Ø
6
W27*H60
B220-0006-00
Ø6
Ø
6
MODEL 033251-014-FR001
ASSEMBLY AND DRESSING INSTRUCTIONS
Blending innovative design, cutting-edge technology and the grace and elegance of traditional crystal, ALLEGRI® proudly brings you a new approach
to lighting. ALLEGRI® fixtures are made from the finest raw materials and are brought to life through a combination of traditional manufacturing, such
as sand casting, hand-forging and technology driven techniques including laser cutting.
Enclosed are detailed instructions on how to properly install your fixture. Please read all instructions carefully. If you need further assistance, please
contact the dealer from which you purchased this product or call 800-525-2655 to speak with an ALLEGRI® customer service representative. We hope
you enjoy your fixture!
WWW.ALLEGRICRYSTAL.COM
P1
800.525.2655
ASSEMBLY AND DRESSING INSTRUCTIONS
WARNING!
CONTENTS ARE FRAGILE
HANDLE WITH CARE
THE METAL FRAME, FINISH AND CRYSTAL COMPONENTS OF THIS CHANDELIER ARE VERY DELICATE.
PLEASE EXERCISE EXTREME CAUTION DURING UNPACKING AND INSTALLATION.
PLACE ALL PIECES TOGETHER IN A NUMERICAL ORDER AND IN THE ORIENTATION DEPICTED.
REFER TO THE PARTS LIST TO AVOID ANY CONFUSION BETWEEN PARTS THE PARTS NUMBER MUST COINCIDE.
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY AND
PROPERTY DAMAGE. All electrical components must be installed only by a Licensed Electrician.
This product must be installed in accordance with the National Electric Code (NEC), and appropriate local electrical code(s), by a
person familiar with the construction and operation of the product and the hazard involved.*
CAUTION: Do not exceed maximum wattage note on fixture. Uses only recommended bulbs with fixture.
GENERAL NOTES
For your safety and proper operation of fixture, read and understand all instructions completely before commencing installation.
This fixture is suited for dry locations. Never install fixture on damp ceiling; room should be dry and well ventilated.
Extreme care should be taken to avoid damage to the surface of lighting fixture and wires. Wearing gloves is recommended for installation.
Connect ribbed wire of lighting fixture to live wire, while smooth wire of lighting to neutral. Connect bare copper or silver color ground wire of
fixture to the double colored or green wire of outlet box.
Use UL LISTED wire nuts for the wiring connections in this fixture. Wrap wire nut connections with UL LISTED electrical tape.
Keep lighting away from acid, alkali and other corrosive chemical or gas; clean the fixture with a clean cloth only.
Fixture must be firmly secured when installing ceiling tube, chain pipe and other connecting parts.
Never cover the lighting fixture when power is connected.
Disconnect the power before installing, cleaning and/or replacing light bulb.
Extreme care should be taken when installing and cleaning of Glass and/or Crystal Components.
This product is rated 110-130V/60HZ bulb 40W Maximum.
Save these instructions for future reference.
WARNING
The electricity must be turned off at the main fuse box or circuit breaker before installing this fixture. Turning the power off using the light switch may
not be sufficient to prevent electrical shock.
*ALLEGRI will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
WWW.ALLEGRICRYSTAL.COM
P2
800.525.2655
CANOPY MOUNTING INSTRUCTION
WARNING
Outlet box (by others)
Mounting block
Solid Nipple
8
" Screw
32
Canopy
Collar loop
Electrical Danger
All electrical components must be
installed by a licensed electrician in
accordance with the National
Electric code and the appropriate
local electrical codes.
Turn Power Off
R
c
Collar loop ring
Easy link (2pcs)
Chain
INSTALL CANOPY AS FOLLOWS
CAUTION: Be sure power is off at the main
breaker box prior to installation.
1. Drill a hole on main ceiling beam and pass
Solid Nipple through.
2. Place Washer and Hex Nut on top of Solid
Nipple to hold.
3. Take Outlet Box through Solid Nipple and
screw Plate Hickey, then screw Plate Hickey
to main ceiling beam with 4 screws.
4. Secure the Washer and Hex Nut to Solid
Nipple from top side of main ceiling beam.
5. Screw Collar Loop to Nipple as shown, raise
Canopy flat to ceiling and secure it with
Collar Loop Ring.
6. Hang Chain to Collar Loop with the Easy
Link, Proceed to fixture frame assembly Step
1.
P3
WWW.ALLEGRICRYSTAL.COM
800.525.2655
MODEL 033251
FRAME ASSEMBLY INSTRUCTIONS
1.LOOP
2.Hanging crystal ring A
3.Round tube
4.Main body
5.Screw
C10-15-02-00
6.Hanging crystal ring B
7.Hanging crystal ring C
C10-15-02-00
Screw
8.Steeve
C10-15-02-00
9.Hanging crystal ring D
INSTALLATION
a. Turn off electricity, take all parts from part
box.
b. Connect the main wire with the power supply
circuit. See wire connection diagram.
c. Put part #3 through part #2 then screw to
part #1
、#4.
d. Fix part #7,#8
e. Check the installation and attach bulb into
lamp holder.
,#9 to part #4 by using screw.
P4
WWW.ALLEGRICRYSTAL.COM
800.525.2655
MODEL 033251
CRYSTAL DRESSING INSTRUCTION
WARNING
ATTENTION
1. Take all crystal or glass parts carefully
from carton, then put them on a clean
cloth.
2. Start hanging crystals from bottom center
to top of fixture in an alphabetical order
as shown in diagram
Ø
6
W27*H60
B220-0006-00
Ø6
Ø
6
A
B
Electrical Danger
All electrical components must be
installed by a licensed electrician in
accordance with the National
Electric code and the appropriate
local electrical codes.
You will need 13 - Cand.Buld
40 Watts Recommended
40 Watts Max
Bulb not included
Turn Power Off
R
c
C
D
C10-15-02-00
E
Code
Qty
201
A
B
10
C 10
C10-15-02-00
D
E
D
E
48
48
K2020/20#,1Pcs
A
B
2Pcs
D
E
3Pcs
3Pcs
2Pcs
C
D
E
P5
WWW.ALLEGRICRYSTAL.COM
800.525.2655
LIGHTING CARE INFORMATION
Every ALLEGRI® fixture is of heirloom quality and will last for generations. To ensure it retains its brilliance and
splendor for years to come, proper care and regular cleaning are necessary.
It is recommended that ALLEGRI® fixture, and particularly their crystal trim, be lightly dusted with a feather or lambs wool
duster, or soft brush every two months, or whenever it appears dull or dusty. A thorough cleaning should be
completed every six months.
Before cleaning an ALLEGRI® fixture, first locate the fixture's trim diagram. This will assist in replacing the crystal trim in
its proper location after cleaning. Should a replacement trim diagram be required, please call
866-820-2665 to speak with an ALLEGRI® customer service representative, who can provide a new diagram.
ALLEGRI® recommends several different cleaning methods, depending on the type of fixture. Some fixtures can be
cleaned with limited removal of crystal, while others must be completely untrimmed.
Place a soft towel or blanket directly beneath the fixture to limit the damage to both the crystal and the surface below the
fixture, should a piece of crystal be dislodged during the cleaning process. Extreme care must be taken around any
electrical fixture. For personal safety and the safety of the fixture, be sure that the fixture has been turned off. Never rotate or
spin the fixture as this can cause the fixture to lose support and fall. Instead, move around the fixture while cleaning.
White Glove Method
Prepare a cleaning solution of one part isopropyl alcohol to three parts distilled water and place in a clean spray bottle.
Do not use packaged cleaning fluids, as many of these contain ammonia, which may degrade the finish of the fixture and
the quality of the crystal.
Wearing white cotton gloves, spray one glove with the solution and keep one dry. Gently polish each crystal with the damp
glove and immediately wipe it with the dry glove. Do not tug or pull on the crystal, as this may cause the
connectors to chip or crack the crystal, or dislodge it from the fixture.
Warning: To reduce the risk of personal injury due to fire and/or electric shock, never spray solution at or near the fixture.
Crystal Removal Method
Gently remove trim and hand-wash the crystal in lukewarm water using a mild detergent. Rinse in clean water and dry with a
soft clean cloth. Do not soak finished crystal
such as SWAROVSKI ELEMENTS Colors: Teak, Golden Shadow or
Silver Shade, for extended periods, as this may degrade the crystal's finish.
With the fixture untrimmed and turned off, wipe the frame, including the light bulbs once they are completely cool, with a soft
cloth.
Wearing white gloves, finger-cots or using a soft clean cloth, gently replace the trim as directed in the trim diagram.
P6
800.525.2655
WWW.ALLEGRICRYSTAL.COM
Loading...