Allegion Von Duprin 98 User Manual

98/99 Series

Exit devices

™

Introduction

Exit devices are a critical part of the ﬁre and life safety egress system and will provide safe and reliable service when properly applied and maintained. Von Duprin designs and manufactures exit devices in accordance to ISO 9001 Quality Management System and meets or exceeds accepted U.S. domestic and International standards. All 98 and 99 Series exit devices are UL listed for panic hardware or ﬁre hardware, and are certiﬁed to ANSI A156.3, 2001, Grade 1. Many models are also certiﬁed for Hurricane Resistant Applications. Consult your local Security & Safety consultant (SSC) or the Von Duprin factory for current listings.

It is intended that the information included in this publication, when properly used, will provide clear and reliable guidelines to the proper general selection and application. However, the scope of the information is necessarily limited.

98 Series features smooth mechanism case.

99 Series features grooved mechanism case.

Von Duprin exit devices are available in two external surface styles, designated 98 and 99 Series.

The Quiet One

A ﬂuid damper decelerates the pushpad on its return stroke and eliminates most noise associated with exit device operations. Furnished on all 98/99 exit devices.

VON DUPRIN

Administrative Oces 2720 Tobey Dr. Indianapolis, IN 46219

®

™

Series

Customer Service

877-671-7011 800-999-0328 - Fax

Latch bolt

Deadlocking latchbolt provides security and improved performance at standard device cost.

Technical Support

877-671-7011

2 • Von Duprin 98/99 Series

Table of contents

Exit hardware

Rim devices

98/99E 8

Trim 9

Fire exit hardware

Rim devices

98-F/99E-F 10

Trim 11

Mortise lock devices

875/9975 12

Trim 13

Surface mounted Vertical rod devices

9827/9927 16

Trim 17

Three-point latching devices

9857/9957 20

Trim 21

Concealed vertical rod devices

9847/9947 24

Trim 25

9848/9948 28

Trim 29

Concealed vertical cable devices

9849/9949 32

Trim 33

Wood door concealed vertical rod devices

9847WDC/9947WDC 36

Trim 37

Wood door concealed vertical cable devices

9849WDC/9949WDC 40

Trim 41

Mortise lock devices

9875-F/9975-F 14

Trim 15

Surface mounted Vertical rod devices

9827-F/9927-F 18

Trim 19

Three-point latching devices

9857- F/9957-F 22

Trim 23

Concealed vertical rod devices

9847-F/9947-F 26

Trim 27

9848-F/9948-F 30

Trim 31

Concealed vertical cable devices

9849-F/9949-F 34

Trim 35

Wood door concealed vertical rod devices

9847WDC-F/9947WDC-F 38

Trim 39

Wood door concealed vertical cable devices

9849WDC-F/9949WDC-F 42

Trim 43

Be sure to ask your SSC representative to tell you about Custom Solutions

by Ingersoll Rand Security Technologies. To learn more visit securitytechnologies.allegion.com.

Von Duprin 98/99 Series • 3

Options and accessories

Applications & trim operation

Single & double door applications Door handing outside trim operation Lever styles

Tri m options

Knob Thumbpiece Lever Electriﬁed outside lever trim (E996L) Breakaway lever Thumbturn control Hospital pull Offset pull Vandal resistant pull AD-Series adaptable electronic trim

Strike options

Dogging options

Strike/Stile information Strikes

Cylinder dogging Hex key dogging Less dogging Dogging keys Special center case dogging Double cylinder

Symbols

Indicates ﬁre rated application Indicates ADA products

Electrical options

Electrical accessories

Mechanical options

Pneumatic options

Device accessories

RX Request to exit LX Latchbolt monitoring SS Signal switch CX Chexit

®

ALK Alarm kit Electric mortise lock device

EL Electric latch retraction QEL Quiet electric latch retraction CON Allegion Connect

Power supplies Electric power transfer

XP98/99 rim exit device WS Surface vertical rod exit device Less bottom rod AX Accessible device Pullman latch Dummy push pad Braille, embossed, knurled and safety glow (Luminescent) touchpads

Pneumatic controlled exit devices Pneumatic power transfer

Glass bead kit Vertical rod and latch guard Cover plate kits Cylinders Mullions Sex bolts

Additional information

Finishes

ANSI Function, grade & type Ul ﬁre labeling and opening size

Standard & special ﬁnishes

4 • Von Duprin 98/99 Series

Nomenclature – how to order

None SD CD

CX E QEL EL LX RX RX2 SS AX

PL PN WS XP

WS Tornado & hurricane tested

98 99

None 27 47 47WDC 48 49 49WDC 57 75

XX DT EO HL K K-B E K-D T K-NL L L-BE L-DT L-NL NL NL-OP TL TL-BE TP TP-BE

Standard Special dogging R/ VR - panic only Cylinder dogging - panic only

Chexit Electric locking mortise/lever Quiet electric latch retraction Electric latch retraction Latch bolt monitoring Request to exit Double request to exit Signal switch Accessible device

Pullman latch Pneumatic latch retraction Surface vertical rod exit device Heavy protection - rim

Series 98-smooth Series 99-grooved

Rim device Surface mounted vertical rod device Concealed vertical rod device Concealed vertical rod wood door device Concealed vertical rod device Concealed vertical cable device Concealed vertical cable wood door device Three-point latch device Mortise lock device

AD Trim (to come from client) Dummy trim Exit only Hospital pull trim Knob Knob - blank escutcheon Knob, rigid - dummy trim Knob, rigid - night latch Lever (classroom) Lever - blank escutcheon Lever, rigid - dummy trim Lever, rigid - night latch Night latch Night latch cylinder assembly, optional pull Turn lever Turn lever - blank escutcheon Thumbpiece Thumbpiece - blank escutcheon

EL 99 27 -L -16 -F LBR 3' US3 RHR

XX Lever style 06 standard

F Fire exit device

-2 Double cylinder (rim & mortise only) LBR

LBL SG ALK ALK-AR1 ALK-AR3 ALK-AR6 CON

2' 3' 4'

Finishes

-LHR

-RHR

Optional 01, 02, 03, 05, 07, 12 (Handed), 16 (Omega), 17, 18, Accent, Asti, Merano, St. Annes

Less bottom rod Less bottom latch Safety glow (luminescent) touchpad Alarm kit Auto-reset 1 Auto-reset 3 minute alarm kit Auto-reset 4 1/2 minute alarm kit Allegion Connect

2' Device (2' door size) 27, 47 or 49 only 3' Device (2' 4"– 3' door size) 4' Device (2' 10"– 4' door size)

US3, US4, US10, US26, US26D, US28, 313, 315 US32D – 98 ONLY

-AM Antimicrobial (available US26D and US32D)

Le hand reverse Right hand reverse

1

/2 minute alarm kit

Von Duprin 98/99 Series • 5

Popular double door applications

Left Hand-Reverse Orientation

LHR

RHR

Right Hand-Reverse

Orientation

Single door applications

Single mortise lock device

Single rim device

Door handing

Le hand-reverse orientation

(Le hand-reverse) (Right hand-reverse)

Right hand-reverse orientation

Outside

Double door applications

Mortise lock and surface mounted or concealed vertical cable/rod device combination—same direction

Two surface mounted vertical rod devices—same direction (do not use with overlapping astragal)

Two rim devices with mullion— same direction

Two ﬁre exit hardware vertical cables/rods with auxilary ﬁre latch-LBR option

Two vertical rods—double egress

Two concealed vertical cables/rods

Outside trim operation

Trim operation lever or knob

Standard Blank escutcheonNight latch Dummy

Key locks and unlocks lever or knob. e.g., 996L (Classroom)

996L Breakaway

Key retracts latch bolt. Lever or knob is rigid. Use NL sux, e.g. 996LNL. (Storeroom)

™

lever

The 996L Breakaway trim has become the standard lever trim offering on the 98L/99L Series devices. The Breakaway design is especially effective in areas where vandalism to door hardware is a problem. The design intent is to discourage costly repairs from becoming necessary. The Breakaway feature is not available on the NL (night-latch) or DT (dummy trim) versions.

Lever or knob always active. Use BE sux, e.g., 996L-BE. (Passage)

Lever or knob rigid for pull operation. Use DT sux, e.g., 996L-DT.

374T/376T Series thumbturn control

Standard operation, key locks and unlocks thumbturn. Optional operation, key unlocks thumbturn, re-locks when key is removed. This operation is created by changing the cylinder plate included with control. Use 1 cylinder with a straight cam. Schlage cam reference B502-191. Use with a pull trim (990DT pictured).

1

/4" mortise

6 • Von Duprin 98/99 Series

Lever styles

Decorative levers

M51

Knurling available

M56 M57 •• M61

M81

Knurling available

M52 Knurling available

M82 M83 M84 M85

M53 M54 M55

(Handed)

Standard Levers

M62 ••

(Handed)

•• Available in Stainless Steel substrate ONLY.

M63

(Handed)

01 02

07 12

ACC (Accent) (Handed)

LON* Longitude

Knurling available

(Handed)

AST (Asti) (Handed)

03* Knurling available

16 (Omega)

MER (Merano) (Handed)

05 06*

17* Knurling available

STA (St. Annes) (Handed)

*Available in Stainless Steel - specify SS when ordering

Default lever Knurling available

18

LAT * Latitude

Von Duprin 98/99 Series • 7

98/99 Rim exit device

The 299 Strike ships standard, optional strikes available

98/99 Rim exit device

98 and 99 Rim exit devices for all types of single and double doors with mullion, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 98 device has a smooth mechanism case and the 99 device has a grooved case. The rim device is non-handed except when the following device options are used: SD (special dogging), -2 (double cylinder) or SS (signal switch). See Opposite page for available outside trim and device functions. Covers stock hollow metal doors with 86 or 161 cutouts on single doors (may cover cutouts on pairs – consult template).

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions

Device lengths

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection

Latch bolt

Fasteners & sex bolts (SNB)

Electric options

Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device.

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

13

39

/16" (1011 mm)

11

39

/16" (1008 mm) with mullion

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar neutral – 3 Pushbar depressed – 3

Deadlocking,

Includes screw pack for 1

13

/16" (97 mm)

1

/16" (78 mm)

3

/4" (19mm) throw

3

/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available, see page 9 for quantities.

LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric locking & unlocking trim EL Electric latch retraction

XP

Extra protection

• 90˚ latch-tostrike contact

• Force resistance of 2,000+ lbs.

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

QEL Quiet electric latch retraction SS Signal switch

Mechanical options

CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect

-2 Double cylinder AX Accessible device GBK Glass bead kit

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

PN Pneumatic latch retraction

Dogging feature

Dogging options

Strikes

XP Extra protection SNB Sex bolts SEC Security screws

Hex key dogging standard

CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator

299 – Dull black

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

Hex key dogging comes standard on 98/99 Rim exit devices

CD

Cylinder dogging

• Replaces hex key dogging

• Requires standard 1

1

/4"

mortise cylinder

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

AX

Accessible device

• UL certiﬁed to meet new 5 lb. maximum operating force requirement

• Exceeds ANSI/ BHMA requirements

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

8 • Von Duprin 98/99 Series

Standard trim

EO

DT NL NL-OP

No outside trim

Exit only

Product description 98EO

99EO

Trim description

Escutcheon plate size

— 990DT 990NL-R/V

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) —

Dummy trim

Pull when dogged

98DT 99DT

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) —

Night latch

Key retracts latchbolt

98NL 99NL

13

3" x 14

/16" x 3/32"

(76x360x2mm)

Night latch

Key retracts latchbolt optional pull required

98NL-OP 99NL-OP

110NL-MD 110NL-WD

—

ANSI function 01 02 03 03

Cylinder type

Handing

Optional trim x990EO

Optional #425 SNB quantity for device

— — Rim Rim

— — — —

x996K-NL x996L-NL x696NL x697NL

x996EO

x996K-DT x996L-DT x696DT x697DT

6 2 2 6

L L-NL L-BE L-DT

98/99 Rim exit device

Lever

Key locks & unlocks

Product description 98L

99L

Lever – night latch

Key retracts latchbolt

98L-NL 99L-NL

Lever – blank escutcheon

Always operable (no cylinder)

98L-BE 99L-BE

Lever dummy trim

pull when dogged

98L-DT 99L-DT

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 9

98-F/99-F Rim exit device

98-F and 99-F Rim ﬁre exit devices for all types of single doors up to 4' x 10' (1219mm x 3048mm) or 8' x 10' (2438mm x 3048mm) double doors with 9954 or 9854 mullion, UL listed for ﬁre exit hardware. See page 61 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 98-F device has a smooth mechanism case and the 99-F device has a grooved case. The rim device is non-handed except when the following device options are used: -2 (double cylinder) or SS (signal switch). See opposite page for available outside trim and device functions.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

The 299F Strike ships standard, optional strikes available

499F Strike with 9854/9954 mullion

98-F/99-F Rim exit device

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 3' 2'4' to 3' (711mm to 914 mm) Door size

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection Pushbar neutral – 3

Latch bolt Deadlocking,

Fasteners & sex bolts (SNB)

Electric options LX Latchbolt monitor switch

Mechanical options

Dogging option No mechanical dogging. EL and QEL option available Strikes 299F – Dull black, 499F with mullions

NL drive screw from device.

4' 2'10" to 4' (864 mm to 1219 mm) Door size

13

39

/16" (1011 mm)

11

39

/16" (1008 mm) with mullion

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

13

/16" (97 mm)

Pushbar depressed – 3

3

/4" (19mm) throw

Includes screw pack for 1

1

/16" (78 mm)

3

/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available for metal doors. 425 & 825 SNB required on wood doors without SLM blocking. See page 11 for quantities.

RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric locking & unlocking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect

-2 Double cylinder AX Accessible device GBK Glass bead kit PN Pneumatic latch retraction XP Extra protection SNB Sex bolts SEC Security screws SLM Special Laminate Material Blocking

XP

Extra protection

• 90˚ latch-tostrike contact

• Force resistance of 2,000+ lbs.

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

AX

Accessible device

• UL certiﬁed to meet new 5 lb. maximum operating force requirement

• Exceeds ANSI/ BHMA requirements

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

SG

Safety glow

• Shows exit door location in darkness or smoke

• Developed to meet MEA standards

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

10 • Von Duprin 98/99 Series

Standard trim

EO

DT NL NL-OP

No outside trim

Exit only

Product description 98EO-F

99EO-F

Trim description

Escutcheon plate size

— 990DT 990NL-R/V

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) —

Dummy trim

Pull when dogged (not recommended for ﬁre device)

98DT-F 99DT-F

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) —

Night latch

Key retracts latchbolt

98NL-F 99NL-F

13

3" x 14

/16" x 3/32"

(76x360x2mm)

Night latch

Key retracts latchbolt optional pull required

98NL-OP-F 99NL-OP-F

110NL-MD 110NL-WD

—

ANSI function 01 02 03 03

Cylinder type

Handing

Optional trim x990EO

— — Rim Rim

— — — —

x996K-NL x996L-NL x696NL x697NL

x996EO

x996K-DT x996L-DT x696DT x697DT

#425 SNB optional

- HMD req. WD w/o

2 2 2 2

SLM pkg.

#825 SNB req. WD w/o SLM pkg.

#425 SNB req. w/ 499F

2 (if using trim) 2 2 2

2 2 2 2

98-F/99-F Rim exit device

L L-NL L-BE L-DT

Lever

Key locks & unlocks

Product description 98L-F

99L-F

Lever – night latch

Key retracts latchbolt

98L-NL-F 99L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

98L-BE-F 99L-BE-F

Lever dummy trim

pull when dogged (not recommended for ﬁre device)

98L-DT-F 99L-DT-F

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

#425 SNB optional

- HMD req. WD w/o

2 2 2 2

SLM pkg.

#825 SNB req. WD w/o SLM pkg.

#425 SNB req. w/ 499F

* Electriﬁed lever operation available

2 (if using trim) 2 2 2

2 2 2 2

Von Duprin 98/99 Series • 11

9875/9975 Mortise lock device

9875/9975 Mortise lock device for all types of single or double doors, UL listed for Panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Fits stock hollow metal doors with 86 cutout and door stiles as narrow as 4

3

/4" (121mm). The 9875 device has a smooth mechanism case and the 9975 device has a grooved case. The mortise lock device is non-handed except when the following device options are used: -2 (double cylinder) or SS (signal switch). See opposite page for available outside trim and device functions.

The 7500 Mortise lock is equipped with a

3

/4" (19mm) anti-friction latch bolt which is ﬁeld reversible without removing the lock from the door. It has a non-handed auxiliary bolt for deadlocking and a faceplate with an adjustable bevel.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 3' 2'4' to 3' (711mm to 914 mm) Door size

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection Pushbar neutral – 3

Fasteners & sex bolts (SNB)

Electric options RX Pushpad monitor switch

NL drive screw from device.

4' 2'10" to 4' (864 mm to 1219 mm) Door size

13

39

/16" (1011 mm)

11

39

/16" (1008 mm) with mullion

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

13

/16" (97 mm)

Pushbar depressed – 3

Includes screw pack for 1

1

/16" (78 mm)

3

/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available, see page 13 for quantities.

RX2 Double pushpad monitor switch E Electric locking & unlocking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

CX Chexit delayed exit

Mechanical options

ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect

-2 Double cylinder GBK Glass bead kit PN Pneumatic latch retraction SNB Sex bolts

E (E7500)

Electric mortise lock device

• Remains latched while unlocked

• Remote electrical control

SEC Security screws

Dogging feature Hex key dogging standard Dogging option CD Cylinder dogging

SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator

Strikes 575 – Dull Black

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

7500 Mortise Lock

Hex key dogging comes standard on

9875/9975 Mortise Lock Devices

575 Strike

CD

Cylinder dogging

• Replaces hex key dogging

• Requires standard 1

1

/4"

mortise cylinder

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

SS 7500

Signal switch

• Signals unauthorized use of an opening

• Switch makes latch bolt tamper-resistant

12 • Von Duprin 98/99 Series

Standard trim

EO

DT NL HL

No outside trim

Exit only

Product description 9875EO

9975EO

Dummy trim

Pull when dogged (not recommended for ﬁre device)

9875DT 9975DT

Night latch

Key retracts latchbolt

9875NL

9975NL

Hospital latch

Key locks & unlocks

9875HL

9975HL

Trim description — 990DT 990NL-M HL6M

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) 2

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) –

3" x 14 3/16" x 3/32" (76x360x2mm)

2 9/16" x 5 1/2" x 2 5/8" (65x140x67mm)

5

/8" (67mm)

3

3" x 14

ANSI function 01 02 03 —

Cylinder type

— — 1

1

/4" Mortise 1 1/4" Mortise

Handing

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 2

x996K-DT x996L-DT) x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

L L-NL L-BE L-DT

9875/9975 Mortise lock device

Lever

Key locks & unlocks

Product description 9875L

9975L

Lever – night latch

Key retracts latchbolt

9875L-NL 9975L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9875L-BE 9975L-BE

Lever dummy trim

pull when dogged

9875L-DT 9975L-DT

Trim description 996L-M* 996L-NL-M 996L-BE-M* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

1

/4" Mortise 1 1/4" Mortise — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 13

9875-F/9975-F Mortise lock ﬁre exit device

9875-F/9975-F Fire exit mortise lock devices for all types of single doors up to 4' x 10' (1219mm x 3048mm) or 8' x 10' (2438mm x 3048mm) double doors installations, UL listed for ﬁre exit hardware; See page 61 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. Fits door stiles as narrow as 4

3

/4" (121mm). The 9875-F device has a smooth mechanism case and the 9975-F device has a grooved case. The mortise lock device is non-handed except when the following device options are used: -2 (double cylinder) or SS (signal switch) devices. See opposite page for available outside trim and functions.

The 7500 Mortise lock is equipped with

3

/4" (19mm) anti-friction latch bolt which is ﬁeld reversible without removing the lock from the door. It has a non-handed auxiliary bolt for deadlocking and a faceplate with an adjustable bevel.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 3' 2'4' to 3' (711mm to 914 mm) Door size

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection Pushbar neutral – 3

Fasteners & sex bolts (SNB)

Electric options RX Pushpad monitor switch

NL drive screw.

4' 2'10" to 4' (864 mm to 1219 mm) Door size

13

39

/16" (1011 mm)

11

39

/16" (1008 mm) with mullion

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

13

/16" (97 mm)

Pushbar depressed – 3

Includes screw pack for 1

1

/16" (78 mm)

3

/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors. Optional 425 SNB available for metal doors. 425 & 825 SNB required on wood doors without SLM blocking. See page 11 for quantities.

RX2 Double pushpad monitor switch E Electric locking & unlocking trim EL Electric latch retraction

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL Quiet electric latch retraction SS Signal switch

Mechanical options

CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect

-2 Double cylinder GBK Glass bead kit PN Pneumatic latch retraction

E (E7500)

Electric mortise lock device

• Remains latched while unlocked

• Remote electrical control

SNB Sex bolts SEC Security screws SLM Special Laminate Material Blocking

Dogging option No Mechanical Dogging. EL and QEL option available Strikes 575 – Dull Black

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

7500 Mortise Lock

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

SG

Safety glow

• Shows exit door location in darkness or smoke

• Developed to meet MEA standards

SS 7500

Signal switch

• Signals unauthorized use of an opening

• Switch makes latch bolt tamper-resistant

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

575 Strike

14 • Von Duprin 98/99 Series

Standard trim

EO

DT NL HL

No outside trim

Exit only

Product description 9875EO-F

9975EO-F

Dummy trim

Pull when dogged (not recommended for ﬁre device)

— —

Night latch

Key retracts latchbolt

9875NL-F 9975NL-F

Hospital latch

Key locks & unlocks

9875HL-F 9975HL-F

Trim description — 990DT 990NL-M HL6M

3

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) 2

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) –

3" x 14 3/16" x 3/32" (76x360x2mm)

2 9/16" x 5 1/2" x 2 5/8" (65x140x67mm)

5

/8" (67mm)

ANSI function 01 02 03 —

Cylinder type

— — 1

1

/4" Mortise 1 1/4" Mortise

Handing

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 2

x996K-DT x996L-DT) x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

L L-NL L-BE L-DT

9875-F/9975-F Mortise lock ﬁre exit device

Lever

Key locks & unlocks

Product description 9875L-F

9975L-F

Lever – night latch

Key retracts latchbolt

9875L-NL-F 9975L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9875L-BE-F 9975L-BE-F

Lever dummy trim

pull when dogged (not recommended for ﬁre device)

— —

Trim description 996L-M* 996L-NL-M 996L-BE-M* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

1

/4" Mortise 1 1/4" Mortise — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 15

9827/9927 Surface mounted vertical rod device

9827/9927 Surface mounted vertical rod device for all types of single or double doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The 9827 device has a smooth mechanism case and the 9927 device has a grooved case. The surface vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions.Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 2' 2" (610 mm) Door size (shipped less UL label)

Device centerline from ﬁnished ﬂoor Center case dimensions Mechanism case dimensions Projection Pushbar neutral – 3

Latch bolt Deadlocking anti-friction top & bottom bolt,

Door undercut

Top & bottom Latch case Vertical rods

Fasteners & sex bolts (SNB)

Electric options LX Latchbolt monitor switch

9827/9927 Surface mounted vertical rod device

Mechanical options

Dogging feature Hex key dogging standard Dogging option CD Cylinder dogging

Strikes Top - 299 – Dull black, Bottom – 248L4 & 304L - Unﬁnished

16 • Von Duprin 98/99 Series

NL drive screw from device.

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm)

3

8" x 2

/4" x2 3/8" (203mm x 70mm x 60mm)

1

2

/4" x 2 1/4" (57mm x 57mm)

13

/16" (97 mm)

Pushbar depressed – 3

1

/4" (7mm) recommended

1

/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)

4

1

/2" square tubing, standard rods accommodate 7' (2134mm)

doors. Top rod length: 34

1

31

/2" (794mm) Extension rods available in 1' (205mm) or 3'

1

/16" (78 mm)

5

/8" (16mm) throw

15

/16" (887mm); Bottom rod length:

(914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 1

3

/4" (44mm) to 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available.

RX Pushpad monitor switch RX2 Double pushpad monitor switch EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit PN Pneumatic latch retraction LBR Less bottom rod WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PL Pullman latch WS Tornado and hurricane tested SNB Sex bolts SEC Security screws

SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator

WS

Windstorm

• Severe weather certiﬁed/tested

• FEMA and ICC compliant

• Tornado & hurricane tested

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

299 Top strike

248L4 Bottom Strike for use with

ﬂat threshold

304L Bottom strike

Hex key dogging comes

standard on 9827/9927

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

SS

Signal switch

• Signals unauthorized use of an opening

• Switch makes latch bolt tamper-resistant

Top latch

Bottom latch

Standard trim

EO

No outside trim

Exit only

Product description 9827EO

9927EO

Trim description

Escutcheon plate size

— 990DT 990NL-R/V

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 3

DT NL NL-OP TL TL-BE

Dummy trim

Pull when dogged

9827DT 9927DT

Night latch

Key retracts latchbolt

9827NL 9927NL

Night latch

Key retracts latchbolt optional pull required

9827NL-OP 9927NL-OP

110NL-MD 110NL-WD

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

—

Thumbturn Key locks & unlocks (use with DT trim)

9827TL 9927TL

374T X 990DT

11

1

/16" x 7 1/2" x 7/8"

(43x191x22mm)

1

/4" (83mm) 3 1/4" (83mm)

ANSI function 01 02 03 03 11 or 12 16

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 6 2 2

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9827TL-BE 9927TL-BE

374T-BE X 990DT

11

1

/16" x 7 1/2" x 7/8"

(43x191x22mm)

9827/9927 Surface mounted vertical rod device

L L-NL L-BE L-DT

Lever

Key locks & unlocks

Product description 9827L

9927L

Lever – night latch

Key retracts latchbolt

9827L-NL 9927L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9827L-BE 9927L-BE

Lever dummy trim

pull when dogged

9827L-DT 9927L-DT

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 17

9827/9927 Surface mounted vertical rod device

9827-F/9927-F Surface Mounted Vertical Rod Fire Device

9827-F/9927-F Fire exit surface mounted vertical rod device pairs of doors up to 8' x 10' (2438mm x 3048mm) , UL listed for ﬁre exit hardware. See page 68 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9827-F device has a smooth mechanism case and the 9927-F device has a grooved case. The surface vertical rod device is non-handed except when the following device options are used: SS (signal switch). See opposite page for available outside trim and device functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors. Rod and latch guards can be used on hollow metal or tin clad composite ﬁre doors.

Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 2' 2" (610 mm) Door size (shipped less UL label)

Device centerline from ﬁnished ﬂoor Center case dimensions Mechanism case dimensions Projection Pushbar neutral – 3

Latch bolt Deadlocking anti-friction top & bottom bolt,

Door undercut

Top & bottom Latch case Vertical rods

Fasteners & sex bolts (SNB)

Electric options LX Latchbolt monitor switch

Mechanical options

Dogging option No mechanical dogging. EL and QEL option available Strikes Top – 299F (499F LBR) Dull black, Bottom – 304L - Unﬁnished

NL drive screw from device.

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

/8" (1006 mm)

39

3

8" x 2

/4" x2 3/8" (203mm x 70mm x 60mm)

1

2

/4" x 2 1/4" (57mm x 57mm)

13

/16" (97 mm)

1

Pushbar depressed – 3

1

/4" (7mm) recommended

1

/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)

4

1

/2" square tubing, standard rods accommodate 7' (2134mm)

doors. Top rod length: 34

1

/2" (794mm) Extension rods available in 1' (205mm) or 3'

31

/16" (78 mm)

5

/8" (16mm) throw

15

/16" (887mm); Bottom rod length:

(914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 1

3

/4" (44mm) to 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available.

RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction LBR Less bottom rod PL Pullman latch WS Tornado and hurricane tested SNB Sex bolts SEC Security screws SLM Special laminate material blocking

WS

Windstorm

• Severe weather certiﬁed/tested

• FEMA and ICC compliant

• Tornado & hurricane tested

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

299 Top strike

499F

Top strike - LBR

304L Bottom strike

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

LBR

Less bottom rod

• Available with UL Fire Label

• For pairs of vertical rod devices

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

Top latch

Bottom latch

18 • Von Duprin 98/99 Series

Standard trim

EO

DT NL NL-OP TL TL-BE

Dummy trim

No outside trim

Exit only

Product description 9827EO-F

9927EO-F

Trim description

Escutcheon plate size

— 990DT 990NL-R/V

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm)

Pull when dogged (not recommended for ﬁre device)

— —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

Night latch

Key retracts latchbolt

9827NL-F 9927NL-F

13

3" x 14

/16" x 3/32"

(76x360x2mm)

Night latch

Key retracts latchbolt optional pull required

9827NL-OP-F 9927NL-OP-F

110NL-MD 110NL-WD

—

Thumbturn Key locks & unlocks (use with DT trim)

9827TL-F 9927TL-F

374T X 990DT

11

1

/16" x 7 1/2" x 7/8"

(43x191x22mm)

ANSI function 01 02 03 03 11 or 12 16

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 6 2 2

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

L L-NL L-BE L-DT

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9827TL-BE-F 9927TL-BE-F

374T-BE X 990DT

11

1

/16" x 7 1/2" x 7/8"

(43x191x22mm)

9827/9927 Surface mounted vertical rod device

Lever

Key locks & unlocks

Product description 9827L-F

9927L-F

Lever – night latch

Key retracts latchbolt

9827L-NL-F 9927L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9827L-BE-F 9927L-BE-F

Lever dummy trim

pull when dogged (not recommended for ﬁre device)

— —

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 19

9857/9957 Three-point latching device

9857/9957 Three-point latching device for all types of single or double doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or 161 cutouts. The 9857 device has a smooth mechanism case and the 9957 device has a grooved case. The three-point latching device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 3' 2'4' to 3' (711mm to 914 mm) Door size

Device centerline from ﬁnished ﬂoor Center case dimensions Mechanism case dimensions Projection Pushbar neutral – 3

Latch bolt Deadlocking anti-friction top & bottom bolt,

Door undercut

Top & bottom Latch case Vertical rods

Fasteners & sex bolts (SNB)

Electric options LX Latchbolt monitor switch

9857/9957 Three-point latching device

Mechanical options

Dogging feature Hex key dogging standard Dogging option CD Cylinder dogging

Strikes Top & middle – 299 - Dull black

20 • Von Duprin 98/99 Series

NL drive screw from device.

4' 2'10" to 4' (864 mm to 1219 mm) Door size

13

/16" (1011 mm)

39

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

/4" x 2 1/4" (57mm x 57mm)

2

13

/16" (97 mm)

1

Pushbar depressed – 3

Deadlocking rim bolt,

1

/4" (7mm) recommended

1

/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)

4

1

/2" square tubing, standard rods accommodate 7' (2134mm)

doors. Top rod length: 34

1

/2" (794mm) Extension rods available in 1' (205mm) or 3'

31

/16" (78 mm)

5

3

/4" (19mm) throw

15

/16" (887mm); Bottom rod length:

/8" (16mm) throw

(914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 1

3

/4" (44mm) to 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available.

RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction PL Pullman latch WS Tornado and hurricane tested SNB Sex bolts SEC Security screws

SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator

Bottom – 248L4 & 304L - Unﬁnished

WS

Windstorm

• Severe weather certiﬁed/tested

• FEMA and ICC compliant

• Tornado & hurricane tested

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

299 Top & middle strike

248L4 Bottom Strike for use with

ﬂat threshold

304L Bottom strike

Hex key dogging comes

standard on 9857/9957 Three-point latching devices

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

SS

Signal switch

• Signals unauthorized use of an opening

• Switch makes latch bolt tamper-resistant

Top latch

Bottom latch

Standard trim

EO

DT NL NL-OP TL TL-BE

Dummy trim

No outside trim

Exit only

Product description 9857EO

9957EO

Trim description

Escutcheon plate size

— 990DT 990NL-R/V

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm)

Pull when dogged (not recommended for ﬁre device)

9857DT 9957DT

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

Night latch

Key retracts latchbolt

9857NL 9957NL

13

3" x 14

/16" x 3/32"

(76x360x2mm)

Night latch

Key retracts latchbolt optional pull required

9857NL-OP 9957NL-OP

110NL-MD 110NL-WD

—

Thumbturn Key locks & unlocks (use with DT trim)

9857TL 9957TL

9857TL-BE 9957TL-BE

374T X 990DT 374T-BE X 990DT

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

ANSI function 01 02 03 03 11 or 12 16

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 6 2 2

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

L L-NL L-BE L-DT

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9857/9957 Three-point latching device

Lever

Key locks & unlocks

Product description 9857L

9957LF

Lever – night latch

Key retracts latchbolt

9857L-NL 9957L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9857L-BE 9957L-BE

Lever dummy trim

pull when dogged

— —

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 21

9857-F/9957-F Three-point latching ﬁre exit device

299 Top & middle strike

Top latch

9857-F/9957-F Three-point latching ﬁre exit device

9857-F/9957-F Fire exit three-point latching device for all types of single doors up to 4' x 8' (1219mm x 2438mm) or up to 8' x 8'(2438mm x 2438mm) double doors with 9954 or 9854 mullion, UL listed for ﬁre exit hardware. See page 68 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9857-F device has a smooth mechanism case and the 9957-F device has a grooved case. The three-point latch device is non-handed except when the following device option is used: SS (signal switch). See opposite page for available outside trim and device functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device from damage by impacts of carts or gurneys passing through doors.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions

Device lengths

Device centerline from ﬁnished ﬂoor Center case dimensions Mechanism case dimensions Projection

Latch bolt

Door undercut

Top & bottom Latch case Vertical rods

Fasteners & sex bolts (SNB)

Electric options

Mechanical options

Dogging option Strikes

Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

13

/16" (1011 mm)

39

3

8" x 2

/4" x2 3/8" (203mm x 70mm x 60mm)

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar neutral – 3 Pushbar depressed – 3

Deadlocking anti-friction top & bottom bolt, Deadlocking rim bolt,

1

/4" (7mm) recommended

1

/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)

4

1

/2" square tubing, standard rods accommodate 7' (2134mm)

doors. Top rod length: 34

1

/2" (794mm) Extension rods available in 1' (205mm) or 3'

31

13

/16" (97 mm)

1

/16" (78 mm)

5

3

/4" (19mm) throw

15

/16" (887mm); Bottom rod length:

/8" (16mm) throw

(914mm) for doors over 7'. One piece top rod is available for 8' (2438mm) and 10' (3048mm) doors. Includes screw pack for 1

3

/4" (44mm) and 2 1/4" (57mm) thick metal or wood doors, and 325 SNB for top and bottom latch. Optional 425 SNB available for metal doors. 425 SNB required on wood doors without SLM blocking.

LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction SNB Sex bolts SEC Security screws SLM Special laminate material blocking

No mechanical dogging. EL and QEL option available Top & middle – 299 - Dull black Bottom – 304L - Unﬁnished

PN

Pneumatic latch retraction

• For areas where

• Special linkage

EL

Electric latch retraction

• Enables remote

• Alternative to

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote

• Standard in fail

RX

Pushpad monitor switch

• Signals use of an

• SPDT switch to

ALK

Alarm exit kit

• Unauthorized

• Set in armed or

304L Bottom strike

499F Rim Strike

for Mullion Applications

electrical devices banned

for mechanical or pneumatic dogging

unlatching

manual dogging

locking/unlocking

safe condition

opening

monitor pushpad

opening triggers 85-decibel horn

disarmed mode by key

Bottom latch

RG

Rod guard

• Protection from carts/gurneys

• Eases wheelchair access

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

22 • Von Duprin 98/99 Series

Standard trim

EO

DT NL NL-OP TL TL-BE

Dummy trim

No outside trim

Exit only

Product description 9857EO-F

9957EO-F

Trim description

Escutcheon plate size

— 990DT 990NL-R/V

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm)

Pull when dogged (not recommended for ﬁre device)

9857DT-F 9957DT-F

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

Night latch

Key retracts latchbolt

9857NL-F 9957NL-F

13

3" x 14

/16" x 3/32"

(76x360x2mm)

Night latch

Key retracts latchbolt optional pull required

9857NL-OP-F 9957NL-OP-F

110NL-MD 110NL-WD

—

Thumbturn Key locks & unlocks (use with DT trim)

9857TL-F 9957TL-F

9857TL-BE-F 9957TL-BE-F

374T X 990DT 374T-BE X 990DT

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

ANSI function 01 02 03 03 11 or 12 16

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

#425 SNB optional

- HMD req. WD

6 2 2 6 2 2

w/o SLM pkg.

#425 SNB req. w/ 499F

2 2 2 2

L L-NL L-BE L-DT

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9857-F/9957-F Three-point latching ﬁre exit device

Lever

Key locks & unlocks

Product description 9857L-F

9957L-F

Lever – night latch

Key retracts latchbolt

9857L-NL-F 9957L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9857L-BE-F 9957L-BE-F

Lever dummy trim

pull when dogged

— —

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

#425 SNB optional

- HMD req. WD

2 2 2 2

w/o SLM pkg.

#425 SNB req. w/ 499F

* Electriﬁed lever operation available

2 2 2 2

Notes

Von Duprin 98/99 Series • 23

9847/9947 Concealed vertical rod device

9847/9947 Concealed vertical rod device for use on single or double metal doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847 device has a smooth mechanism case and the 9947 device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and device functions.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

338

Top Strike

385A

Bottom Strike

Top Latch

Bottom Latch

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 2' 2" (610 mm) Door size (shipped less UL label)

Device centerline from ﬁnished ﬂoor Center case dimensions Mechanism case dimensions Projection Pushbar neutral – 3

Latch bolt Deadlocking top & bottom bolt,

Door undercut

Top & bottom Latch case Vertical rods Round 2-piece adjustable rods – Top rod adjustable from 6'8"

Fasteners & sex bolts (SNB)

Electric options LX Latchbolt monitor switch

9847/9947 Concealed vertical rod device

Mechanical options

Dogging feature Hex key dogging standard Dogging option CD Cylinder dogging

Strikes Top – 338 - Unﬁnished, Bottom – 385A - Unﬁnished

24 • Von Duprin 98/99 Series

NL drive screw from device.

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

/8" (1006 mm) Standard

39 Adjustable from 35

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar depressed – 3

1

/4" (7mm) recommended

1

/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)

4

(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 (905 mm) to 49 doors over 8'4" (2533mm). Includes screw pack for 1

5

/8" (905mm) to 495/8" (1260mm)

13

/16" (97 mm)

1

/16" (78 mm)

5

/8" (16mm) throw

5

/8" (1260 mm). Extension rod kits available for

3

/4" (44mm) to 2 1/4" (57mm) thick

metal doors. Optional 425 SNB available.

RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction LBR Less bottom rod PL Pullman latch SNB Sex bolts SEC Security screws

SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator

5

/8"

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

Hex key dogging comes standard on 9847/9947 Concealed vertical rod devices

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

DI

Dogging indicator

• Monitor dogging status without a control panel

• Red indicator light shows visibility to dogging from over 75 feet

Standard trim

EO

DT NL NL-OP TL TL-BE

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9847TL-BE 9947TL-BE

No outside trim

Exit only

Product description 9847EO

9947EO

Dummy trim

Pull when dogged (not recommended for ﬁre device)

9847DT 9947DT

Night latch

Key retracts latchbolt

9847NL 9947NL

Night latch

Key retracts latchbolt optional pull required

9847NL-OP 9947NL-OP

Thumbturn Key locks & unlocks (use with DT trim)

9847TL 9947TL

Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm)

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

3

2

—

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

ANSI function 01 02 03 03 11 or 12 16

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 6 2 2

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

L L-NL L-BE L-DT

9847/9947 Concealed vertical rod device

Lever

Key locks & unlocks

Product description 9847L

9947LF

Lever – night latch

Key retracts latchbolt

9847L-NL 9947L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9847L-BE 9947L-BE

Lever dummy trim

pull when dogged

9847L-DT 9947L-DT

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 25

9847-F/9947-F Concealed vertical rod ﬁre exit device

9847-F/9947-F Fire exit concealed vertical rod device for use on pairs of doors up to 8' x 10' (2438mm x 3048mm) , UL listed for ﬁre exit hardware. See page 68 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9847-F device has a smooth mechanism case and the 9947-F device has a grooved case. The concealed vertical rod device is non-handed except when the following device option is used: SS (signal switch) devices. See opposite page for available outside trim and functions.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

338

Top Strike

385A

Bottom Strike

Top Latch

Bottom Latch

9847-F/9947-F Concealed vertical rod ﬁre exit device

Speciﬁcations

Device functions

Device lengths

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection

Latch bolt

Door undercut

Top & bottom Latch case

Vertical rods

Fasteners & sex bolts (SNB)

Electric options

Mechanical options

Dogging option No mechanical dogging. EL and QEL option available Strikes

Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm) Standard

Adjustable from 35

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar neutral – 3 Pushbar depressed – 3

Deadlocking top & bottom bolt,

1

/4" (7mm) recommended

3

/4" x 1 1/2" x 1" (95mm x 38mm x 25mm)

3

5

/8" (905mm) to 495/8" (1260mm)

13

/16" (97 mm)

1

/16" (78 mm)

5

/8" (16mm) throw

Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 (905 mm) to 49 doors over 8'4" (2533mm). Includes screw pack for 1

5

/8" (1260 mm). Extension rod kits available for

3

/4" (44mm) to 2 1/4" (57mm) thick

metal doors. Optional 425 SNB available.

LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect LBR Less bottom rod PN Pneumatic latch retraction GBK Glass bead kit SNB Sex bolts SEC Security screws SLM Special laminate material blocking

Top – 338 - Unﬁnished, Bottom – 385A - Unﬁnished

5

/8"

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

RG

Rod guard

• Protection from carts/gurneys

• Eases wheelchair access

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

26 • Von Duprin 98/99 Series

Standard trim

EO

DT NL NL-OP TL TL-BE

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9847TL-BE-F 9947TL-BE-F

No outside trim

Exit only

Product description 9847EO-F

9947EO-F

Dummy trim

Pull when dogged (not recommended for ﬁre device)

— —

Night latch

Key retracts latchbolt

9847NL-F 9947NL-F

Night latch

Key retracts latchbolt optional pull required

9847NL-OP-F 9947NL-OP-F

Thumbturn Key locks & unlocks (use with DT trim)

9847TL-F 9947TL-F

Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm)

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

3

2

—

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

ANSI function 01 02 03 03 11 or 12 16

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

#425 SNB optional

- HMD req. WD

6 2 2 6 2 2

w/o SLM pkg.

L L-NL L-BE L-DT

9847-F/9947-F Concealed vertical rod ﬁre exit device

Lever

Key locks & unlocks

Product description 9847L-F

9947L-F

Lever – night latch

Key retracts latchbolt

9847L-NL-F 9947L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9847L-BE-F 9947L-BE-F

Lever dummy trim

pull when dogged

— —

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

#425 SNB optional

- HMD req. WD

2 2 2 2

w/o SLM pkg.

* Electriﬁed lever operation available

Notes

Von Duprin 98/99 Series • 27

9848/9948 Concealed vertical rod device

9848/9948 Concealed vertical rod device for use on single or double metal doors, UL listed for panic exit hardware. Covers stock hollow metal doors with 86 or 161 cutouts. Devices are ANSI A156.3 – 2001 Grade 1. The 9848 device has a smooth mechanism case and the 9948 device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used:SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

338

Top Strike

385A

Bottom Strike

Top Latch

Speciﬁcations

Device functions

Device lengths

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection

Latch bolt

Door undercut

Top & bottom Latch case

Vertical rods

Fasteners & sex bolts (SNB)

9848/9948 Concealed vertical rod device

28 • Von Duprin 98/99 Series

Electric options

Mechanical options

Dogging feature Dogging option

Strikes

Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm) Standard

Adjustable from 35

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar neutral – 3 Pushbar depressed – 3

Deadlocking top bolt, Deadlocking bottom bolt, 1

3

/4" (19mm) maximum, more than 1/4" minimum

1

/4" x 1 1/2" x 1 1/8" (107mm x 38mm x 28mm)

4

Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 (905 mm) to 49 doors over 8'4" (2533mm). Includes screw pack for 1

5

/8" (905mm) to 495/8" (1260mm)

13

/16" (97 mm)

1

/16" (78 mm)

3

/4" (19mm) throw

1

/2" (38mm) throw

5

/8" (1260 mm). Extension rod kits available for

3

/4" (44mm) to 2 1/4" (57mm) thick

/8"

metal doors. Optional 425 SNB available.

LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction SNB Sex bolts SEC Security screws

Hex key dogging standard

CD Cylinder dogging SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top – 338 - Unﬁnished, Bottom – 385A - Unﬁnished

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

Bottom Latch

Hex key dogging comes

standard on 9848/9948 Concealed vertical rod devices

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

SS

Signal switch

• Signals unauthorized use of an opening

• Switch makes latch bolt tamper-resistant

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

SG

Safety glow

• Shows exit door location in darkness or smoke

• Developed to meet MEA standards

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

Standard trim

EO

No outside trim

Exit only

Product description 9848EO

9948EO

DT NL NL-OP TL TL-BE

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9848TL-BE 9948TL-BE

Dummy trim

Pull when dogged

9848DT 9948DT

Night latch

Key retracts latchbolt

9848NL 9948NL

Night latch

Key retracts latchbolt optional pull required

9848NL-OP 9948NL-OP

Thumbturn Key locks & unlocks (use with DT trim)

9848TL 9948TL

Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 3

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

3

2

—

/4" x 10 3/4" x 27/32"

(70x273x21mm)

1

/4" (83mm) 3 1/4" (83mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

ANSI function 01 02 03 03 11 —

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 6 2 2

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

9848/9948 Concealed vertical rod device

L L-NL L-BE L-DT

Lever

Key locks & unlocks

Product description 9848L

9948LF

Lever – night latch

Key retracts latchbolt

9848L-NL 9948L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9848L-BE 9948L-BE

Lever dummy trim

pull when dogged

9848L-DT 9948L-DT

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 29

9848-F/9948-F Concealed vertical rod ﬁre exit device

9848-F/9948-F Concealed vertical rod device for use on pairs of doors up to 8' x 10' (2438mm x 3048mm), UL listed for ﬁre exit hardware. See page 68 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9848-F device has a smooth mechanism case and the 9948-F device has a grooved case. The concealed vertical rod device is non-handed except when the following device option is used: SS (signal switch). See opposite page for available outside trim and functions.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

338

Top Strike

385A

Bottom Strike

Top Latch

Bottom Latch

9848-F/9948-F Concealed vertical rod ﬁre exit device

Speciﬁcations

Device functions

Device lengths

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection

Latch bolt

Door undercut

Top & bottom Latch case

Vertical rods

Fasteners & sex bolts (SNB)

Electric options

Mechanical options

Dogging option No mechanical dogging. EL and QEL option available Strikes

Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm) Standard

Adjustable from 35

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar neutral – 3 Pushbar depressed – 3

Deadlocking top bolt, Deadlocking bottom bolt, 1

3

/4" (19mm) maximum, more than 1/4" minimum

1

/4" x 1 1/2" x 1 1/8" (107mm x 38mm x 28mm)

4

5

/8" (905mm) to 495/8" (1260mm)

13

/16" (97 mm)

1

/16" (78 mm)

3

/4" (19mm) throw

1

/2" (38mm) throw

Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 (905 mm) to 49 doors over 8'4" (2533mm). Includes screw pack for 1

5

/8" (1260 mm). Extension rod kits available for

3

/4" (44mm) to 2 1/4" (57mm) thick

metal doors. Optional 425 SNB available.

LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction SNB Sex bolts SEC Security screws SLM Special laminate material blocking

Top – 338 - Unﬁnished, Bottom – 385A - Unﬁnished

5

/8"

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

SS

Signal switch

• Signals unauthorized use of an opening

• Switch makes latch bolt tamper-resistant

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

30 • Von Duprin 98/99 Series

Standard trim

EO

DT NL NL-OP TL TL-BE

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9848TL-BE-F 9948TL-BE-F

No outside trim

Exit only

Product description 9848EO-F

9948EO-F

Dummy trim

Pull when dogged (not recommended for ﬁre device)

— —

Night latch

Key retracts latchbolt

9848NL-F 9948NL-F

Night latch

Key retracts latchbolt optional pull required

9848NL-OP-F 9948NL-OP-F

Thumbturn Key locks & unlocks (use with DT trim)

9848TL-F 9948TL-F

Trim description — 990DT 990NL-R/V 110NL-MD 374T X 990DT 374T-BE X 990DT

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 3

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

3

2

—

/4" x 10 3/4" x 27/32"

(70x273x21mm)

1

/4" (83mm) 3 1/4" (83mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

ANSI function 01 02 03 03 11 —

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

#425 SNB optional

- HMD req. WD

6 2 2 6 2 2

w/o SLM pkg.

L L-NL L-BE L-DT

9848-F/9948-F Concealed vertical rod ﬁre exit device

Lever

Key locks & unlocks

Product description 9848L-F

9948L-F

Lever – night latch

Key retracts latchbolt

9848L-NL-F 9948L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9848L-BE-F 9948L-BE-F

Lever dummy trim

pull when dogged (not recommended for ﬁre device)

— —

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

#425 SNB optional

- HMD req. WD

2 2 2 2

w/o SLM pkg.

* Electriﬁed lever operation available

Notes

Von Duprin 98/99 Series • 31

9849/9949 Concealed vertical cable device

338 Top strike

retroﬁt bracket

Top latch

9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for

panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9849 device has a smooth mechanism case and the 9949 device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and device functions.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 2' 2" (610 mm) Door size (shipped less UL label)

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection Pushbar neutral – 3

Latch bolt Deadlocking top & bottom bolt,

Door undercut

Top & bottom latch case

Vertical cable

Fasteners & sex bolts (SNB)

Electric options ALK Alarm exit kit

9849/9949 Concealed vertical cable device

Mechanical options

Dogging feature Hex key dogging standard Dogging option CD Cylinder dogging

Strikes Top - 249 – Unﬁnished, Bottom – 349 - Unﬁnished

*For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition.

32 • Von Duprin 98/99 Series

NL drive screw from device.

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm)

3

8" x 2

/4" x2 3/8" (203mm x 70mm x 60mm)

1

2

/4" x 2 1/4" (57mm x 57mm)

13

/16" (97 mm)

Pushbar depressed – 3

3

/4" (19mm) maximum

(24231516 spacer block kit needed for

13

/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)

5

7

/32" (6mm) Diameter stainless steel cables

Includes screw pack for 1

1

/16" (78 mm)

1

/2" (13mm) throw

3

/4" undercut)

3

/4" (44mm) to 2 1/4" (57mm) thick

metal doors. Optional 425 SNB available.

CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction

*

LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch AX Accessible device (LBL only) PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts

SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

AX

Accessible device

• UL certiﬁed to meet new 5 lb. maximum operating force requirement

• Exceeds ANSI/ BHMA requirements

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

CD

Cylinder dogging

• Replaces hex key dogging

• Requires standard 1 mortise cylinder

1

/4"

249 Top strike

349 Bottom strike

Hex key dogging comes

standard on 9849/9949 concealed vertical cable devices

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

DI

Dogging indicator

• Monitor dogging status without a control panel

• Red indicator light shows visibility to dogging from over 75 feet

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

Center slide

Bottom latch

Standard trim

EO

DT NL NL-OP

No outside trim

Exit only

Product description 9849EO

9949EO

Dummy trim

Pull when dogged

9849DT 9949DT

Night latch

Key retracts latchbolt

9849NL 9949NL

Night latch

Key retracts latchbolt optional pull required

9849NL-OP 9949NL-OP

Trim description — 990DT 990NL-R/V 110NL-MD

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

—

ANSI function 01 02 03 03

Cylinder type

Handing

Optional trim x990EO

Optional #425 SNB quantity for device

— — Rim Rim

— — — —

x996K-NL x996L-NL x696NL x697NL

x996EO

x996K-DT x996L-DT x696DT x697DT

6 2 2 6

L L-NL L-BE L-DT

9849/9949 Concealed vertical cable device

Lever

Key locks & unlocks

Product description 9849L

9949L

Lever – night latch

Key retracts latchbolt

9849L-NL 9949L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9849L-BE 9949L-BE

Lever dummy trim

pull when dogged

9849L-DT 9949L-DT

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Standard door opening height

Feet Inches

6'8" 80" 7' 8'

84" 96"

Door opening height

is measured from ﬁnished ﬂoor to frame rabbet on door side.

9' 108" 10'

Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.

120"

See table on le for standard offering.

Von Duprin 98/99 Series • 33

9849-F/9949-F Concealed vertical cable ﬁre exit device

338 Top strike

retroﬁt bracket

Top latch

9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for

panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9849 device has a smooth mechanism case and the 9949 device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and device functions.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 & 643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions

Device lengths

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection

Latch bolt

Door undercut

Top & bottom Latch case

Vertical cable

Fasteners & sex bolts (SNB)

Electric options

9848-F/9948-F Concealed vertical rod ﬁre exit device

Mechanical options

Dogging option No mechanical dogging. EL and QEL option available Strikes

34 • Von Duprin 98/99 Series

Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm) Standard

3

8" x 2

/4" x2 3/8" (203mm x 70mm x 60mm)

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar neutral – 3 Pushbar depressed – 3

Deadlocking anti-friction top & bottom bolt,

3

/4" (19mm) maximum

(24231516 spacer block kit needed for

13

/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)

5

7

/32" (6mm) Diameter stainless steel cables

Includes screw pack for 1

13

/16" (97 mm)

1

/16" (78 mm)

5

/8" (16mm) throw

3

/4" undercut)

3

/4" (44mm) to 2 1/4" (57mm) thick

metal doors. Optional 425 SNB available.

ALK Alarm exit kit CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction

*

LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch AX Accessible device (LBL only) PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts

Top – 249 - Unﬁnished, Bottom – 349 - Unﬁnished

Center slide

249 Top strike

349 Bottom strike

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull

SS

RX

E (E996L)

Bottom latch

Signal switch

• Signals unauthorized use of an opening

• Switch makes latch bolt tamper-resistant

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

operation

AX

Accessible device

• UL certiﬁed to meet new 5 lb. maximum operating force requirement

• Exceeds ANSI/ BHMA

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

requirements

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

*For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition.

Standard trim

EO

DT NL NL-OP

No outside trim

Exit only

Product description 9849EO-F

9949EO-F

Dummy trim

Pull when dogged (not recommended for ﬁre device)

— —

Night latch

Key retracts latchbolt

9849NL-F 9949NL-F

Night latch

Key retracts latchbolt optional pull required

9849NL-OP-F 9949NL-OP-F

Trim description — 990DT 990NL-R/V 110NL-MD

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

—

ANSI function 01 02 03 03

Cylinder type

Handing

Optional trim x990EO

Optional #425 SNB quantity for device

— — Rim Rim

— — — —

x996K-NL x996L-NL x696NL x697NL

x996EO

x996K-DT x996L-DT x696DT x697DT

6 2 2 6

L L-NL L-BE L-DT

9848-F/9948-F Concealed vertical rod ﬁre exit device

Lever

Key locks & unlocks

Product description 9849L-F

9949L-F

Lever – night latch

Key retracts latchbolt

9849L-NL-F 9949L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9849L-BE-F 9949L-BE-F

Lever dummy trim

pull when dogged (not recommended for ﬁre device)

— —

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Standard door opening height

Feet Inches

6'8" 80" 7' 8'

84" 96"

Door opening height

is measured from ﬁnished ﬂoor to frame rabbet on door side.

9' 108" 10'

120"

See table on le for standard offering.

Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.

Von Duprin 98/99 Series • 35

9847WDC/9947WDC Wood door concealed vertical rod device

9847WDC/9947WDC Concealed vertical rod device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847WDC device has a smooth mechanism case and the 9947WDC device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and functions.

Scalp plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to rods.

Note: Do not use on pair of doors with 9875/9975.

Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions

Device lengths

Device centerline from ﬁnished ﬂoor

Center case dimensions

Mechanism case dimensions

Projection

Latch bolt

Door undercut

Top & bottom Latch case

Vertical rods

Fasteners & sex bolts (SNB)

Electric options

9847WDC/9947WDC Wood door concealed vertical rod device

Mechanical options

Dogging feature Dogging option

Strikes

36 • Von Duprin 98/99 Series

Device ships EO/DT/NL. Field selectable. For TP, K or L remove NL drive screw from device. 2' 2" (610 mm) Door size (shipped less UL label) 3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm) Standard

Adjustable from 35

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

2

/4" x 2 1/4" (57mm x 57mm)

Pushbar neutral – 3 Pushbar depressed – 3

Deadlocking top bolt,

1

/4" (7mm) maximum

3

/4" x 1 1/2" x 1" (95mm x 38mm x 25mm)

3

Round 2-piece adjustable rods – Top rod adjustable from 6'8" (2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 (905 mm) to 49 doors over 8'4" (2533mm). Includes screw pack for 1

5

/8" (905mm) to 495/8" (1260mm)

13

/16" (97 mm)

1

/16" (78 mm)

5

/8" (16mm) throw

5

/8" (1260 mm). Extension rod kits available for

3

/4" (44mm) to 2 1/4" (57mm) thick

/8"

wood doors. 425 SNB required on wood doors without SLM blocking.

LX Latchbolt monitor switch RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit PN Pneumatic latch retraction PL Pullman latch LBR Less bottom rod SNB Sex bolts SEC Security screws

Hex key dogging standard

CD Cylinder dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator Top – 338 - Unﬁnished, Bottom – 385A - Unﬁnished

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

338

Top Strike

385A

Bottom Strike

283 Top Strike

for use with wood frames

Hex key dogging comes standard on 9847/9947 Wood door concealed vertical rod devices

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

PL

Pullman latch

• Not for use with Fire Exit Hardware

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

Top Latch

Bottom Latch

Standard trim

EO

No outside trim

Exit only

Product description 9847WDC-EO

9947WDC-EO

Trim description

Escutcheon plate size

— 990DT 990NL-R/V 110NL-WD

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm)

DT NL NL-OP TL TL-BE

Dummy trim

Pull when dogged

9847WDC-DT 9947WDC-DT

Night latch

Key retracts latchbolt

9847WDC-NL 9947WDC-NL

Night latch

Key retracts latchbolt optional pull required

9847WDCNL-OP 9947WDCNL-OP

Thumbturn Key locks & unlocks (use with DT trim)

9847WDC-TL 9947WDC-TL

376TWDC x 990DT

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

3

2

—

/4" x 10 3/4" x 27/32"

(70x273x21mm)

ANSI function 01 02 03 03 11 or 12 16

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

Optional #425 SNB quantity for device

6 2 2 6 2 2

x996K-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x696NL x697NL

1

/4" Mortise —

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9847WDC-TL-BE 9947WDC-TL-BE

376TWDC-BE x 990DT

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

9847WDC/9947WDC Wood door concealed vertical rod device

L L-NL L-BE L-DT

Lever

Key locks & unlocks

Product description 9847WDC-L

9947WDC-L

Lever – night latch

Key retracts latchbolt

9847WDC-L-NL 9947WDC-L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9847WDC-L-BE 9947WDC-L-BE

Lever dummy trim

pull when dogged

9847WDC-L-DT 9947WDC-L-DT

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Notes

Von Duprin 98/99 Series • 37

9847WDC-F/9947WDC-F Wood door concealed vertical rod ﬁre device

Top Latch

338

Top Strike

9847WDC-F/9947WDC-F Fire exit concealed vertical rod device for use on pairs of doors up to 8' x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for ﬁre exit hardware. See page 68 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9847WDC-F device has a smooth mechanism case and the 9947WDC-F device has a grooved case. The concealed vertical rod device is non-handed except when the following device options are used: SS (signal switch). See Opposite page for available outside trim and functions.

Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to rods. Note: Do not use on pair of doors with 9875-F/9975-F.

Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

NL drive screw from device.

Device lengths 2' 2" (610 mm) Door size (shipped less UL label)

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

Device centerline

5

39

/8" (1006 mm) Standard

from ﬁnished ﬂoor Center case

3

8" x 2

/4" x2 3/8" (203mm x 70mm x 60mm)

dimensions Mechanism case

1

2

/4" x 2 1/4" (57mm x 57mm)

dimensions Projection Pushbar neutral – 3

Pushbar depressed – 3

Latch bolt Deadlocking top & bottom bolt,

1

Door undercut

Top & bottom

/4" (7mm) maximum

3

/4" x 1 1/2" x 1" (95mm x 38mm x 25mm)

3

13

/16" (97 mm)

1

/16" (78 mm)

5

/8" (16mm) throw

Latch case Vertical rods Round 2-piece adjustable rods – Top rod adjustable from 6'8"

(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 (905 mm) to 49

5

/8" (1260 mm). Extension rod kits available for

5

/8"

doors over 8'4" (2533mm).

Fasteners & sex bolts (SNB)

Includes screw pack for 1 wood doors. 425 SNB required on wood doors without SLM

3

/4" (44mm) to 2 1/4" (57mm) thick

blocking.

Electric options LX Latchbolt monitor switch

RX Pushpad monitor switch RX2 Double pushpad monitor switch E Electric unlocking and locking trim EL Electric latch retraction QEL Quiet electric latch retraction SS Signal switch CX Chexit delayed exit ALK Alarm exit kit WP-RX Waterproof request to exit CON Allegion Connect

Mechanical options

GBK Glass bead kit PN Pneumatic latch retraction PL Pullman latch LBR Less bottom rod SNB Sex bolts SEC Security screws

Dogging option No mechanical dogging. EL and QEL option available Strikes Top – 338 - Unﬁnished, Bottom – 385A - Unﬁnished

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

385A

Bottom Strike

283 Top Strike

for use with wood frames

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

Bottom Latch

38 • Von Duprin 98/99 Series

Standard trim

EO

No outside trim

Exit only

Product description

Trim description

Escutcheon plate size

9847WDC-EO-F 9947WDC-EO-F

— 990DT 990NL-R/V 110NL-WD

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) — 2" (51mm) 2" (51mm)

DT NL NL-OP TL TL-BE

Dummy trim

Pull when dogged

9847WDC-DT-F 9947WDC-DT-F

Night latch

Key retracts latchbolt

9847WDC-NL-F 9947WDC-NL-F

Night latch

Key retracts latchbolt optional pull required

9847WDCNL-OP-F 9947WDCNL-OP-F

Thumbturn Key locks & unlocks (use with DT trim)

9847WDC-TL-F 9947WDC-TL-F

376TWDC x 990DT

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) — — —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

3

2

—

/4" x 10 3/4" x 27/32"

(70x273x21mm)

ANSI function 01 02 03 03 11 —

Cylinder type

Handing

— — Rim Rim 1

— — — — — —

Optional trim x990EO

x996EO

x996K-DT x996L-DT x996L-DT x696DT x697DT

x996K-NL x996L-NL x996L-NL x696NL x697NL

1

/4" Mortise —

#425 SNB optional

- HMD req. WD

6 2 2 6 2 2

w/o SLM pkg.

Thumbturn

Blank escutcheon always operable (no cylinder) (use with DT trim)

9847WDC-TL-BE-F 9947WDC-TL-BE-F

376TWDC-BE x 990DT

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

9847WDC-F/9947WDC-F Wood door concealed vertical rod ﬁre device

L L-NL L-BE L-DT

Lever

Key locks & unlocks

Product description 9847WDC-L-F

9947WDC-L-F

Lever – night latch

Key retracts latchbolt

9847WDC-L-NL-F 9947WDC-L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9847WDC-L-BE-F 9947WDC-L-BE-F

Lever dummy trim

pull when dogged

9847WDC-L-DT-F 9947WDC-L-DT-F

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

#425 SNB optional

- HMD req. WD

2 2 2 2

w/o SLM pkg.

* Electriﬁed lever operation available

Notes

Von Duprin 98/99 Series • 39

9849WDC/9949WDC Wood door concealed vertical cable device

9849WDC/9949WDC Concealed vertical cable device for use on single or double wood doors, UL listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847WDC device has a smooth mechanism case and the 9947WDC device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SD (special dogging), or SS (signal switch). See Opposite page for available outside trim and functions.

Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to cables.

Note: Do not use on pair of doors with 9975 devices.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &

643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 2' 2" (610 mm) Door size (shipped less UL label)

Device centerline from ﬁnished ﬂoor Center case dimensions Mechanism case dimensions Projection Pushbar neutral – 3

Latch bolt Deadlocking top & bottom bolt. 1

Door undercut

Top & bottom Latch case Vertical cables

Fasteners & sex bolts (SNB)

Electric options ALK Alarm exit kit

9849WDC/9949WDC Wood door concealed vertical cable device

Mechanical options

Dogging feature Hex key dogging standard Dogging option CD Cylinder dogging

40 • Von Duprin 98/99 Series

Strikes Top - 249 – Unﬁnished, Bottom – 349 - Unﬁnished

NL drive screw from device.

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm) Standard

3

/4" x2 3/8" (203mm x 70mm x 60mm)

8" x 2

1

/4" x 2 1/4" (57mm x 57mm)

2

13

/16" (97 mm)

Pushbar depressed – 3

3

/4" (19mm) maximum

(24231516 spacer block kit needed for

13

/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)

5

7

/32" (6mm) Diameter stainless steel cables

Includes screw pack for 1

1

/16" (78 mm)

1

/2" (38mm) throw

3

/4" undercut)

3

/4" (44mm) to 2 1/4" (57mm) thick wood doors. 425 SNB required on wood doors without SLM blocking.

CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction

*

LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts

SD Special center case dogging LD Less dogging DI Dogging indicator CI Cylinder dogging indicator

338 Top strike

retroﬁt bracket

249 Top strike

349 Bottom strike

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull operation

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

Top latch

Center slide

Bottom latch

Hex key dogging comes

standard on 9849/9949 Wood door concealed vertical cable devices

ALK

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

RX

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

LX

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

*For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition.

Standard trim

EO

DT NL NL-OP

No outside trim

Exit only

Product description 9849WDC-EO

9949WDC-EO

Dummy trim

Pull when dogged

9849WDC-DT 9949WDC-DT

Night latch

Key retracts latchbolt

9849WDC-NL 9949WDC-NL

Night latch

Key retracts latchbolt optional pull required

9849WDC-NL-OP 9949WDC-NL-OP

Trim description — 990DT 990NL-R/V 110NL-WD

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

—

ANSI function 01 02 03 03

Cylinder type

Handing

Optional trim x990EO

Optional #425 SNB quantity for device

— — Rim Rim

— — — —

x996K-NL x996L-NL x696NL x697NL

x996EO

x996K-DT x996L-DT x696DT x697DT

6 2 2 6

L L-NL L-BE L-DT

9849WDC/9949WDC Wood door concealed vertical cable device

Lever

Key locks & unlocks

Product description 9849WDC-L

9949WDC-L

Lever – night latch

Key retracts latchbolt

9849WDC-L-NL 9949WDC-L-NL

Lever – blank escutcheon

Always operable (no cylinder)

9849WDC-L-BE 9949WDC-L-BE

Lever dummy trim

pull when dogged

9849WDC-L-DT 9949WDC-L-DT

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Standard door opening height

Feet Inches

6'8" 80" 7' 8'

84" 96"

Door opening height

is measured from ﬁnished ﬂoor to frame rabbet on door side.

9' 108" 10'

Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.

120"

See table on le for standard offering.

Von Duprin 98/99 Series • 41

9849WDC-F/9949WDC-F Wood door concealed vertical cable ﬁre device

Top latch

338 Top strike

retroﬁt bracket

9849WDC-F/9949WDC-F Fire exit concealed vertical cable device for use on pairs of doors up to 8' x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for ﬁre exit hardware. See page 61 for detailed information on UL listed ﬁre exit hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The 9849WDC-F device has a smooth mechanism case and the 9949WDC-F device has a grooved case. The concealed vertical cable device is non-handed except when the following device options are used: SS (signal switch). See opposite page for available outside trim and functions.

Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to cables.

Note: Do not use on pair of doors with 9975 devices.

Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &

643E. US15 and US32D available with 98 Series only.

Speciﬁcations

Device functions Device ships EO/DT/NL. Field selectable. For TP, K or L remove

Device lengths 2' 2" (610 mm) Door size (shipped less UL label)

Device centerline from ﬁnished ﬂoor Center case dimensions Mechanism case dimensions Projection Pushbar neutral – 3

Latch bolt Deadlocking top & bottom bolt, 1

Door undercut

Top & bottom Latch case Vertical cables

Fasteners & sex bolts (SNB)

Electric options ALK Alarm exit kit

9847WDC-F/9947WDC-F Wood door concealed vertical rod ﬁre device

Mechanical options

Dogging option No mechanical dogging. EL and QEL option available Strikes Top – 249 - Unﬁnished, Bottom – 349 - Unﬁnished

42 • Von Duprin 98/99 Series

NL drive screw from device.

3' 2'4' to 3' (711mm to 914 mm) Door size 4' 2'10" to 4' (864 mm to 1219 mm) Door size

5

39

/8" (1006 mm) Standard

3

8" x 2

/4" x2 3/8" (203mm x 70mm x 60mm)

1

2

/4" x 2 1/4" (57mm x 57mm)

13

/16" (97 mm)

Pushbar depressed – 3

3

/4" (19mm) maximum

(24231516 spacer block kit needed for

13

/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)

5

7

/32" (6mm) Diameter stainless steel cables

Includes screw pack for 1

1

/16" (78 mm)

1

/2" (38mm) throw

3

/4" undercut)

3

/4" (44mm) to 2 1/4" (57mm) thick wood doors. 425 SNB required on wood doors without SLM blocking.

CX Chexit delayed exit E Electric unlocking and locking trim EL Electric latch retraction HD-EL Electric latch retraction w/ hex dogging QEL Quiet electric latch retraction

*

LX Latchbolt monitor switch RX2 Double pushpad monitor switch RX996L Trim monitor switch RX Pushpad monitor switch RXLC Pushpad monitor switch - low current SS Signal switch WP-RX Waterproof request to exit CON Allegion Connect GBK Glass bead kit LBL Less bottom latch PN Pneumatic latch retraction SEC Security screws SG Safety glow SNB Sex bolts SLM Special laminate material blocking

Center slide

249 Top strike

349 Bottom strike

CX

Chexit delayed exit

• Meets NFPA 101 requirements

• Self-contained controls, locking, alarm

EL

Electric latch retraction

• Enables remote unlatching

• Alternative to manual dogging

QEL

Quiet electric latch retraction

• Bolt retraction via switch

• Converts exit door to push-pull

ALK

LX

RX

Bottom latch

Alarm exit kit

• Unauthorized opening triggers 85-decibel horn

• Set in armed or disarmed mode by key

Latchbolt monitor switch

• Signals use of an opening

• SPDT switch to monitor latch bolt

Pushpad monitor switch

• Signals use of an opening

• SPDT switch to monitor pushpad

operation

E (E996L)

Electriﬁed breakaway lever

• Electriﬁed remote locking/unlocking

• Standard in fail safe condition

CON

Allegion Connectors

• Common connectors to connect various door hardware all the way to the power supply

PN

Pneumatic latch retraction

• For areas where electrical devices banned

• Special linkage for mechanical or pneumatic dogging

*For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor latchbolt condition.

Standard trim

EO

DT NL NL-OP

No outside trim

Exit only

Product description 9849WDC-EO-F

9949WDC-EO-F

Dummy trim

Pull when dogged (not recommended for ﬁre device)

— —

Night latch

Key retracts latchbolt

9849WDC-NL-F 9949WDC-NL-F

Night latch

Key retracts latchbolt optional pull required

9849WDC-NL-OP-F 9949WDC-NL-OP-F

Trim description — 990DT 990NL-R/V 110NL-WD

Escutcheon plate size

—

Pull center to center — 5

Projection

— 2" (51mm) 2" (51mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

1

/2" (140mm) 5 1/2" (140mm) —

13

3" x 14

/16" x 3/32"

(76x360x2mm)

—

ANSI function 01 02 03 03

Cylinder type

Handing

Optional trim x990EO

Optional #425 SNB quantity for device

— — Rim Rim

— — — —

x996K-NL x996L-NL x996L-NL x696NL x697NL

x996EO

x996K-DT x996L-DT x996L-DT x696DT x697DT

6 2 2 6

L L-NL L-BE L-DT

Lever

Key locks & unlocks

Product description 9849WDC-L-F

9949WDC-L-F

Lever – night latch

Key retracts latchbolt

9849WDC-L-NL-F 9949WDC-L-NL-F

Lever – blank escutcheon

Always operable (no cylinder)

9849WDC-L-BE-F 9949WDC-L-BE-F

Lever dummy trim

pull when dogged (not recommended for ﬁre device)

— —

Trim description 996L-R/V* 996L-NL-R/V 996L-BE-R/V* 996L-DT

Escutcheon plate size

3

2

/4" x 10 3/4" x 27/32"

(70x273x21mm)

2 3/4" x 10 3/4" x 27/32" (70x273x21mm)

Pull center to center — — — —

Projection

7

2

/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm) 2 7/8" (73mm)

ANSI function 08 03 14 02

Cylinder type

Handing

Optional #425 SNB quantity for device

* Electriﬁed lever operation available

Rim Rim — —

Handed/Reversible Handed/Reversible Handed/Reversible Handed/Reversible

2 2 2 2

Standard door opening height

Feet Inches

6'8" 80" 7' 8'

84" 96"

Door opening height

is measured from ﬁnished ﬂoor to frame rabbet on door side.

9' 108" 10'

Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.

120"

See table on le for standard offering.

Von Duprin 98/99 Series • 43

98/99 Optional trim

Knob, exit only and thumbpiece trim – 990 & 996K

K-NL K-BE K-DT EO TP TP-BE EO

Thumbpiece blank escutcheon

Always operable (no cylinder) Exit only plate

3" x 143/16" x 3/32" (76x360x2mm)

Knob – night latch

Key retracts latchbolt

23/4" x 103/4" x 27/32" (70x273x21mm)

Knob – blank escutcheon

Always operable (no cylinder)

23/4" x 103/4" x 27/32" (70x273x21mm)

Knob – dummy trim

Pull when dogged Exit only plate

23/4" x 103/4" x 27/32" (70x273x21mm)

3" x 143/16" x 3/32" (76x360x2mm)

Thumbpiece

Key locks & unlocks

3" x 143/16" x 3/32" (76x360x2mm)

1

/2" (140mm) 51/2" (140mm) 51/2" (140mm)

3" x 143/16" x 3/32" (76x360x2mm)

Trim description

Escutcheon plate size

Pull center to center

Projection

ANSI function

K

Knob

Key locks & unlocks

996K 996K-NL 996K-BE 996K-DT 996EO 990TP 990TP-BE 990EO

3

/4" x 103/4" x 27/32"

2 (70x273x21mm)

— — — — — 5

1

3

/4" (83mm) 31/4" (83mm) 31/4" (83mm) 31/4" (83mm) — 2" (51mm) 2" (51mm) Z

08 09 14 02 01 05 14 14

Cylinder type

Rim or vertical rod

Rim Rim — — — Rim — —

device

Mortise lock device

Handing

1

/4" Mortise 11/4" Mortise — 11/4" Mortise — —

1

— — — — — — — —

#425 SNB optionalHMD req.

Trim options

WD w/o SLM pkg.

2 2 2 2 2 2 2 2

#825 SNB req. WD w/o SLM pkg F

2 2 2 2 2 2 2 2

Rim device ONLY

#425 SNB req. w/499F

2 2 2 2 2 2 2 2

44 • Von Duprin 98/99 Series

98/99 Optional trim

Optional trims – 696

DT

Dummy trim

Pull when dogged (not recomended for ﬁre device)

NL

Night latch

Key retracts latchbolt

TP

Thumbpiece

Key locks & unlocks

TP-BE

Thumbpiece – blank escutcheon

Always operable (no cylinder)

Trim description 696DT 696NL 696TP 696TP-BE

Escutcheon plate size

Pull center to center 5

Projection

3

/4" x 103/4" x 27/32"

2 (70x273x21mm)

1

/2" (140mm) 51/2" (140mm) 51/2" (140mm) 51/2" (140mm)

1

2

/6" (52mm) 2 1/6" (52mm) 2 1/6" (52mm) 2 1/6" (52mm)

23/4" x 103/4" x 27/32" (70x273x21mm)

15/8" x 131/2" x 3/16" (41x343x5mm)

ANSI function 02 03 05 15

Cylinder type

Rim or vertical rod device

Mortise lock device

Handing

#425 SNB optional-HMD req. WD w/o SLM pkg.

#825 SNB req. WD w/o SLM pkg F Rim device ONLY

— Rim Rim —

1

— 1

/4" Mortise 11/4" Mortise —

— — — —

2 2 2 2

#425 SNB req. w/499F 2 2 2 2

Trim options

Optional trims – 697

DT

Dummy trim

Pull when dogged (not recomended for ﬁre device)

Trim description 697DT 697NL 697TP 697TP-BE

Escutcheon plate size

Pull center to center 5

Projection

ANSI function 02 03 05 15

Cylinder type

Rim or vertical rod device

Mortise lock device

Handing

#425 SNB optional-HMD req. WD w/o SLM pkg.

#825 SNB req. WD w/o SLM pkg F Rim device ONLY

#425 SNB req. w/499F 2 2 2 2

3

/4" x 103/4" x 27/32"

2 (70x273x21mm)

1

/2" (140mm) 51/2" (140mm) 51/2" (140mm) 51/2" (140mm)

3" (76mm) 3" (76mm) 3" (76mm) 3" (76mm)

— Rim Rim —

— 1

— — — —

2 2 2 2

NL

Night latch

Key retracts latchbolt

23/4" x 103/4" x 27/32" (70x273x21mm)

1

/4" Mortise 11/4" Mortise —

TP

Thumbpiece

Key locks & unlocks

15/8" x 131/2" x 3/16" (41x343x5mm)

(3/4" diameter pull) (19mm)

TP-BE

Thumbpiece – blank escutcheon

Always operable (no cylinder)

23/4" x 103/4" x 27/32" (70x273x21mm)

(3/4" diameter pull) (19mm)

Von Duprin 98/99 Series • 45

98/99 Optional trim

E996L Electriﬁed breakaway lever

E996L Electriﬁed lever trim provides remote locking and unlocking. Furnished standard in fail safe (FS) condition, can be ﬁeld converted to fail secure (FSE) where allowed. E996L is furnished standard with cylinder operation for nightlatch (NL) function, or with blank escutcheon (BE).

Speciﬁcation:

solenoid – continuous duty 24VDC

Solenoid draw –

0.22 amp.

To order, specify:

1. Use “E” preﬁx, example E996L. When ordering with the exit device specify trim series with preﬁx “E”, example 9927L-BE 3' US26D E996.

2. Device type, R/V (rim/surface vertical rod/concealed

vertical rod) or M (mortise).

3. RHR furnished standard if not speciﬁed, ﬁeld reversible.

4. Lever style (06 lever furnished standard).

Other levers, no extra charge.

392-7 Offset pull

The 392-7 Offset pull is 3/4₄" round stainless steel, with a 7" center to center which matches the 98/99 center case. Oen used with a night latch operation. 3

1

/2" (89mm) offset with 1 1/2₂"

(38mm) clearance.

Vandal resistant trim: IVES VR910 & VR914 Series

VR910 grip coated in black plastisol for soer touch and resilience to temperature extremes. Grip designed for comfortable operation. VR914 grip in all stainless steel.

Features:

• Stainless steel construction, 11 gauge

(0.120" thick)

• Finish: US32D, only

• Thru-bolts and rugged mounting screws for

maximum fastening strength.

• Built-in lock protector prevents vandalism to

mortise latchbolt (available on certain models).

• Extra-tough stainless steel cylinder collar prevents pipe wrench

or similar tool from damaging cylinder. Tapered design prevents side impacts from transferring directly to cylinder. Collar spins freely.

• Furnished with mounting screws for door thicknesses

3

of 1

/4" to 2 1/4"

Trim options

Model

VR910DT & VR914DT 98/99 Rim or

HL6 Hospital pull

Von Duprin and Glynn-Johnson have collaborated on an exit device trim that answers the problem of accessibility and performance. Using the Von Duprin 98/9975 mortise lock exit device along with the Glynn-Johnson HL6 push/pull latch, Allegion has created an exit device with mortise lock durability that utilizes a fully ADA compliant Pull paddle trim.

VR910NL & VR914NL 98/99 Rim or

VR910M-DT & VR914M-DT 9875/9975

VR910M-NL & VR914M-NL Handing required

For use with Size

1

5

vertical rod device

Mortise device 9875/9975

Mortise device

/2" (133mm) w

x 11" (279mm) h

1

5

/2" (133mm) w

x 11" (279mm) h

1

7

/4" (184mm) w

x 11" (279mm) h

1

7

/4" (184mm) w

x 11" (279mm) h

The 98/9975HL device is available in all standard architectural ﬁnishes. Consult the Glynn-Johnson catalog for complete product information.

• Meets ANSI/BHMA 156.13, Trim security test and

California State Accessibility Standards Title 24.

1

• 1

/2" (38mm) clearence from grip to door,

total projection 1

7

/8" (48mm)

• Consult the IVES catalog for complete product information.

46 • Von Duprin 98/99 Series

98/99 Optional trim

This page intentionally le blank

Trim options

Von Duprin 98/99 Series • 47

Schlage AD-Series

AD-Series adaptable electronic locks

The AD-Series was designed to be the right choice for today, and is ready to adapt to whatever the future holds.

There are a variety of options that allow you to select the AD-Series electronic lock that’s right for you, and a wide selection of features that can be conﬁgured in the ﬁeld to further customize each opening. When your needs change in the future, the innovative modular design of the AD-Series allows you to easily upgrade the credential reader or networking option, and adapt to emerging technologies using your existing chassis – all without taking the lock off the door. This means that you can be conﬁdent that your choice of the AD-Series is right for today, and that your investment will be protected into the future.

Credential reader options

AD-Series electronic locks are compatible with many different brands and technologies of credentials.

• Multi-technology (reads 125 kHz prox and 1

3.56 MHz smart)

+

KEYPAD

Standalone

Standalone locks are a cost-effective solution for doors that do not require real-time monitoring. The AD-Series standalone solution provides:

• Upgradability

• Improved credential

• Audit trail reports

Schlage offers two AD-Series standalone solutions to ﬁt your environment:

AD-200 Access rights are stored on the lock AD-250 Access rights are stored on the magnetic stripe credential

management

Chassis

• Cylindrical

• Mortise

• Mortise deadbolt

• Exit trim*

Locking functions

• Classroom/Storeroom

• Oce

• Privacy

• Apartment

Lever styles

• Magnetic stripe

(insertion)

+

KEYPAD

Sparta Rhodes Athens Tubular

Warm Tone Finishes

Trim options

• Magnetic stripe

• Keyp ad

Communications options

Networked

In facilities where increased monitoring and control are needed, a networked solution is essential. The AD-Series networked options feature:

• Open architecture platform

• Acceptable reader technology

• Real-time monitoring

The AD-Series networked lock is available in either a wireless or hardwired conﬁguration to ﬁt your application needs.

AD-300 Networked hardwired locks AD-301 Networked hardwired FIPS 201-1 compliant locks AD-400 Networked wireless locks AD-401 Networked wireless FIPS 201-1 compliant locks

(swipe)

+

KEYPAD

605 606 612 643e Bright brass Satin brass Satin bronze Aged bronze

Cool Tone Finishes

619 625 626 626AM Satin nickel Bright Satin chrome Satin chrome chrome with antimicrobial

Certiﬁcations

• ANSI/BMHA A156.25 • ADA

• ANSI/BHMA Grade 1 • FCC part 15

• UL 294 Listed • RoHS

• UL 10C • FIPS 201-1 (AD-301 and AD-401)

Complete your system

Complete your AD-Series system with readers and credentials, biometric hand geometry readers, system components, HHD programming device and other wireless accessories.

* See AD-Series exit trim compatibility Datasheet for complete list of compatability by

manufacturer.

48 • Von Duprin 98/99 Series

Schlage CO-Series

CO-Series electronic locks from Schlage

In the world of standalone electronic locks, nothing compares to the CO-Series from Schlage. And because CO-Series locks offer a wide variety of options, it’s easy to ﬁnd the right solution for any facility. For openings with a relatively small number of users, we recommend the C0-100. It’s an oine keypad programmable lock. For larger applications try the CO-200 or CO-250. They’re computer programmable locks that can provide audit trails. They also offer dual credential options (card+PIN) that provide an even greater level of security.

Compatible

The CO-Series was designed to easily integrate into your facility. It can work in conjunction with Schlage and Locknetics electronic locks and offers expanded cylinder, exit device, and credential compatibility.

Exit device compatibility*

Rim SV R CV R/CVC Mortise

Von Duprin 98/99 & 98/99 XP

Von Duprin 22/22F

Falcon 25

* See AD-Series Exit trim compatibility datasheet for complete list of compatability by

manufacturer.

4 4 4 4

4 4

4

Cylinder compatibility

Full size

key-in-lever 6 pin

Schlage

Falcon

®

Sargent (10L + 11L full size)

Corbin Russwin

®

Yal e

(includes Medeco 31*0100 FSIC)

®

Best

l = with cylinder or less cylinder options

s = less cylinder only

Q = less cylinder, only with Sparta and Rhodes levers

Note: See price book for speciﬁc conﬁgurations

l l l

s Q

s s s

®

Full size

key-in-lever 7 pin

FSIC

6 & 7 pin

s s

SFIC

6 & 7 pin

s

Class

CO-100

• Manually programmable • User rights stored on the lock

• Keypad only

CO-200 (shown)

• Computer or manually programmable

• User rights stored on the lock

CO-250

• Computer programmable • User rights stored on the card

Readers

• Keypad

• Magnetic stripe (swipe)

• Proximity

• Magnetic stripe plus keypad (swipe)

• Proximity plus keypad

Lever styles

Sparta Rhodes Athens Tubular

Chassis

• Cylindrical

• Mortise

• Mortise deadbolt

• Exit Trim

Power

• 4 standard off the shelf (AA) batteries

Functions

• Classroom/storeroom

• Privacy

• Oce

Warm tone ﬁnishes

605 606 612 643e Bright brass Satin brass Satin bronze Aged bronze

Trim options

Credential compatibility

The CO-Series is compatible with many different brands and credential technologies.

For customers with an installed base of iButtons proximity keyfob with iButton option is available to make an easy transition to proximity technology.

®

, a combo

Cool tone ﬁnishes

619 625 626 626AM Satin nickel Bright Satin chrome Satin chrome chrome with antimicrobial

Reliable

When it comes to securing your facility, you can’t afford to take chances. CO-Series locks are tested to the highest quality and reliability standards in the industry, including:

• NSI/BHMA A156.25 & ANSI/BHMA Grade 1

• UL 294

• UL 10C

• ADA

Von Duprin 98/99 Series • 49

98/99 Strike/Stile information

Device type

Standard single door

Strike Trim/Stile

Standard double door

Strike w/ mullion* Trim/Stile Strike Trim/stile

Optional single door

Optional double door

Strike w/mullion* Trim/Stile

990/996 696/697 990/996 696/697 990/996 696/697 990/996 696/697

7

/16"

4 1/4" (108mm)

13

3

7

13

3

/16"

/8"

/4"

/16"

/8"

13

3

/16"

(97mm) 4 1/4"

(108mm)

4 3/4" (121mm)

4 1/4" (108mm)

13

3

/16"

(97mm) 4 1/4"

(108mm)

98/99 299

XP 98/99 909

98-F/99-F 299F

XP98-F/XP99-F 909

9875 9975

9875-F 9975-F

9857 9957

9857-F 9957-F

575

299 (Top) 299 (Middle) 304L/284-L (Bottom)

299 (Top) 299F (Middle) 304L (Bottom)

1

/2"

4 (114mm)

1

/2"

4 (114mm)

3

/4"

4 (121mm)

3

/4"

4 (121mm)

1

/2"

4 (114mm)

1

/2"

4 (114mm)

4 3/8" (111mm)

4 3/4" (121mm)

4 3/8" (111mm)

299 x 4954

909 x 4954-XP

499F x 9954

954 x 9954-XP

7

/8"

4 (124mm)

7

/8"

4 (124mm)

4 3/4" (121mm)

1439 or 1410

1606

13

3 (97mm)

1

/16"

4 (103mm)

/16"

13

3 (97mm)

15

3 (100mm)

— — — — — —

— — —

— — — — — —

/16"

299 x 5654

1408 x 5754

1606 x 1654

499F x 9854 KR9954

575-2 — — — — — 576A-576B

299 x 4954

299F 499F x 9954 304L

4 7/8" (124mm)

7

/8"

4 (124mm)

4 3/4" (121mm)

1439 or 1410

1606

13

3 (97mm)

1

/16"

4 (103mm)

/16"

13

3 (97mm)

15

3 (100mm)

— — — — — —

/16"

299 x 5654

1408 x 5754

1606 x 1654

4 (113mm)

3 (97mm)

4 (112mm)

— —

4 (121mm)

4 (113mm)

3 (97mm)

4 (112mm)

Strike Application Trim/Stile Optional strike Application Trim/Stile

990/996 696/697 990/996 696/697

9827 9927 Latch retraction

PL9827/PL9927 Pullman latch

9827-F 9927-F

9847 9947 9848 9948

9847-F 9947-F 9848-F 9948-F

Strike options / Dogging options

9847WDC 9947WDC

9847WDC-F 9947WDC-F

9849 9949 9849 9949

9849-F 9949-F 9849-F 9949-F

9849WDC 9949WDC

9849WDC-F 9949WDC-F

299 (Top) 304L/248-L-4 (Bottom)

299 (Top) 304L (Bottom)

338 (Top) 385A (Bottom)

249 (Top) 349 (Bottom)

Single door

Two vertical rod devices

Vertical rod with Mortise lock device

Two vertical rods

Vertical rod with Mortise lock device

Single door

Two vertical rod devices

Vertical rod with Mortise lock device

Two vertical rod devices

Vertical cable with Mortise lock device

Two vertical cables

Vertical cable with Mortise lock device

Single door

Two vertical cable devices

Vertical cable with Mortise lock device

Two vertical cable devices

11

3

/16"

(94mm)

11

/16"

3 (94mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

1

/4"

4 (108mm)

1

/4"

4 (108mm)

1

/4"

4 (108mm)

3 5/8" (92mm)

4 3/4" (121mm)

4 1/8" (105mm)

4 3/4" (121mm)

4 1/4" (108mm)

4 3/4" (121mm)

4 1/4" (108mm)

4 3/4" (121mm)

4 1/4" (108mm)

4 3/4" (121mm)

4 1/4" (108mm)

260U (Top) 385A (Bottom)

260U (Stainless) 385A (Bottom)

304L (Bottom)

304L

—

Single door

Two vertical rod devices

Vertical rod with Mortise lock device

Two vertical rods

Vertical rod with Mortise lock device

Single door

Two vertical rod devices

Vertical rod with Mortise lock device

Two vertical rod devices

Vertical cable with Mortise lock device

Two vertical cable

Vertical cable with Mortise lock device

Single door

Two vertical Cable devices

Vertical cable with Mortise lock device

Two Vertical Cable Devices

11

/16"

3 (94mm)

11

3

/16"

(94mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

4 1/4" (108mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

1

4

/4"

(108mm)

1

/4"

4 (108mm)

3

/4"

4 (121mm)

1

/4"

4 (108mm)

3 5/8" (92mm)

4 3/4" (121mm)

4 1/8" (105mm)

4 3/4" (121mm)

4 1/4" (108mm)

4 3/4" (121mm)

4 1/4" (108mm)

4 3/4" (121mm)

4 1/8" (105mm)

4 3/4" (121mm)

4 1/4" (108mm)

4 3/4" (121mm)

4 1/4" (108mm)

50

50 • Von Duprin 98/99 Series

98/99 Strike information

249

349

Strikes for rim devices

264 299 299F 499F

1408

Projection

9

/16" (14mm) Projection

13

/16" (21mm) Projection

13

/16" (21mm) Projection

1439–Blade stop 1410–Integral stop 1606 1609

3

/8" (10mm)

– Requires coordinator – For panic exit application only, not ﬁre rated

Strikes for vertical cable devices

249 - Top strike 349 - Bottom strike

1"

(25 mm)

1¹⁄₂"

(38 mm)

¹⁄₈"

⁹⁄₁₆"

(14 mm)

Projection

(3 mm)

9

/16" (14mm) Projection 1/8" (3mm)

Projection

1

/2" (13mm) Projection 1/2" (13mm)

XP Strikes for rim devices

909 954

Projection

13

/16" (21mm)

- For ﬁre rated double door applications

7

/8" (22mm)

Projection Panic devices only

Strikes for vertical rod devices

248L-4 260U-Flush transom panic only

260U-F-Flush transom ﬁre only

299 299F

15

/16" (24mm) One per pair of doors

1¹⁹⁄₃₂"

(40 mm)

2³⁄₄"

(70 mm)

¹⁄₈"

(3 mm)

Strike options / Dogging options

Projection

3

/8" (10mm) Projection 3/8" (10mm) Projection 13/16" (21mm) Projection 13/16" (21mm)

304L 338 385A 283

Projection

13

/16" (21mm) Mortise 5/8" (16mm) Mortise 2 1/2" (64mm)

Strikes for mortise rod devices

575 575-2 576A 576B

.

– Not for use with astragals – For use on wood doors,

contact door manufacturer

For use with WDC devices when used with wood frames

– Acceptable for 90 minute

pair of hollow metal doors

Von Duprin 98/99 Series • 51

51

98/99 Dogging options

CD Cylinder dogging

Cylinder dogging is available on all 98/99™ Panic exit devices to replace the standard hex key dogging. Unit requires a standard

3

1

/4" (32mm) mortise cylinder with an inverted straight cam

(Schlage Cam B502-191 reference).

To order, specify:

• Use preﬁx, CD, example CD99L

CDK Cylinder dogging kit

*

For ﬁeld conversion, a cylinder dogging conversion kit is available.

Order: 99CDK or 98CDK, specify ﬁnish.

*Cannot be added to ﬁre exit hardware.

HDK Hex key dogging kit

*

For ﬁeld conversion, a hex key dogging conversion kit is available.

Order: 99HDK or 98HDK, specify ﬁnish.

*Cannot be added to ﬁre exit hardware.

LD Less dogging

Less dogging is available in all 98/99™ Panic exit devices to remove the dogging option.

To order, specify:

• Use preﬁx LD, example LD99L

SD Special center case dogging

Special cylinder dogging in the center case is available for Chexit, EL, QEL, ALK panic devices to allow for mechanical push/pull operation. With this option, the latchbolt is held retracted and pushbar is still operable. Specify handing—RHR or LHR.

SD requires 1

3

/4" (32mm) mortise cylinder with an inverted

straight cam. (Schlage cam reference B502-191.)

Note: Available on Rim and Vertical Rod Panic Exit Devices only.

To Order, Specify:

• Use preﬁx SD, example SD99L and Handing

• Not for 98/9975 Devices

Double cylinder

Double cylinder features an inside key cylinder which locks or unlocks the outside trim and an outside key cylinder which retracts the latch bolt only (Night latch function). Available on rim or mortise lock device.

Dog keys

Dog key (old style) Dog key (standard)

2 3/16" (56mm)

2 3/4" (70mm)

Rim requires two rim type cylinders. Mortise device requires 1 rim cylinder and 1 mortise cylinder 1

1

/4" with a straight cam. (Schlage

cam reference B502-191.)

Available functions are thumbpiece, knob or lever.

To order, specify:

1. Sux-2 with device/trim number, example 99TP-2.

7

Strike options / Dogging options

/32" (6mm) hex

5

/32" (4mm) hex

2. Handing required, LHR or RHR.

-2SI Double cylinder with security indicator

The Von Duprin Classroom Security Indicator provides an at-aglance veriﬁcation of the locked/unlocked status of the door from inside of the room. This option can be ordered as a new product or as a retroﬁt conversion kit to an existing 98/99 device. Indicator in Unlocked state presents a background with black icon) at top of device head. Indicator in

Locked state has no ﬂag present.

To order, specify:

1. Sux-2SI with device/trim number, example 99L-2SI.

2. Handing required, LHR or RHR.

1

/2" x 1/2" metal ﬂag (white

52

52 • Von Duprin 98/99 Series

98/99 Electrical options

RX Request to exit

The RX (2xit) feature is used to signal the use of an opening. This device is equipped with one internal SPDT switch which monitors the pushpad.

The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply.

The RX switch option should not be used to control a load, but as a signalling switch (0.5 amps. resisitive maximum).

The RX switch is available in a low current (LC) switch. Most commonly used in computer operated monitoring systems.

To order, specify:

• Standard – use preﬁx RX, example RX99EO

• Low Current – use preﬁx RX-LC, example RX-LC98EO

RX2 Double request to exit

The RX2 feature uses two RX switches.

To order, specify:

• Standard – Use preﬁx RX2, example RX299EO

WP-RX Waterproof request to exit

LX Latchbolt monitoring

SS Signal switch

Monitors pushpad and latch bolt

The SS feature is used to signal the unauthorized use of an opening. This device is equipped with two internal SPDT switches. One switch monitors both the pushpad and the latch bolt assembly, making the latch bolt tamper resistant, for positive security. An additional SPDT switch is connected to the

1

/4" (32mm) mortise cylinder with straight cam for alarm “bypass.” (Schlage cam reference B502-191). The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply.

Pushpad reads: “Emergency Exit ONLY – Push To Open And Sound Alarm.” Pushpad is only available in US32D ﬁnish with red silk-screened lettering.

The SS mortise lock device is furnished with both the signal switch device and the SS7500 mortise lock. The SS7500 mortise lock has the versatility and advantages of the 7500 lock with the addition of signalling functions to monitor latch bolt operation and the trim locking function. The SS7500 mortise lock is supplied standard with the SS mortise lock device.

To order, specify:

1. Preﬁx SS, example SS99L.

2. Handing required, LHR or RHR.

Electrical ratings:

Up to 2.0 AMPS @ 24VDC

Electrical options & accessories

The LX feature is used to signal the use of an opening. This device is equipped with one internal SPDT switch which monitors the latch bolt.

The device can be connected to a security console, or may be used as a single door alarm when used with a horn and power supply.

The LX switch option should not be used to control a load, but as a signalling switch (0.5 amps. resistive maximum).

The LX switch is available in a low current (LC) switch. Most commonly used in computer operated monitoring systems.

To order, specify:

• Standard – Use preﬁx LX, example LX99EO

• Low Current – Use preﬁx LX-LC, example LX-LC98EO

Electrical rating for all switches:

• Standard – 2 Amp maximum @ 24VDC

• Low Current (LC) - below 50 Milliamps @ 24VDC

Note: All switches can be either factory or ﬁeld installed

Popular SS application

Unauthorized use of this opening will activate the local horn. The key switch permits inhibiting this system for authorized entry.

Von Duprin 98/99 Series • 53

53

98/99 Electrical options

CX The Chexit

Designed for use on delayed exit applications, the Chexit system is ideal for controlled areas.

All controls, auxiliary locking, local alarm, and remote signalling are self-contained in the Chexit, providing safe, secure, easy to install and simple to operate door control and exit hardware.

Chexit controlled exit device for use on panic or ﬁre exit hardware applications.

This concept in delayed exit systems combines life safety with the needs of security and meets all requirements of NFPA 101 for “special locking arrangement.”

The Chexit device includes a 6" x 20" decal for application on door.

“PUSH UNTIL ALARM SOUNDS. DOOR CAN BE OPENED IN 15 SECONDS”

Minimum width door opening:

• 3' Device 34" opening

• 4' Device 40" opening

Consult factory for other size requirements.

®

Power supply requirements

Solenoid speciﬁcations:

• Continuous duty – 24VDC

• Current inrush – 16 amperes

• Current holding – .3 amperes

Requires PS914 Power Supply

Internal horn: Whenever the device is in alarm or the push pad is pressed the internal horn will sound. The volume level of this horn exceeds 85 db at 6 feet.

Door position input: An external door position switch can be connected to the Chexit.

Using the door position input ensures that the door is in the closed and latched position before the device rearms.

External inhibit input: This optional input is provided to allow authorized egress of the Chexit in the armed condition. It also allows remote reset of the Chexit in an alarmed condition.

Fire alarm input: This input disables the Chexit immediately upon a ﬁre alarm.

Internal auxiliary lock: The Auxiliary Lock is engaged when the Chexit is armed. The locking mechanism is speciﬁcally designed to hold securely even when the exit device is struck with forceful blows.

User deﬁneable rearm time: The Rearm time is the amount of time aer the device is activated before it arms. It is designed to give someone time to pass through the door before rearming oocurs. Timing can be changed by the user for any time between 2 and 28 seconds in two second increments. There is also an inﬁnite rearm setting that requires the use of an external door position switch. In this setting the door remains in the rearm mode until the door is closed. This can be useful on jet way doors in an airport.

Factory deﬁneable delay time: Most jurisdictions allow 15 seconds of delay before allowing egress. In those cases where 15 seconds is not appropriate, Von Duprin can set the Chexit for any delay time between 0 and 60 seconds on 2 second increments. For delays greater than 15 seconds a letter from the local authority is required.

Electrical options & accessories

Request to exit switch: Built into the device to detect when someone attempts to exit. Pushing the push pad when the device is armed will cause this switch to start an irreversible alarm cycle.

Nuisance alarm: When a Chexit is located in a public area, it can be desireable to limit false alarms. If the Nuisance Delay options are set to off, the device will go into alarm as soon as the push pad is touched (when armed). Turning the Nuisance Delay on will require the push pad to be pressed for 1 second before the Chexit goes into alarm. If the Nuisance Audible and Nuisance Delay are both on, the alarm will sound as soon as the push pad is pressed, but the alarm sequence will stop unless the push pad is held for 1 second or more.

Remote alarm: A relay contact is provided to give external alarm indication. This contact close when the device is in an irreversible alarm condition. This contact can be used to drive a horn, lamp, or other indicative device.

Key switch: The Key switch provides the means to arm, disarm or reset the Chexit. The key can be removed in either the Arm or Disarm position.

Indicator lamp: The status of the Chexit can be determined by the indicator lamp. When the lamp is off, this indicates the device is disarmed and is functioning as a normal exit device (no delay). A continuously on lamp indicates the device has just been armed and as soon as the selectable rearm timer expires, the device will arm. A slow ﬂashing lamp indicates the device is armed. A fast ﬂashing indicator lamp indicates the device is in alarm.

54

54 • Von Duprin 98/99 Series

98/99 Electrical options

Chexit typical application

Chexit single door with options – The Chexit is used as an access control device. The card reader allows access. Also shown in this application is an external horn and door position switch. The auxiliary horn is used for increased volume in remote locations. Using a door position switch gives added security to the opening in case the door is not reclosed.

With the Chexit disarmed, the opening functions as a normal exit device. If card readers are required on both sides of the door, the normally closed contacts of the readers should be weird in series.

Note: Chexit rim or vertical rod/cable devices lock any outside trim input when the device is in the armed condition. If access is needed from the trim side of the door, some type of electric switch would need to be tied into the external inhibit input of the device.

Chexit mortise lock device the outside trim works independently from the Chexit device.

+–

Horn

To Fire Alarm 2 x 18 ga.

2 x 18 ga. (new)

Card Reader (Inside or Outside)

Gnd

Fire Alarm

Card Reader

120 VAC 3 x 14 ga.

2 x 12 ga.

2 x 12 ga. 6 x 18 ga.

EPT KPT-10

Cable

Chexit

PS914

+24

Power Supply

Door Position Switch

2 x 18 ga.

Gnd

DPS

CM+

CM-

Chexit

Cable

+24Red

SC

FA

III

NO

C

Black

White

Yellow

Orange

Green

Gray

Violet

Blue

Brown

Horn

Power Supply

ALK Alarm kit

ALK Alarm kit is a simple yet effective way to deter unauthorized

use of an opening. While the exit device is still a means of egress, the ALK kit contains an internal horn. When the touch bar is depressed, the horn sounds to provide an audible means of signaling that the opening has been violated. The alarm kit can be armed or disarmed by key thus allowing the exit device to be set in an armed or disarmed mode. The horn is rated at 85 decibels.

For Hardware Applications

The assembly includes both a 24VDC Input and External Inhibit standard. The External Inhibit provides remote arming and dis-arming.

The key switch uses a standard 1 with a straight cam (Schlage 20-001, B502-191 cam). The unit operates on one standard 9-volt alkaline battery. When the battery is weak, the horn will emit an intermittent low battery alert signal.

The alarm can automaticaly re-arm with a 1 delay upon request.

Alarm kits are available with a choice of two switch kits, RX or LX. RX monitors the touchpad and is furnished standard. LX optional latch bolt monitoring is recommended for use with surface vertical rod exit devices or when alarm needs to sound from both the exit device and trim side of the door. Specify ALK-LX.

Note: For latch bolt monitoring on a 98/9975 with ALK, specify a SS7500 lock. LX switch not available for 98/9975 devices.

1

/4" (32mm) mortise cylinder

1

/2, 3 or 6 minute time

Electrical options & accessories

Door width reference for CX devices

Device 3' (914mm)

Length

CX98/98-F/99/99-F 2'10 1/2" (864mm) 3 '4 1/2" (1016mm)

CX9875/9875-F/9975/9975-F 2'10" (864mm) 3'4" (1016mm)

CX9827/9827-F/9927/9927-F 2'10" (864mm) 3'4" (1016mm)

CX9857/9857-F/9957/9957-F 2'10" (864mm) 3'4" (1016mm)

CX9847/9847-F/9947/9947-F 2'10" (864mm) 3'4" (1016mm)

CX9848/9848-F/9948/9948-F 2'10" (864mm) 3'4" (1016mm)

CX9849/9849-F/9949/9949-F 2'10" (864mm) 3'4" (1016mm)

CX-R 98/9927 2'4" (838mm) 2'10" (1041mm)

CX-R 98/9947 2'4" (838mm) 2'10" (1041mm)

CX-R 98/9947-F 2'5" (864mm) 2'11" (1016mm)

CX-R 98/9947WDC 2'5" (864mm) 2'11" (1016mm)

CX-R 98/9975 2'5" (864mm) 2'11" (1016mm)

4' (1219mm) Length

The ALK is available in two styles, 99ALK, grooved cover and 98ALK, smooth cover.

The ALK includes a 6" x 20" decal for application on door “EMERGENCY EXIT ONLY. ALARM WILL SOUND. ”SS push bar trim can be used instead of the door decal, specify SS push bar trim when ordering the device.

When the ALK is used, standard dogging is removed. If cylinder dogging is required there are two choices. Special center case dogging is available or for 3' or 4' doors. The ALK can be moved to the hinge side of the device and standard cylinder dogging can be added.

To Order, Specify:

1. Standard, 98 ALK

2. Cylinder Dogging, CD98 ALK

3. Special center case dogging, SD98 ALK

4. If AR desired, specify AR 1.5, 3 or 6

Minimum door opening sizes on ALK applications

Device 3' (914mm)

Length

98/98-F/99/99-F 2'10" (864mm) 3'4" (1016mm)

9875/9875-F/9975/9975-F 2'10" (864mm) 3'4" (1016mm)

9827/9827-F/9927/9927-F 2'10" (864mm) 3'4" (1016mm)

9857/9857-F/9957/9957-F 2'10" (864mm) 3'4" (1016mm)

9847/9847-F/9947/9947-F 2'9" (838mm) 3'3" (991mm)

9848/9848-F/9948/9948-F 2'9" (838mm) 3'3" (991mm)

4' (1219mm) Length

Von Duprin 98/99 Series • 55

55

98/99 Electrical options

Electrical options & accessories

E Electric mortise lock device

The electric mortise lock device has all the versatility and advantages of the standard mortise lock device, plus the advantage of being electrically controlled by a remote switching device, an access control system or an automatic ﬁre alarm system. The device features the E7500 mortise lock. The E7500 controls the locking of the outside trim. When unlocked, the door remains latched, preserving the ﬁre rating of the door and making it particularly useful where codes permit locking but require unlocking during a ﬁre emergency. The outside trim cylinder retracts the latch bolt for mechanical override, night latch function. Only available with TP, K or L functions.

The E7500 lock contains a SPDT signal to monitor the outside trim condition (locked or unlocked) and a second SPDT signal switch to monitor the latch bolt.

Standard features:

• Field reversible handing

• 24 VDC continuous duty solenoid

Optional features:

• Fail safe (locked when energized, unlocked when de-

energized or during power failure). Specify with sux “FS.”

• Fail secure (unlocked when energized, locked when de-

energized or during power failure). Specify with sux “FSE”

• 24 VAC (with SO option)

• 12 VDC

• 12 VAC (with SO option)

Note: Some Fire codes will require “Fail Safe” (FS) operation for stairwell doors.Be sure to specify the correct operation for your application.

Electrical speciﬁcations:

• Solenoid — .60 AMPS @ 12VDC

.30 AMPS @ 24VDC

• Each switch — Up to 2.0 AMPS @ 24VDC Maximum

The E option does not include the power transfer from door to frame, the power supply or the control operator. (Refer to EPT-10 and PS902 or PS914 power supply)

To order, specify:

1. Use preﬁx “E,” example E9975.

2. FS or FSE

3. Voltage and current.

Electric mortise lock device

Adaptable for openings where continuous latching is required while the trim may be electrically locked or unlocked from a remote location—stairwells, exterior doors, etc.

Minimum system requirements:

• PS902

• EPT-10

Allegion Connect

Allegion’s cross-category Connect features common interconnect components to our electriﬁed options. Allegion Connect is a quick and easy way to connect power sources; all the way from your power supply to locking device. There is no wire cutting; reducing installation and maintenance time ultimately cutting cost. Aer installation, Allegion’s Connect continues to provide beneﬁts throughout the lifetime of the opening by offering a service kit for repairs or modiﬁcations in the future.

Features and beneﬁts

• Quick: common connections reducing installation time

• Perfect Connections: these factory installed connectors

ensure the right wires match up every time

• Protective: the connectors protect the connection points

throughout the installation process and lifetime of the opening

• Interchangeable: all Allegion Connect products utilize the

same connectors

• Maintenance: you no longer need to cut away wire to

disconnect Allegion products, also available is a service kit speciﬁcally for Connect products.

Harness length

6 Inches CON-6 CON-6P 12 Inches CON-12 CON-12P 26 Inches CON-26 CON-26P 32 Inches CON-32 CON-32P 38 Inches CON-38 CON-38P 44 Inches CON-44 CON-44P 50 Inches CON-50 CON-50P 192 Inches CON-192 CON-192P

Power Supply Wire Harness = Connectors on one end, stripped leads on the other end, offering a direct connection to the power supply

6 Inches CON-6W - wire extension to power supply

Consult door manufacturer for harness length requirements.

Note: You will need to purchase a separate wiring harness to go from exit device to hinge/ EPT and an additional harness to go from hinge/EPT to power supply or access control system. Harness part numbers with ordering information can be located in the Schlage, Von Duprin and Falcon pricebooks. A service kit is available for order in the Schlage, Von Duprin and Falcon pricebooks. Included in this kit are male end plugs, female end plugs and pins to customize harnesses to your application.

Note: Must be ordered with exit devices and locks

Connectors on both ends

Connectors on one end, crimped pins on the other end

How to order

1. Specify CON for Connect electronic options Example: EL-99-EO-CON (99 Series Electriﬁed Latching exit only with Connect connectors)

2. Specify harness length; Consult door manufacturer for harness length

3. Specify Von Duprin EPT10-CON or Ives 7200 power transfer hinge

Wire run options

56

56 • Von Duprin 98/99 Series

98/99 Electrical options

PS872 Wiring

EL Electric latch retraction

The EL feature allows for the remote unlatching of exit devices. A control station operator can ﬂip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. A powerful, continuous duty solenoid retracts the latch bolt, either for momentary unlatching, or for extended periods of time. The EL feature is an alternative to manual dogging.

If manual hex-key dogging is required, specify HD-EL. If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify SD-EL. SD-EL is not available on the 9875 or 9975 devices.

EL devices are also useful with automatic door operators, and may be applied to ﬁre-rated applications when under the control of an automatic ﬁre alarm system.

UL approved for Class II circuit applications.

The EL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS914 power supply.

The PS914 with the 9002RS option card is the minimum option card required. Other option cards available for other functions, see PS914 power supply for additional information.

Solenoid speciﬁcations: Solenoid resistance:

Continuous duty – 24 VDC -grn-yel 1.2 – 2.2 OHMS Current inrush – 16 Amps -grn-org 100 – 150 OHMS Current holding – 0.3 Amps

To order, specify:

Standard – use preﬁx EL, example EL99L. Hex Key dogging – Use preﬁx HD-EL, example HD-EL99L special center case dogging – Use preﬁx SD-EL, example SD-EL99L

Popular EL application

Power supply PS914-2RS Electric power transfer EPT-2 or EPT-10

120/240

VAC

SC I1 O1 I2 O2 GND

a*

b*

EPT-2

EL #2

EL #1

Input #2

(Required for independent operation only).

a*

Input #1

Von Duprin exit device

EL 98/99 Rim

*

a

All other 98/99EL device types

*

Control Switch 0-1200 18

b

1. Wire lengths include an EPT, Door loop, electric hinge or pivot and are measured one way between the PS914/option board and the device.

2. Table is applicable to devices that have shipped aer August 2012.

EL Wire length (feet)

0-500 12 0-300 14 0-200 16

0-250 12 0-150 14 0-100 16

1

Wire gauge (AWG)

QEL Quiet electric latch retraction

The QEL feature allows for the remote unlatching of exit devices. A control station operator can ﬂip a switch to retract the latch bolt and immediately change an exit door to push-pull operation. Different than the popular EL, the QEL quiet operation is achieved using an electric drive motor which retracts the latch bolt either momentary unlatching or for extended periods of time. This feature is an alternative to manual dogging.

If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify

SD-QEL. SD-QEL is not available on the 9875 or 9975 devices.

QEL devices are also useful with automatic door operators, and may be applied to ﬁre-rated applications when under the control of an automatic ﬁre alarm system.

UL approved for Class II circuit applications.

The QEL option does not include the power transfer from door to frame, the power supply, or the control operator. Refer to EPT-2 power transfer and the PS902 or 914 power supply.

The PS902/914 with the 2RS, 4RL or 4R board is the minimum required. Other option boards available for other functions, see PS902/914 power supply for additional information.

QEL Electrical load

Voltage 24VDC Current 1.4 A Inrush (0.5 sec.)

To order, specify:

Standard — use preﬁx QEL, example QEL99L. Special center case dogging — use preﬁx SD-QEL, example SD-QEL99L

120/240

VAC

SC I1 O1 I2 O2 GND

0.14 A Holding

2.0 A Calibrate (3 sec. one time)

Popular application

Power supply PS902-2RS Electric power transfer EPT-2 or EPT-10

EPT-2

QEL #2

QEL #1

Input #2

(Required for independent operation only).

Input #1

a*

b*

EPT-2

a*

b*

*

a

Distance (one-way)

200´ 18 AWG 320´ 16 AWG 500´ 14 AWG 800´ 12 AWG

*

b

Wire selection

1200 . Max. 18 gauge standard

Switch wire size

Wire gauge

Von Duprin 98/99 Series • 57

Electrical options & accessories

57

Electrical options & accessories

98/99 Electrical options

Power Supplies

Series PS902/914

Overview:

The PS900 Series is a consolidated line of power supplies and accessories that offer enhanced ﬂexibility and functionality speciﬁc to the changing needs of the access control market. The PS900 Series can be used in a variety of applications to convert high voltage AC power into the low voltage DC outputs required by most access control devices. The PS900 Series protects devices downstream by providing Class 2*, ﬁltered and regulated power. The full line is UL294 certiﬁed.

Note: PS906 can provide Class 2 rated outputs when used with 900-8P distribution board.

Features:

• Constant output rating at both 12 VDC and 24 VDC provides

superior performance ; includes ﬁeld selectable jumper

• Polarized connectors for option boards eliminate need for

racks and side connectors

• Flat mounting of option boards provides easier access to

terminal blocks for connection of electriﬁed devices

• High voltage protective cover

• Battery back-up board auto-selects voltage

• Fire alarm relay can be conﬁgured to provide either switched

or un-switched outputs from a power supply

• PS914 designed with high in rush current for powering

electriﬁed panic devices

• Universal 120-240 VAC input

• Low voltage DC, regulated and ﬁltered

• Electronic power limiting foldback circuit for AC current

overload protection

• Fused primary input

• AC status monitor- isolated SPDT contacts

• AC input and DC output LED status indicators

• Cover mounted AC input indication

• Hinged cover with lock down screws

PS902 PS904 PS906 PS914

Number of connectors on power supply for the following:

Distribution boards 1 2 3 2 Battery back-up board

Note: One ﬁre alarm board can be connected directly to the PS902. If a ﬁre alarm board is desired for the PS904, PS906 or PS914 it can be connected to a distribution board.

2 amps 4 amps 6 amps 4 amps

1

1 1 1

Applications:

The PS900 Series of power supplies works with many electriﬁed devices including Schlage electromagnetic locks, Schlage AD-Series hardwired locks, Schlage electriﬁed mechanical locks, Von Duprin electriﬁed strikes , Von Duprin exit devices, and many other brands.

Accessories:

The Schlage PS900 Series features seven option boards for use in a variety of applications. All Schlage PS900 Series power supplies option boards are UL 294 certiﬁed.

Option boards:

900-4R: 4 relay controlled output board to power multiple

devices

900-4RL: 4 relay distribution board with logic is ﬁeld conﬁgurable for time delay function, auto operator, security interlock

900-8F: Provides 8 individually fuse-protected outputs, giving the ﬂexibility to power multiple devices and provide another layer of protection

900-FA: Emergency interface relay integrates with ﬁre alarm and is used to cut power in case of emergency

900-BB: Battery backup

900-2RS: 2 relay EL panic device control board (PS914 only)

900-BBK: Battery backup kit includes two 7A/hr batteries and

provides up to four hours of backup power when cycled every 5 minutes at full load

Certiﬁcations:

• UL 294 certiﬁed—the standard for access control

• Class 2 rated*

* Except PS906, output rating exceeds Class 2 power limits

Once power is converted to low voltage DC, the PS900 Series offers a variety of distribution options, including basic fuse protection, simple relay, and advanced logic providing complex sequencing and timing functions.

* PS906 can provide Class 2 rated outputs when used with 900-8P distribution board.

58

58 • Von Duprin 98/99 Series

98/99 Electrical options

EPT Electrical power transfer PNT Pneumatic transfer

Electric Power Transfer provides a means of transferring electrical power from a door frame to the edge of a swinging door. The units are completely concealed when the door is in the closed position, and are ideal for installations involving abuse or heavy trac.

Two models are available; EPT-2, two 18 gauge wires and EPT-10, ten 24 gauge wires. The EPT-2 and EPT-10 are U/L listed as “miscellaneous door accessory”.

UL Listed for use on ﬁredoors

Door applications:

up to 5" butt hinges – 180˚ swing,

1

5

/2" butt hinges – 130˚ swing,

6" butt hinges – 110˚ swing,

3

/4" butt offset pivots 180˚ swing.

Not for use with swing clear hinges or center-hung pivots.

Finishes

SP28 (sprayed aluminum)

SP313 (sprayed duranodic).

Electrical options & accessories

Dimensions

Housing

EP T-2 Two 18 gauge wires, Up to 2 AMPS @ 24VDC, with

EPT-10 Ten 24 gauge wires, Up to 1 AMPS @ 24VDC, with a

PNT-1

To order, specify:

1. EPT-2 ,EPT-10 or PNT-1.

2. Finish, SP28 or SP313.

¹|₄" x 1⁵|₈" (229mm x 32mm x 38mm)

9" x 1

a 16 AMPS Maximum Surge

16 AMPS Maximum Surge

⁵|₃₂" Tubing

E996L Electriﬁed breakaway lever

E996L electriﬁed lever trim provides remote locking and unlocking. Furnished standard in fail safe (FS) condition, can be ﬁeld converted to fail secure (FSE) where allowed. E996L is furnished standard with cylinder operation for nightlatch (NL) function, or with blank escutcheon (BE).

Von Duprin 98/99 Series • 59

59

98/99 Mechanical options

Mechanical options & accessories

AX Accessible device

The AX device is a UL certiﬁed exit device designed to meet the progressive requirements of the California Building Code for accessible openings. This device meets the 5 lbs of operating force requirement called for in chapter 11B-309.4. The AX device also exceeds ANSI/BHMA requirements. Available devices include: AX98/99, AX98/99-F, AX98/9949LBL, AX98/9949-F LBL, AX98/9949-F LBLAFL. Additionally, all AX devices will be shipped with a new UL label clearly stating “Meets California building Code (2013) Sec. 11B-309.4” and an “AX” identiﬁer label on device center case. See images below for reference.

XP Extra performance

For increased security the XP98/99 Rim exit device has a static load force resistance of more than 2,000 pounds, twice that of standard rim exit devices. The two-piece latch bolt forms a 90 strike contact. The “smart” latch changes shape when subjected to external forces. This design enables the exit door to withstand an external attack and remain secure. Additionally, the patented latch bolt design provides a greater, longer-lasting latch bolt to strike contact which is not easily affected by the twisting motion of a weakened frame, resulting in an opening that will remain strong.

With a door loaded to 250 pounds, XP98/99 requires less than 40 pounds of pressure to open, 25% less than the safety code requires.

XP98/99 is available for panic or ﬁre exit hardware applications. Dimensions, ﬁnishes and trim options are equal to the standard 98/99 series rim exit device.

Note: The 909 strike is to be used for all applications. The exception occurs with the use of ﬁre rated double door applications, in this instance the 954 strike is required.

°

latch-to-

WS Surface vertical rod one-point and three-point exit devices

WS Multi-point exit devices for tornado application devices WS98/9927 (one- point) and WS98/9957 (three-point) surface vertical rod exit devices are designed, tested and certiﬁed to comply with the Federal Emergency Management Agency's publication FEMA 361- Design and Construction Guidance for Community Safe Rooms.

UL Listing – panic hardware UL 305; and ﬁre exit hardware UL 10C: WS98/9927:

3 hour pairs of doors double egress, 90 minutes swinging same direction, 8'0" x 8'0" BHMA Grade 1, ANSI A156.3-2001

WS98/9957:

3 hours single doors, 4'0" x 8'0" BHMA Grade 1, ANSI A156.3-2001

Windstorm ratings: WS98/9927:

Miami-Dade County/FBC compliance to TAS 201, TAS 202, TAS 203; design load rating +150/-150 PSF

WS98/9957:

UL-FEMA 361 certiﬁed 4'0" x 8'0" single ﬂush hollow

These devices are listed with Steelcra Paladin for tornados, and Steelcra H-Series doors hurricane applications.

To order, specify: WS preﬁx, example WS9927-F

(245 MPH wind zone); Enhanced Hurricane Protection (EHPA) ASTM E1996, ANSI/ICC 500 (245 MPH wind zone).

UL-FEMA 361 certiﬁed 8'0" x 8'0" pairs, swinging same direction and 4'0" x 8'0" single non-ﬁre rated ﬂush hollow metal. UL-ANSI/ICC 500 certiﬁed for F5 tornado applications.

metal (ﬁre-rated and panic). UL-ANSI/ICC 500 certiﬁed for F5 tornado applications.

™

PW-Series doors

LBR Less bottom rod, panic and ﬁre rated

LBR option is available, using a spring loaded auxiliary latch bolt installed in the lower door edge. When exposed to heat the auxiliary latch bolt releases, keeping the doors in alignment and closed during a ﬁre. UL listed 3 hours on hollow metal doors double egress, 90 minute swinging same direction, and 20 minutes wood doors (consult wood door manufacturer). Fits door stiles as narrow

5

as 3

/8".

LBR devices must be ordered in pairs or must be used in conjunction with an approved automatic or constant latching ﬂush bolt.

PL Pullman latch

When PL is speciﬁed the standard latches are replaced with pullman style latches. Pullman latches are always extended and are most commonly used in conjunction with electric strikes and LBR-less bottom rod application. Not available with Fire rated devices.

Not recommended where security is of the utmost importance since latches do not deadlock.

60

60 • Von Duprin 98/99 Series

98/99 Mechanical options

Dummy pushpad

The 330 dummy pushpad is designed as a companion unit for all 99 devices. The 350 dummy pushpad is a companion unit for all 98 devices. The pushpad is rigid or nonfunctioning. A push/pull operation can be accomplished by using 990DT, 996DT trim or any Ives Pull.

The 330/350 can be equipped with a functional pushpad and will accommodate an RX or WP-RX switch. Specify RX-330. May also be equipped with the RX2, double RX switch. Specify RX2-330

To order, specify:

1. 330 or 350.

2. Size 3' or 4' (914mm or 1219mm)

3. Finish, US3, US4, US10, US26, US26D, US28, 313 & 315. US32D – 350 only.

4. Speciﬁy RX, WP-RX or RX-2 if desired.

SG Safety glow

Self-illuminating touchpad deﬁnes the location of the exit door in dark or smoke-ﬁlled area. The safety glow coating is a special powder coat ﬁnish that glows brightly during low or no light conditions. This coating was developed to meet MEA standards where luminescent exit door markings are required in commercial facilities. There are no batteries or electronics, the coating is charged when exposed to light.

To order, specify: Sux SG, EL 9927L-SG

RSS Red Silk Screen

Red silkscreen lettering on touchpad trim. - "Emergency Exit Only, Push To Open And Sound Alarm". This comes standard on SS devices.

To order, specify: Sux RSS, 9927L-RSS RHR

Mechanical options & accessories

Braille, embossed and knurled touchpads

* Image shown is a special order.

Braille touchpad embossed with the standard message “CAUTION STAIRWELL” in braille and raised letters provides assistance to persons with impaired vision. Letters are (13mm) high and braille is #2, raised height is messages are available on special order, limited to 20 characters per line.* To order, specify: Sux BR, EL9927L-BR

Embossed touchpad is embossed with the word “PUSH”. To order, specify: Sux EMB, EL9927L-EMB

Knurled touchpad is to provide warning to persons with impaired vision. To order, specify: Sux PBKN, EL9927L-PBKN

Consult factory for availability.

3

/32" (2mm). Other

1

/2"

Von Duprin 98/99 Series • 61

61

98/99 Mechanical options

PN Pneumatic controlled exit devices

The PN feature provides remote latch bolt retraction in hazardous areas where electrically operated devices would not be permitted. The pneumatic solenoid will retract the latch bolt for momentary or prolonged periods. PN exit devices are particularly suited for use with automatic door operators. The PN feature is available on both Panic and ﬁre exit hardware devices.

The PN feature includes a special actuating linkage that gives building owners the option of mechanically or pneumatically dogging the exit device. If manual hex-key dogging is required, specify HD-PN (Dogging the device, whether mechanically or pneumatically, makes the device function as a push/pull unit and reduces the wear on its moving parts.) If cylinder dogging is required, the standard cylinder dogging is not available, but special center case dogging is available, specify SD-PN. SD-PN is not available on the 9875 or 9975 devices.

When activated pneumatically, the latch bolt(s) of the exit device retract in uses air pressure ranging from 50 to 100 pounds per square inch.

This product will function only when it is part of a pneumatic system (air compressor, air lines, pneumatic system, etc.).

Contact LCN for correct control boxes.

To order, specify:

• Standard — Use preﬁx PN, example PN99NL

• Hex Key Dogging — Use preﬁx HD-PN, example HD-PN99NL

• Special Center Case Dogging (handing is required, specify

RHR or LHR) — Use preﬁx SD-PN, example SD-PN99NL

1

/2₂ to 11/2 seconds. This pneumatic operation

Mechanical options & accessories

PNT pneumatic transfer

Pneumatic controls

PNT-1 is available for pneumatic latch retraction exit devices. Appearance and dimensions are identical to EPT models.

62

62 • Von Duprin 98/99 Series

98/99 Device options & accessories

RG-27 Vertical rod and latch guard

Series RG-27 Vertical rod and latch guards protect the bottom rods of exit devices from the damaging impacts of carts or gurneys passing through doors. (If bottom rods become damaged, the exit device will not function as intended and can jeopardize the ability to exit safely during an emergency.)

In addition to protecting the vertical rod, the guard provides a smooth, unobstructed surface so the door can be pushed open easily with the bumpers of a wheelchair. The latch guard portion is 10" high. The

36"

standard latch guard features a 45° ramp. The extended latch guard offers a continuous ramp in 3' or 4' widths.

All stainless steel construction in US32D ﬁnish. Latch guards can cover latches as large as

1

/4"W x 10"H x 1 7/8" projection.

Rod guard

Latch guard

Extended latch guard

997 Cover plate kit

For 98/99 rim device, kit contains inside and outside plates for hinge stile cutouts, an inside plate for the lock stile, and necessary screws. Plates are designed to cover cutouts

9"

(229mm)

required by most existing exit device installations. Specify ﬁnish.

WDA Cover plate kit

For wood door applications, used to cover up door preparations for control, also prevents the control from boring into the wood door. Finished to match control.

#10WDA Cover plate kit for 370 series controls

7 7/8"

13/4" (44mm)

Device options & accessories

7 7/8"

10"

4 3/8"

12"

3' or 4'

2 1/4"

Models

RGO Rod guard only (projection 1

3

/16")

RG-27 Rod and latch guard

RG-27-3 3' (914mm) Rod guard and extended latch guard

RG-27-4 4' (1219mm) Rod guard and extended latch guard

LGO Latch guard only

LGO-3 3' (914mm) Extended latch guard only

LGO-4 4' (1219mm) Extended latch guard only

When using on wood ﬁre doors, high density block is required.

To order, specify:

1. Model number.

2. Handing (except on RGO).

3. Door material if other than hollow metal.

4. Optional sex bolt mounting available.

#33A-WDA Cover plate kit for 360 series controls

2 1/16"

GBK Glass bead kit

Glass bead conversion kits are available for all 98/99™ Series devices for use on doors with raised glass beads. Each kit consists of ships with

To order, specify:

1. 99GBK

2. Device type (rim, mortise, surface vertical rod, concealed

3. Wood door, when used with concealed vertical Rod

4. When used with 330/350 Dummy pusher, order two hinge stile shims.

1

/4" (6mm) shim sets. GBK for surface vertical rod

1

/8" shims for rod guides.

vertical rod)

Von Duprin 98/99 Series • 63

63

98/99 Device options & accessories

Cylinders

Cylinders are not furnished with device or trim and must be speciﬁed when ordering. Refer to trim pages for cylinder type.

Mortise — 3215 (Schlage 20-001, B502-191 cam) Rim — 3216 (Schlage 20-022 cam)

Device options & accessories

Dogged (inverted) cam

For cylinder dogging or 360L

Undogged cam (standard operations)

For standard trim functions or 360L-NL

64

64 • Von Duprin 98/99 Series

98/99 Device options & accessories

Mullions

Removable steel mullions provide single door performance in double door openings with rim devices. Mullions are easily removed by loosening bottom set screw and removing top ﬁtting cover. The top mullion ﬁtting is attached to the frame and is concealed by the ﬁtting cover.

Steel mullions are 2" (51mm) wide and 3" (76mm) deep, with a wall thickness of

Mullions are shipped with mounting screws and prepared for strikes. Strikes are not included except where indicated.

Steel mullions are available in SP28 and SP313 ﬁnishes. Consult factory for other powder coat ﬁnish options.

KR – Keyed removable steel mullions make removal faster and easier by a single operation of the mortise cylinder. Once mullion is removed, large equipment or furniture can freely pass through the opening. The unit will self lock when reinstalled, without the use of the cylinder key. Uses a 1 mortise cylinder with a straight cam (Schlage cam reference B502-191). Cylinders are sold separately. Preﬁx mullion model with “KR”.

Removable aluminum mullions are 1 closest to the door and 2 depth is 3

1

/8" (79mm) with a wall thickness of 1/8" (3mm).

Aluminum mullions are available in US4, US10, US28, 313 and 315 ﬁnishes. Consult factory for other powder coat ﬁnish options. Aluminum mullion are not available keyed removable.

Stock hollow metal applications for devices mounted to cover ANSI 161 cutouts are higher than the standard mullion strike location. Consult the factory for special strike preparation or order a blank mullion. See below.

Blank mullions are furnished without strike preparation. They are used to mount devices at a strike height different from the standard mullion preparation.

To order, specify:

1. For keyed Removable option on steel mullions, preﬁx model number with “KR”

2. Model number

3. Height of opening

4. Finish

5. Handing if required

6. Centerline deviation (refer to device template for standard centerline)

7. Strikes, when required, should be ordered with device

1

/8" (3mm).

1

3

/8" (60mm) at the widest point. The

/16" (27mm) wide on face

1

/4"

Removable mullions Keyed removable steel mullions

Steel mullions

1654 Prepared for two 1606 strikes. If 1606 strikes are not

4954 Prepared for 264 or 299 strikes. For use with all Von

9954 Prepared for and must be used with two 268 strikes

98-F and 99-F devices are

Note: If 268 or 499F strikes are not speciﬁed on the order, two per mullion will be added. Additional charges apply.

4754 Prepared for two 4263

4854 Prepared for one 299 and

9854 Prepared for one 268 or

speciﬁed on the order, two per mullion will be added. Additional charges apply.

Duprin Panic rim devices.

(88-F device), or two 499F (22-F, 98-F, 99F devices). UL ﬁre labeled mullion for up to 3 hour opening using Von Duprin ﬁre exit rim devices. This mullion is not easily removed due to special ﬁttings.

rated up to 10'0" (3048 mm).

monitor strikes.

one 6111 electric strike. Indicate handing for electric strike.

499F strike and one 6111 electric strike. Indicate handing for electric strike. UL ﬁre labelled mullion for up to 3 hour openings up to 8' x 8' (2438mm x 2438mm) using Von Duprin ﬁre exit rim devices

Device options & accessories

Von Duprin 98/99 Series • 65

65

98/99 Device options & accessories

Device options & accessories

Sex bolts

Sex bolts when ordered with devices may be furnished with screw lengths different than shown in Column B. Below, Column B indicates popular sizes. Sex Bolts ordered separately are not furnished with screws. If screws are required refer to chart below and order screws by description as a separate item. Other screw lengths may be used based on minimum and maximum allowable thread engagement, shown in column “C.” Quantity required — refer to device section, quantities differ depending on outside trim.

Rim, mortise and concealed vertical

Center case Hinge case

Device type

98, 9827, 9827-F, 9875, 9875-F, 9847, 9847-F, 9847WDC, 9849, 9849-F 99, 9927, 9927-F, 9975, 9975-F, 9947, 9947-F, 9949, 9949F, 98/9949WDC, 98/9949WDC-F

98-F, 99-F

* For use with outside trims, see page XX for details

*

Door thickness Sex bolt B

no. A Screw no. A Screw

3

/4" (44mm) 425 1 9/16" 10-24 x 1" PPHMS

1

2 1/4" (57mm) 425 1 9/16" 10-24 x 1 1/2" PPHMS9/32" – 1 9/16" 425 1 9/16" 10-24 x 11/2" PPHMS9/32" – 1 9/16"

9

10-24 x 1" PPHMS

/16"

1

1 3/4" (44mm)

1

/4" (57mm)

2

425 825A*

425 825B*

13

/16"

1

1 2

10-24 x 3/4" PPHMS

9

10-24 x 1

/16"

5

/16"

10-24 x

1

/2" PPHMS

3

/4" PPHMS

325 sex bolts used on surface Vertical Latches.

425 sex bolts are required for 98/99 Series ﬁre rated devices when used on wood door applications. When wood doors are speciﬁed for these devices, sex bolts will be added to the device application unless SLM blocking package is speciﬁed.

825 sex bolts are required with 98-F/99-F rim devices on wood door applications using NL, TP, K and L outside trims. Two 825 sex bolts will be added to the device application unless

325

SLM blocking package is speciﬁed.

To order, specify:

1. Model number

425

2. Quantity (2 per package)

3. Finish

4. Door thickness other than 1

C Thread engagement min. – max

9

/32" – 1 9/16" 425 1 9/16" 10-24 x 1" PPHMS

9

/32" – 1 9/16" 425 1 9/16" 10-24 x 3/4" PPHMS ⁹9/32" – 1 9/16"

9

/32" – 1 9/16" 425 1 9/16" 10-24 x 11/4" PPHMS9/32" – 1 9/16"

Sex bolt B

3

/4" (44mm)

825

C Thread engagement min. – max

9

/32" – 1 9/16"

Surface vertical rod - latches only

Device type

9827/9927/9827F, 9927F

PPHMS – Pan phillips head machine screw UFPHMS – Undercut ﬂat phillips head machine screw

* For use with outside trims.

66

66 • Von Duprin 98/99 Series

Latch case

Door thickness Sex bolt B

no. A Screw

3

/4" (44mm) 325 1 9/16"1/4 - 20 x 3/4" FPHMS

1

/4" (57mm) 325 1 9/16"1/4 - 20 x 1/4" FPHMS

2

98/99 Function, grade, type options

ANSI Function, grade & type

Function Grade 1,

1

2

3

5

7

8

10

11 12

14

16

type 1

98EO & F 99EO & F

98DT 99DT

98NL & F 99NL & F

98K-NL & F 99K-NL & F

98L-NL & F 99L-NL & F

98TP & F 99TP & F

98TP-2 & F 99TP-2 & F

98K & F 99K & F

98L & F 99L & F

98K-2 & F 99K-2 & F

98L-2 & F 99L-2 & F

98K-BE & F 99K-BE & F

98L-BE & F 99L-BE & F

Grade 1, type 2

9827EO & F 9927EO & F

9827DT 9927DT

9827NL & F 9927NL & F

9827K-NL & F 9927K-NL & F

9827L-NL & F 9927L-NL & F

9827TP & F 9927TP & F

9827K & F 9927K & F

9827L & F 9927L & F

9827TL & F 9927TL & F

9827K-BE & F 9927K-BE & F

9827L-BE & F 9927L-BE & F

9827TL-BE & F 9927TL-BE & F

Grade 1, type 3

9875EO & F 9975EO & F

9875DT 9975DT

9875NL & F 9975NL & F

9875K-NL & F 9975K-NL & F

9875L-NL & F 9975L-NL & F

9875TP & F 9975TP & F

9875TP-2 & F 9975TP-2 & F

9875K & F 9975K & F

9875L & F 9975L & F

9875K-2 & F 9975K-2 & F

9875L-2 & F 9975L-2 & F

9875K-BE & F 9975K-BE & F

9875L-BE & F 9975L-BE & F

Grade 1, type 7

9847WDCEO & F 9947WDCEO & F

9847WDCDT 9947WDCDT

9847WDCNL & F 9947WDCNL & F

9847WDCK-NL & F 9947WDCK-NL & F

9847WDCL-NL & F 9947WDCL-NL & F

9847WDCTP & F 9947WDCTP & F

9847WDCK & F 9947WDCK & F

9847WDCL & F 9947WDCL & F

9847WDC & F 9947WDC & F

9847WDCK-BE & F 9947WDCK-BE & F

9847WDCL-BE & F 9947WDCL-BE & F

9847WDC & F 9947WDC & F

Grade 1, type 7

9849WDCEO & F 9949WDCEO & F

9849WDCDT 9949WDCDT

9849WDCNL & F 9949WDCNL & F

9849WDCK-NL & F 9949WDCK-NL & F

9849WDCL-NL & F 9949WDCL-NL & F

9849WDCTP & F 9949WDCTP & F

9849WDCK & F 9949WDCK & F

9849WDCL & F 9949WDCL & F

9849WDC & F 9949WDC & F

9849WDCK-BE & F 9949WDCK-BE & F

9849WDCL-BE & F 9949WDCL-BE & F

9849WDC & F 9949WDC & F

Grade 1, type 8

9847EO & F 9947EO & F

9847DT 9947DT

9847NL & F 9947NL & F

9847K-NL & F 9947K-NL & F

9847L-NL & F 9947L-NL & F

9847TP & F 9947TP & F

9847K & F 9947K & F

9847L & F 9947L & F

9847TL & F 9947TL & F

9847K-BE & F 9947K-BE & F

9847L-BE & F 9947L-BE & F

9847TL-BE & F 9947TL-BE & F

Grade 1, type 8

9848EO & F 9948EO & F

9848DT 9948DT

9848NL & F 9948NL & F

9848K-NL & F 9948K-NL & F

9848L-NL & F 9948L-NL & F

9848TP & F 9948TP & F

9848K & F 9948K & F

9848L & F 9948L & F

9848 & F 9948& F

9848K-BE & F 9948K-BE & F

9848L-BE &F 9948L-BE & F

9848 & F 9948 & F

Grade 1, type 8

9849EO & F 9949EO & F

9849DT 9949DT

9849NL & F 9949NL & F

9849K-NL & F 9949K-NL & F

9849L-NL & F 9949L-NL & F

9849TP & F 9949TP & F

9849K & F 9949K & F

9849L & F 9949L & F

9849 & F 9949& F

9849K-BE & F 9949K-BE & F

9849L-BE &F 9949L-BE & F

9849 & F 9949 & F

Grade 1, type 9

9857EO & F 9957EO & F

9857DT 9957DT

9857NL & F 9957NL & F

9857K-NL & F 9957K-NL & F

9857L-NL & F 9957L-NL & F

9857TP & F 9957TP & F

9857K & F 9957K & F

9857L & F 9957L & F

Additional information

9857TL & F 9957TL & F

9857K-BE & F 9957K-BE & F

9857L-BE & F 9957L-BE & F

9857TL-BE & F 9957TL-BE & F

Dimensions

Von Duprin 98/99 Series • 67

67

UL Listing for ﬁre exit hardware

UL Listed ﬁre exit hardware label and opening size

Double door

Exit device

98-F 99-F

9875-F 9975-F

9827-F 9927-F

9827LBR-F 9927LBR-F

9857-F 9957-F

9847-F 9947-F

9847LBR-F 9947LBR-F

9848-F 9948-F

9849-F 9949-F

9849LBL-F 9949LBL-F

* Currently, no door manufacturers offer a listing over 90 minutes with doors swinging same direction.

Consult wood door manufacturers for current UL listings.

Door material Single door

Metal

Metal — — — — —

Metal

Metal — — — — —

3 Hour 4' x 10'

—

3 Hour 4' x 8'

With 9954 mullion

3 Hour 8' x 10'

— — — — —

— — — —

3 Hour 8' x 8'

With 9854 mullion

3 Hour 8' x 10'

3 Hour 8' x 8'

With kr9954 mullion

3 Hour 8' x 8'

With kr9854 mullion

3 Hour 8' x 8'

V x v same direction

— — —

90 Minute 8' x 10'

— — —

90 Minute 8' x 10'

*

V x mortise same direction

3 Hour 8' x 10'

—

3 Hour 8' x 10'

—

3 Hour 8' x 10'

—

V x v double egress

—

3 Hour 8' x 10'

Additional information

68

68 • Von Duprin 98/99 Series

98/99 Finishes

A. Center case cover

B. Touch bar end cap C. Touch bar trim

D. Cover plate

F. Mechanism case

E. Mechanism end cap

Finishes

Color

US number

Bright brass US3 605 Bright brass Bright brass US3, 605 Buffed anodized Satin brass US4 606 Bright brass Satin brass US4, 606 Anodized Satin bronze US10 612 Plated Satin bronze US10, 612 Anodized Bright chrome US26 625 Plated Bright stainless steel US32, 629 Buffed anodized Satin chrome US26D 626 Plated Satin stainless steel US32D, 630 Anodized Satin stainless steel

*

US32D 630 Stainless steel Satin stainless steel US32D, 630 Anodized Aluminum, anodized US28 628 Powder coat Satin stainless steel US32D, 630 Anodized Duranodic dark bronze 313 710 Powder coat Powder coat Powder coat Black 315 622 Powder coat Powder coat Powder coat

BHMA number

A, B, E C D & F

Special Finishes

Color

US number

Satin bronze, oil-rubbed US10B 613 Oil-rubbed, US10B Oil-rubbed, US10B Powder coat

Powder coat

**

RAL # – Powder coat

Bright bronze US9 611 Plated Bright bronze US9, 611 Buffed anodized Satin nickel

*

US15 619 Plated, clear powder Satin stainless steel US32D Anodized

Aged bronze 643E – – Relieved aged bronze Relieved aged bronze

Satin chrome (antimicrobial)

Satin stainless steel (antimicrobial)

U26D-AM 626-AM AM Clear over chrome

US32D-AM 630-AM

BHMA number

A, B, E C D & F

Satin stainless steel US32D, 630 (unless speciﬁed to match device)

Powder coat

Aged bronze, no relief

AM Clear over stainless steel

AM Clear over satin stainless steel US32D, 630

AM Clear over Satin Stainless Steel US32D, 630

AM Clear over anodized

Finishes

Touch bar trim options — Knurled

Embossed “Push” Braille (Caution-Stairwell), satin stainless steel only RSS, US32D only, red silk screen lettered “EMERGENCY EXIT ONLY – PUSH TO OPEN AND SOUND ALARM.”

* US32D and US15—available on 98 Series only ** Other custom logo touchbar trim and RAL color combinations available - consult factory

Von Duprin 98/99 Series • 69

69

98/99 Finishes

Finishes*

Color US

number

BHMA number

Color US

number

BHMA number

Chromium, polished

Anodized, aluminum

Chromium, dull US26D 626

Brass, polished US3 605

Brass, dull US4 606

US26 625

US28 628

Bronze, dull US10 612

Satin nickel

Available for 35A ONLY

Satin stainless steel

Duranodic dark bronze

Black 315 711

US15 619

US32D 630

313 710

Finishes

Pushpad options — Knurled

* Note: Durable powder coated ﬁnishes available at speciﬁc special request. PLEASE CONTACT FACTORY.

Special ﬁnishes

Color US

Satin chrome, Antimicrobial

Satin stainless steel, antimicrobial

Aged bronze 643e

Embossed “Push” Braille (Caution-Stairwell), satin stainless steel only RSS – (Emergency Exit – Push to open and sound alarm) – Red Silkscreen lettering on US32D

number

US26DAM

US32DAM

– –

BHMA number

626-AM

630-AM

70

70 • Von Duprin 98/99 Series

About Allegion

Allegion (NYSE: ALLE) creates peace of mind by pioneering safety and security. As a $2 billion provider of security solutions for homes and businesses, Allegion employs more than 7,800 people and sells products in more than 120 countries across the world. Allegion comprises 23 global brands, including strategic brands CISA

®

, Interﬂex®, LCN®, Schlage® and Von Duprin®.

For more, visit www.allegion.com

Allegion Von Duprin 98 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual