Allegro UDN2585A, UDN2580A, UDN2588A Datasheet

This versatile family of integrated circuits will work with many combina­tions of logic- and load-voltage levels, meeting interface requirements beyond
the capabilities of standard logic buffers. Series UDN2580A and A2580SLW
source drivers can drive incandescent, LED, or vacuum fluorescent displays.
Internal transient-suppression diodes permit the drivers to be used with
inductive loads such as relays, solenoids, dc and stepping motors, and mag­netic print hammers.

The Types UDN2580A and A2580SLW are high-current source drivers
used to switch the ground ends of loads that are directly connected to a -50 V
supply. Typical loads are telephone relays, PIN diodes, and LEDs.

The UDN2585A and A2585SLW are drivers designed for applications
requiring low output saturation voltages. Typical loads are low-voltage LEDs
and incandescent displays. The eight non-Darlington, 25 V outputs will
simultaneously sustain continuous load currents of -120 mA at ambient
temperatures to +70°C.

The UDN2588A and A2588SLW have separate logic and driver supply
lines. Their eight drivers can serve as an interface between positive logic
(TTL, CMOS, PMOS) or negative logic (NMOS) and either negative or split­load supplies to -80 V.

These drivers are packaged in plastic DlPs (suffix A) or surface-mount­able wide-body SOlCs (suffix LW), and are rated for operation over the
temperature range of -20°C to +85°C.

FEATURES

■ TTL, CMOS, PMOS, NMOS Compatible

■ High Output-Current Rating

■ Internal Transient Suppression

■ Efficient Input/Output Structure

■ Through-Hole and Surface-Mount Packages

8-CHANNEL SOURCE DRIVERS

Always order by complete part number, e.g., UDN2580A .

Data Sheet

29316C*

UDN2580A and UDN2585A

ABSOLUTE MAXIMUM RATINGS

See next page.

2580, 2585,

AND

2588

2580, 2585, AND 2588

8-CHANNEL
SOURCE DRIVERS

115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]

2

ABSOLUTE MAXIMUM RATINGS

at 25°C Free-Air Temperature for any one driver (unless otherwise noted).

UDN2580A UDN2585A UDN2588A
A2580SLW A2585SLW A2588SLW

Output Voltage, V

CE

50 V 25 V 80 V

Supply Voltage, V

S

(ref. sub.) 50 V 25 V 80 V

Supply Voltage, VCC (ref. sub.) — — 80 V

Input Voltage, V

IN

(ref. VS) -30 V -20 V -30 V

Total Output Current, (l

C

+ IS) -500 mA -250 mA -500 mA

Substrate Current I

SUB

3.0 A 2.0 A 3.0 A

Package Power Dissipation, P

D

(single output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 W

(total package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Graph

Operating Temperature Range, T

A

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20°C to +85°C

Storage Temperature Range, T

S

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +150°C

50 75 100 125 150

2.5

0.5

0

ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS

AMBIENT TEMPERATURE IN °C

2.0

1.5

1.0

25

Dwg. GP-022-1

18-PIN DIP, R = 60°C/W

θJA

20-PIN DIP, R = 55°C/W

θJA

20-LEAD SOIC, R = 70°C/W

θJA

W
Copyright © 1981, 2000 Allegro MicroSystems, Inc.

2580, 2585, AND 2588

8-CHANNEL

SOURCE DRIVERS

www.allegromicro.com

3

TYPICAL OPERATING VOLTAGES

V

S

V

lN(ON)

V

lN(OFF)

V

CC

V

EE(MAX)

Device Types

0 V -15 V to -3.6 V -0.5 V to 0 V NA -25 V UDN2585A & A2585SLW

-50 V UDN2580A & A2580SLW

+5 V 0 V to +1.4 V +4.5 V to +5 V NA -20 V UDN2585A & A2585SLW

-45 V UDN2580A & A2580SLW

≤ 5 V -75 V UDN2588A & A2588SLW

+12 V 0 V to +8.4 V +11.5 V to +12 V NA -13 V UDN2585A & A2585SLW

-38 V UDN2580A & A2580SLW

≤12 V -68 V UDN2588A & A2588SLW

+15 V 0 V to +11.4 V +14.5 V to +15 V NA -10V UDN2585A & A2585SLW

-35 V UDN2580A & A2580SLW

≤15 V -65 V UDN2588A & A2588SLW

NOTE: The substrate must be tied to the most negative point in the external circuit to maintain isolation between drivers and to provide

for normal circuit operation.

For simplification, these devices are characterized on the following pages with
specific voltages for inputs, logic supply (VS), load supply (VEE), and collector
supply (VCC). Typical use of the UDN2580A and A2580SLW is with negative­referenced logic. The more common application of the UDN2585A, A2585SLW,
UDN2588A and A2588SLW are with positive-referenced logic supplies. In
application, the devices are capable of operation over a wide range of logic and
supply voltage levels:

2580, 2585, AND 2588

8-CHANNEL
SOURCE DRIVERS

115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]

4

Dwg. No. A-11,358

UDN2580A and A2580SLW
ELECTRICAL CHARACTERISTICS at T

A

= +25°C, VS = 0 V, VEE = -45 V (unless otherwise noted).

Limits

Characteristic Symbol Test Conditions Min. Max. Units

Output Leakage I

CEX

VlN = -0.5 V, V

OUT

= VEE = -50 V — 50 µA

Current VlN = -0.4 V, V

OUT

= VEE = -50 V, TA = 70°C — 100 µA

Output Sustaining V

CE(SUS)

VlN = -0.4 V, I

OUT

= -25 mA, Note 1 35 — V

Voltage

Output Saturation V

CE(SAT)

VlN = -2.4 V, I

OUT

= -100 mA — 1.8 V

Voltage VlN = -3.0 V, I

OUT

= -225 mA — 1.9 V

VlN = -3.6 V, I

OUT

= -350 mA — 2.0 V

Input Current I

IN(ON)

VlN = -3.6 V, I

OUT

= -350 mA — -500 µA

VlN = -15 V, I

OUT

= -350 mA — -2.1 mA

I

IN(OFF)

I

OUT

= -500 µA, TA = 70°C, Note 3 -50 — µA

Input Voltage V

IN(ON)

I

OUT

= -100 mA, VCE ≤1.8 V, Note 4 — -2.4 V

I

OUT

= -225 mA, VCE ≤1.9 V, Note 4 — -3.0 V

I

OUT

= -350 mA, VCE ≤2.0 V, Note 4 — -3.6 V

V

IN(OFF)

I

OUT

= -500 µA, TA = 70°C-0.2— V

Clamp Diode I

R

VR = 50 V, TA = 70°C — 50 µA

Leakage Current

Clamp Diode V

F

IF = 350 mA — 2.0 V

Forward Voltage

Input Capacitance C

IN

— 25 pF

Turn-On Delay t

PHL

0.5 EIN to 0.5 E

OUT

— 5.0 µs

Turn-Off Delay t

PLH

0.5 EIN to 0.5 E

OUT

— 5.0 µs

Dwg. PP-064

UDN2580A A2580SLW

Dwg. No. A-11,359

PARTIAL SCHEMATICNOTES: 1. Pulsed test, t

p

≤ 300 µs,

duty cycle ≤ 2%.

2. Negative current is
defined as coming out of the
specified device pin.

3. The I

IN(OFF)

current limit

guarantees against partial
turn-on of the output.

4. The V

IN(ON)

voltage limit
guarantees a minimum
output source current per the
specified conditions.

5. The substrate must
always be tied to the most
negative point and must be at
least 4.0 V below V

S

.

13

14

15

16

17

19

12

18

20

11

1

2

3

8

9

4

5

6

7

10NCNC

SUB/V

EE

SUB

+V

S