Page 1
ETS Series
Swing Door Operators
Features
The ECO ETS has a powerful electromotive drive that safely
and silently opens and closes door leaves up to 250kg in
weight, and up to 1600mm in width. This provides secure
automation for external doors that may experience strong
wind loads, and also for heavy fire protection doors.
Quiet and ecient
The ETS is extremely quiet and has a well engineered and
harmonious movement. It is these properties that make
the ETS such an effective all-rounder for public buildings,
hospitals, clinics and aged care facilities.
Fire and smoke protection
The ETS model ETS 64-R is approved as a hold-open device
for fire and smoke protection doors. In combination with a
lintel switch, it triggers the fire protection closer in the case
of a smoke activated alarm or power failure.
The Inverse function has been specially developed for
smoke extraction from buildings. The fire/smoke protection
function is reversed when the alarm is triggered, and the
door is opened by spring force to enable smoke extraction.
The feature will still be activated during a power cut, so an
emergency power supply is not necessary.
Simple assembly, operation and service
The ETS has a simple, user-friendly settings menu. This is
controlled via the LCD display panel and joystick function on
the control board.
Illuminated keys on the end caps allow easy access to
the Auto/Night/Manual/Hold Open/Exit functions so that
approved personnel can manage the device as required. The
operation of the device is also password protected.
Low Energy and Full Power settings
The ETS can be set for both Low Energy and Full Power
functions on site using the same drive - an additional
upgrade card is not necessary. The Full Power setting enables
automation for heavy doors that are used frequently and
require fast opening and closing sequences.
The Low Energy setting (only 4W on standby) has been
developed for private households, oces and work areas
where doors are used less frequently.
The starting power and closing power are also adjustable
for both Low Energy and Full Power settings, and there is an
adjustable start delay setting for the closing sequence.
Wind load compensation
The wind load control is there to smooth the operation of the
outer doors in different air pressure conditions right up to Wind
Force 9. A briefly occurring increased wind load (e.g. a strong
gust) is also recognised by the drive.
The control calculates the additional motor performance for
amplifying or reducing the drive, enabling the door to operate
effectively in a wide range of conditions.
Push + Go
Push + Go is a feature which if selected allows the door to
automatically open when it detects users pushing the door
manually.
April 2018
Page 2
Specifications
ECO-ETS73 ECO-ETS64-R
Closing force Size according to EN, continuously adjustable 3-7 4-6
Door width Doors up to 1600mm Yes -
Size according to EN
Doors up to 1400mm - Yes
Dimensions Length (mm) 689 689
Including mounting plate
Depth (mm) 120 (130)* 120 (130)*
Height (mm) 95 95
Ambient temperature Celcius -15° to +50° -15° to +50°
Relative humidity Maximum 85% Maximum 85%
Maximum Power consumption 560W (4W standby) 560W (4W standby)
Non-handed Ye s Ye s
Maximum opening speed adjustable 40° per second 40° per second
Maximum closing speed Adjustable (fixed if there is a power failure) 40° per second 40° per second
Hold-open time adjustable 0-60 seconds 0-60 seconds
Max. door opening angle 105° 105°
Suitable for fire and smoke control doors Yes Yes**
* 130mm with mounting plate ** includes integrated smoke detector and three fire relays
Accreditations
Fire rated
Successfully tested on fire doorset to AS 1530.4
Electromagnetic compatibility
Meets EN 61000-6-1 (emission) EN 61000-6-2 (immunity) standards
Accessories
Slide Rail Arm (ECO-ETS-SLIDERAIL)
Provides an automated push action when
positioned opposite the hinge side of the door,
and an automated pull action when positioned
on the hinge side of the door.
Standard Arm (ECO-ETS-ARM)
Provides an automated push action when
positioned opposite the hinge side of the door.
Mounting Plate for ETS (ECO -ETS-MP
The mounting plate provides additional fire
protection and/or fixing strength when used on
walls or narrow frame facings.
Open Stop for ETS (ECO- ETS-ST OP)
Mounted on the power unit to provide additional
mechanical open stop where required.
Push Plate Actuator (LCP25136)
Mounted on the power unit to provide additional
mechanical open stop where required.
Activation Sensor (ECO-ETS-ACTIVATION)
A radar motion detector which provides an
opening impulse for the ETS.
Safety Sensor (ECO -ETS-SAFETY)
An active infrared safety sensor for automatic
doors. Secures the movement area and stops or
reverses when obstacles are detected.
Continuous Cladding for Double Leaf Doors
(ECO-ETS-DOUBLE)
Provides a seamless stainless steel look across
the top of the header frame when two power
operators are installed above double doors.
Suitable for openings up to 2.6m wide.
April 2018
Page 3
217
B
76
62*
17
424
650
M6
24
23
26
Ø20
z
BA
Mounting and operating instructions
DIN right = as shown
DIN left = mirror-inverted
Fixing holes
Chassisprole
Lintel depth
Lower edge door frame
Axis of rotation
Lintel depth Min. width Max. door Rod assem- A B C
door leaf opening angle blies (mm) (mm) (mm)
(mm) (mm) (°) (art. no.)
-30...+20 740 105 0548-105 140 280 620
21...30 730 105 0548-105 130 280 620
31...40 720 105 0548-105 120 280 830
41...60 720 100 0548-105 120 280 830
61...70 720 95 0548-105 120 280 830
-30...+200 870 105 0548-105/02 60 385 830
217
A
76
56*
86**
424
650
B
B
M6
24
2326
Ø20
z
Mounting and operating instructions
DIN left = as shown
DIN right = mirror-inverted
Chassisprole
Upper edge door leaf
Mounting Options
217
424
650
358 45
76
17*
53**
M6
24
2326
Ø20
z
Mounting and operating instructions
Material:
1 Drive mechanism 0548-030 Covering aluminium
Drive mechanism 0548-031 Covering inox
incl.xingset 0548-107
1 Normal rods 0548-104
Normal rods KTL 0548-104/01
Procedure:
1. Mark out and drill the fastening holes on the lintel and the door leaf.
DIN right = as shown
DIN left = mirror-inverted
Fixing holes
Chassisprole
Lower edge door frame
130
317
76
524
750
385 385
M6
62**
17*
Mounting and operating instructions
DIN left = as shown
DIN right = mirror-inverted
Chassisprole
Upper edge door leaf
ETS with slide rail arm and automated pull action (hinge side)
689
95
185
90
26
C
Clamping piece
standard
Sliding bolt
38 mm
ETS with slide rail arm and automated push action (opposite hinge)
689
9566
161
26
C
Clamping piece
standard
Sliding bolt
14 mm
Lintel depth
+80
+200
+70
+200
-30
-30
Axis of rotation
ETS with standard arm and automated push action (opposite hinge)
ETS door mounted with special long track arm and automated pull function (hinge side)*
100
26
689
45
60
830
9575
170
Lintel depth
0...250
Sliding bolt
14 mm
Clamping piece
161
standard
66
95
~398
Clamping piece
standard
Lintel depth
+200
-30
689
*Long track arm can only be used in conjunction with a pull-side mounted ETS-73
April 2018
Loading...