Allegion 9952 Installation Instructions

Page 1
This is a printable pdf document.
For Smartphone-friendly version,
tap or click here.
Page 2
*47269026*
47269026-00
Exterior Gate Exit Device and Trim
#10-24
98/9952
Installation Instructions
Pour les instructions d’installation en français, scannez le code QR sur l’étiquette de l’emballage avec votre smartphone. Cela permettra d’accéder à des instructions d’installation interactives spécialisées et à des
informations spéciques aux produits.
Customer Service
1-877-671-7011 us.allegion.com
© Allegion 2019
Printed in U.S.A.
47269026 Rev. 4/19-a
Page 3
Digital Experience, Please Read!
For the best installation experience, scan the QR code on the product box
label with your Smartphone. This will give you access to specialized interactive installation instructions
as well as specic product information.
Page 4
1
2 3
Which way is your gate handed?
Right Hand Reverse (RHR)
Left Hand Reverse (LHR)
If the gate is Left Hand Reverse (LHR), the trim has to be rehanded as shown in step 2.
If RHR, go to step 3.
Remove templates from shipping tube and separate.
Cut on bold dotted line between Push and Pull side templates.
NOTE: If required for retrot,
additionally cut Push side template on thin dotted line (Reduce by no more than 2”).
If necessary, rehand trim from RHR to LHR
A. Remove Lower studs, cable mount, and spacer. B. Remove retaining clip and set screw, cam, and shear pin. C. Rotate lever 180 degrees to opposite side and reinstall shear pin and cam. D. Make sure cam is correct orientation. LHR will show “L” on cam. You may need to push up on cable slider to insert cam. E. Reinstall set screw and retaining clip. F. Put cable mount and spacer together. G. Install lower studs.
B
A
Left Hand Reverse (LHR) shown Right Hand Reverse (RHR) opposite
54
SIDE
PULL
SIDE
PUSH
Align push side template and prepare holes and cutout
A. Mark trim centerline 54” from
bottom of gate. B. Align template and mark holes. C. Prepare holes and cutout.
Install cylinder into trim
C
D
PUSH SIDE
TEMPLATE
4x Ø .375 thru one wall
Vertical Cable
Trim
18" between
trim and exit device centerlines
Gate edge for Push side LHR
Gate edge
for Push side RHR
4x drill and tap #10-24 UNC 2B thru one wall
Vertical Cable
Exit
2x Ø .196 thru
Device
Ø .385 x 82°
36" to bottom
of gate Remove material (one wall)
54"
Page 5
6
7
Align pull side template and prepare holes and cutout
A. Mark trim centerline 54” from
bottom of gate. B. Align template and mark holes. C. Prepare holes and cutout.
PULL SIDE
TEMPLATE
2x Ø .375 thru one wall
Remove material (one wall)
Trim
Trim
54" to bottom of gate
Vertical Cable
54"
8
Attach other end of cable to center slide
Attach cable to trim
9
Slide trim assembly into pull side of door
Page 6
10
11
12 13
Secure center slide with 2 screws
14
If necessary, cut the exit device
Temporarily remove anti-rattle clip
Secure trim with 4 screws and washers
Attach center case to gate
The 4 main screws are required.
The 2 security screws are optional.
15
Install end cap bracket and end cap
Check clearance for end cap
1.5” min.
Clearance should be 1.5” minimum.
If clearance is less, you will need to cut
the exit device.
16
Install the lift nger parts
Start screws but do not tighten.
Cover plate flush
Page 7
17
18
Adjust the lift nger
A. Hold the trim lever down during adjustment. B. Loosen retaining screw. C. Turn the bottom adjusting screw clockwise until latchbolt retracts fully. D. Tighten retaining screw.
B
C
A
19 20
Install center case cover
C
21
Install strike along center line on post and adjust as needed
There should be a 3/16” gap between the center case cover and the strike roller.
3/16”
Install strike support screws
Install Latchbolt rub plate
Remove adhesive and place along center line of post. The surface should be free from grease and debris to ensure a good bond.
Page 8
22
23
Test door function
A. Use key in cylinder to lock and unlock the trim, verifying locking function.
B. Press the pushpad on the exit device
and verify that the gate opens properly.
C. With trim unlocked, pull down on the lever and verify that gate opens properly.
If the product does not function as
expected, re-check the installation steps,
or call Customer Service at:
1-877-671-7011
Cable Removal
(If the cable was installed in wrong position)
A cable removal tool was included with
device. Slot in tool ts over cable, holding
tabs down. Pull on cable snap to loosen cable for removal.
cable
slot
snap
a
b
Loading...