 60 75 90 105 120 135 150 165
30 from 3 In to 11 In 90 120 150 180 210 240 270 300 330
50 from 3 In to 11 In 150 200 250 300 350 400 450 500 550
70 from 3 In to 11 In 210 280 350 420 490 560 630 700 770
80 from 3 In to 11 In 240 320 400 480 560 640 720 800 880

100 from 3 In to 11 In 300 400 500 600 700 800 900 1000 1100
125 from 3 In to 11 In 375 500 625 750 875 1000 1125 1250 1375

Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page

Publication 140G-IN076C-MU-P - S eptember 2015

DIR 1000719R0001 Version 02 (L9694) - B0301

Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.