Allegro UDN2547EB, UDN2547B, UDQ2547EB, UDQ2547B, UDK2547EB Datasheet
...
2547
PROTECTED
QUAD POWER DRIVERS
Providing interface between low-level logic and power loads, the
UDK/UDN/UDQ2547B and UDK/UDN/UDQ2547EB quad power
drivers combine logic gates and high-current bipolar outputs with
complete output protection. Each of the four outputs will sink 600 mA
in the ON state. The outputs have a minimum breakdown voltage
(load dump) of 60 V and a sustaining voltage of 40 V. The inputs are
compatible with TTL and 5 V CMOS logic systems and include internal
pull-down resistors to ensure that the outputs remain OFF if the inputs
are open-circuited.
Over-current protection for each channel has been designed into
these devices and is activated at approximately 1.3 A. It protects each
output from short circuits with supply voltages up to 25 V. When a
maximum driver output current is reached, that output drive is reduced
linearly, maintaining a constant load current. If the over-current or
short circuit condition continues, each channel has an independent
thermal limit circuit which will sense the rise in junction temperature
and turn OFF the individual channel that is at fault. Foldback circuitry
decreases the output current if excessive voltage is present across the
output and assists in keeping the device within its SOA (safe operating
area).
Each output also includes diagnostics for increased device protection. If any output is shorted or opened, the diagnostics can signal the
controlling circuitry through a common FAULT pin.
These devices can be used to drive various resistive loads including incandescent lamps (without warming or limiting resistors). With
the addition of external output clamp diodes, they can be used to drive
inductive loads such as relays, solenoids, or dc stepping motors.
The suffix ‘B’ devices are 16-pin power DIPs while the suffix ‘EB’
devices are 28-lead power PLCCs for surface-mount applications.
Both packages are of batwing construction to provide for maximum
package power dissipation.
UDx2547B
2547
PROTECTED
QUAD POWER DRIVERS
ABSOLUTE MAXIMUM RATINGS
at T
A
= 25°C
Output Voltage, V
OUT
............................ 60 V
Over-Current Protected Output Voltage,
V
OUT
............................................... 25 V
Output Current, I
OUT
.......................... 1.3 A*
FAULT Output Voltage, V
F
................... 40 V
Supply Voltage, V
CC
............................ 7.0 V
Input Voltage, V
IN
or VEN...................... 7.0 V
Package Power Dissipation,
P
D
........................................ See Graph
Operating Temperature Range, T
A
Prefix ‘UDK’ ............... -40°C to +125°C
Prefix ‘UDN’ ................. -20
°C to +85°C
Prefix ‘UDQ’................. -40
°C to +85°C
Storage Temperature Range,
T
S
............................... -55°C to +150°C
*Outputs are current limited at approximately
1.3 A per driver and junction temperature limited
if current in excess of 1.3 A is attempted. See
Circuit Description and Application for further
information.
Always order by complete part number: a prefix to indicate operating temperature range + the basic four-digit part number + a suffix to
indicate package style, e.g., UDK2547EB .
FEATURES
■ Output SOA Protection ■ Low Output-Saturation Voltage
■ Diagnostic FAULT Output ■ TTL and 5 V CMOS Compatible Inputs
■ Independent Over-Current Protection for Each Driver
■ Independent Thermal Protection for Each Driver
■ 600 mA Output Current per Channel
Data Sheet
29317.4C
1
2
3
14
4
5
6
7
89
10
11
12
13
15
16
ENABLE
GROUND
GROUND
OUT
3
NO
CONNECT.
GROUND
GROUND
OUT
2
OUT
1
FAULT
OUT
4
V
CC
IN
4
Dwg. PP-018A
IN
1
IN
2
IN
3
SUPPLY
2547
PROTECTED
QUAD POWER DRIVERS
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
UDx2547EB
FUNCTIONAL BLOCK DIAGRAM
<<1 Ω
OUT
Dwg. FP-007
N
FAULT
COMMON CONTROL
ONE OF FOUR DRIVERS
ABLE
IN
N
CURRENT
LIMIT
THERMAL
SHUTDOWN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
GROUND
GROUND
GROUND
GROUND
Dwg. PP-019
NO
CONNECTION
NC
ENABLE
SUPPLY
NC
CC
V
OUT
1
OUT
2
OUT
3
OUT
4
IN
4
IN
3
IN
2
IN
1
NO
CONNECTION
NO
CONNECTION
FAULT
NC
FAULT
W
Copyright © 1989, 1993, Allegro MicroSystems, Inc.
50 75 100 125 150
10
6
4
2
0
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
TEMPERATURE IN °C
8
25
R = 6°C/W
θJT
Dwg. GP-004-1A
SUFFIX 'EB', R = 36°C/W
θJA
SUFFIX 'B', R = 43°C/W
θJA
2547
PROTECTED
QUAD POWER DRIVERS
STATUS IN
N
ENABLE OUT
N
FAULT
Normal Load H H L H
LH HH
XL HH
Over-Current or
Short to Supply H H R L
Thermal Fault H H H L
Open Load or
Short to Ground L H L L
ELECTRICAL CHARACTERISTICS at T
A
= +25°C (prefix ‘UDN’) or over operating
temperature range (prefix ‘UDK’ or ‘UDQ’), V
CC
= 4.75 V to 5.5 V
Limits
Characteristic Symbol Test Conditions Min. Typ. Max. Units
Output Leakage Current* I
OUT
V
OUT
= 60 V, VIN = 0.8 V, VEN = 2.0 V — 30 150 µA
V
OUT
= 60 V, VIN = 2.0 V, VEN = 0.8 V — 30 150 µA
Output Sustaining Voltage V
OUT(SUS)
I
OUT
= 100 mA, V
IN
= 0.8 V, V
CC
= Open 40 — — V
Output Saturation Voltage V
OUT(SAT)
I
OUT
= 400 mA — — 300 mV
I
OUT
= 500 mA — — 400 mV
I
OUT
= 600 mA — — 550 mV
Over-Current Limit I
OUT
5 ms PulseTest, V
OUT
= 5.0 V — 1. 3 1.7 A
Input Voltage Logic 1 V
IN(1)
or V
EN(1)
2.0 — — V
Logic 0 V
lN(0)
or V
EN(0)
— — 0.8 V
Input Current Logic 1 V
IN(1)
or V
EN(1)
= 2.0 V — — 60 µA
Logic 0 V
IN(0)
or V
EN(0)
= 0.8 V 10 — — µA
Fault Output Leakage Current I
F
VF = 40 V — <1.0 2.0 µA
Fault Output Current I
F
VF = 40 V, Driver Outputs Open,
V
IN
= 0.8 V, V
EN
= 2.0 V 40 60 80 µA
Fault Output Saturation Voltage V
F(SAT)
IF = 30 µA — 0.1 0.4 V
Total Supply Current I
CC
All Outputs ON — 45 50 mA
All Outputs OFF — 6.0 10 mA
Thermal Shutdown T
J
— 165 — °C
Thermal Hysteresis ∆T
J
—15— °C
Typical Data is for design information only.
*Measurement includes XOR input current
and other elements.
X = Don’t care. R = Linear drive, current limited.
TRUTH TABLE
Loading...