MODEL 035350-010-FR001
ASSEMBLY AND DRESSING INSTRUCTIONS
Blending innovative design, cutting-edge technology and the grace and elegance of traditional crystal, ALLEGRI® proudly brings you a new approach
to lighting. ALLEGRI® fixtures are made from the finest raw materials and are brought to life through a combination of traditional manufacturing, such
as sand casting, hand-forging and technology driven techniques including laser cutting.
Enclosed are detailed instructions on how to properly install your fixture. Please read all instructions carefully. If you need further assistance, please
contact the dealer from which you purchased this product or call 800-525-2655 to speak with an ALLEGRI® customer service representative. We hope
you enjoy your fixture!
WWW.ALLEGRICRYSTAL.COM
800.525.2655
P1
ASSEMBLY AND DRESSING INSTRUCTIONS
GENERAL NOTES
v For your safety and proper operation of fixture, read and understand all instructions completely before commencing installation.
v This fixture is suited for dry locations. Never install fixture on damp ceiling; room should be dry and well ventilated.
v Extreme care should be taken to avoid damage to the surface of lighting fixture and wires. Wearing gloves is recommended for installation.
v Connect ribbed wire of lighting fixture to live wire, while smooth wire of lighting to neutral. Connect bare copper or silver color ground wire of
fixture to the double colored or green wire of outlet box.
v Use UL LISTED wire nuts for the wiring connections in this fixture. Wrap wire nut connections with UL LISTED electrical tape.
v Keep lighting away from acid, alkali and other corrosive chemical or gas; clean the fixture with a clean cloth only.
v Fixture must be firmly secured when installing ceiling tube, chain pipe and other connecting parts.
v Never cover the lighting fixture when power is connected.
v Disconnect the power before installing, cleaning and/or replacing light bulb.
v Extreme care should be taken when installing and cleaning of Glass and/or Crystal Components.
v This product is rated 110-130V/60HZ bulb 40W Maximum.
v Save these instructions for future reference.
WARNING
The electricity must be turned off at the main fuse box or circuit breaker before installing this fixture. Turning the power off using the light switch may
not be sufficient to prevent electrical shock.
*ALLEGRI will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
WARNING!
CONTENTS ARE FRAGILE
HANDLE WITH CARE
THE METAL FRAME, FINISH AND CRYSTAL COMPONENTS OF THIS CHANDELIER ARE VERY DELICATE.
PLEASE EXERCISE EXTREME CAUTION DURING UNPACKING AND INSTALLATION.
PLACE ALL PIECES TOGETHER IN A NUMERICAL ORDER AND IN THE ORIENTATION DEPICTED.
REFER TO THE PARTS LIST TO AVOID ANY CONFUSION BETWEEN PARTS THE PARTS NUMBER MUST COINCIDE.
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY AND
PROPERTY DAMAGE. All electrical components must be installed only by a Licensed Electrician.
This product must be installed in accordance with the National Electric Code (NEC), and appropriate local electrical code(s), by a
person familiar with the construction and operation of the product and the hazard involved.*
CAUTION: Do not exceed maximum wattage note on fixture. Uses only recommended bulbs with fixture.
WWW.ALLEGRICRYSTAL.COM
866.820.2665
P2
CANOPY MOUNTING INSTRUCTION
WWW.ALLEGRICRYSTAL.COM
800.525.2655
WARNING
Electrical Danger
Turn Power Off
All electrical components must be
installed by a licensed electrician in
accordance with the National
Electric code and the appropriate
local electrical codes.
c
R
P3
Canopy
Grub screw
Outlet box (by others)
Mounting block
8/32 Screw
INSTALL CANOPY AS FOLLOWS
CAUTION: Be sure power is off at the main
breaker box prior to installation.
1. Install cross bar to outlet box with two 8/32
original screws.
2. Raise assembled frame with stems and
canopy close enough and make electrical
connections
3. Secure canopy with flat head screws
WWW.ALLEGRICRYSTAL.COM
800.525.2655
FRAME ASSEMBLY INSTRUCTIONS
MODEL 035350
INSTALLATION
a. Turn off electricity, take all parts from part box.
b. Connect the main wire with the power supply
circuit. See wire connection diagram.
c. Fix part #4 to part #5 by using thread rod,use
the same way to installing other part
d. Fix part #4、#5、#6 to part #2 by using part #1.
e. Put part #1、#2、#4、#5、#6 through part #3
then screw to part #7.
f. Check the installation and attach bulb into lamp
holder.
P4
C20-16-06-01
8X
4X
7-MAIN BODY
40W bulbs
C20-16-06-01
8X
4X
1-HEX NUT
2-ROLLING PLATE
3-CANOPY
4-STEEVE A
5-STEEVE B
6-STEEVE C
THREAD ROD
ATTENTION
1. Take all crystal or glass parts carefully
from carton, then put them on a clean cloth.
2. Start hanging crystals from bottom center to
top of fixture in an numerical order
as shown in diagram
You will need 12 - Cand.Buld
40 Watts Recommended
40 Watts Max
Bulb not included
CRYSTAL DRESSING INSTRUCTION
WWW.ALLEGRICRYSTAL.COM
800.525.2655
MODEL 035350-010-FR001
WARNING
Electrical Danger
Turn Power Off
All electrical components must be
installed by a licensed electrician in
accordance with the National
Electric code and the appropriate
local electrical codes.
c
R
P5
L
K2020/22#
Qty
A1
22
100
22
100
L
K610/ W22*L100*T10mm
R20610-100-00-09
K2020/22#
A
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A16
A15
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
K610/ W22*L100*T10mm
R20610-100-00-09
1500 55PCS
53PCS
52PCS
51PCS
50PCS
49PCS
48PCS
47PCS
46PCS
45PCS
44PCS
43PCS
42PCS
41PCS
40PCS
39PCS
38PCS
37PCS
36PCS
34PCS
33PCS
32PCS
31PCS
30PCS
29PCS
28PCS
27PCS
26PCS
25PCS
24PCS
23PCS
35PCS
1472
1444
1416
1388
1360
1332
1304
1276
1248
1220
1192
1164
1136
1108
1080
1052
1024
968
940
912
884
996
856
828
800
772
744
716
688
660
632
66
C20-16-06-01
C20-16-06-01
C20-16-06-01
C20-16-06-01
C20-16-06-01
C20-16-06-01
A1
A32
A1
A32
C20-16-06-01
Code
LIGHTING CARE INFORMATION
Every ALLEGRI® fixture is o f heirloom quality and wi ll l ast for generations. To e ns ure it retains its bril li an ce and
splendor for years to come, proper care and regular cleaning are necessary.
It is recommended that ALLEGRI® fixture, and particularly their crystal trim, be lightly dusted with a feather or lambs wool
du ste r, or sof t b rus h eve ry two mo nth s, or wh ene ver it ap pea rs du ll or dus ty. A thoro ugh cl ean ing sh ou ld be
completed every six months.
Before cleaning an ALLEGRI® fixture, first locate the fixture's trim diagram. This will assist in replacing the crystal trim in
its proper location after cleaning. Should a replacement trim diagram be required, please call
866-820-2665 to speak with an ALLEGRI® customer service representative, who can provide a new diagram.
ALLEGRI® recommends several dif ferent cleaning methods, depending on the typ e of fixture. Some fixtures can be
cleaned with limited removal of crystal, while others must be completely untrimmed.
Place a soft towel or blanket directly beneath the fixture to limit the damage to both the crystal and the surface below the
fixture, should a piece of crystal be dislodged during the cleaning process. Extreme care must be taken around any
electrical fixture. For personal safety and the safety of the fixture, be sure that the fixture has been turned off. Never rotate or
spin the fixture as this can cause the fixture to lose support and fall. Instead, move around the fixture while cleaning.
White Glove Method
Prepare a cleaning solution of one part isopropyl alcohol to three parts distilled water and place in a clean spray bottle.
Do not use packaged cleaning fluids, as many of these contain ammonia, which may degrade the finish of the fixture and
the quality of the crystal.
Wearing white cotton gloves, spray one glove with the solution and keep one dry. Gently polish each crystal with the damp
glo v e an d imm e diat e ly w i pe i t wi t h th e dry glov e . Do not t ug o r pul l on t he c r yst a l, a s thi s may caus e the
connectors to chip or crack the crystal, or dislodge it from the fixture.
Warning: To reduce the risk of personal injury due to fire and/or electric shock, never spray solution at or near the fixture.
Crystal Removal Method
Gently remove trim and hand-wash the crystal in lukewarm water using a mild detergent. Rinse in clean water and dry with a
soft clea n cloth. Do n ot soak f in ished cry st al such a s SWAROVSKI E LEMENTS Col ors: Teak, Go lden Shad ow or
Silver Shade, for extended periods, as this may degrade the crystal's finish.
With the fixture untrimmed and turned off, wipe the frame, including the light bulbs once they are completely cool, with a soft
cloth.
Wearing white gloves, finger-cots or using a soft clean cloth, gently replace the trim as directed in the trim diagram.
WWW.ALLEGRICRYSTAL.COM
866.820.2665
P6
Loading...